Archive for month: December, 2013

러시아 수출 인증서 비용 절감 대책

28 Dec 2013 Comments
Off


GOST-R 인증서 할인 EVENT !

 

            GOST-R, GOST-TR, CU-TR, RTN 등

                      유효기간  만기 전으로

                                최소 기간이 남아 있는 인증서는

                                            최대  50% 할인된 비용으로

                                            인증서를 재발급 합니다.

 

E-Mail : anycerti@gmail.com

Tel : 02-980-9800(대표전화)  

 

러시아 인증서 조회 방법 안내

26 Dec 2013 Comments
Off

GOST인증 조회작성 안내

GOST Searching



조회 사례 : 조회사례 바로가기


CU-TR인증 조회작성 안내

CU-TR 조회방법




ASTM E 84 시험안내

24 Dec 2013 Comments
Off

연소특성시험
ASTM E 84 – Surface Burning Characteristics-Fire safety technology
표면연소 특성이란?

재료의 표면연소 특성은 연기생성을 제한하고 동시에 화염에 저항하는 능력을 종합적으로 평가하는 것으로써 보통 건축법이나 기타 정부등의 기관에서 규정한다.

내부 벽이나 천장 마감 재료로 사용되는 재료에 있어서 화염 전파율은 중요한 물리적 특성 중에 하나이다.

통제된 화재 조건에서 상대적으로 표면 연소 특성을 결정하기위한 표준적인 시험방법은 수평 화재 터널 장치(Steiner Tunnel)를 이용하는 ASTM E 84이다. 이 방법은 비록 두 측정이 직접적 연관이 적을 수 있지만, 화염의 확산 및 연기의 확산 지수를 결정하고, 특정설치요구사항에 대한 재료의 적용성을 결정하는데 도움이된다.

 

시험 방법

ASTM E 84 ; 건축 자재의 표면연소 특성에 대한 시험표준 방법에 지정된 스타이너 터널은 특정한 시험 조건하에서 물질의 상대적 표면연소 특성을 결정하기 위해서 설계되었습니다. 시험의 결과는 화염확산 지수( FSI )와 연기발생(SD) 지수로 표현됩니다.

이 스타이너 터널은 규정된 특정한 온도로 예비 가열하고 또 사전시험온도로 냉각이 허용되며 12인치 폭과 24피트 길이의 터널뚜껑을 열고 시료를 설치할 수 있도록 되어 있다. 터널 천정에 설치되는 시험편은 장치의바닥을 향해 설치된다. 뚜껑이 덮여지고 버너를 점화하여 시편의 한쪽에서 불꽃을 인가한다. 화염확산 거리를 관찰하고 10분 이상동안 매초마다 확산거리를 기록하고 레드 오크(임의로 할당된 100에 대한 FSI 및 SD )의 비교치에 근거한 FSI 및 SD 를 결정하기 위하여 계산이 이루어진다 .

 

테스트 결과

ASTM E 84에는 등급기준이 포함되어 있지 않습니다. 그러나, 많은 업계 문서는 ASTM E 84 테스트 데이터를 참조 하고 일반적 등급기준을 적용합니다. 비록 각 문서에서 사용되는 용어가 서로 다를 수 있지만 등급범위는 일반적으로 동일하다.

 

일반적인 범위 :

클래스 A 또는 클래스 1 ( FSI = 0-25 )
클래스 B 또는 클래스 2 ( FSI = 26-75 )
클래스 C 또는 클래스 3 ( FSI = 76-200 )
위 모든 각 분류는 최대 450의 연기발생(SD )율을 규정함

 

Test Result (Red Oak Referenced)

아래는 ASTM E84 시험결과표현 방법사례입니다.

Flame Spread Index

Smoke Developed

테스트 실시 시기

ASTM E 84는 제품 개발 단계나 지속적인 기업 품질 보증 프로그램의 일부로 이용 될 수있다. 특히 북미와 중동의 많은 글로벌 관할권역의 건물관리는 내부 벽 및 천정 마감 재료에 대해 ASTM E 84를 강제하고 있고 나아가 지역별 기관의 강제요건에 따라 이들 재료에 대한 일회시험 반복시험, 확장시험(예 :30 분), 또는 더 집중적인 제품 인증 프로그램의 시험항목을 적용한 시험의 결과가 적용되어질 수 있다 .

 

시료 요구 사항

각 시험에서는 폭 21인치(533mm), 길이24피트(7,315mm)의 시료가 요구된다 (예:각 21인치 폭(533mm), 8 피트 길이(2,438mm)의 시료 3개가 필요). 시료의 두께가 3 인치(75mm) 미만 또는 6 인치 (150mm )보다 두꺼운 경우, 터널 뚜껑을 수정해야 표준시험을 할 수 있으며 유리 섬유 강화 시멘트 보드 또는 석고 보드가 일반적인 기판으로 사용되어 질 수 있다. 그 외 세부 내용은 시험소의 설비의 조건을 고려하여야 한다.

 

TEST PROCEDURE

ASTM E 84-13a
-”Standard Method of Test for Surface Burning Characteristics of Building Materials”

ASTM E 84-13a “건축 자재의 표면 연소 특성에 대한 표준 시험 방법”으로 지정된이 방법은 특정 시험 조건 하에서 재료의 상대적인 표면 연소 특성을 결정하도록 작성되었습니다. 시험의 결과는 화염 확산 지수 (FSI) 및 연기 발생 (SD)으로 표현되며  화염 데이터의 비교 표면 확산을 개발하기 위해 건축에 사용되는 재료, 제품 및 조립품에 이 시험방법이 적용 가능하지만, 시험 결과는 모든 건축 화재 조건에서 시험 된 물질의 상대적인 표면 연소 특성을 반영하지 않을 수 있습니다. 따라서 시험대상 및 시험목적 등을 고려한 시험조건을 검토하여야 합니다.

 

화재관련 규격 및 시험

ASTM & STP

  1. ASTM D2898-10 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
  2. ASTM D5425-13 Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products
  3. ASTM D5664-10 Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber
  4. ASTM D6113-11 Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
  5. ASTM D6513-08 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
  6. ASTM E108-11 Standard Test Methods for Fire Tests of Roof Coverings
  7. ASTM E119-12a Standard Test Methods for Fire Tests of Building Construction and Materials
  8. ASTM E1355-12 Standard Guide for Evaluating the Predictive Capability of Deterministic Fire Models
  9. ASTM E1537-13 Standard Test Method for Fire Testing of Upholstered Furniture
  10. ASTM E1546-09a Standard Guide for Development of Fire-Hazard-Assessment Standards
  11. ASTM E1590-13 Standard Test Method for Fire Testing of Mattresses
  12. ASTM E1591-13 Standard Guide for Obtaining Data for Fire Growth Models
  13. ASTM E1678-10 Standard Test Method for Measuring Smoke Toxicity for Use in Fire Hazard Analysis
  14. ASTM E176-13 Standard Terminology of Fire Standards
  15. ASTM E1776-13 Standard Guide for Development of Fire-Risk-Assessment Standards
  16. ASTM E1822-12 Standard Test Method for Fire Testing of Stacked Chairs
  17. ASTM E2032-09(2013) Standard Guide for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119
  18. ASTM E2058-13a Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA)
  19. ASTM E2061-12 Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles
  20. ASTM E2174-10ae1 Standard Practice for On-Site Inspection of Installed Fire Stops
  21. ASTM E2257-13a Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
  22. ASTM E2280-13 Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
  23. ASTM E2307-10 Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story Test Apparatus
  24. ASTM E2336-04(2013) Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
  25. ASTM E2393-10a Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers
  26. ASTM E2574/E2574M-12a Standard Test Method for Fire Testing of School Bus Seat Assemblies
  27. ASTM E2632/E2632M-13e1 Standard Test Method for Evaluating the Under-Deck Fire Test Response of Deck Materials
  28. ASTM E2707-09 Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure
  29. ASTM E2726/E2726M-12a Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands
  30. ASTM E2748-12a Standard Guide for Fire-Resistance Experiments
  31. ASTM E2816-13a Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems
  32. ASTM E2912-13 Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction
  33. ASTM E535-12 Standard Practice for Preparation of Fire-Test-Response Standards
  34. ASTM E603-13 Standard Guide for Room Fire Experiments
  35. ASTM E605-93(2011) Standard Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members
  36. ASTM E69-02(2007) Standard Test Method for Combustible Properties of Treated Wood by the Fire-Tube Apparatus
  37. ASTM E859-93(2011) Standard Test Method for Air Erosion of Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Members
  38. ASTM F1198-92(2012)e1 Standard Guide for Shipboard Fire Detection Systems
  39. ASTM F1534-10 Standard Test Method for Determining Changes in Fire-Test-Response Characteristics of Cushioning Materials After Water Leaching
  40. ASTM F1870-11 Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities
  41. ASTM F1989-05(2013) Standard Specification for Cooking Fire Suppression Blankets
  42. ASTM F1989-05(2013) Standard Specification for Cooking Fire Suppression Blankets
  43. ASTM F2058-07 Standard Specification for Candle Fire Safety Labeling
  44. ASTM G145-08 Standard Guide for Studying Fire Incidents in Oxygen Systems
  45. STP1163 Fire Standards in the International Marketplace
  46. STP1284 Fire Resistance of Industrial Fluids
  47. STP1427 Thermal Measurements: The Foundation of Fire Standards
  48. STP1427 Thermal Measurements: The Foundation of Fire Standards
  49. STP1517 Advances in the State of the Art of Fire Testing
  50. STP1541 Uncertainty in Fire Standards and What to Do About It
  51. STP344 Symposium on Fire Test Methods (1962)
  52. STP385 Moisture in Materials in Relation to Fire Tests
  53. STP406 Fire Resistance of Hydraulic Fluids
  54. STP422 Symposium on Fire Test Methods—Restraint & Smoke 1966
  55. STP464 Fire Test Performance
  56. STP464 Fire Test Performance
  57. STP502 Ignition, Heat Release, and Noncombustibility of Materials
  58. STP685 Design of Buildings for Fire Safety
  59. STP762 Fire Risk Assessment
  60. STP816 Behavior of Polymeric Materials in Fire

