IP 5K4K란?

IP Code는 보통 international protection Code로 알리어지거나 또는 Ingress protection으로 불려지고 있다. 모두 먼지와 물의 침투에 관한 등급 표기 방식이다.

각 규격 별로 약간의 다른 등급표기가 있으나 의미상 내용은 크게 다르지 않으나 유사한 세부적 분류의 표기법이 있다.

다음은 규격의 전부 또는 일부로써 IP code를 다루고 있는 규격 사례들이며 각 규격의 적용분야는 서로 다르지만 의도하는 목적은 같다.

1. DIN EN 60068-2-18 ; Environmental testing: water
2. DIN EN 60529; VDE 0470-1 ;Degrees of Protection provided by Enclosures (IP-Code)
3. ISO 20653 도로 차량 — Degrees of protection (IP-Code) (replacing DIN 40050)
4. MIL-STD-810G Rain Dust
5. NEMA 250 : 전기공업협회
6. RTCA/DO-160G ; Waterproofness
7. VW 80000 ; Automotive

IP Code 표기법

APN_시험인증_IP_Code_IP4K5K

메르세데스 벤츠 회사 표준 MBN LV 124-1 : 모터 차량의 전기 및 전자 부품에 3,5t - 일반 요구 사항까지, 시험 조건 및 시험, Part 1 : 전기 요구 사항 및 시험 12 V On – Board Electrical System.

MBN LV 124-1 규격은 Benz, BMW, Audi, 다임러, Porsche, Volkswagen 등 완성차 제조사 들이 Working Group 4.9 (전자 부품의 공급 업체 하드웨어 품질 프로세스 보증)에 참여하여 작성한 이들 회사의 회사 공통 규격이다.

이 규격은 Part 1 : Part 1 : 전기 요구 사항 및 시험 12 V 온 - 보드 전기 시스템. 및 Part 2 : Environmental Requirements 등 두 가지의 규격으로 나눠진다.

이 규격 MEN LV124는 Part 1에서 Electrical requirements and tests 의 E-01~ E22, Part 2에서 Environmental requirements의 8. Mechanical 은 M-01~ M-06, 9. 기후 요구 사항 및 테스트는 K-01~ K-18, 11. Life tests는 L-01~L3으로 분류된다.

MBN LV 124 Download

Download : Analysis of one TPO membrane per ASTM D6878_D6878M-13

Analysis of one TPO membrane per ASTM D6878/D6878M-13.

아래는 적용되는 분석기법입니다.

1. ASTM D 6878/D : Brittleness Point per ASTM D2137, Method B
2. ASTM D 6878/D : Ozone Resistance per ASTM D 1149 (Exposed to 100 mPa ozone in air @40°C, wrapped around a 3″ mandrel for 166 hrs exposure) – OUTSOURCED
3. ASTM D 6878/D : Breaking Strength per ASTM D751, grab method – MD
4. ASTM D 6878/D : Breaking Strength per ASTM D751, grab method – XMD
5. ASTM D 6878/D : Elongation at Reinforcement Break per ASTM D751, grab method – MD
6. ASTM D 6878/D : Elongation at Reinforcement Break per ASTM D751, grab method – XMD
7. ASTM D 6878/D : Factory Seam Strength @ 2 in/min (12 in x 1 in specimen) per ASTM D751,grab method
8. ASTM D 6878/D : Heat Aging, 5376 hrs (224 days) @ 116°C, per ASTM D573
9. ASTM D 6878/D : Linear Dimensional Change, 6 hr @ 70°C (158°F), per ASTM D1204
10. ASTM D 6878/D : Post Heat Aging: Breaking Strength per ASTM D751, grab method – MD
11. ASTM D 6878/D : Post Heat Aging: Breaking Strength per ASTM D751, grab method – XMD
12. ASTM D 6878/D : Post Heat Aging: Elongation at Reinforcement Break per ASTM D751, grab method – MD
13. ASTM D 6878/D : Post Heat Aging: Elongation at Reinforcement Break per ASTM D751, grab method – XMD
14. ASTM D 6878/D : Post Heat Aging: Tearing Strength, 2 in/min (8 in x 8 in specimen) per ASTMD751 – MD
15. ASTM D 6878/D : Post Heat Aging: Tearing Strength, 2 in/min (8 in x 8 in specimen) per ASTMD751 – XMD
16. ASTM D 6878/D : Post Heat Aging: Weight Change (mass)
17. ASTM D 6878/D : Tearing Strength, 2 in/min (8 in x 8 in specimen), per ASTM D751 – MD
18. ASTM D 6878/D : Tearing Strength, 2 in/min (8 in x 8 in specimen), per ASTM D751 – XMD
19. ASTM D 6878/D : Thickness, Coating Over Fabric or Scrim (weathering side only) per ASTM D7635
20. ASTM D 6878/D : Thickness, Sheet-Overall per ASTM D751
21. ASTM D 6878/D : Water Absorption, 166 hrs @ 70°C (158°F) (mass) per ASTM D471 – Performed on top coating material ONLY
22. ASTM D 6878/D : Weather Resistance per ASTM G 155 at 0.35 W/(m²•nm) at 340 nm (8000 hrs)

22. MISCELLANEOUS MATERIALS

22-1) ANSI A108.10-2009 ; Installation of Grout in Tilework;

22-2) ANSI A108.1-2009 ; Specification for the Installation of Ceramic Tile with Portland Cement Mortar;

22-3) ANSI A108.4-2009 ; Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile Setting Epoxy Adhesive;

22-4) ANSI A108.5-2009 ; Installation of Ceramic Tile with Dry-Set Portland Cement Mortar or Latex-Portland Cement Mortar;

22-5) ANSI A108.6-2009 ; Installation of Ceramic Tile with Chemical Resistant, Water Cleanable Tile Setting and Grouting Epoxy;

22-6) ANSI A108.7-2009 ; Specification for Electrically Conductive Ceramic Tile Installed with Conductive Dry-Set Portland Cement Mortar;

22-7) ANSI A108.8-2009 ; Installation of Ceramic Tile with Chemical Resistant Furan Mortar and Grout;

22-8) ANSI A108.9-2009 ; Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout;

22-9) ANSI A118.1-2009 ; Specification for Dry-Set Portland Cement Mortar;

22-10) ANSI A118.2-2009 ; Specifications for Conductive Dry-set Portland Cement Mortar;

22-11) ANSI A118.3-2009 ; Specifications for Chemical Resistant Water Cleanable Tile Setting and Grouting Epoxy and Water Cleanable Tile Setting Epoxy Adhesive;

22-12) ANSI A118.4-2009 ; Specifications Furan Latex – Portland Cement Mortar;

22-13) ANSI A118.5-2009 ; Specifications for Chemical Resistant Furan;

22-14) ANSI A118.6-2009 ; Specifications for Ceramic Tile Grouts;

22-15) ANSI A118.8-2009 ; Specifications for Modified Epoxy Emulsion Mortar/Grout;

22-16) ANSI A136.1-2009 ; Organic Adhesives for Installation of Ceramic Tile;

22-17) ANSI A137.1-2008 ; Specification for Ceramic Tile;

22-18) ANSI A137.1-2008 ; Specifications for Ceramic Tile;

22-19) ANSI Z 97.1-2009 ; Safety Performance Specifications and Methods of Tests for Transport Safety Glazing Materials Used in Building;

22-20) ASTM A116 – 05 ASTM A121 – 07 ; Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

22-21) ASTM A121 – 07 ; Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

22-22) ASTM A368 – 95a(2009) ; 스테인레스 스틸 와이어 물가에 대한 표준 규격

22-23) ASTM A392 – 07 ; Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric

22-24) ASTM A475 – 03(2009)e1 ; Standard Specification for Zinc-Coated Steel Wire Strand

22-25) ASTM A492 – 95(2009) ; 스테인레스 스틸 와이어 로프에 대한 표준 규격

22-26) ASTM A510 – 08 ; Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, 탄소강

22-27) ASTM A586 – 04a(2009)e1 ; Standard Specification for Zinc-Coated Parallel and Helical Steel Wire Structural Strand

22-28) ASTM A603 – 98(2009)e1 ; Standard Specification for Zinc-Coated Steel Structural Wire Rope

22-29) ASTM A817 – 07 ; Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire

22-30) ASTM A824 – 01(2007) ; 체인 연결 담 사용을위한 금속 입히는 강철 Marcelled 텐션 와이어에 대한 표준 규격

22-31) ASTM C1014 – 08 ; Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation

22-32) ASTM C1029 – 09 ; Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

22-33) ASTM C1036 – 06 ; Standard Specification for Flat Glass

22-34) ASTM C1048 – 04 ; Standard Specification for Heat-Treated Flat Glass—Kind HS, Kind FT Coated and Uncoated Glass

22-35) ASTM C1071 – 05e1 ; Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material)

22-36) ASTM C1193 – 09 ; Standard Guide for Use of Joint Sealants

22-37) ASTM C1193 – 09 ; Standard Guide for Use of Joint Sealants

22-38) ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

22-39) ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

22-40) ASTM C1363 – 05 ; Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus

22-41) ASTM C167 – 09 ; Standard Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations

22-42) ASTM C177 – 04 ; Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

22-43) ASTM C195 – 07 ; Standard Specification for Mineral Fiber Thermal Insulating Cement

22-44) ASTM C196 – 00(2005) ; Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement

22-45) ASTM C208 – 08a ; Standard Specification for Cellulosic Fiber Insulating Board

22-46) ASTM C209 – 07ae1 ; Standard Test Methods for Cellulosic Fiber Insulating Board

22-47) ASTM C240 – 08e1 ; Standard Test Methods of Testing Cellular Glass Insulation Block

22-48) ASTM C335 – 05ae1 ; Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation

22-49) ASTM C411 – 05 ; Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation

22-50) ASTM C449 – 07 ; Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement

22-51) ASTM C509 – 06 ; Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material

22-52) ASTM C516 – 08 ; Standard Specification for Vermiculite Loose Fill Thermal Insulation

22-53) ASTM C518 – 04 ; Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

22-54) ASTM C520 – 04 ; Standard Test Methods for Density of Granular Loose Fill Insulations

22-55) ASTM C533 – 09 ; Standard Specification for Calcium Silicate Block and Pipe Thermal Insulation

22-56) ASTM C534 / C534M – 08 ; Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form

22-57) ASTM C542 – 05 ; Standard Specification for Lock-Strip Gaskets

22-58) ASTM C547 – 07e1 ; Standard Specification for Mineral Fiber Pipe Insulation

22-59) ASTM C549 – 06 ; Standard Specification for Perlite Loose Fill Insulation

22-60) ASTM C552 – 07 ; Standard Specification for Cellular Glass Thermal Insulation

22-61) ASTM C553 – 08 ; Standard Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications

22-62) ASTM C564 – 09a ; Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

22-63) ASTM C578 – 09e1 ; Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

22-64) ASTM C591 – 09 ; Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation

22-65) ASTM C592 – 08a ; Standard Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type)

22-66) ASTM C610 – 09e1 ; Standard Specification for Molded Expanded Perlite Block and Pipe Thermal Insulation

22-67) ASTM C612 – 09 ; Standard Specification for Mineral Fiber Block and Board Thermal Insulation

22-68) ASTM C665 – 06 ; Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing

22-69) ASTM C716 – 06 ; Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials

22-70) ASTM C719 – 93(2005) ; Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)

22-71) ASTM C726 – 05e1 ; Standard Specification for Mineral Fiber Roof Insulation Board

22-72) ASTM C728 – 05(2010) ; Standard Specification for Perlite Thermal Insulation Board

22-73) ASTM C739 – 08 ; Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

22-74) ASTM C764 – 07 ; Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation

22-75) ASTM C794 – 06 ; Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants

22-76) ASTM C834 – 10 ; Standard Specification for Latex Sealants

22-77) ASTM C864 – 05 ; Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers

22-78) ASTM C916 – 85(2007) ; Standard Specification for Adhesives for Duct Thermal Insulation

22-79) ASTM C919 – 08 ; Standard Practice for Use of Sealants in Acoustical Applications

22-80) ASTM C920 – 08 ; Standard Specification for Elastomeric Joint Sealants

22-81) ASTM C991 – 08e1 ; Standard Specification for Flexible Fibrous Glass Insulation for Metal Buildings

22-82) ASTM D1003 – 07e1 ; Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics

22-83) ASTM D1044 – 08 ; Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion

22-84) ASTM D1204 – 08 ; Standard Test Method for Linear Dimensional Changes of Nonrigid

22-85) ASTM D1327 – 04 ; Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing

22-86) ASTM D146 – 04 ; Standard Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing

22-87) ASTM D1593 – 09 ; Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting

22-88) ASTM D1668 – 97a(2006) ; Standard Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing

22-89) ASTM D173 – 03 ; Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing

22-90) ASTM D2103 – 08 ; Standard Specification for Polyethylene Film and Sheeting

22-91) ASTM D2126 – 09 ; Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

22-92) ASTM D2178 – 04 ; Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

22-93) ASTM D226 / D226M – 09 ; Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

22-94) ASTM D227 – 03 ; Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

22-95) ASTM D25 – 99(2005) ; Standard Specification for Round Timber Piles

22-96) ASTM D2626 – 04 ; Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

22-97) ASTM D2628 – 91(2005) ; Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements

22-98) ASTM D2842 – 06 ; Standard Test Method for Water Absorption of Rigid Cellular Plastics

22-99) ASTM D2843 – 10 ; Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics

22-100) ASTM D3294 – 09 ; Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes

22-101) ASTM D3406 – 95(2006) ; Standard Specification for Joint Sealant, Hot-Applied, Elastomeric-Type, for Portland Cement Concrete Pavements

22-102) ASTM D3468 – 99(2006)e1 ; Standard Specification for Liquid-Applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing

22-103) ASTM D3667 – 05 ; Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors

22-104) ASTM D3678 – 97(2008)e1 ; Standard Specification for Rigid Poly(염화 비닐) (PVC) Interior-Profile Extrusions

22-105) ASTM D3679 – 09a ; Standard Specification for Rigid Poly(염화 비닐) (PVC) Siding

22-106) ASTM D3771 – 03(2007) ; Standard Specification for Rubber Seals Used in Concentrating Solar Collectors

22-107) ASTM D3832 – 79(2006) ; Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems

22-108) ASTM D3841 – 97(2008)e1 ; Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels

22-109) ASTM D41 – 05 ; Standard Specification for Asphalt Primer Used in Roofing, Damp proofing, and Waterproofing

22-110) ASTM D43 – 00(2006) ; Standard Specification for Coal Tar Primer Used in Roofing, Damp proofing, and Waterproofing

22-111) ASTM D449 – 03(2008) ; Standard Specification for Asphalt Used in Damp proofing and Waterproofing

22-112) ASTM D450 – 07 ; Standard Specification for Coal-Tar Pitch Used in Roofing, Damp proofing, and Waterproofing

22-113) ASTM D4802 – 02 ; Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet

22-114) ASTM D543 – 06 ; Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

22-115) ASTM D635 – 06 ; Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

22-116) ASTM D638 – 08 ; Standard Test Method for Tensile Properties of Plastics

22-117) ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

22-118) ASTM D6690 – 07 ; Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

22-119) ASTM D695 – 08 ; Standard Test Method for Compressive Properties of Rigid Plastics

22-120) ASTM D882 – 09 ; Standard Test Method for Tensile Properties of Thin Plastic Sheeting

22-121) ASTM E119 – 09C ; 건물 건축 재료의 화재 시험에 대한 표준 시험 방법

22-122) ASTM E84 – 10 ; Standard Test Method for Surface Burning Characteristics of Building Materials

22-123) ASTM F1183 – 96(2006) ; Standard Specification for Aluminum Alloy Chain Link Fence Fabric

22-124) BDS 1301 : 1990 ; Specification for Glazed Earthenware Wall Tiles;

22-125) BDS 1301:1990 ; Specification for Glazed Earthenware Wall Tiles;

22-126) BDS 1493:1994 ; Glossary of terms used in refractory

22-127) BDS 1494:1994 ; Dimension of refractory bricks

22-128) BDS 1495:1994 ; High aluminium refractory bricks

22-129) BDS 809:1973 ; Specification for Wood Poles for Overhead Power and Telecommunication Lines;

22-130) BDS 885:1979 ; Method for Measuring Viscosity Number and K-Value of PVC Resins;

22-131) BDS 886:1978 ; Method for Direct Measuring the Specific Gravity of Plastics;

22-132) BDS 887:1978 ; Method for Measuring Deformation under Heat of Flexible Rigid PVC Compounds;

22-133) BDS 888:1978 ; Method for Measuring Temperature of Deflection under Load;

22-134) BDS 889:1978 ; Method for Measuring the Vicat Softening Temperature (VST) of Thermoplastics;

22-135) BDS 890:1978 ; Method for Measuring the Water Absorption at Room Temperature and Bolling Water Absorption of Plastics;

22-136) BDS 891:1978 ; Method for Measuring the Flexural Modulus of Plastics;

22-137) BDS 892:1978 ; Method for Measuring the Resistance to Tear Propagation of Flexible Plastics, Film or Sheeting;

22-138) BS 6431 ; Floor and Wall Tiles;

22-139) BS 6431 Part 1 1983 ; Specification for Classification and Making, Including Definitions and Characteristics;

22-140) BS 6431 Part 1 to Part 23 ; Ceramic Floor and Wall Tiles.