GOST

  1. GOST 12.1.004-91  Occupational safety standards system. Fire safety. General requirements
  2. GOST 12.1.018-93  Occupational safety standards system. Fire and explosion safety of static electricity. General requirements
  3. GOST 12.1.033-81  Occupaticnal safety standards system. Fire safety. Terms and defintions
  4. GOST 12.1.044-89   Occupational safety standards system. Fire and explosion hazard of substances and materials. Nomenclature of indices and methods of their determination
  5. GOST 12.1.114-82  Occupational safety standards system. Fire engineering. Symbolic representations
  6. GOST 12.3.046-91  Occupational safety standards system. Automatic fire fighting systems. General technical requirements
  7. GOST 14286-69  Wrenches for fire connecting equipment. Specifications
  8. GOST 15635-70  Refractory fire-clay products for hot-metal transier ladles lining. Specifications
  9. GOST 16363-98  Fire protective means for wood. Methods for determination of fire protective properties
  10. GOST 16714-71  Non-mechanized hand fire instruments. Specifications
  11. GOST 19297-2003  Treated for fire-resistance cotton fabrics. Specifications
  12. GOST 2071-69  Straps for fire-hoses
  13. GOST 23787.12-81  Solutions of biological fire retarding compound ПБC. Technical requirements, safety requirements and methods of analysis
  14. GOST 23787.7-79  Solutions of fire retarding preservative ПББ. Technical requirements, safety requirements and methods of analysis
  15. GOST 23790-79  Phosphates fire protective wood coating. Technical requirements
  16. GOST 23791-79  Phosphates fire protective still coating. Technical requirements
  17. GOST 23859.10-79  Bronze fire-resistance. Methods for the determination of titanium
  18. GOST 23859.1-79  Bronze fire-resistance. Method for the determination of copper
  19. GOST 23859.2-79  Bronze fire-resistance. Methods for the determination of silicon
  20. GOST 23859.3-79  Bronze fire-resistance. Methods for the determination of chromium
  21. GOST 23859.4-79  Bronze fire-resistance. Method for the determination of phosphorus
  22. GOST 23859.5-79  Bronze fire-resistance. Methods for the determination of iron
  23. GOST 23859.6-79  Bronze fire-resistance. Method for the determination of nickel
  24. GOST 23859.7-79  Bronze fire-resistance. Method for the determination of lead
  25. GOST 23859.8-79  Bronze fire-resistance. Methods for the determination of zirconium
  26. GOST 23859.9-79  Bronze fire-resistance. Method for the determination of cobalt
  27. GOST 24018.0-90  Nickel-based fire-resistant alloys. General requirements for methods of analysis
  28. GOST 24018.7-91  Nikel-based fire-resistant alloys. Methods for the determination of carbon
  29. GOST 24018.8-91  Nikel-based fire-ressistant alloys. Methods for the determination of sulphur
  30. GOST 25130-82  Intumescent fire protective wood coating. Technical requirements
  31. GOST 25131-82  Intumescent fire protective steel coating. Technical requirements
  32. GOST 25665-83  Phosphates fire protective steel coating of the mineral fibres. Technical requirements
  33. GOST 26342-84  Means of alarm, fire and alarm-fire systems. Types, basic parameters and dimensions
  34. GOST 27331-87  Fire engineering. Cassification of fires
  35. GOST 27483-87  Fire hazard testing. Test methods. Glow-wire test and guidance
  36. GOST 27484-87  Fire hazard testing. Test methods. Needle-flame test
  37. GOST 27924-88  Fire-hazard testing. Test methods. Bad-connection test with heaters
  38. GOST 27990-88  Means of alarm, fire and alarm-fire systems. General technical requirements
  39. GOST 28130-89  Fire engineering. Fire extinguishers, fire extinguishing systems and fire alarm systems. Grafical conventional signs
  40. GOST 31251-2008 Facades of buildings. Fire hazard test method
  41. GOST 30135-94  Fabricknitting carcasses for fire hoses. General specifications
  42. GOST 30247.0-94  Elements of building constructions. Fire-resistance test methods. General requirements
  43. GOST 30247.1-94  Elements of building constructions. Fire-resistance tests methods. Load-bearing and separating constructions
  44. GOST 30247.3-2002  Building structures. Fire-resistance tests methods. Elevator shaft doors
  45. GOST 30403-2012  Building structures. Fire hazard test method
  46. GOST 31251-2008  Facades of buildings. Fire hazard test method
  47. GOST 31565-2012  Cable products. Requirements of fire safety
  48. GOST 4.107-83  System of product quality indices. Fire-extinguishing powders. Nomenclature of indices
  49. GOST 4.188-85  Product-quality index system. Means for guarding, fire and guarding fire signalization. Nomenclature of indices
  50. GOST 4.331-85  Product-quality index system. Fire power pumps. Nomenclature of indices
  51. GOST 4.332-85  Product-quality index system. Fire extinguishing trucks. Nomenclature of indices
  52. GOST 4.407-85  Product-quality index system. Sporting, hunting and sport-hunting cartridges for rifled fire-arms. Index nomenclature
  53. GOST 4.445-86  Product-quality index system. Charging stations for fire extinguishers. Index nomenclature
  54. GOST 4.99-83  System of product quality indexes. Foaming agents for fire extinguishing. Nomenclature of indexes
  55. GOST 8556-72  Portable wood fire ladders
  56. GOST EN 13478-2012  Safety of machinery. Fire prevention and protection
  57. GOST EN 407-2012  Occupational safety standards system. Personal protective means of hands. Protective gloves from heat and fire. Technical requirements. Test methods
  58. GOST IEC 60331-12-2011  Tests for electric cables under fire conditions. Circuit integrity. Part 12. Apparatus. Fire with shock at a temperature of at least 830 °C
  59. GOST IEC 60331-21-2011  Tests for electric and optical fibre cables under fire conditions. Circuit integrity. Part 21. Procedures and requirements. Cables of rated voltage up to and including 0,6/1,0 kV
  60. GOST IEC 60331-23-2011  Tests for electric and optical fibre cables under fire conditions. Circuit integrity. Part 23. Procedures and requirements. Electric data cables
  61. GOST IEC 60331-23-2011  Tests for electric and optical fibre cables under fire conditions. Circuit integrity. Part 23. Procedures and requirements. Electric data cables
  62. GOST IEC 60331-25-2011  Tests for electric and optical fibre cables under fire conditions. Circuit integrity. Part 25. Procedures and requirements. Optical fibre cables
  63. GOST IEC 60331-31-2011  Tests for electric cables under fire conditions. Circuit integrity. Part 31. Procedures and requirements for fire with shock. Cables of rated voltage up to and including 0,6/1,0 kV
  64. GOST IEC 60332-1-1-2011  Tests on electric and optical fibre cables under fire conditions. Part 1-1. Test for vertical flame propagation for a single insulated wire or cable. Apparatus
  65. GOST IEC 60332-1-2-2011  Tests on electric and optical fibre cables under fire conditions. Part 1-2. Test for vertical flame propagation for a single insulated wire or cable. Procedure for 1 kW pre-mixed flame
  66. GOST IEC 60332-1-3-2011  Tests on electric and optical fibre cables under fire conditions. Part 1-3. Test for vertical flame propagation for a single insulated wire or cable. Procedure for determination of flaming droplets/particles
  67. GOST IEC 60332-2-1-2011  Tests on electric and optical fibre cables under fire conditions. Part 2-1. Test for vertical flame propagation for a single small insulated wire or cable. Apparatus
  68. GOST IEC 60332-2-2-2011  Tests on electric and optical cables under fire conditions. Рart 2 -2. Test for vertical flame propagation for a single small insulated wire or cable. Procedure for diffusion flame
  69. GOST IEC 60332-3-21-2011  Tests on electric and optical cables under fire conditions. Part 3-21. Flame spread of vertically-mounted bunched wires or cables. Category A F/R
  70. GOST IEC 60332-3-22-2011  Tests on electric and optical cables under fire conditions. Рart 3-22. Flame spread of vertically-mounted bunched wires or cables. Category A
  71. GOST IEC 60332-3-23-2011  Tests on electric and optical cables under fire conditions. Рart 3-23. Flame spread of vertically-mounted bunched wires or cables. Category B
  72. GOST IEC 60332-3-24-2011  Tests on electric and optical cables under fire conditions. Рart 3-24. Flame spread of vertically-mounted bunched wires or cables. Category C
  73. GOST IEC 60332-3-25-2011  Tests on electric and optical cables under fire conditions. Рart 3-25. Flame spread of vertically-mounted bunched wires or cables. Category D
  74. GOST IEC 60695-10-2-2013  Fire hazard testing. Part 10-2. Abnormal heat. Ball pressure test
  75. GOST IEC 60695-2-11-2013  Fire hazard testing. Part 2-11. Glowing/hot-wire based test methods. Glow-wire flammability test method for end-products
  76. GOST IEC 60695-2-13-2012  Fire hazard testing. Part 2-13. Glowing/hot-wire based test methods. Glow-wire ignition temperature (GWIT) test method for materials
  77. GOST R 12.2.144-2005  Occupational safety standards system. Fire-fighting technics. Safety requirements. Test methods
  78. GOST R 12.3.047-2012  Occupational safety standards system. Fire safety of technological processes. General requirements. Methods of control
  79. GOST R 12.3.047-2012  Occupational safety standards system. Fire safety of technological processes. General requirements. Methods of control
  80. GOST R 12.4.294-2013  Occupational safety standards system. Respiratory protective devices for self­rescue. Filtering devices with hood for escape from fire. Requirements, testing, marking
  81. GOST R 22.1.09-99  Safeti in emergencies. Monitoring and forecasing of forest fire. General requirements
  82. GOST R 41.34-2001  Uniform provisions concerning the type approval of vehicles with regard to the prevention of fire risks
  83. GOST R 50398-92  Fire hydraulic elevator. Specifications
  84. GOST R 50400-2011  Fire-fighting equipment. Hose branchings. General technical requirements. Test methods
  85. GOST R 50529-2010  Civil and service fire-arms, industrial and special devices. Safetу requirements and test methods for safetу
  86. GOST R 50530-2010  Cartridges for civil and service fire-arms, industrial and special devices. Safetу requirements and test methods for safetу
  87. GOST R 50571.17-2000  Electrical installations of buildings. Part 4. Protection for safety. Chapter 48. Choice of protective measures as a function of external influences. Section 482. Protection against fire
  88. GOST R 50588-2012  Foaming agents for fire extinguishing. General technical requirements and test methods
  89. GOST R 50862-2012  Safes, safe rooms and strong rooms. Requirements and methods of tests for resistance to burglary and fire
  90. GOST R 50969-96  Automatic gas fire extinguishing systems. General technical requirements. Test methods
  91. GOST R 50982-2009  Fire equipment. Specialized fires department tools. General technical requirements. Test methods
  92. GOST R 51013-97  Nickel based fire-resistant, corrosion-resistant, precision alloys. Methods for titanium determination
  93. GOST R 51017-2009  Fire engineering. Wheeled fire extinguishers. General technical requirements. Test methods
  94. GOST R 51043-2002  Аutomatic water and foam fire fighting systems. Sprinklers, spray nozzles and water mist nozzles. General technical requirements. Test methods
  95. GOST R 51049-2008  Fire equipment. Pressure fire hoses. General technical requirements. Test methods
  96. GOST R 51052-2002  Аutomatic water and foam fire extinguishing installations. Wet and dry systems alarm stations. General technical requirements. Test methods
  97. GOST R 51057-2001  Fire fighting equipment. Portable fire extinguishers. General technical requirements. Test methods
  98. GOST R 51072-2005  Protection doors. General technical requirements and test methods for resistance to burglary, bullet and fire
  99. GOST R 51091-97  Automatic dry chemical fire fighting systems. Types and dasic parameters
  100. GOST R 51115-97  Fire equipment. Fire turntable combined monitors. General technical requirements. Test methods
  101. GOST R 51589-2000  Self-defence tubeless fire-arms (complex “OSA”). General technical requirements and test methods
  102. GOST R 51611-2000  Special purpose rounds for self-defense tubeless fire-arms (complex “OSA”). General technical requirements. Safety requirements and test methods
  103. GOST R 51737-2001  Automatic water and foam fire fighting systems. Sectional tubing couplings. General technical requirements. Methods of tests
  104. GOST R 51844-2009  Fire equipment. Fire-fighting cabinets. General technical requirements. Test methods
  105. GOST R 51879-2002  Fire-arms. Procedure of approval of proof marks of countries-members of International Permanent Commitee on testing small-arms
  106. GOST R 51888-2002  Civil and service gas-arms and fire-arms. Classification
  107. GOST R 51901.10-2009  Risk management. Fire risk management in enterprise
  108. GOST R 51928-2002  Nickel-based fire-resistant alloys. Methods for determination of boron
  109. GOST R 52283-2004  Fire-fighting centrifugal pumps. General technical requirements. Test methods
  110. GOST R 52284-2004  Fire aerial ladders. General technical requirements. Test methods