22-141) BS 6431 Part 10 1984 ; Method for Determination of Dimensions and Surface Quality;

22-142) BS 6431 Part 11 1983 ; Method for Determination of Water Absorption;

22-143) BS 6431 Part 12 1983 ; Method for Determination of Modulus of;

22-144) BS 6431 Part 13 1986 ; Method for Determination of Scratch Hardness of Surface According to Mhos;

22-145) BS 6431 Part 14 1983 ; Method for Determination of Resistance to Abrasion of Unglazed Tiles;

22-146) BS 6431 Part 15 1983 ; Method for Determination of Linear Thermal Expansion;

22-147) BS 6431 Part 16 1983 ; Method for Determination of Resistance to Thermal Shock;

22-148) BS 6431 Part 17 1983 ; Method for Determination of Crazing Resistance-Glazed Tiles;

22-149) BS 6431 Part 18 1983 ; Method for Determination of Chemical Resistance-Unglazed Tiles;

22-150) BS 6431 Part 19 1984 ; Method for Determination of Chemical Resistance-Unglazed Tiles;

22-151) BS 6431 Part 2 1984 ; Specification for Struded Ceramic Tiles with Low Water Absorption (그것< 3%) Group A1;

22-152) BS 6431 Part 20 1984 ; Method for Determination of Resistance to Surface Abrasion-Glazed Tiles;

22-153) BS 6431 Part 23 1986 ; Specification for Sampling and Basis for Acceptance;

22-154) BS 6431 Part 3 ; Extruded Ceramic Tiles with a Water Absorption of 3% < 6%. Group A 11a;

22-155) BS 6431 Part 3 섹션 3.1 1986 ; Specification for General Products;

22-156) BS 6431 Part 3 섹션 3.2 1986 ; Specification for Products Terre Cuite, Cotto, Baldosion Catalan;

22-157) BS 6431 Part 4 ; Extruded Ceramic Tiles with a Water Absorption of 6% <그것< 10%. Group A11b;

22-158) BS 6431 Part 4 ; 섹션 4.2 1986

22-159) BS 6431 Part 4 ; Specification for General Products;

22-160) BS 6431 Part 5 1986 ; Specification for Extruded Ceramic Tiles with a Water Absorption of E>10%, Group A111;

22-161) BS 6431 Part 6 1984 ; Specification for Dust-prestressed Ceramic Tiles with a Low-Water Absorption (그것<3%)Group B1;

22-162) BS 6431 Part 7 1986 ; Specification for Dust-prestressed Ceramic Tiles with a Water Absorption of 3% <E £ 6%. Group B11a;

22-163) BS 6431 Part 8 1986 ; Specification for Dust-prestressed Ceramic Tiles with Water Absorption of 6% < E £ 10%. Group B11b;

22-164) BS 6431 Part 9 1984 ; Specification for Dust-Prestressed Ceramic Tiles with a Water Absorption of E >10%. Group B111;

22-165) IS 10102:1982 ; Technical supply conditions for Rivets.

22-166) IS 110:1968 ; Specification for Ready Mixed Paint, Brushing, Grey Filler, for Enamels, for Use Over Primers (First Revision);

22-167) IS 1900:1974 ; Method of Testing Wood Poles;

22-168) IS 1902:1961 ; Code of Practice for Preservation of Bamboo and Cane for Non-structural Purposes;

22-169) IS 1929:1982 ; Specification for Hot Forged Steel Rivets for Hot Closing (12 에 36 mm diameter) (First Revision);

22-170) IS 2155:1982 ; Specification for Cold-Forged Solid Steel Rivets for Hot Closing (6 에 16 mm diameter) (First Revision);

22-171) IS 2365:1977 ; Specification for Steel Wire Suspension Ropes for Lifts, Elevators and Hoists (First Revision).

22-172) IS 2643:1975 ; Dimensions for Pipe Threads for Fastening Purposes;

22-173) IS 2907:1964 ; Specification for Non-ferrous Rivets (1.6 mm to 10 mm)

22-174) IS 2998:1981 ; Specification for Cold Forged Steel Rivets for Cold Closing (1 에 16 mm diameter) (First Revision);

22-175) IS 3337:1978 ; Specification for Ballies for General Purposes (First Revision);

22-176) IS 345:1952 ; Specification for Wood Filler, Transparent, Liquid;

22-177) IS 3709:1966 ; Specification for Mastic Cement for Bedding of Metal Windows;

22-178) IS 419:1967 ; Specification for Putty for Use on Window Frames (First Revision);

22-179) IS 421:1953 ; Specification for Jointing Paste, for Bedding Moldings on Coaching Stock;

22-180) IS 423:1961 ; Specification for Plastic Wood, for Joiners’ Filler (revised);

22-181) IS 424:1965 ; Specification for Plastic Asphalt (revised);

22-182) IS 554:1975 ; Dimensions for Pipe Threads where Pressure Tight Joints are Required on the Threads (Second Revision);

22-183) IS 6711:1972 ; Code of Practice for Maintenance of Wood Poles for Overhead Power and Telecommunications Lines.

22-184) IS 6874:1973 ; Method of Tests for Round Bamboos;

22-185) IS 7164:1973 ; Specification for Stopper.

22-186) IS 8242:1976 ; Methods of Tests for Split Bamboo;

22-187) IS 8295:1976 ; Specification for Bamboo Chicks, Part I Fine;

22-188) IS 9096:1979 ; Code of Practice for Preservation of Bamboos for Structural Purposes.

22-189) ISO 10080:1990 ; Refractory Products-Classification of Dense, Shaped Acid-Resisting Products;

22-190) ISO 10081:1991 ; Basic Refractory Products-Classification-Part I: Products Containing Less Than 7% Residual Carbon.

22-191) ISO 10563:1991 ; Building Construction-Sealants for Joints-Determination of Change in Mass and Volume;

22-192) ISO 10590:1991 ; Building Construction-Sealants-Determination of Adhesion/Cohesion Properties at Maintained Extension after Immersion in Water;

22-193) ISO 10591 : 1991 ; Building Construction-Sealants-Determination of Adhesion/Cohesion Properties after Immersion in Water.

22-194) ISO 1109:1975 ; Refractory Products-Classification of Dense Shaped Refractory Products;

22-195) ISO 1146:1988 ; Pyrometric Reference Cones for Laboratory Use-Specification;

22-196) ISO 1893:1989 ; Refractory Products-Determination of Refractoriness-Under-Load (differential with rising temperature);

22-197) ISO 1927:1984 ; Prepared Unshaped Refractory Materials (Dense and Insulating) 분류;

22-198) ISO 2245:1990 ; Shaped Insulating Refractory Products-Classification;

22-199) ISO 2444 : 1988 ; Joints in Buildings-Vocabulary;

22-200) ISO 2477:1987 ; Shaped Insulating Refractory Products-Determination of Permanent Change in Dimensions on Heating;

22-201) ISO 2478:1987 ; Dense Shaped Refractory Products-Determination of Permanent Change in Dimensions on Heating;

22-202) ISO 3187:1989 ; Refractory Products-Determination of Creep in Compression;

22-203) ISO 3867:1982 ; Agglomerated Cork-Material of Expansion Joints for Construction and Building Test-Methods;

22-204) ISO 3869:1981 ; Agglomerated Cork-Filler Material of Expansion Joints for Construction and Buildings -Characteristics, Sampling and Packing;

22-205) ISO 3934:1978 ; Rubber Building Gaskets-Materials in Preformed Solid Vulcanizates Used for Sealing Glazing and Panels-Specification;

22-206) ISO 3934:1978 ; Rubber Building Gaskets-Materials in Preformed Solid Vulcanizates Used for Sealing Glazing and Panels-Specification;

22-207) ISO 4633:1983 ; Rubber Seals-Joint Rings for Water Supply, Drainage and Sewerage Pipelines-Specification for Materials;

22-208) ISO 4633:1983 ; Rubber Seals-Joint Rings for Water Supply, Drainage and Sewerage Pipelines-Specifications for Materials;

22-209) ISO 4635:1982 ; Rubber, Vulcanized-Preformed Compression Seals for Use

22-210) ISO 4635:1982 ; Rubber, Vulcanized-Preformed Compression Seals for Use Between Concrete Motorway Paving Sections-Specification for Material;

22-211) ISO 5013:1985 ; Refractory Products-Determination of Modulus of Rupture at Elevated Temperatures;

22-212) ISO 5014:1986 ; Refractory Products-Determination of Modulus of Rupture at Ambient Temperature;

22-213) ISO 5015-6:1984 ; Refractory Bricks-Dimensions-Part 6: Basic Bricks for Oxygen Steel Making Converters;

22-214) ISO 5016:1986 ; Shaped Insulating Refractory Products-Determination of Bulk Density and True Porosity;

22-215) ISO 5017:1988 ; Dense Shaped Refractory Products-Determination of Bulk Density,