  111. GOST R 52316-2005  Fire equipment. Thermal equipment trips. General technical requirements. Test methods
  112. GOST R 52436-2005  Control equipment of intruder and intruder-fire alarm systems. Classification. General technical requirements and test methods
  113. GOST R 52625-2006  Lifts. Landing doors. Fire resistance test methods
  114. GOST R 52919-2008  Information technology. Physical security techniques. Classification and methods of tests for resistance to fire. Data rooms and data containers
  115. GOST R 53247-2009  Fire-fighting technics. Fire-engine vehicles. Classification, types and designations
  116. GOST R 53248-2009  Fire fighting technics. Fire fighting vehicles. Nomenclature of indices
  117. GOST R 53249-2009  Fire-fighting equipment. Sleeved watercollecting. General technical requirements. Methods of testing
  118. GOST R 53250-2009  Fire-fighting equipment. Fire standpipe. General technical requirements. Methods of testing
  119. GOST R 53251-2009  Fire-fighting equipment. Hand foam-nozzles. General technical requirements. Methods of testing
  120. GOST R 53252-2009  Fire-fighting equipment. Foammixers. General technical requirements. Methods of testing
  121. GOST R 53253-2009  Fire-fighting equipment. Suction gauzes. General technical requirements. Methods of testing
  122. GOST R 53254-2009  Fire equipment. Ed fire ladders to be installed outside buildings. Buildings roof railings. General technical requirements. Test methods
  123. GOST R 53255-2009  Fire equipment. Self-contained open-circuit compressed air breathing apparatus. General technical requirements. Test methods
  124. GOST R 53256-2009  Fire equipment. Self-contained closed-circuit breathing apparatus with compressed oxygen. General technical requirements. Test methods
  125. GOST R 53257-2009  Fire equipment. Full face masks breathing apparatus. General technical requirements. Test methods
  126. GOST R 53258-2009  Fire equipment. The small size cylinders for apparatuses breathing and self-contained escape with compressed air. General technical requirements. Test methods
  127. GOST R 53259-2009  Fire equipment. Self-contained escape with compressed air for protection of the people against toxic products at evacuation from smoking buildings from fire. General technical requirements. Test methods
  128. GOST R 53260-2009  Fire equipment. Self-contained escape with chemical oxygen for protection of the people against toxic products at evacuation from smoking buildings from fire. General technical requirements. Test methods
  129. GOST R 53261-2009  Fire equipment. Filter self-rescue for protection of people against toxic products at evacuation from smoking buildings from fire. General technical requirements. Test methods
  130. GOST R 53262-2009  Fire equipment. Devices for control breathing apparatuses. General technical requirements. Test methods
  131. GOST R 53263-2009  Fire equipment. Compressor unit for filling of low-volume ballons with compress air breathing apparatus for fireman. General technical requirements. Test methods
  132. GOST R 53264-2009  Fire equipment. Special clothing for fire-fighter. General technical requirements. Test methods
  133. GOST R 53265-2009  Mean of individual defence of feet for fire-fighter. General technical requirements. Test methods
  134. GOST R 53266-2009  Fire equipment. Fire saving cord. General technical requirements. Test methods
  135. GOST R 53267-2009  Fire equipment. Fire snap hook. General technical requirements. Test methods
  136. GOST R 53268-2009  Fire equipment. Fire safety belt. General technical requirements. Test methods
  137. GOST R 53269-2009  Fire equipment. Helmets for firefighters. General technical requirements. Test methods
  138. GOST R 53270-2009  Fire equipment. Fire lantern. General technical requirements. Test methods
  139. GOST R 53271-2009  Fire equipment. Fire escape chute. General technical requirements. Test methods
  140. GOST R 53272-2009  Fire equipment. Fire rope descenders. General technical requirements. Test methods
  141. GOST R 53273-2009  Fire equipment. Fire jumping down rescue devices. General technical requirements. Test methods
  142. GOST R 53274-2009  Fire equipment. Fire rescue chute. General technical requirements. Test methods
  143. GOST R 53275-2009  Fire equipment. Fire departament hand-operated ladders. General technical requirements. Test methods
  144. GOST R 53276-2009  Fire equipment. Hanging ladders for rescue from height. General technical requirements. Test methods
  145. GOST R 53277-2009  Fire equipment. Equipment for maintenance of fire hoses. General technical requirements. Methods of testing
  146. GOST R 53278-2009  Fire equipment. Fire valves. General technical requirements. Test methods
  147. GOST R 53279-2009  Fire equipment. Fire connecting heads. General technical requirements. Methods of testing
  148. GOST R 53280.1-2010  Automatic fire extinguishing systems. Fire extinguishing media. Part 1. Foam fire extinguishing concentrates for surface application to water – miscible liquids. General technical requirements and test methods
  149. GOST R 53280.2-2010  Automatic fire extinguishing systems. Fire extinguishing media. Part 2. Foams concentrate for subsurface extinguishing of fires oil and petroleum tanks. General technical requirements and test methods
  150. GOST R 53280.3-2009  Automatic fire extinguishing systems. Fire extinguishing media. Part 3. Gaseous extinguishing media. Test methods
  151. GOST R 53280.4-2009  Automatic fire extinguishing systems. Extinguishing medium. Part 4. Dry fire extinguishing powders. General technical requirements and test methods
  152. GOST R 53280.5-2009  Automatic fire extinguishing systems. Extinguishing medium. Part 5. Special dry fire extinguishing powders. Classification, general technical requirements.Test methods
  153. GOST R 53281-2009  Automatic gas fire extinguishing systems. Cylinders and cylinder banks. General technical requirements. Test methods
  154. GOST R 53282-2009  Automatic gas fire extinguishing systems. Isothermal tanks. General technical requirements. Test methods
  155. GOST R 53283-2009  Automatic gas fire extinguishing systems. Distributing valves. General technical requirements. Test methods
  156. GOST R 53284-2009  Fire engineering. Generators of extinguishing aerosol. General technical requirements. Test methods
  157. GOST R 53285-2009  Fire engineering. Portable generators of extinguishing aerosol. General technical requirements. Test methods
  158. GOST R 53286-2009  Fire engineering. Automatic dry chemical fire fighting system. Module. General technical requirements. Test methods
  159. GOST R 53287-2009  Water and foam fire fighting systems. Fire alarm hydraulic, fire foam inducer, feeder. General technical requirements. Test methods
  160. GOST R 53288-2009  Automatic water and foam extinguishers systems. Automatic fire water mist spray extinguishers systems. Modules. General technical requirements. Test methods
  161. GOST R 53289-2009  Ceiling type water sprinklers (concealed, flush and recessed). Fire sensitivity test
  162. GOST R 53290-2009  Fire engineering. Foam fire-extinguishing installations. Low expansion foam generators for subsurfase extinguishing in tanks. General technical requirements. Test methods
  163. GOST R 53291-2009  Portable and movable devices of fire extinguishing with high-velosity submission of fire quenching matter. General technical requirements. Test methods
  164. GOST R 53292-2009  Fire retardant compositions and substances for wood. General requirements. Test methods
  165. GOST R 53293-2009  Fire hazard of substances and materials. Materials, substance and fire protective means. Identification by thermal analysis methods
  166. GOST R 53295-2009  Fire retardant compositions for steel constructions. General requirement. Method for determining fire retardant efficiency
  167. GOST R 53296-2009  Fire fighting lifts placing. Requirements of fire safety
  168. GOST R 53298-2009  Suspended ceilings. Fire resistance test method
  169. GOST R 53299-2009  The test method for the fire resistance. Ventilation ducts
  170. GOST R 53299-2013  Ventilation ducts. The test method for the fire resistance
  171. GOST R 53301-2009  Fire dampers of ventilation systems. The test method for the fire resistance
  172. GOST R 53301-2013  Fire dampers of ventilation systems. The test method for the fire resistance
  173. GOST R 53302-2009  The equipment of smoke control systems. The test method for the fire resistance
  174. GOST R 53303-2009  Building constructions. Fire doors and gates. Test methods for smoke-and-gas leakage
  175. GOST R 53304-2009  Trunks of refuse chutes. The test method on fire resistance
  176. GOST R 53305-2009  Smoke shields. The test method for the fire resistance
  177. GOST R 53306-2009  Enclosing building structures crossing junction points by using pipe, which is made of polymeric materials. Fire resistance test
  178. GOST R 53307-2009  Elements of building constructions. Fire doors and gates. Fire resistance test method
  179. GOST R 53309-2009  Buildings and building’s fragments. Method of real fire tests. General requirements
  180. GOST R 53310-2009  Through penetration for cables, hermetic inputs and through penetration of electric current types. Requirements of fire safety. Fire resistance test methods
  181. GOST R 53311-2009  Coatings cables fire retardant. Methods for determination of fireproof efficiency
  182. GOST R 53313-2009  Electrical mounting appliances. Requirements of fire safety. Test methods
  183. GOST R 53316-2009  Cable lines. Circuit integrity under fire. Test method
  184. GOST R 53321-2009  Thermal devices on various kind of fuel. Fire safety requirements. Test methods
  185. GOST R 53324-2009  Dyking of storage tanks. Fire safety requirements
  186. GOST R 53325-2012  Fire techniques. Means of fire automatics. The general technical requirements. Test methods
  187. GOST R 53326-2009  Fire equipment. Self-contained open-circuit compressed air breathing apparatus. General technical requirements. Test methods
  188. GOST R 53328-2009  Fire fighting technics. Fire extingushing trucks. General technical requirements. Test methods
  189. GOST R 53329-2009  Fire elevators. General technical requirements. Test methods
  190. GOST R 53331-2009  Fire-fighting equipment. Hand nozzles. General technical requirements. Methods of testing
  191. GOST R 53332-2009  Fire equipment. Fire motor pumps. Main parameters. General technical requirements. Methods of testing
  192. GOST R 53961-2010  Fire-fighting equipment. Underground fire hydrants. General technical requirements. Test methods
  193. GOST R 54019-2010  Fire hazard testing. Part 2-20. Glowing/hot-wire based test methods. Hot-wire coil ignitability. Apparatus, test method and guidance
  194. GOST R 54081-2010  Influence of environmental conditions appearing in nature on the technical products. Overall performance. Fire
  195. GOST R 54103-2010  Fire hazard testing. Test methods. Glow-wire test and guidance
  196. GOST R 54344-2011  Fire equipment. Mobile manipulation vehicle systems for eliminating of emergencies and fire extinguishing. Classification. General technical requirements. Test methods
  197. GOST R 54495-2011  Glass and glass products. Fire resistance test method
  198. GOST R 55149-2012  Fire techniques. Individual fire alarm devices. The general technical requirements. Test methods
  199. GOST R 55183-2012  Passenger cars on locomotive traction. Fire safety requirements
  200. GOST R 55230-2012  Marine, locomotive and industrial engines. Fire protection requirements
  201. GOST R 55895-2013  Fire equipment. Robotics control systems for eliminating of emergencies and fire extinguishing. General technical requirements. Test methods
  202. GOST R 55896-2013  Building structures. Doors the enclosures of lift shaft. Fire resistance test method
  203. GOST R IEC 60331-11-2012  Tests for electric and optical cables under fire conditions. Circuit integrity. Part 11. Apparatus. Fire alone at a flame temperature of at least 750 °C
  204. GOST R IEC 60332-3-10-2011  Tests on electric and optical fibre cables under fire conditions. Part 3-10. Flame spread of vertically-mounted bunched wires or cables. Apparatus
  205. GOST R IEC 60695-10-2-2010  Fire hazard testing. Part 10-2. Abnormal heat. Ball pressure test
  206. GOST R IEC 60695-1-1-2003  Fire hazard testing. Part 1-1. Guidance for assessing the fire hazard of electrotechnical products. General guidelines
  207. GOST R IEC 60695-2-10-2011  Fire hazard testing. Part 2-10. Glowing/hot-wire based test methods. Glow-wire apparatus and common test procedures
  208. GOST R IEC 60695-2-11-2010  Fire hazard testing. Part 2-11. Glowing/hot-wire based test methods. Glow-wire flammability test method for end-products
  209. GOST R IEC 60695-2-2-2011  Fire hazard testing. Part 2. Test methods. Section 2. Needle-flame test
  210. GOST R ISO 3935-2005  Shipbuilding. Inland navigation. Fire-fighting water system. Pressures
  211. GOST R ISO 5797-2010  Ships and marine technology. Windows and side scuttles for fire-resistant constructions
  212. GOST R ISO 6942-2007  Occupational safety standards system. Clothing for protection against heat and fire. Assessment methods of materials and material assemblies when exposed to а source of radiant heat