22-216) ISO 5018:1983 ; Refractory Materials-Determination of True Density;

22-217) ISO 5019-1:1984 ; Refractory Bricks-Dimensions-Part I: Rectangular Bricks;

22-218) ISO 5019-2:1984 ; Refractory Bricks-Dimensions-Part 2: Arch Bricks;

22-219) ISO 5019-3:1984 ; Refractory Bricks-Dimensions-Part 3: Rectangular Checker Bricks for Regenerative Furnace;

22-220) ISO 5022:1979 ; Shaped Refractory Products-Sampling and Acceptance Testing;

22-221) ISO 528:1983 ; Refractory Products-Determination of Pyrometric Cone Equivalent (refractoriness);

22-222) ISO 5417-1986 ; Refractory Bricks for Use in Rotary Kilns-Dimensions;

22-223) ISO 5419-4:1988 ; Refractory Bricks-Dimensions-Part 4: Dome Bricks for Electric arc Furnace Roofs;

22-224) ISO 5892:1981 ; Rubber Building Gaskets-Materials for Preformed Solid Vulcanized Structural Gaskets-Specification;

22-225) ISO 5892:1981 ; Rubber Building Gaskets-Materials for Preformed Solid Vulcanized Structural Gaskets-Specification;

22-226) ISO 6447:1983 ; Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings-Specification for Material;

22-227) ISO 6447:1991 ; Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings- Specification for Material;

22-228) ISO 6589:1983 ; Joints in Building-Laboratory Method of Test for Air Permeability of Joints;

22-229) ISO 7389:1987 ; Building Construction-Jointing Products-Determination of Elastic Recovery;

22-230) ISO 7390:1987 ; Building Construction-Jointing Products-Determination of Resistance to Flow;

22-231) ISO 7727:1984 ; Joints in Building-Principles for Jointing of Building Components-Accommodation of Dimensional Deviations During Construction;

22-232) ISO 8339:1984 ; Building Construction-Jointing Products-Sealants-Determination of Tensile Properties;

22-233) ISO 8340:1984 ; Building Construction-Jointing Products-Sealants-Determination of Tensile Properties at Maintained Extension;

22-234) ISO 8394:1988 ; Building Construction-Jointing Products-Determination of Extrudability of One-Component Sealants;

22-235) ISO 8656:1988 ; Refractory Products-Sampling of Raw Materials and Unshaped Products;

22-236) ISO 8840:1987 ; Refractory Materials-Determination of Bulk Density of Granular Materials (Grain Density);

22-237) ISO 8890:1988 ; Dense Shaped Refractory Products-Determination of Resistance to Sulfuric Acid;

22-238) ISO 8894-1:1987 ; Refractory Materials-Determination of Thermal Conductivity-

22-239) ISO 8894-2:1990 ; Refractory Materials-Determination of Thermal Conductivity-

22-240) ISO 8895:1986 ; Shaped Insulating Refractory Products-Determination of Cold Crushing Strength;

22-241) ISO 9046:1987 ; Building Construction-Sealants-Determination of Adhesion/ Cohesion Properties at Constant Temperature;

22-242) ISO 9047:1989 ; Building Construction-Sealants-Determination of Adhesion/ Cohesion Properties at Variable Temperatures;

22-243) ISO 9205:1988 ; Refractory Bricks for Use in Rotary Kilns-Hot-face Identification Marking;

22-244) ISO 9331:1991 ; Rubber Seals Joint Rings for Hot Water Supply Pipelines up to 110oC Specifications for the Material.

22-245) ISO 9631:1991 ; Rubber Seals-Joint Rings for Hot Water Supply Pipelines up to 110oC Specifications for the Material;1-1) ANSI A108.1-2009 ; Specifications for the Installation of Ceramic Tile with Portland Cement Mortar;

21. SANITARY APPLIANCES AND WATER FITTINGS

21-1) ASTM A377 – 03(2008)e1 ; Standard Index of Specifications for Ductile-Iron Pressure Pipe

21-2) ASTM A53 / A53M – 07 ; 파이프에 대한 표준 규격, 강철, 블랙과 핫 담근, 아연 도금, 용접 및 원활한

21-3) ASTM A74 – 09 ; Standard Specification for Cast Iron Soil Pipe and Fittings

21-4) ASTM B209 – 07 ; Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

21-5) ASTM B251 – 02e1 ; Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube

21-6) ASTM B302 – 07 ; Standard Specification for Threadless Copper Pipe, Standard Sizes

21-7) ASTM B306 – 09 ; Standard Specification for Copper Drainage Tube (DWV)

21-8) ASTM B42 – 02e1 ; Standard Specification for Seamless Copper Pipe, Standard Sizes

21-9) ASTM B42 – 02e1 ; Standard Specification for Seamless Copper Pipe, Standard Sizes

21-10) ASTM B429 / B429M – 06 ; Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube

21-11) ASTM B43 – 09 ; Standard Specification for Seamless Red Brass Pipe, Standard Sizes

21-12) ASTM B447 – 07 ; Standard Specification for Welded Copper Tube

21-13) ASTM B745 / B745M – 97(2005) ; Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

21-14) ASTM B75 – 02 ; Standard Specification for Seamless Copper Tube

21-15) ASTM B88 – 09 ; Standard Specification for Seamless Copper Water Tube

21-16) ASTM C14 – 07 ; Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe

21-17) ASTM C425 – 04(2009) ; Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings

21-18) ASTM C443 – 05ae1 ; Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

21-19) ASTM C508 / C508M – 00(2009)e1 ; Standard Specification for Asbestos-Cement Underdrain Pipe

21-20) ASTM C564 – 09a ; Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

21-21) ASTM C654 – 05a ; Standard Specification for Porous Concrete Pipe

21-22) ASTM C700 – 09 ; Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

21-23) ASTM C76 – 10a ; Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

21-24) ASTM D1527 – 99(2005) ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

21-25) ASTM D1785 – 06 ; Standard Specification for Poly(염화 비닐) (PVC) Plastic Pipe, Schedules 40, 80, and 120

21-26) ASTM D1869 – 95(2005)e1 ; Standard Specification for Rubber Rings for Asbestos-Cement Pipe

21-27) ASTM D2235 – 04 ; Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

21-28) ASTM D2239 – 03 ; Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

21-29) ASTM D2241 – 09 ; Standard Specification for Poly(염화 비닐) (PVC) Pressure-Rated Pipe (SDR Series)

21-30) ASTM D2321 – 09 ; Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications ASTM D2464 – 06 Standard Specification for Threaded Poly(염화 비닐) (PVC) Plastic Pipe Fittings, Schedule 80

21-31) ASTM D2466 – 06 ; Standard Specification for Poly(염화 비닐) (PVC) Plastic Pipe Fittings, Schedule 40ASTM D2467 – 06 Standard Specification for Poly(염화 비닐) (PVC) Plastic Pipe Fittings, Schedule 80

21-32) ASTM D2564 – 04(2009)e1 ; Standard Specification for Solvent Cements for Poly(염화 비닐) (PVC) Plastic Piping Systems

21-33) ASTM D2609 – 02(2008) ; Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

21-34) ASTM D2657 – 07 ; Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

21-35) ASTM D2661 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, 낭비, and Vent Pipe and Fittings

21-36) ASTM D2661 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, 낭비, and Vent Pipe and Fittings

21-37) ASTM D2665 – 09 ; Standard Specification for Poly(염화 비닐) (PVC) Plastic Drain, 낭비, and Vent Pipe and Fittings

21-38) ASTM D2672 – 96a(2009) ; Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement

21-39) ASTM D2729 – 03 ; Standard Specification for Poly(염화 비닐) (PVC) Sewer Pipe and Fittings

21-40) ASTM D2737 – 03 ; Standard Specification for Polyethylene (PE) Plastic Tubing

21-41) ASTM D2751 – 05 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

21-42) ASTM D2846 / D2846M – 09B ; Standard Specification for Chlorinated Poly(염화 비닐) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

21-43) ASTM D2846 / D2846M – 09B ; Standard Specification for Chlorinated Poly(염화 비닐) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

21-44) ASTM D2855 – 96(2010) ; Standard Practice for Making Solvent-Cemented Joints with Poly(염화 비닐) (PVC) Pipe and Fittings

21-45) ASTM D2949 – 01a(2008)e1 ; Standard Specification for 3.25-in. Outside Diameter Poly(염화 비닐) (PVC) Plastic Drain, 낭비, and Vent Pipe and Fittings

21-46) ASTM D3034 – 08 ; Standard Specification for Type PSM Poly(염화 비닐) (PVC) Sewer Pipe and Fittings

21-47) ASTM D3139 – 98(2005) ; Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

21-48) ASTM D3212 – 07 ; Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

21-49) ASTM F402 – 05 ; Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

21-50) ASTM F405 – 05 ; Standard Specification for Corrugated Polyethylene (PE) Pipe and Fittings