 

건설 및 건축자재 유럽인증서 취득 대상

23 Dec 2013 Comments
Off

CE Mark  건축자재 인증 대상품 [CE Marking CPR/CPD Construction Products]

건설 및 토목 공사 목적물의 일부를 구성하는 모든 제품입니다. 일반적으로 건축, 건설 등 공사목적물이 완성되었을 때 목적물의 일부로써 존재하는 것들로 이해합니다.

대별하면, 시멘트류, 모르타르, 석고 등 단열재류, 바닥, 벽, 천정재류, 지붕재 및 누수방지재류 및 설비류,구조용 베어링류, 액체 보관 탱크류, 골재류, 충진재류, 닥트, 밸브 및 파이프, 캡류, 창호 및 도어류, 유리, 타일 및 내외장재류, 접착제류, 도로건설용 자재 및 설비, 교통제어 시스템류, 도로 표지판류, 화재감지 및 소방시설류, 건축용 하드웨어류, 화장실 변기류, 주방용 자재류, 조명용 기둥류, 도로 안전시설 자재류, 구조용 목재류, 굴뚝, 히터 등 난방 설비류, 폐수처리 설비, 상수도 설비 등이 있습니다.

인증 대상품목은 국한되지 않으나 다음과 같습니다.

1)     강철 구조물
2)     건물 보온 제품
3)     건물 홍수 방지장치
4)     건물의 유리
5)     건축용 하드웨어

6)     공기 히터, 버너 및 난방기
7)     교통 제어 장비
8)     교통 표지판
9)     구조 베어링
10)   구조용 목재

11)   구조용 볼트
12)   구조용 알루미늄 및 알루미늄 합금
13)   구조용 철강의 열연 제품
14)   구조용 주조물
15)   굴뚝

16)   금속 시트 및 루핑(지붕재)
17)   내장재(벽지, 바닥재 카펫트, 천정재 등)
18)   도로 표지판
19)   도로 바닥 마킹 자재
20)   라미네이트 바닥

21)   루핑 타일 및 피팅
22)   루핑용 조립식 부속품
23)   메탈 호스 어셈블리
24)   모듈형 타일 바닥과 계단 (내부 및 외부)
25)   방수 시트

26)   방진장치
27)   배관 시스템을 위한 접착제
28)   배수용 관이음
29)   벽돌
30)   보일러

31)   볼 밸브
32)   비 전기 자동 제어와 제연 장치
33)   비 합금 스틸 튜브
34)   사우나 스토브
35)   석고 기반의 접착제

36)   석고 plasterboard 제품
37)   섬유 석고
38)   세라믹 굴뚝 라이너
39)   세라믹 연도 블록
40)   세라믹 타일

41)   소방 댐퍼
42)   소방 시스템
43)   소방경보 장치
44)   소방용기 밸브 조립과 액츄에이터
45)   소변기

46)   소화 시스템
47)   스테인리스 파이프 피팅
48)   스틸 섬유
49)   스프링 쿨러
50)   슬레이트 및 석재

51)   시멘트
52)   아스팔트
53)   알루미늄 구조물
54)   역청탄의 혼합물
55)   연기 및 열 제어 시스템

56)   오버헤드 복사 튜브 히터 시스템
57)   외부 블라인드
58)   욕조
59)   자물쇠 래치
60)   자연석

61)   장식용 라미네이트 (HPL)
62)   점토 블록
63)   접착 적층 목재
64)   정화조 탱크
65)   조명용 기둥

66)   주방용 자재(싱크 등)
67)   지붕의 기와와 지붕 덮개
68)   지상 스토리지탱크
69)   차고 문과 게이트
70)   차량 및 보행자 영역에 대한 배수 채널

71)   창문과 문
72)   천연 석재 제품
73)   철 파이프와 피팅
74)   철도 바닥짐
75)   캐스트 폴리 우레탄 씰링

76)   커튼 웰
77)   콘크리트 블록 및 맨홀
78)   콘크리트 파이프 및 부품
79)   콘크리트
80)   파이버

81)   건축용 파이프
82)   폐수 처리 시스템
83)   건축용 폴리 (염화 비닐) (PVC-U) 프로파일
84)   건축용 폴리머 섬유
85)   프리 캐스트

86)   플라이 애쉬
87)   플러그 밸브
88)   필러 및 실런트
89)   하수도 어플 리케이션을위한 연성 철 파이프, 피팅, 부속품과 관절
90)   화재 감지 및 화재 경보 시스템

91)   Geosynthetic 관련 제품
92)   Geotextiles과 geotextile 관련 제품
93)   plasterboard 시스템을위한 금속 프레임
94)   PVC-UE 프로파일

* 위 품목외의 경우, 메일(anycerti@gmail.com)로 상담 바랍니다.

List of Norm to be applied for Machinery Directive CE Marking

23 Dec 2013 Comments
Off

CE Mark 기계지침 관련 EN 규격 목록

EN 1005-1:2001+A1:2008-Safety of machinery – Human physical performance – Part 1: Terms and definitions

EN 1005-2:2003+A1:2008-Safety of machinery – Human physical performance – Part 2: Manual handling of machinery and component parts of machinery

EN 1005-3:2002+A1:2008-Safety of machinery – Human physical performance – Part 3: Recommended force limits for machinery operation

EN 1005-4:2005+A1:2008-Safety of machinery – Human physical performance – Part 4: Evaluation of working postures and movements in relation to machinery

EN 1010-1:2004+A1:2010-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 1: Common requirements

EN 1010-2:2006+A1:2010-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 2: Printing and varnishing machines including pre-press machinery

EN 1010-3:2002+A1:2009-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 3: Cutting machines

EN 1010-4:2004+A1:2009-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 4: Bookbinding, paper converting and finishing machines

EN 1012-1:2010-Compressors and vacuum pumps – Safety requirements – Part 1: Air compressors

EN 1012-2:1996+A1:2009-Compressors and vacuum pumps – Safety requirements – Part 2: Vacuum pumps

EN 1028-1:2002+A1:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 1: Classification – General and safety requirements

EN 1028-2:2002+A1:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 2: Verification of general and safety requirements

EN 1032:2003+A1:2008-Mechanical vibration – Testing of mobile machinery in order to determine the vibration emission value

EN 1034-1:2000+A1:2010-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 1: Common requirements

EN 1034-13:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 13: Machines for de-wiring bales and units

EN 1034-14:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 14: Reel splitter

EN 1034-16:2012 (new)-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 16: Paper and board making machines

EN 1034-2:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 2: Barking drums

EN 1034-22:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 22: Wood Grinders

EN 1034-3:2011-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 3: Rereelers and winders

EN 1034-4:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 4: Pulpers and their loading facilities

EN 1034-5:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 5: Sheeters

EN 1034-6:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 6: Calender

EN 1034-7:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 7: Chests

EN 1034-8:2012 (new)-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 8: Refining plants

EN 1037:1995+A1:2008-Safety of machinery – Prevention of unexpected start-up

EN 1088:1995+A2:2008-Safety of machinery – Interlocking devices associated with guards – Principles for design and selection

EN 1093-1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 1: Selection of test methods

EN 1093-11:2001+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 11: Decontamination index

EN 1093-2:2006+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant

EN 1093-3:2006+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 3: Test bench method for the measurement of the emission rate of a given pollutant

EN 1093-4:1996+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 4: Capture efficiency of an exhaust system – Tracer method

EN 1093-6:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 6: Separation efficiency by mass, unducted outlet

EN 1093-7:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 7: Separation efficiency by mass, ducted outlet

EN 1093-8:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 8: Pollutant concentration parameter, test bench method

EN 1093-9:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 9: Pollutant concentration parameter, room method

EN 1114-1:2011-Plastics and rubber machines – Extruders and extrusion lines – Part 1: Safety requirements for extruders

EN 1114-3:2001+A1:2008-Plastics and rubber machines – Extruders and extrusion lines – Part 3: Safety requirements for haul-offs

EN 1127-1:2011-Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts and methodology

EN 1127-2:2002+A1:2008-Explosive atmospheres – Explosion prevention and protection – Part 2: Basic concepts and methodology for mining

EN 115-1:2008+A1:2010-Safety of escalators and moving walks – Part 1: Construction and installation

EN 1175-1:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 1: General requirements for battery powered trucks

EN 1175-2:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 2: General requirements of internal combustion engine powered trucks

EN 1175-3:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 3: Specific requirements for the electric power transmission systems of internal combustion engine powered trucks

EN 12001:2003+A1:2009-Conveying, spraying and placing machines for concrete and mortar – Safety requirements

EN 12012-1:2007+A1:2008-Plastics and rubber machines – Size reduction machines – Part 1: Safety requirements for blade granulators

EN 12012-3:2001+A1:2008-Plastics and rubber machines – Size reduction machines – Part 3: Safety requirements for shredders

EN 12012-4:2006+A1:2008-Plastics and rubber machines – Size reduction machines – Part 4: Safety requirements for agglomerators

EN 12013:2000+A1:2008-Plastics and rubber machines – Internal mixers – Safety requirements

EN 12016:2004+A1:2008-Electromagnetic compatibility – Product family standard for lifts, escalators and moving walks – Immunity

EN 12041:2000+A1:2009-Food processing machinery – Moulders – Safety and hygiene requirements

EN 12042:2005+A1:2010-Food processing machinery – Automatic dividers – Safety and hygiene requirements

EN 12043:2000+A1:2010-Food processing machinery – Intermediate provers – Safety and hygiene requirements

EN 12044:2005+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Cutting and punching machines – Safety requirements

EN 12053:2001+A1:2008-Safety of industrial trucks – Test methods for measuring noise emissions

EN 12077-2:1998+A1:2008-Cranes safety – Requirements for health and safety – Part 2: Limiting and indicating devices

EN 12110:2002+A1:2008-Tunnelling machines – Air locks – Safety requirements

EN 12111:2002+A1:2009-Tunnelling machines – Road headers, continuous miners and impact rippers – Safety requirements

EN 12158-1:2000+A1:2010-Builders’ hoists for goods – Part 1: Hoists with accessible platforms

EN 12158-2:2000+A1:2010-Builders’ hoists for goods – Part 2: Inclined hoists with non-accessible load carrying devices

EN 12159:2000+A1:2009-Builders hoists for persons and materials with vertically guided cages

EN 12162:2001+A1:2009-Liquid pumps – Safety requirements – Procedure for hydrostatic testing

EN 1218-1:1999+A1:2009-Safety of woodworking machines – Tenoning machines – Part 1: Single end tenoning machines with sliding table

EN 1218-2:2004+A1:2009-Safety of woodworking machines – Tenoning machines – Part 2: Double end tenoning and/or profiling machines fed by chain or chains

EN 1218-3:2001+A1:2009-Safety of woodworking machines – Tenoning machines – Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers

EN 1218-4:2004+A2:2009-Safety of woodworking machines – Tenoning machines – Part 4: Edge banding machines fed by chain(s)

EN 1218-5:2004+A1:2009-Safety of woodworking machines – Tenoning machines – Part 5: One side profiling machines with fixed table and feed rollers or feed chain

EN 12198-1:2000+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 1: General principles

EN 12198-2:2002+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 2: Radiation emission measurement procedure

EN 12198-3:2002+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 3: Reduction of radiation by attenuation or screening

EN 12203:2003+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Shoe and leather presses – Safety requirements

EN 12254:2010-Screens for laser working places – Safety requirements and testing

EN 12267:2003+A1:2010-Food processing machinery – Circular saw machines – Safety and hygiene requirements

EN 12268:2003+A1:2010-Food processing machinery – Band saw machines – Safety and hygiene requirements

EN 12301:2000+A1:2008-Plastics and rubber machines – Calenders – Safety requirements

EN 12312-1:2001+A1:2009-Aircraft ground support equipment – Specific requirements – Part 1: Passenger stairs

EN 12312-10:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 10: Container/Pallet transfer transporters

EN 12312-12:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 12: Potable water service equipment

EN 12312-13:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 13: Lavatory service equipment

EN 12312-14:2006+A1:2009-Aircraft ground support equipment – Specific requirements – Part 14: Disabled/incapacitated passenger boarding vehicles

EN 12312-15:2006+A1:2009-Aircraft ground support equipment – Specific requirements – Part 15: Baggage and equipment tractors

EN 12312-16:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 16: Air start equipment

EN 12312-17:2004+A1:2009-Aircraft ground support equipment – Specific requirements – Part 17: Air conditioning equipment

EN 12312-18:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 18: Nitrogen or Oxygen units

EN 12312-19:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions

EN 12312-2:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 2: Catering vehicles

EN 12312-20:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 20: Electrical ground power units

EN 12312-3:2003+A1:2009-Aircraft ground support equipment – Specific requirements – Part 3: Conveyor belt vehicles

EN 12312-4:2003+A1:2009-Aircraft ground support equipment – Specific requirements – Part 4: Passenger boarding bridges

EN 12312-5:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 5: Aircraft fuelling equipment

EN 12312-6:2004+A1:2009-Aircraft ground support equipment – Specific requirements – Part 6: Deicers and deicing/antiicing equipment

EN 12312-7:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 7: Air-craft movement equipment

EN 12312-8:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 8: Maintenance stairs and platforms

EN 12312-9:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 9: Container/Pallet loaders

EN 12321:2003+A1:2009-Underground mining machinery – Specification for the safety requirements of armoured face conveyors

EN 12331:2003+A2:2010-Food processing machinery – Mincing machines – Safety and hygiene requirements

EN 12336:2005+A1:2008-Tunnelling machines – Shield machines, thrust boring machines, auger boring machines, lining erection equipment – Safety requirements

EN 12348:2000+A1:2009-Core drilling machines on stand – Safety

EN 12355:2003+A1:2010-Food processing machinery – Derinding-, skinning- and membrane removal machines – Safety and hygiene requirements

EN 12385-1:2002+A1:2008-Steel wire ropes – Safety – Part 1: General requirements

EN 12385-10:2003+A1:2008-Steel wire ropes – Safety – Part 10: Spiral ropes for general structural applications

EN 12385-2:2002+A1:2008-Steel wire ropes – Safety – Part 2: Definitions, designation and classification

EN 12385-3:2004+A1:2008-Steel wire ropes – Safety – Part 3: Information for use and maintenance

EN 12385-4:2002+A1:2008-Steel wire ropes – Safety – Part 4: Stranded ropes for general lifting applications

EN 12387:2005+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Modular shoe repair equipment – Safety requirements

EN 12409:2008+A1:2011-Plastics and rubber machines – Thermoforming machines – Safety requirements

EN 12417:2001+A2:2009-Machine tools – Safety – Machining centres

EN 12418:2000+A1:2009-Masonry and stone cutting-off machines for job site – Safety

EN 12463:2004+A1:2011-Food processing machinery – Filling machines and auxiliary machines – Safety and hygiene requirements

EN 1247:2004+A1:2010-Foundry machinery – Safety requirements for ladles, pouring equipment, centrifugal casting machines, continuous and semi continuous casting machines

EN 1248:2001+A1:2009-Foundry machinery – Safety requirements for abrasive blasting equipment

EN 12505:2000+A1:2009-Food processing machinery – Centrifugal machines for processing edible oils and fats – Safety and hygiene requirements

EN 12525:2000+A2:2010-Agricultural machinery – Front loaders – Safety

EN 12545:2000+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Noise test code – Common requirements

EN 12547:1999+A1:2009-Centrifuges – Common safety requirements

EN 12549:1999+A1:2008-Acoustics – Noise test code for fastener driving tools – Engineering method

EN 12581:2005+A1:2010-Coating plants – Machinery for dip coating and electrodeposition of organic liquid coating material – Safety requirements

EN 12601:2010-Reciprocating internal combustion engine driven generating sets – Safety

EN 12621:2006+A1:2010-Machinery for the supply and circulation of coating materials under pressure – Safety requirements

EN 12622:2009-Safety of machine tools – Hydraulic press brakes

EN 12629-1:2000+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 1: Common requirements

EN 12629-2:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 2: Block making machines

EN 12629-3:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 3: Slide and turntable machines

EN 12629-4:2001+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 4:Concrete roof tile making machines

EN 12629-5-1:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-1: Pipe making machines manufacturing in the vertical axis

EN 12629-5-2:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-2: Pipe making machines manufacturing in the horizontal axis

EN 12629-5-3:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-3: Pipe prestressing machines

EN 12629-5-4:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-4: Concrete pipe coating machines

EN 12629-6:2004+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products

EN 12629-7:2004+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 7: Stationary and mobile equipment for long line manufacture of prestressed products

EN 12629-8:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)

EN 12635:2002+A1:2008-Industrial, commercial and garage doors and gates – Installation and use

EN 12643:1997+A1:2008-Earth-moving machinery – Rubber-tyred machines – Steering requirements (ISO 5010:1992 modified)

EN 12644-1:2001+A1:2008-Cranes – Information for use and testing – Part 1: Instructions

EN 12644-2:2000+A1:2008-Cranes – Information for use and testing – Part 2: Marking

EN 12649:2008+A1:2011-Concrete compactors and smoothing machines – Safety

EN 1265:1999+A1:2008-Safety of machinery – Noise test code for foundry machines and equipment

EN 12653:1999+A2:2009-Footwear, leather and imitation leather manufacturing machines – Nailing machines – Safety requirements

EN 12693:2008-Refrigerating systems and heat pumps – Safety and environmental requirements – Positive displacement refrigerant compressors

EN 12717:2001+A1:2009-Safety of machine tools – Drilling machines

EN 12733:2001+A1:2009-Agricultural and forestry machinery – Pedestrian controlled motor mowers – Safety

EN 12750:2001+A1:2009-Safety of woodworking machines – Four-sided moulding machines

EN 12753:2005+A1:2010-Thermal cleaning systems for exhaust gas from surface treatment equipment – Safety requirements

EN 12757-1:2005+A1:2010-Mixing machinery for coating materials – Safety requirements – Part 1: Mixing machinery for use in vehicle refinishing

EN 12779:2004+A1:2009-Safety of woodworking machines – Chip and dust extraction systems with fixed installation – Safety related performances and safety requirements

EN 12851:2005+A1:2010-Food processing machinery – Catering attachments for machines having an auxiliary drive hub – Safety and hygiene requirements

EN 12852:2001+A1:2010-Food processing machinery – Food processors and blenders – Safety and hygiene requirements

EN 12853:2001+A1:2010-Food processing machinery – Hand-held blenders and whisks – Safety and hygiene requirements

EN 12854:2003+A1:2010-Food processing machinery – Beam mixers – Safety and hygiene requirements

EN 12855:2003+A1:2010-Food processing machinery – Rotating bowl cutters – Safety and hygiene requirements

EN 12881-1:2005+A1:2008-Conveyor belts – Fire simulation flammability testing – Part 1: Propane burner tests

EN 12881-2:2005+A1:2008-Conveyor belts – Fire simulation flammability testing – Part 2: Large scale fire test

EN 12882:2008-Conveyor belts for general purpose use – Electrical and flammability safety requirements

EN 12921-1:2005+A1:2010-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 1: Common safety requirements

EN 12921-2:2005+A1:2008-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 2: Safety of machines using water based cleaning liquids

EN 12921-3:2005+A1:2008-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 3: Safety of machines using flammable cleaning liquids

EN 12921-4:2005+A1:2008-Machines for surface cleaning and pretreatment of industrial items using liquids and vapours – Part 4: Safety of machines using halogenated solvents

EN 12957:2001+A1:2009-Machine tools – Safety – Electro discharge machines

EN 12965:2003+A2:2009-Tractors and machinery for agriculture and forestry – Power take-off (PTO) drive shafts and their guards – Safety

EN 12978:2003+A1:2009-Industrial, commercial and garage doors and gates – Safety devices for power operated doors and gates – Requirements and test methods

EN 12981:2005+A1:2009-Coating plants – Spray booths for application of organic powder coating material – Safety requirements

EN 12984:2005+A1:2010-Food processing machinery – Portable and/or hand-guided machines and appliances with mechanically driven cutting tools – Safety and hygiene requirements