21-51) ASTM F409 – 02(2008) ; Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

21-52) ASTM F437 – 09 ; Standard Specification for Threaded Chlorinated Poly(염화 비닐) (CPVC) Plastic Pipe Fittings, Schedule 80

21-53) ASTM F438 – 09 ; Standard Specification for Socket-Type Chlorinated Poly(염화 비닐) (CPVC) Plastic Pipe Fittings, Schedule 40

21-54) ASTM F441 / F441M – 09 ; Standard Specification for Chlorinated Poly(염화 비닐) (CPVC) Plastic Pipe, Schedules 40 and 80

21-55) ASTM F442 / F442M – 09 ; Standard Specification for Chlorinated Poly(염화 비닐) (CPVC) Plastic Pipe (SDR–PR)

21-56) ASTM F493 – 04 ; Standard Specification for Solvent Cements for Chlorinated Poly(염화 비닐) (CPVC) Plastic Pipe and Fittings

21-57) ASTM F628 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, 낭비, and Vent Pipe With a Cellular Core

21-58) ASTM F628 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, 낭비, and Vent Pipe With a Cellular Core

21-59) ASTM F656 – 08 ; Standard Specification for Primers for Use in Solvent Cement Joints of Poly(염화 비닐) (PVC) Plastic Pipe and Fittings

21-60) ASTM F891 – 09 ; Standard Specification for Coextruded Poly(염화 비닐) (PVC) Plastic Pipe With a Cellular Core

21-61) BDS 1111:1984 ; Centrifugally Cast (spun) Iron Pressure Pipes for Water, Gas and Sewage;

21-62) BDS 1162 : 2006 (1st revision) ; Ceramic wash basin and pedestal, ceramic wash basin and pedestals dimension, design & 구성, type, permissible deviation

21-63) BDS 1163 : 1987 ; Specification for Vitreous Sanitary Appliances,

21-64) BDS 1356:1992 ; Specification for Ferrules for Water Services;

21-65) BDS 1357: 1992 ; Specification for Washers with Fittings for Water Service;

21-66) BDS 1361 : 1992 ; Faucets

21-67) BDS 1361:1992 ; Faucets

21-68) BDS 1507 : 1995 ; Bib taps used in water supply

21-69) BDS 1508 : 1995 ; Stop taps used in water supply.Specifies the requirements, dimensions construction, materials and test methods of stop taps used in water supply.

21-70) BDS 1508:1995 ; Stop taps used in water supply.

21-71) BDS 1509:1995 ; Pillar taps used in water supply

21-72) BDS 1562:1997 ; Solvent cements for polyvinyl chloride (PVC) plastic pipe and fitting.

21-73) BDS 1593 : 1998 ; Plastic sanitary squatting pan

21-74) BDS 1593:1998 ; Plastic sanitary squatting pan

21-75) BDS 428:1964 ; Specification for Asbestos Cement Pressure Pipe;

21-76) BDS 429:1964 ; Specification for Asbestos Cement Building and Sanitary Pipes (under revision);

21-77) BDS 987 : 1981 ; Sand cast brass screw‐down bib taps and stop taps for water services.

21-78) BDS EN 1112: 2009 ; Sanitary tapware ‐ Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 – General technical specification

21-79) BDS EN 1113: 2009 ; Sanitary tapware – Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 – General technical specification

21-80) BDS EN 1254‐2: 2009 ; Copper and copper alloys ‐ Plumbing fittings – Part 2: 압축 피팅 구리 튜브에 사용 종료

21-81) BDS EN 14506: 2009 ; Devices to prevent pollution by backflow of potable water – Automatic diverter – Family H, type C

21-82) BDS EN 1717: 2009 ; Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow

21-83) BDS EN 200: 2009 ; Sanitary tapware — Single taps and combination taps for water supply systems of type 1 and type 2 — General technical specification

21-84) BDS EN 246: 2009 ; Sanitary tapware – General specifications for flow rate regulators

21-85) BDS EN 248: 2009 ; Sanitary tapware – General specification for electrodeposited coatings of Ni‐Cr

21-86) BDS EN 681-1: 2008 ; Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: 가황 고무

21-87) BDS EN 681-2 : 2008 ; Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: 열가소성 엘라스토머

21-88) BDS ISO /TR 4191: 2008 ; Unplasticized polyvinyl chloride (PVC-U) pipes for water supply-Recommended practice for laying

21-89) BDS ISO 11413:2010 ; Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting BDS ISO 11414, Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

21-90) BDS ISO 1167-1 : 2008 ; Thermoplastics pipes fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure- Part 1: General method

21-91) BDS ISO 1167-2 : 2008 ; Thermoplastics pipes fittings and assemblies for the conveyance of fluids- Determination of the resistance to internal pressure-

21-92) BDS ISO 12176-2:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion

21-93) BDS ISO 12176-3:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 3: Operator’s badge

21-94) BDS ISO 12176-4:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4: Traceability coding

21-95) BDS ISO 13479:2010 ; Polyolefin pipes for the conveyance of fluids — Determination of

21-96) BDS ISO 13761:2010 ; Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 ° C

21-97) BDS ISO 13951:2010 ; Plastics piping systems — Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading

21-98) BDS ISO 13953:2010 ; Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint

21-99) BDS ISO 13954:2010 ; Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

21-100) BDS ISO 13955:2010 ; Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies

21-101) BDS ISO 13957:2010 ; Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance

21-102) BDS ISO 14236:2010 ; Plastics pipes and fittings — Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems

21-103) BDS ISO 161-1 : 2008 ; Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and Nominal Pressures- Part 1: Metric series

21-104) BDS ISO 161-2 : 2008 ; Thermoplastics pipes for the conveyance of fluids- Nominal outside diameters and Nominal Pressures- Part 2: Inch – based series

21-105) BDS ISO 1746 : 2008 ; Rubber or Plastics hoses and tubing-Bending tests

21-106) BDS ISO 18553:2010 ; Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds

21-107) BDS ISO 18553:2010 ; Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds Amendment 1:2010

21-108) BDS ISO 2505 : 2008 ; Thermoplastics pipes- Longitudinal reversion – Test method and parameters

21-109) BDS ISO 2507-2 : 2008 ; Thermoplastics pipes and fittings – Vicat softening temperature- Part 2: Test conditions for Unplasticized poly (Vinyl chloride) (PVC-U) or chlorinated poly (Vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (Vinyl chloride) (PVC-HI) 파이프

21-110) BDS ISO 265-1 : 2008 ; Pipes and fittings of plastics materials- fittings for domestic and industrial waste pipes- Basic dimensions: Metric series- Part 1: Unplasticized Poly (Vinyl chloride) (PVC-U)

21-111) BDS ISO 3114: 2008 ; Unplasticized polyvinyl chloride (PVC) pipes for potable water supply-Extractability of lead and tin- Test method

21-112) BDS ISO 3126 : 2008 ; Plastics piping systems-Plastics components- Determination of dimensions

21-113) BDS ISO 3127: 2008 ; Thermoplastics pipes- Determination of resistance to external blows-Round – the – clock method

21-114) BDS ISO 3419: 2008 ; Non – alloy and alloy steel butt–welding fittings

21-115) BDS ISO 3458:2010 ; Assembled joints between fittings and polyethylene (PE)

21-116) BDS ISO 3459:2010 ; Polyethylene (PE) pressure pipes — Joints assembled with mechanical fittings — Internal under pressure test method and requirement

21-117) BDS ISO 3501:2010 ; Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of resistance to pull-out

21-118) BDS ISO 3503:2010 ; Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of leakproofness under internal pressure when subjected to bending

21-119) BDS ISO 3633: 2008 ; Plastics piping systems for soil and waste discharge (Low and high temperature ) inside buildings- Specifications

21-120) BDS ISO 3822-‐1: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 1: Method of measurement

21-121) BDS ISO 3822-‐2: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 2: Mounting and operating conditions for draw‐off taps and mixing valves

21-122) BDS ISO 3822-‐4: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 4: Mounting and operating conditions for special appliances

21-123) BDS ISO 4065: 2008 ; Thermoplastics pipes- Universal wall thickness table

21-124) BDS ISO 4422-1: 2008 ; Pipes and fittings made of unplasticized poly (비닐 클로라이드) (PVC-U) for water supply – Specifications – Part 1: General

21-125) BDS ISO 4422-2: 2008 ; Pipes and fittings made of unplasticized poly (비닐 클로라이드) (PVC-U) for water supply – Specifications – Part 2: Pipes (with or without integral sockets)

21-126) BDS ISO 4422-3: 2008 ; Pipes and fittings made of unplasticized poly (비닐 클로라이드)(PVC-U) for water supply- Specifications – Part 3: Fittings and joints

21-127) BDS ISO 4422-4: 2008 ; Pipes and fittings made of unplasticized poly (비닐 클로라이드) (PVC-U) for water supply- Specifications- Part 4: Valves and ancillary equipment