EN 1299:1997+A1:2008-Mechanical vibration and shock – Vibration isolation of machines – Information for the application of source isolation

EN 12999:2011-Cranes – Loader cranes

EN 13000:2010-Cranes – Mobile cranes

EN 13001-1:2004+A1:2009-Cranes – General design – Part 1: General principles and requirements

EN 13001-2:2011/AC:2012 (new)-EN 13001-3-1:2012 (new)

EN 13001-2:2011-Crane safety – General design – Part 2: Load actions

EN 13001-3-1:2012 (new)-Cranes – General Design – Part 3-1: Limit States and proof competence of steel structure

EN 13015:2001+A1:2008-Maintenance for lifts and escalators – Rules for maintenance instructions

EN 13019:2001+A1:2008-Machines for road surface cleaning – Safety requirements

EN 13020:2004+A1:2010-Road surface treatment machines – Safety requirements

EN 13021:2003+A1:2008-Winter service machines – Safety requirements

EN 13023:2003+A1:2010-Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment – Accuracy grades 2 and 3

EN 13035-1:2008-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 1: Storage, handling and transportation equipment inside the factory

EN 13035-11:2006+A1:2010-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 11: Drilling machines

EN 13035-2:2008-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 2: Storage, handling and transportation equipment outside the factory

EN 13035-3:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 3: Cutting machines

EN 13035-4:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 4: Tilting tables

EN 13035-5:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 5: Machines and installations for stacking and de-stacking

EN 13035-6:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 6: Machines for break-out

EN 13035-7:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 7: Cutting machines for laminated glass

EN 13035-9:2006+A1:2010-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 9: Washing installations

EN 13042-1:2007+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 1: Gob feeder

EN 13042-2:2004+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 2: Handling machines for feeding

EN 13042-3:2007+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 3: IS machines

EN 13042-5:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 5: Presses

EN 13059:2002+A1:2008-Safety of industrial trucks – Test methods for measuring vibration

EN 13102:2005+A1:2008-Ceramic machines – Safety – Loading and unloading of fine clay tiles

EN 13112:2002+A1:2009-Tannery machines – Splitting and bandknife shearing machines – Safety requirements

EN 13113:2002+A1:2010-Tannery machines – Roller coating machines – Safety requirements

EN 13114:2002+A1:2009-Tannery machines – Rotating process vessels – Safety requirements

EN 13118:2000+A1:2009-Agricultural machinery – Potato harvesting equipment – Safety

EN 13120:2009-Internal blinds – Performance requirements including safety

EN 13128:2001+A2:2009-Safety of machine tools – Milling machines (including boring machines)

EN 13135-1:2003+A1:2010-Cranes – Equipment – Part 1: Electrotechnical equipment

EN 13135-2:2004+A1:2010-Cranes – Equipment – Part 2: Non-electrotechnical equipment

EN 13140:2000+A1:2009-Agricultural machinery – Sugar beet and fodder beet harvesting equipment – Safety

EN 13155:2003+A2:2009-Cranes – Safety – Non-fixed load lifting attachments

EN 13157:2004+A1:2009-Cranes – Safety – Hand powered cranes

EN 13208:2003+A1:2010-Food processing machinery – Vegetable peelers – Safety and hygiene requirements

EN 13218:2002+A1:2008-Machine tools – Safety – Stationary grinding machines

EN 13241-1:2003+A1:2011-Industrial, commercial and garage doors and gates – Product standard – Part 1: Products without fire resistance or smoke control characteristics

EN 13288:2005+A1:2009-Food processing machinery – Bowl lifting and tilting machines – Safety and hygiene requirements

EN 13355:2004+A1:2009-Coating plants – Combined booths – Safety requirements

EN 13367:2005+A1:2008-Ceramic machines – Safety – Transfer platforms and cars

EN 13389:2005+A1:2009-Food processing machinery – Mixers with horizontal shafts – Safety and hygiene requirements

EN 13390:2002+A1:2009-Food processing machinery – Pie and tart machines – Safety and hygiene requirements

EN 13411-1:2002+A1:2008-Terminations for steel wire ropes – Safety – Part 1: Thimbles for steel wire rope slings

EN 13411-2:2001+A1:2008-Terminations for steel wire ropes – Safety – Part 2: Splicing of eyes for wire rope slings

EN 13411-3:2004+A1:2008-Terminations for steel wire ropes – Safety – Part 3: Ferrules and ferrule-securing

EN 13411-4:2011-Terminations for steel wire ropes – Safety – Part 4: Metal and resin socketing

EN 13411-5:2003+A1:2008-Terminations for steel wire ropes – Safety – Part 5: U-bolt wire rope grips

EN 13411-6:2004+A1:2008-Terminations for steel wire ropes – Safety – Part 6: Asymmetric wedge socket

EN 13411-7:2006+A1:2008-Terminations for steel wire ropes – Safety – Part 7: Symmetric wedge socket

EN 13411-8:2011-Terminations for steel wire ropes – Safety – Part 8: Swage terminals and swaging

EN 13414-1:2003+A2:2008-Steel wire rope slings – Safety – Part 1: Slings for general lifting service

EN 13414-2:2003+A2:2008-Steel wire rope slings – Safety – Part 2: Specification for information for use and maintenance to be provided by the manufacturer

EN 13414-3:2003+A1:2008-Steel wire rope slings – Safety – Part 3: Grommets and cable-laid slings

EN 13418:2004+A1:2008-Plastics and rubber machines – Winding machines for film or sheet – Safety requirements

EN 13448:2001+A1:2009-Agricultural and forestry machinery – Inter-row mowing units – Safety

EN 13457:2004+A1:2010-Footwear, leather and imitation leather goods manufacturing machines – Splitting, skiving, cutting, cementing and cement drying machines – Safety requirements

EN 13478:2001+A1:2008-Safety of machinery – Fire prevention and protection

EN 13490:2001+A1:2008-Mechanical vibration – Industrial trucks – Laboratory evaluation and specification of operator seat vibration

EN 13524:2003+A1:2009-Highway maintenance machines – Safety requirements

EN 13525:2005+A2:2009-Forestry machinery – Wood chippers – Safety

EN 13531:2001+A1:2008-Earth-moving machinery – Tip-over protection structure (TOPS) for compact excavators – Laboratory tests and performance requirements (ISO 12117:1997 modified)

EN 13534:2006+A1:2010-Food processing machinery – Curing injection machines – Safety and hygiene requirements

EN 13557:2003+A2:2008-Cranes – Controls and control stations

EN 13561:2004+A1:2008-External blinds – Performance requirements including safety

EN 13570:2005+A1:2010-Food processing machinery – Mixing machines – Safety and hygiene requirements

EN 13586:2004+A1:2008-Cranes – Access

EN 13591:2005+A1:2009-Food processing machinery – Fixed deck oven loaders – Safety and hygiene requirements

EN 13617-1:2004+A1:2009-Petrol filling stations – Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units

EN 13621:2004+A1:2010-Food processing machinery – Salad dryers – Safety and hygiene requirements

EN 13659:2004+A1:2008-Shutters – Performance requirements including safety

EN 13675:2004+A1:2010-Safety of machinery – Safety requirements for tube forming and rolling mills and their finishing line equipment

EN 13683:2003+A2:2011-Garden equipment – Integrally powered shredders/chippers – Safety

EN 13684:2004+A3:2009-Garden equipment – Pedestrian controlled lawn aerators and scarifiers – Safety

EN 13731:2007-Lifting bag systems for fire and rescue service use – Safety and performance requirements

EN 13732:2002+A2:2009-Food processing machinery – Bulk Milk Coolers on Farms – Requirements for construction, performance, suitability for use, safety and hygiene

EN 13736:2003+A1:2009-Safety of machine tools – Pneumatic presses

EN 1374:2000+A1:2010-Agricultural machinery – Silos stationary unloaders for round silos – Safety

EN 13862:2001+A1:2009-Floor cutting-off machines – Safety

EN 13870:2005+A1:2010-Food processing machinery – Chop cutting machines – Safety and hygiene requirements

EN 13871:2005+A1:2010-Food processing machinery – Cubes cutting machinery – Safety and hygiene requirements

EN 13885:2005+A1:2010-Food processing machinery – Clipping machines – Safety and hygiene requirements

EN 13886:2005+A1:2010-Food processing machinery – Cooking kettles equipped with powered stirrer and/or mixer – Safety and hygiene requirements

EN 13889:2003+A1:2008-Forged steel shackles for general lifting purposes – Dee shackles and bow shackles – Grade 6 – Safety

EN 13898:2003+A1:2009-Machine tools – Safety – Sawing machines for cold metal

EN 13951:2003+A1:2008-Liquid pumps – Safety requirements – Agrifoodstuffs equipment – Design rules to ensure hygiene in use

EN 13954:2005+A1:2010-Food processing machinery – Bread slicers – Safety and hygiene requirements

EN 13977:2011-Railway applications – Track – Safety requirements for portable machines and trolleys for construction and maintenance

EN 1398:2009-Dock levellers – Safety requirements

EN 13985:2003+A1:2009-Machine tools – Safety – Guillotine shears

EN 14010:2003+A1:2009-Safety of machinery – Equipment for power driven parking of motor vehicles – Safety and EMC requirements for design, manufacturing, erection and commissioning stages

EN 14017:2005+A2:2009-Agricultural and forestry machinery – Solid fertilizer distributors – Safety

EN 14018:2005+A1:2009-Agricultural and forestry machinery – Seed drills – Safety

EN 14033-3:2009+A1:2011-Railway applications – Track – Railbound construction and maintenance machines – Part 3: General safety requirements

EN 14043:2005+A1:2009-High rise aerial appliances for fire service use – Turntable ladders with combined movements – Safety and performance requirements and test methods

EN 14044:2005+A1:2009-High rise aerial appliances for fire service use – Turntable ladders with sequential movements – Safety and performance requirements and test methods

EN 14070:2003+A1:2009-Safety of machine tools – Transfer and special-purpose machines

EN 1417:1996+A1:2008-Plastics and rubber machines – Two roll mills – Safety requirements

EN 14238:2004+A1:2009-Cranes – Manually controlled load manipulating devices

EN 14439:2006+A2:2009-Cranes – Safety – Tower cranes

EN 14462:2005+A1:2009-Surface treatment equipment – Noise test code for surface treatment equipment including its ancillary handling equipment – Accuracy grades 2 and 3

EN 14466:2005+A1:2008-Fire-fighting pumps – Portable pumps – Safety and performance requirements, tests

EN 14492-1:2006+A1:2009-Cranes – Power driven winches and hoists – Part 1: Power driven winches

EN 14492-2:2006+A1:2009-Cranes – Power driven winches and hoists – Part 2: Power driven hoists

EN 14502-2:2005+A1:2008-Cranes – Equipment for the lifting of persons – Part 2: Elevating control stations

EN 1459:1998+A3:2012-Safety of industrial trucks – Self-propelled variable reach trucks

EN 14655:2005+A1:2010-Food processing machinery – Baguette slicers – Safety and hygiene requirements

EN 14656:2006+A1:2010-Safety of machinery – Safety requirements for extrusion presses for steel and non-ferrous metals

EN 14658:2005+A1:2010-Continuous handling equipment and systems – General safety requirements for continuous handling equipment for opencast lignite mining

EN 14673:2006+A1:2010-Safety of machinery – Safety requirements for hydraulically powered open die hot forging presses for the forging of steel and non-ferrous metals

EN 14677:2008-Safety of machinery – Secondary steelmaking – Machinery and equipment for treatment of liquid steel

EN 14681:2006+A1:2010-Safety of machinery – Safety requirements for machinery and equipment for production of steel by electric arc furnaces

EN 14710-1:2005+A2:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps without primer – Part 1: Classification, general and safety requirements

EN 14710-2:2005+A2:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps without primer – Part 2: Verification of general and safety requirements

EN 14753:2007-Safety of machinery – Safety requirements for machinery and equipment for continuous casting of steel

EN 14886:2008-Plastics and rubber machines – Bandknife cutting machines for block foams – Safety requirements

EN 14910:2007+A1:2009-Garden equipment – Walk-behind combustion engine powered trimmers – Safety

EN 1492-1:2000+A1:2008-Textile slings – Safety – Part 1: Flat woven webbing slings made of man-made fibres for general purpose use

EN 1492-2:2000+A1:2008-Textile slings – Safety – Part 2: Roundslings made of man-made fibres for general purpose use

EN 1492-4:2004+A1:2008-Textile slings – Safety – Part 4: Lifting slings for general service made from natural and man-made fibre ropes

EN 14930:2007+A1:2009-Agricultural and forestry machinery and gardening equipment – Pedestrian controlled and hand-held machines – Determination of accessibility of hot surfaces

EN 1494:2000+A1:2008-Mobile or movable jacks and associated lifting equipment

EN 1495:1997+A2:2009-Lifting platforms – Mast climbing work platforms

EN 14957:2006+A1:2010-Food processing machinery – Dishwashing machines with conveyor – Safety and hygiene requirements

EN 14958:2006+A1:2009-Food processing machinery – Machinery for grinding and processing flour and semolina – Safety and hygiene requirements

EN 14973:2006+A1:2008-Conveyor belts for use in underground installations – Electrical and flammability safety requirements

EN 14985:2012-Cranes – Slewing jib cranes

EN 15000:2008-Safety of industrial trucks – Self propelled variable reach trucks – Specification, performance and test requirements for longitudinal load moment indicators and longitudinal load moment limiters

EN 15011:2011-Cranes – Bridge and gantry cranes

EN 1501-1:2011-Refuse collection vehicles – General requirements and safety requirements – Part 1: Rear loaded refuse collection vehicles

EN 1501-2:2005+A1:2009-Refuse collection vehicles and associated lifting devices – General requirements and safety requirements – Part 2: Side loaded refuse collection vehicles

EN 1501-3:2008-Refuse collection vehicles and their associated lifting devices – General requirements and safety requirements – Part 3: Front loaded refuse collection vehicles

EN 1501-4:2007-Refuse collection vehicles and their associated lifting devices – General requirements and safety requirements – Part 4: Noise test code for refuse collection vehicles

EN 1501-5:2011-Refuse collection vehicles – General requirements and safety requirements – Part 5: Lifting devices for refuse collection vehicles

EN 15027:2007+A1:2009-Transportable wall saw and wire saw equipment for job site – Safety

EN 15056:2006+A1:2009-Cranes – Requirements for container handling spreaders

EN 15059:2009-Snow grooming equipment – Safety requirements

EN 15061:2007+A1:2008-Safety of machinery – Safety requirements for strip processing line machinery and equipment

EN 15067:2007-Plastics and rubber machines – Film converting machines for bags and sacks – Safety requirements

EN 15093:2008-Safety of Machinery – Safety requirements for hot flat rolling mills

EN 15094:2008-Safety of Machinery – Safety requirements for cold flat rolling mills

EN 15095:2007+A1:2008-Power-operated mobile racking and shelving, carousels and storage lifts – Safety requirements

EN 15162:2008-Machines and plants for mining and tooling of natural stone – Safety requirements for gang saws

EN 15163:2008-Machines and installations for the exploitation and processing of natural stone – Safety – Requirements for diamond wire saws

EN 15164:2008-Machines and plants for mining and tooling of natural stone – Safety – Requirements for chain- and belt-slotting machines

EN 15166:2008-Food processing machinery – Automatic back splitting machines of butchery carcasses – Safety and hygiene requirements

EN 1526:1997+A1:2008-Safety of industrial trucks – Additional requirements for automated functions on trucks

EN 15268:2008-Petrol filling stations – Safety requirements for the construction of submersible pump assemblies

EN 1539:2009-Dryers and ovens, in which flammable substances are released – Safety requirements

EN 1547:2001+A1:2009-Industrial thermoprocessing equipment – Noise test code for industrial thermoprocessing equipment including its ancillary handling equipment

EN 1550:1997+A1:2008-Machine-tools safety – Safety requirements for the design and construction of work holding chucks

EN 15503:2009-Garden equipment – Garden blowers, vacuums and blower/vacuums – Safety

EN 15695-1:2009-Agricultural tractors and self-propelled sprayers – Protection of the operator (driver) against hazardous substances – Part 1: Cab classification, requirements and test procedures

EN 15695-2:2009-Agricultural tractors and self-propelled sprayers – Protection of the operator (driver) against hazardous substances – Part 2: Filters, requirements and test procedures

EN 15700:2011-Safety for conveyor belts for winter sport or leisure use

EN 1570-1:2011-Safety requirements for lifting tables – Part 1: Lifting tables serving up to two fixed landings

EN 15746-2:2010+A1:2011-Railway applications – Track – Road-rail machines and associated equipment – Part 2: General safety requirements

EN 15774:2010-Food processing machinery – Machines for processing fresh and filled pasta (tagliatelle, cannelloni, ravioli, tortellini, orecchiette and gnocchi) – Safety and hygiene requirements

EN 15811:2009-Agricultural machinery – Guards for moving parts of power transmission – Guard opening with tool (ISO/TS 28923:2007 modified)

EN 15895:2011-Cartridge operated hand-held tools – Safety requirements – Fixing and hard marking tools

EN 15949:2012 (new)-Safety of machinery – Safety requirements for bar mills, structural steel mills and wire rod mills

EN 15967:2011-Determination of maximum explosion pressure and the maximum rate of pressure rise of gases and vapours

EN 15997:2011-All terrain vehicles (ATVs – Quads) – Safety requirements and test methods

EN 1612-1:1997+A1:2008-Plastics and rubber machines – Reaction moulding machines – Part 1: Safety requirements for metering and mixing units

EN 1672-2:2005+A1:2009-Food processing machinery – Basic concepts – Part 2: Hygiene requirements

EN 1673:2000+A1:2009-Food processing machinery – Rotary rack ovens – Safety and hygiene requirements

EN 1674:2000+A1:2009-Food processing machinery – Dough and pastry brakes – Safety and hygiene requirements

EN 1677-1:2000+A1:2008-Components for slings – Safety – Part 1: Forged steel components, Grade 8

EN 1677-2:2000+A1:2008-Components for slings – Safety – Part 2: Forged steel lifting hooks with latch, Grade 8

EN 1677-3:2001+A1:2008-Components for slings – Safety – Part 3: Forged steel self-locking hooks – Grade 8

EN 1677-4:2000+A1:2008-Components for slings – Safety – Part 4: Links, Grade 8

EN 1677-5:2001+A1:2008-Components for slings – Safety – Part 5: Forged steel lifting hooks with latch – Grade 4

EN 1677-6:2001+A1:2008-Components for slings – Safety – Part 6: Links – Grade 4

EN 1678:1998+A1:2010-Food processing machinery – Vegetable cutting machines – Safety and hygiene requirements

EN 1679-1:1998+A1:2011-Reciprocating internal combustion engines – Safety – Part 1: Compression ignition engines

EN 1710:2005+A1:2008-Equipment and components intended for use in potentially explosive atmospheres in underground mines

EN 1755:2000+A1:2009-Safety of industrial trucks – Operation in potentially explosive atmospheres – Use in flammable gas, vapour, mist and dust

EN 1756-1:2001+A1:2008-Tail lifts – Platform lifts for mounting on wheeled vehicles – Safety requirements – Part 1: Tail lifts for goods

EN 1756-2:2004+A1:2009-Tail lifts – Platform lifts for mounting on wheeled vehicles – Safety requirements – Part 2: Tail lifts for passengers

EN 1760-1:1997+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors

EN 1760-2:2001+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars

EN 1760-3:2004+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices

EN 1777:2010-Hydraulic platforms (HPs) for fire fighting and rescue services – Safety requirements and testing

EN 1804-1:2001+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 1: Support units and general requirements

EN 1804-2:2001+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 2: Power set legs and rams

EN 1804-3:2006+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 3: Hydraulic control systems

EN 1807:1999+A1:2009-Safety of woodworking machines – Band sawing machines

EN 1808:1999+A1:2010-Safety requirements on Suspended Access Equipment – Design calculations, stability criteria, construction – Tests

EN 1829-1:2010-High pressure water jet machines – Safety requirements – Part 1: Machines

EN 1829-2:2008-High-pressure water jet machines – Safety requirements – Part 2: Hoses, hose lines and connectors

EN 1837:1999+A1:2009-Safety of machinery – Integral lighting of machines

EN 1845:2007-Footwear manufacturing machines – Footwear moulding machines – Safety requirements

EN 1846-2:2009-Firefighting and rescue service vehicles – Part 2: Common requirements – Safety and performance

EN 1846-3:2002+A1:2008-Firefighting and rescue service vehicles – Part 3: Permanently installed equipment – Safety and performance

EN 1853:1999+A1:2009-Agricultural machinery – Trailers with tipping body – Safety

EN 1870-1:2007+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws

EN 1870-10:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines

EN 1870-11:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)

EN 1870-12:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 12: Pendulum cross-cut sawing machines

EN 1870-13:2007+A2:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 13: Horizontal beam panel sawing machines

EN 1870-14:2007+A2:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 14: Vertical panel sawing machines

EN 1870-15:2004+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 15: Multiblade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading

EN 1870-16:2005+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 16: Double mitre sawing machines for V-cutting

EN 1870-17:2007+A2:2009-Safety of woodworking machines – Circular sawing machines – Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)

EN 1870-3:2001+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches

EN 1870-4:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 4: Multiblade rip sawing machines with manual loading and/or unloading

EN 1870-5:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 5: Circular sawbenches/up-cutting cross-cut sawing machines

EN 1870-6:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading

EN 1870-7:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading

EN 1870-8:2001+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading

EN 1870-9:2000+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading

EN 1889-1:2011-Machines for underground mines – Mobile machines working underground – Safety – Part 1: Rubber tyred vehicles

EN 1889-2:2003+A1:2009-Machines for underground mines – Mobile machines working underground – Safety – Part 2: Rail locomotives

EN 1915-1:2001+A1:2009-Aircraft ground support equipment – General requirements – Part 1: Basic safety requirements

EN 1915-2:2001+A1:2009-Aircraft ground support equipment – General requirements – Part 2: Stability and strength requirements, calculations and test methods