21-128) BDS ISO 4422-5: 2008 ; Pipes and fittings made of unplasticized poly (비닐 클로라이드) (PVC- U) for water supply- Specifications- Part 5: Fitness for purpose of the system

21-129) BDS ISO 4427-1:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General

21-130) BDS ISO 4427-1:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General Technical corrigendum 1: 2010

21-131) BDS ISO 4427-2:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes

21-132) BDS ISO 4427-3:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: 피팅

21-133) BDS ISO 4427-5:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system

21-134) BDS ISO 4433-3: 2008 ; Thermoplastics pipes- Resistance to liquid chemicals- Classification-Part 3: Unplasticized poly (비닐 클로라이드) (PVC-U), high- impact poly (비닐 클로라이드) (PVC-HI) and chlorinated poly (비닐 클로라이드) (PVC –C) 파이프

21-135) BDS ISO 4435: 2008 ; Plastic piping systems for non- pressure underground drainage and sewerage- Unplasticized poly (비닐 클로라이드) (PVC-U)

21-136) BDS ISO 4439: 2008 ; Unplasticized polyvinyl chloride (PVC) pipes and fittings – Determination and specification of density

21-137) BDS ISO 5251: 2008 ; Stainless steel butt–welding fittings

21-138) BDS ISO 6259-1: 2008 ; Thermoplastics pipes- Determination of tensile properties- Part 1: General test method

21-139) BDS ISO 6259-2: 2008 ; Thermoplastics pipes- Determination of tensile properties- Part 2: Pipes made of unplasticized poly (비닐 클로라이드) (PVC-U), Chlorinated poly (비닐 클로라이드) (PVC-C), and high – impact poly (비닐 클로라이드) (PVC-HI)

21-140) BDS ISO 6761: 2008 ; Steel tubes – Preparation of ends of tubes and fittings for welding

21-141) BDS ISO 6964:2010 ; Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method and basic specification

21-142) BDS ISO 6992: 2008 ; Unplasticized polyvinyl chloride (PVC-U) pipes for drinking water supply – Extractability of cadmium and mercury occurring as impurities

21-143) BDS ISO 9624:2010 ; Thermoplastics pipes for fluids under pressure — Mating dimensions of flange adapters and loose backing flanges

21-144) BS 1010 ; Specification for Draw-Off Taps and Stopvalves for Water Services;

21-145) BS 1125: 1987 ; Specification for WC Flushing Cisterns (Including Dual Flash Cisterns and Flush Pipes);

21-146) BS 1212 3 (Parts) ; Specification for Float Operated Valves (excluding floats);

21-147) BS 1244 ; Metal Sink for Domestic Purposes;

21-148) BS 1254:1981 ; Specification for C Seats (Plastics);

21-149) BS 1329:1974 ; Specification for Metal Hand Rinse Basins;

21-150) BS 1415 ( 2 parts) ; Mixing Valves (Manullay Operated);

21-151) BS 1876: 1992(1977) ; Specification for Automatic Flushing Cistern for Urinals

21-152) BS 1968 ; Specification for Floats for Ball Valves (copper);

21-153) BS 2456: 1973 ; Specification for Floats for Ball Valves (plastic) for Cold and Hot Water

21-154) BS 3377:1985 ; Specification for Boilers for Use with Domestic Solid Mineral Fuel Appliances;

21-155) BS 5163: 1986 ; Specification for Predominantly Key-Operated Cast Iron Wedge Gate Valve for Water Works;

21-156) BS 5433: 1976 ; Specification for Underground Stop valves for Water Services (copper);

21-157) BS 843: 1976 ; Specification for Thermal Storage Electric Water Heaters;

21-158) BS 855:1976 ; Specification for Welded Steel Boilers for Central Heating and Indirect Hot Water Supply.

21-159) IS 404 (Part-I)-1993 ; Specification for Lead Pipes Part I for other than Chemical Purpose (third Revision);

21-160) ISO 160: 1980 ; Asbestos-Cement Pressure Pipes and Joints;

21-161) ISO 2531-1991 ; Ductile Iron Pipes, Fittings and Accessories for Pressure Pipelines;

21-162) ISO 392:1986 ; Asbestos-Cement Pipe Fittings for Building and Sanitary Purposes;

21-163) ISO 881:1980 ; Asbestos-Cement Pipes, Joints and Fittings for Sewerage and Drainage;

20. PAINTS AND VARNISHES

20-1) BDS 1005:1981 ; Specification for Ready Mixed Paint, Brushing, Finishing, Stoving, Enamel, Colour as Required;

20-2) BDS 1064:1983 ; Specification for Varnish, Stoving;

20-3) BDS 1065:1983 ; Specification for Varnish, Acid Resisting;

20-4) BDS 1066:1983 ; Specification for Varnish, Finishing, Interior;

20-5) BDS 1097:1984 ; Specification for Plastic Emulsion Paint.

20-6) BDS 1141:1986 ; Specification for Ready Mixed Aluminium Priming Paints for Woodwork;

20-7) BDS 1151:1986 ; Specification for Pavement Marking Paints.

20-8) BDS 13:1960 ; Specification for Ready Mixed Paints, Varnish, Lacquers and Related Products (under revision);

20-9) BDS 14:1960 ; Specification for Black Bituminous Paint, Brushing for General Purposes (under revision);

20-10) BDS 397:1964 ; Specification for Ready Mixed Paint, Brushing, Red Oxide Zinc Chrome, Priming (under revision);

20-11) BDS 398:1964 ; Specification for Ready Mixed Paint, Spraying, Red Oxide Zinc Chrome, Priming (under revision);

20-12) BDS 399:1964 ; Specification for Aluminum Paint, Spraying for General Purposes, in Dual Container (under revision);

20-13) BDS 400:1964 ; Specification for Aluminium Paint, Brushing, for General Purposes in Dual Container (under revision);

20-14) BDS 401:1964 ; Specification for Varnish, Finishing, Exterior, Type-I, (Synthetic) (Tentative) (under revision);

20-15) BDS 401:1964 ; Specification for Varnish, Finishing, Exterior, Type-I, (synthetic) (under revision);

20-16) BDS 402:1989 ; Specification for Ready Mixed Paint, Brushing, Finishing, Semigloss, for General Purposes (First Revision);

20-17) BDS 499:1965 ; Specification for Ready Mixed Paints, Brushing, for Road Marking (white, yellow and black) (under revision);

20-18) BDS 500:1965 ; Specification for Distemper Dry (under revision);

20-19) BDS 616:1966 ; Specification for Enamel, Brushing, Exterior (나는) Undercoating, (ii) Finishing, Colour as Required (under revision);

20-20) BDS 617:1966 ; Specification for Enamel, Brushing, Interior (나는) Undercoating, (ii) Finishing, Colour as Required (under revision);

20-21) BDS 926:1980 ; Specification for Ready Mixed Paint, Brushing, Petrol Resisting, Air Drying, for Exterior Painting of Containers, Colour as Required;

20-22) BDS 927:1980 ; Specification for Ready Mixed Paint, Brushing, Petrol Resisting, Air Drying, for Interior Painting of Tanks and Containers, Red Oxide (colour unspecified);

20-23) BDS 928:1980 ; Specification for Ready Mixed Paint, Brushing, Acid Resisting, for Protection Against Acid Fumes, Colour as Required;

20-24) BDS 973:1981 ; Specification for Specification and Methods of Test for Linseed Stand Oil for Paints and Varnishes;

20-25) BDS 974:1981 ; Specification and Methods of Test for Raw Tung Oils for Paints and Varnishes;

20-26) IS 101 ; Methods of sampling and test for paints, varnishes and related products:

20-27) IS 104:1979 ; Specification for ready mixed paint, brushing, zinc chrome, priming (second revision)

20-28) IS 109:1968 ; Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 과 631 (first revision)

20-29) IS 11883:1986 ; Specification for ready mixed paint, brushing, red oxide, priming for metals

20-30) IS 123:1962 ; Specification for ready mixed paint, brushing, finishing, semi-gloss, for general purposes, to Indian Standard colours No. 445, 446, 448, 449, 451 과 473; and red oxide (colour unspecified) (revised)

20-31) IS 13183:1991 ; Specification for aluminium paints, heat resistant

20-32) IS 13213:1991 ; Specification for polyurethane full gloss enamel (two pack)

20-33) IS 133:1993 ; Specification for enamel, interior (a) undercoating, (B) finishing (third revision)

20-34) IS 13607:1992 ; Specification for ready mixed paint, finishing, general purposes, synthetic

20-35) IS 137:1965 ; Specification for ready mixed paint, brushing, matt or egg-shell flat, finishing, interior, to Indian Standard colour, as required (revised)

20-36) IS 13871:1993 ; Specification for powder coatings

20-37) IS 14314:1995 ; Specification for thinner general purposes for synthetic paints and varnishes

20-38) IS 158:1981 ; Specification for ready mixed paint, brushing, bituminous, black, lead-free, acid, alkali, and heat resisting (third revision)

20-39) IS 168:1993 ; Specification for ready mixed paint, air-drying semi-glossy/matt, for general purposes (third revision)

20-40) IS 2074:1992 ; Specification for ready mixed paint, air drying red oxide-zinc chrome, priming (second revision)

20-41) IS 2075:2000 ; Specification for ready mixed paint, stoving, red oxide-zinc chrome, priming (second revision)

20-42) IS 2339:1963 ; Specification for aluminium paint for general purposes, in dual container

20-43) IS 2932:2003 ; Specification for enamel, synthetic, exterior, (a) undercoating, (B) finishing (third revision)

20-44) IS 2933:1975 ; Specification for enamel, exterior, (a) undercoating, (B) finishing (first revision)

20-45) IS 324:1959 ; Specification for ordinary denatured spirit (revised)

20-46) IS 324-1959 ; Specification for Ordinary Denatured Spirit (revised);

20-47) IS 337:1975 ; Specification for varnish, finishing, interior (first revision)

20-48) IS 341:1973 ; Specification for black Japan, Types A, B and C first revision)

20-49) IS 347-1975 ; Specification for Varnish, Shellac for general purposes (First Revision);

20-50) IS 348-1968 ; Specification for French Polish (First Revision);

20-51) IS 3536:1999 ; Specification for ready mixed ‘paint, brushing, wood primer

20-52) IS 3537:1966 ; Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275:”281, 352, 353, 358 에 361, 363,364,388,410,442, 444,628, 631,632,634,693,697, white andblack

20-53) IS 3539:1966 ; Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required

20-54) IS 3585:1966 ; Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work

20-55) IS 3678:1966 ; Specification for ready mixed paint, thick white, for lettering

20-56) IS 427:1965 ; Specification for distemper, dry, colour as required (revised)

20-57) IS 428:2000 ; Specification for distemper, washable (second revision)

20-58) IS 524:1983 ; Specification for varnish, finishing, exterior, synthetic (second revision)

20-59) IS 525:196 ; Specification for varnish, finishing, exterior and general purposes (first revision)

20-60) IS 533:1998 ; Specification for gum spirit of turpentine (oil of turpentine) (second revision)

20-61) IS 5410:1992 ; Specification for cement paint, colour as required (first revision)

20-62) IS 5411 ; Specification for plastic emulsion paint:

20-63) IS 642:1963 ; Specification for varnish medium for aluminium paint (revised)

20-64) IS 82:1992 ; Methods of sampling and test for thinners and solvents for paints (first revision)

20-65) IS 8662:1993 ; Specification for enamel, synthetic, exterior, (a) undercoating, (B) finishing, for railway coaches (first revision)

20-66) IS 9862:1981 ; Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting

19. ROOF COVERINGS

19-1) ASTM A755 / A755M – 03(2008) ; 강판에 대한 표준 규격, Metallic Coated by the Hot-Dip Process and Pre-painted by the Coil-Coating Process for Exterior Exposed Building Products

19-2) ASTM B101 – 07 ; Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction

19-3) ASTM C1029 – 09 ; Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

19-4) ASTM C222 – 97(2008) ; Standard Specification for Asbestos-Cement Roofing Shingles

19-5) ASTM C406 – 06e1 ; Standard Specification for Roofing Slate

19-6) ASTM C836 / C836M – 10 ; Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

19-7) ASTM D1227 – 95(2007) ; Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

19-8) ASTM D1863 – 05 ; Standard Specification for Mineral Aggregate Used on Built-Up Roofs

19-9) ASTM D2178 – 04 ; Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

19-10) ASTM D225 – 07 ; Standard Specification for Asphalt Shingles (Organic Felt) Surfaced With Mineral Granules

19-11) ASTM D226 / D226M – 09 ; Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

19-12) ASTM D227 – 03 ; Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

19-13) ASTM D2626 – 04 ; Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

19-14) ASTM D2898 – 10 ; Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

19-15) ASTM D312 – 00(2006) ; Standard Specification for Asphalt Used in Roofing

19-16) ASTM D3161 – 09 ; Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

19-17) ASTM D3747 – 79(2007) ; Standard Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

19-18) ASTM D3909 – 97B(2004)e1 ; Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced With Mineral Granules

19-19) ASTM D4272 – 09 ; Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop

19-20) ASTM D4434 / D4434M – 09 ; Standard Specification for Poly(염화 비닐) Sheet Roofing

19-21) ASTM D450 – 07 ; Standard Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing

19-22) ASTM D4601 – 04 ; Standard Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing

19-23) ASTM D4637 – 08 ; Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane

19-24) ASTM D4897 / D4897M – 01(2009) ; Standard Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing

19-25) ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

19-26) ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

19-27) ASTM E108 – 10a ; Standard Test Methods for Fire Tests of Roof Coverings

19-28) ASTM G154 – 06 ; Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

19-29) ASTM G155 – 05a ; Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

19-30) ASTM G90 – 05 ; Standard Practice for Performing Accelerated Outdoor Weathering of Nonmetallic Materials Using Concentrated Natural Sunlight

19-31) BDS 1046:1983 ; Specification for Asbestos Cement Products – Corrugated Sheets and Fittings for Roofing and Cladding;

19-32) BDS 1122:1985 ; Specification for Hot-dip Galvanized Steel and Coil.

19-33) BDS 430:1964 ; Specification for Asbestos Cement Corrugated Sheets for Roofing and Cladding

19-34) BDS 431:1964 ; Specification for Asymmetrical Section Corrugated Sheets in Asbestos Cement for Roofing and Cladding

19-35) BDS 579:1966 ; Specification for Asbestos Cement Flat Sheets (under revision);

19-36) BDS 868:1978 ; Code of Practice for Galvanized Corrugated Sheet Roof and Wall Coverings;

19-37) BDS EN 1024: 2008 ; Clay roofing tiles for discontinuous laying — Determination of geometric characteristics

19-38) BDS EN 1304: 2008 ; Clay roofing tiles and fittings — Product definitions and specifications

19-39) BDS EN 490: 2008 ; Concrete roofing tiles and fittings for roof covering and all cladding — Product specifications

19-40) BDS EN 49l: 2008 ; Concrete roofing tiles and fittings for roof covering and wall cladding — Test methods

19-41) BDS EN 538: 2008 ; Clay roofing tiles for discontinuous laying — Flexural strength test

19-42) BDS EN 539-l: 2008 ; Clay roofing tiles for discontinuous laying Determination of physical characteristics — Part 1: Impermeability test

18. BUILDERS HARDWARE

18-1) BDS 113:1986 ; Specification for Latches and Locks for Doors in Buildings;

18-2) IS 10019-1981 ; Specification for Steel Window Stays and Fasteners;

18-3) IS 10090-1982 ; Specification for Numericals;

18-4) IS 1019-1974 ; Specification for Rim Latches (Second Revision);

18-5) IS 10342-1982 ; Specification for Curtain Rail System

18-6) IS 12817:1997 ; Specification for stainless steel butt hinges (first revision)

18-7) IS 12867:1989 ; Specification for PVC hand rails covers

18-8) IS 1341-1992 ; Specification for Steel Butt Hinges (Sixth Revision);

18-9) IS 14912:2001 ; Specification for door closers concealed type (hydraulically regulated)

18-10) IS 1823-1980 ; Specification for Floor Door Stoppers (Third Revision);

18-11) IS 1837-1966 ; Specification for Fanlight Pivots (First Revision);

18-12) IS 204-1991/1992 ; Specification for Tower Bolts;

18-13) IS 205-1992 ; Specification for Nonferrous Metal Butt Hinges (fourth Revision);

18-14) IS 206-1992 ; Specification for Tee and Strap Hinges (Fourth Revision);

18-15) IS 208-1996 ; Specification for Door Handles (Fifth Revision);

18-16) IS 2209-1976 ; Specification for Mortice Locks (vertical type) (Third Revision);

18-17) IS 2681-1993 ; Specification for Nonferrous Metal Sliding Door Bolts for Use with Padlocks (Third Revision);

18-18) IS 281-1991 ; Specification for Mild Steel Sliding Door Bolts for Use with Padlock (Third Revision);

18-19) IS 3564-1995 ; Specification for Door Closers (hydraulically regulated) (Second Revision);

18-20) IS 362-1991 ; Specification for Parliament Hinges (Fifth Revision);

18-21) IS 363-1993 ; Specification for Hasps and Staples (Fourth Revision);

18-22) IS 364-1993 ; Specification for Fanlight Catch (Third Revision);

18-23) IS 3818-1992 ; Specification for Continuous (piano) Hinges (Third Revision);

18-24) IS 3828-1966 ; Specification for Ventilator Chains;

18-25) IS 3843-1995 ; Specification for Steel Backflap Hinges; (First Revision)

18-26) IS 3847-1992 ; Specification for Mortice Night Latches; (First Revision)

18-27) IS 452-1973 ; Specification for Door Springs, Rat-tail Type (Second Revision);

18-28) IS 453-1993 ; Specification for Double Acting Spring Hinges (Third Revision);

18-29) IS 4621-1975 ; Specification for Indicating Bolts for use in Public Baths and Lavatories (First Revision);

18-30) IS 4948-2002 ; Specification for Welded Steel Wire Fabric for General Use (Second Revision);

18-31) IS 4992-1975 ; Specification for Door Handles for Mortice Locks (vertical type) (First Revision);

18-32) IS 5187-1972 ; Specification for Flush Bolts (First Revision);

18-33) IS 5899-1970 ; Specification for Bathroom Latches;

18-34) IS 5930-1970 ; Specification for Mortice Latch (vertical type);

18-35) IS 6315-1971 ; Specification for Floor Springs (hydraulically regulated) for Heavy Doors;

18-36) IS 6318-1971 ; Specification for Plastic Window Stays and Fasteners;

18-37) IS 6343-1982 ; Specification for Door Closers (pneumatically regulated) for Light Doors Weighing up to 40 kg (First Revision);

18-38) IS 6602-1972 ; Specification for Ventilator Poles;

18-39) IS 6607-1972 ; Specification for Rebated Mortice Locks (vertical type);

18-40) IS 7196-1974 ; Specification for Hold Fast;

18-41) IS 7197-1974 ; Specification for Double Action Floor Springs (without oil check) for Heavy Doors;

18-42) IS 729-1979 ; Specification for Drawer Locks, Cupboard Locks and Box Locks (Third Revision);

18-43) IS 7534-1985 ; Specification for sliding locking bolts for use with padlocks (first revision);

18-44) IS 7540-1974 ; Specification for Mortice Dead Locks;

18-45) IS 8756-1978 ; Specification for Ball Catches for use in Wooden Almirah;

18-46) IS 8760-1978 ; Specification for Mortice Sliding Door Locks, with Lever Mechanism;

18-47) IS 9106-1979 ; Specification for Rising Butt Hinges;

18-48) IS 9131-1979 ; Specification for Rim Locks;

18-49) IS 9460-1980 ; Specification Flush Drop Handle for Drawer;

18-50) IS 9899-1981 ; Specification for Hat, Coat and Wardrobe Hooks;

17. ALUMINIUM AND ALUMINIUM ALLOYS

17-1) ASTM B108 / B108M – 08 ; Standard Specification for Aluminum-Alloy Permanent Mold Castings

17-2) ASTM B209 – 07 ; Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

17-3) ASTM B210 – 04 ; Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

17-4) ASTM B211 – 03 ; Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire

17-5) ASTM B221 – 08 ; Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

17-6) ASTM B241 / B241M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

17-7) ASTM B26 / B26M – 09 ; Standard Specification for Aluminum-Alloy Sand Castings

17-8) ASTM B308 / B308M – 02 ; Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles

17-9) ASTM B313 / B313M – 09 ; Standard Specification for Aluminum and Aluminum-Alloy Round Welded Tubes

17-10) ASTM B316 / B316M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods

17-11) ASTM B429 / B429M – 06 ; Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube

17-12) ASTM B483 / B483M – 03 ; Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applications

17-13) ASTM B547 / B547M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round Tube

17-14) ASTM B632 / B632M – 08 ; Standard Specification for Aluminum-Alloy Rolled Tread Plate

17-15) ASTM B745 / B745M – 97(2005) ; Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

17-16) ASTM B85 / B85M – 09 ; Standard Specification for Aluminum-Alloy Die Castings

17-17) ASTM E34 – 94(2002) ; Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys

17-18) BDS EN 12020-1:2010 ; Aluminium and aluminium alloys— Extruded precision profiles in alloys EN AW-6060 and EN AW-6063— Part 1: 검사 및 전달을위한 기술적 조건

17-19) BDS EN 12020-2:2010 ; Aluminium and aluminium alloys — Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 — Part 2: 크기와 형태의 허용차

17-20) BDS EN 515:2010 ; Aluminium and aluminium alloys — Wrought products — Temper designations

17-21) BDS EN 755-1:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 1: 검사 및 전달을위한 기술적 조건

17-22) BDS EN 755-2:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: 기계적 성질

17-23) BDS EN 755-3:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 3: Round bars, tolerances on dimensions and form

17-24) BDS EN 755-4:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 4: Square bars, tolerances on dimensions and form

17-25) BDS EN 755-5:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 5: Rectangular bars, tolerances on dimensions and form

17-26) BDS EN 755-6:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 6: Hexagonal bars, tolerances on dimensions and

17-27) BDS EN 755-7:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 7: Seamless tubes, tolerances on dimensions and form

17-28) BDS EN 755-8:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 8: Porthole tubes, tolerances on dimensions and form

17-29) BDS EN 755-9:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 9: Profiles, tolerances on dimensions and form

16. DOORS, WINDOWS AND VENTILATORS

16-1) BDS 1270: 1990 ; Specification for Strong Room Door;

16-2) BDS 1273: 1990 ; Specification for Vault Doors;

16-3) BDS 142:1961 ; Specification for Wood Door (under revision);

16-4) BDS 1504:1996 ; Timber door window and ventilator frames

16-5) BDS 173:1962 ; Specification for Wood Windows (under revision);

16-6) BDS 820:1978 ; Recommendation for Maximum Permissible Moisture Content of Timber Used for Different Purposes in Bangladesh;

16-7) BDS EN 12608: 2008 ; 경질 폴리 염화 비닐 (PVC – U) profiles for the fabrication of windows and doors — Classification, 요구 사항과 시험 방법

16-8) BDS EN 477: 2008 ; 경질 폴리 염화 비닐 (PVC – U) profiles for the fabrication of windows and doors — Determination of the resistance to impact of main profiles by falling mass

16-9) BDS EN 478: 2008 ; 경질 폴리 염화 비닐 (PVC – U) profiles for the fabrication of windows and doors — Determination of appearance after exposure at 150 ºC

16-10) BDS EN 479: 2008 ; 경질 폴리 염화 비닐 (PVC – U) profiles for the fabrication of windows and doors — Determination of heat reversion

16-11) BDS EN 513: 2008 ; 경질 폴리 염화 비닐 (PVC – U) profiles for the fabrication of windows and doors — Determination of the resistance to artificial weathering

16-12) BDS EN 514: 2008 ; 경질 폴리 염화 비닐 (PVC – U) profiles for the fabrication of windows and doors — Determination of the

16-13) BDS ISO 1163-1:2008 ; Plastics — Unplasticized poly (비닐 클로라이드) (PVC – U) moulding and extrusion materials — Part 1: Designation system and basis for specifications

16-14) BDS ISO 1163-2:2008 ; Plastics — Unplasticized poly (비닐 클로라이드) (PVC – U) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties

16-15) IS 1003-2003/1994 ; Specification for Timber Panelled and Glazed Shutters;

16-16) IS 1038-1983 ; Specification for Steel Doors, Windows and Ventilators (Third Revision);

16-17) IS 10451-1983 ; Specification for Steel Sliding Shutters (top hung type);

16-18) IS 10521-1983 ; Specification for Collapsible Gates;

16-19) IS 1361-1978 ; Specification for Steel Windows for Industrial Buildings (First Revision);

16-20) IS 14856:2000 ; Specification for glass fibre reinforced (GRP) panel type door shutters for internal use

16-21) IS 15380:2003 ; Specification for moulded raised high density fibre (HDF) panel doors

16-22) IS 1826-1961 ; Specification for Venetian Blinds for Windows;

16-23) IS 1948-1961 ; Specification for Aluminium Doors, Windows and Ventilators;

16-24) IS 1949-1961 ; Specification for Aluminium Windows for Industrial Buildings;

16-25) IS 2191-1983 ; Specification for Wooden Flush Door Shutters (cellular and hollow core type);

16-26) IS 2202-1991/83 ; Specification for Wooden Flush Door Shutters (solid core type);

16-27) IS 4020-1998 ; Method of tests for door shutters:

16-28) IS 4021:1995 ; Specification for timber door, window and ventilator frames

16-29) IS 4351-2003 ; Specification for Steel Door Frames (Second Revision);

16-30) IS 4962:1968 ; Specification for wooden side sliding doors

16-31) IS 6198:1992 ; Specification for ledged, braced and battened timber shutters (second revision)Revision);

16-32) IS 6248-1979 ; Specification for Metal Rolling Shutters and Rolling Grills (First Revision);

16-33) IS 7452-1990 ; Specification for Hot Rolled Steel Sections for Doors, Windows and Ventilators (Second Revision);