EN 1915-3:2004+A1:2009-Aircraft ground support equipment – General requirements – Part 3: Vibration measurement methods and reduction

EN 1915-4:2004+A1:2009-Aircraft ground support equipment – General requirements – Part 4: Noise measurement methods and reduction

EN 1953:1998+A1:2009-Atomising and spraying equipment for coating materials – Safety requirements

EN 1974:1998+A1:2009-Food processing machinery – Slicing machines – Safety and hygiene requirements

EN 201:2009-Plastics and rubber machines – Injection moulding machines – Safety requirements

EN 267:2009+A1:2011-Automatic forced draught burners for liquid fuels

EN 280:2001+A2:2009-Mobile elevating work platforms – Design calculations – Stability criteria – Construction – Safety – Examinations and tests

EN 289:2004+A1:2008-Plastics and rubber machines – Presses – Safety requirements

EN 30326-1:1994-Mechanical vibration – Laboratory method for evaluating vehicle seat vibration – Part 1: Basic requirements (ISO 10326-1:1992)

EN 349:1993+A1:2008-Safety of machinery – Minimum gaps to avoid crushing of parts of the human body

EN 378-2:2008+A1:2009-Refrigerating systems and heat pumps – Safety and environmental requirements – Part 2: Design, construction, testing, marking and documentation

EN 415-1:2000+A1:2009-Packaging machines safety – Part 1: Terminology and classification of packaging machines and associated equipment

EN 415-3:1999+A1:2009-Safety of packaging machines – Part 3: Form, fill and seal machines

EN 415-5:2006+A1:2009-Safety of packaging machines – Part 5: Wrapping machines

EN 415-6:2006+A1:2009-Safety of packaging machines – Part 6: Pallet wrapping machines

EN 415-7:2006+A1:2008-Safety of packaging machines – Part 7: Group and secondary packaging machines

EN 415-8:2008-Safety of packaging machines – Part 8: Strapping machines

EN 415-9:2009-Safety of packaging machines – Part 9: Noise measurement methods for packaging machines, packaging lines and associated equipment, grade of accuracy 2 and 3

EN 422:2009-Plastics and rubber machines – Blow moulding machines – Safety requirements

EN 453:2000+A1:2009-Food processing machinery – Dough mixers – Safety and hygiene requirements

EN 454:2000+A1:2009-Food processing machinery – Planetary mixers – Safety and hygiene requirements

EN 474-1:2006+A1:2009-Earth-moving machinery – Safety – Part 1: General requirements

EN 474-10:2006+A1:2009-Earth-moving machinery – Safety – Part 10: Requirements for trenchers

EN 474-11:2006+A1:2008-Earth-moving machinery – Safety – Part 11: Requirements for earth and landfill compactors

EN 474-12:2006+A1:2008-Earth-moving machinery – Safety – Part 12: Requirements for cable excavators

EN 474-2:2006+A1:2008-Earth-moving machinery – Safety – Part 2: Requirements for tractor-dozers

EN 474-3:2006+A1:2009-Earth-moving machinery – Safety – Part 3: Requirements for loaders

EN 474-4:2006+A2:2012-Earth-moving machinery – Safety – Part 4: Requirements for backhoe loaders

EN 474-5:2006+A2:2012-Earth-moving machinery – Safety – Part 5: Requirements for hydraulic excavators

EN 474-6:2006+A1:2009-Earth-moving machinery – Safety – Part 6: Requirements for dumpers

EN 474-7:2006+A1:2009-Earth-moving machinery – Safety – Part 7: Requirements for scrapers

EN 474-8:2006+A1:2009-Earth-moving machinery – Safety – Part 8: Requirements for graders

EN 474-9:2006+A1:2009-Earth-moving machinery – Safety – Part 9: Requirements for pipelayers

EN 500-1:2006+A1:2009-Mobile road construction machinery – Safety – Part 1: Common requirements

EN 500-2:2006+A1:2008-Mobile road construction machinery – Safety – Part 2: Specific requirements for road-milling machines

EN 500-3:2006+A1:2008-Mobile road construction machinery – Safety – Part 3: Specific requirements for soil-stabilising machines and recycling machines

EN 500-4:2011-Mobile road construction machinery – Safety – Part 4: Specific requirements for compaction machines

EN 500-6:2006+A1:2008-Mobile road construction machinery – Safety – Part 6: Specific requirements for paver-finishers

EN 50223:2010-Stationary electrostatic application equipment for ignitable flock material – Safety requirements

EN 50348:2010-Stationary electrostatic application equipment for non-ignitable liquid coating material – Safety requirements

EN 50580:2012 (new)-Safety of hand-held electric motor operated tools — Particular requirements for spray guns

EN 528:2008-Rail dependent storage and retrieval equipment – Safety requirements

EN 547-1:1996+A1:2008-Safety of machinery – Human body measurements – Part 1: Principles for determining the dimensions required for openings for whole body access into machinery

EN 547-2:1996+A1:2008-Safety of machinery – Human body measurements – Part 2: Principles for determining the dimensions required for access openings

EN 547-3:1996+A1:2008-Safety of machinery – Human body measurements – Part 3: Anthropometric data

EN 574:1996+A1:2008-Safety of machinery – Two-hand control devices – Functional aspects – Principles for design

EN 60204-1:2006-Safety of machinery – Electrical equipment of machines — Part 1: General requirements

EN 60204-11:2000-Safety of machinery – Electrical equipment of machines — Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV

EN 60204-32:2008-Safety of machinery – Electrical equipment of machines — Part 32: Requirements for hoisting machines

EN 60204-33:2011-Safety of machinery – Electrical equipment of machines — Part 33: Requirements for semiconductor fabrication equipment

EN 60335-1:2012 (new)-Household and similar electrical appliances – Safety — Part 1: General requirements

EN 60335-2-67:2009-Household and similar electrical appliances – Safety — Part 2-67: Particular requirements for floor treatment and floor cleaning machines for commercial use

EN 60335-2-68:2009-Household and similar electrical appliances – Safety — Part 2-68: Particular requirements for spray extraction machines for commercial use

EN 60335-2-69:2009-Household and similar electrical appliances – Safety — Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial use

EN 60335-2-72:2009-Household and similar electrical appliances – Safety — Part 2-72: Particular requirements for automatic machines for floor treatment for commercial use

EN 60335-2-77:2010-Safety of household and similar appliances — Part 2-77: Particular requirements for pedestrian-controlled walk-behind electrically powered lawn mowers

EN 60335-2-79:2009-Household and similar electrical appliances – Safety — Part 2-79: Particular requirements for high pressure cleaners and steam cleaners

EN 60745-1:2009-Hand-held motor-operated electric tools – Safety — Part 1: General requirements

EN 60745-2-1:2010-Hand-held motor-operated electric tools – Safety — Part 2-1: Particular requirements for drills and impact drills

EN 60745-2-11:2010-Hand-held motor-operated electric tools – Safety — Part 2-11: Particular requirements for reciprocating saws (jig and sabre saws)

EN 60745-2-12:2009-Hand-held motor-operated electric tools – Safety — Part 2-12: Particular requirements for concrete vibrators

EN 60745-2-13:2009-Hand-held motor-operated electric tools – Safety — Part 2-13: Particular requirements for chain saws

EN 60745-2-14:2009-Hand-held motor-operated electric tools – Safety — Part 2-14: Particular requirements for planers

EN 60745-2-15:2009-Hand-held motor-operated electric tools – Safety — Part 2-15: Particular requirements for hedge trimmers

EN 60745-2-16:2010-Hand-held motor-operated electric tools – Safety — Part 2-16: Particular requirements for tackers

EN 60745-2-17:2010-Hand-held motor-operated electric tools – Safety — Part 2-17: Particular requirements for routers and trimmers

EN 60745-2-18:2009-Hand-held motor-operated electric tools – Safety — Part 2-18: Particular requirements for strapping tools

EN 60745-2-19:2009-Hand-held motor-operated electric tools – Safety — Part 2-19: Particular requirements for jointers

EN 60745-2-2:2010-Hand-held motor-operated electric tools – Safety — Part 2-2: Particular requirements for screwdrivers and impact wrenches

EN 60745-2-20:2009-Hand-held motor-operated electric tools – Safety — Part 2-20: Particular requirements for band saws

EN 60745-2-21:2009-Hand-held motor-operated electric tools – Safety — Part 2-21: Particular requirements for drain cleaners

EN 60745-2-22:2011-Hand-held motor-operated electric tools – Safety — Part 2-22: Particular requirements for cut-off machines

EN 60745-2-3:2011-Hand-held motor-operated electric tools – Safety — Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

EN 60745-2-4:2009-Hand-held motor-operated electric tools – Safety — Part 2-4: Particular requirements for sanders and polishers other than disk type

EN 60745-2-5:2010-Hand-held motor-operated electric tools – Safety — Part 2-5: Particular requirements for circular saws

EN 60745-2-6:2010-Hand-held motor-operated electric tools – Safety — Part 2-6: Particular requirements for hammers

EN 60745-2-8:2009-Hand-held motor-operated electric tools – Safety — Part 2-8: Particular requirements for shears and nibblers

EN 60745-2-9:2009-Hand-held motor-operated electric tools – Safety — Part 2-9: Particular requirements for tappers

EN 609-1:1999+A2:2009-Agricultural and forestry machinery – Safety of log splitters – Part 1: Wedge splitters

EN 609-2:1999+A1:2009-Agricultural and forestry machinery – Safety of log splitters – Part 2: Screw splitters

EN 61029-1:2009-Safety of transportable motor-operated electric tools — Part 1: General requirements

EN 61310-1:2008-Safety of machinery – Indication, marking and actuation — Part 1: Requirements for visual, acoustic and tactile signals

EN 61310-2:2008-Safety of machinery – Indication, marking and actuation — Part 2: Requirements for marking

EN 61310-3:2008-Safety of machinery – Indication, marking and actuation — Part 3: Requirements for the location and operation of actuators

EN 614-1:2006+A1:2009-Safety of machinery – Ergonomic design principles – Part 1: Terminology and general principles

EN 614-2:2000+A1:2008-Safety of machinery – Ergonomic design principles – Part 2: Interactions between the design of machinery and work tasks

EN 61496-1:2004-Safety of machinery – Electro-sensitive protective equipment — Part 1: General requirements and tests

EN 617:2001+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers

EN 618:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors

EN 619:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for equipment for mechanical handling of unit loads

EN 620:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for fixed belt conveyors for bulk materials

EN 62061:2005-Safety of machinery – Functional safety of safety-related electrical, electronic and programmable electronic control systems

EN 626-1:1994+A1:2008-Safety of machinery – Reduction of risks to health from hazardous substances emitted by machinery – Part 1: Principles and specifications for machinery manufacturers

EN 626-2:1996+A1:2008-Safety of machinery – Reduction of risk to health from hazardous substances emitted by machinery – Part 2: Methodology leading to verification procedures

EN 676:2003+A2:2008-Automatic forced draught burners for gaseous fuels

EN 690:1994+A1:2009-Agricultural machinery – Manure spreaders – Safety

EN 692:2005+A1:2009-Machine tools – Mechanical presses – Safety

EN 693:2001+A2:2011-Machine tools – Safety – Hydraulic presses

EN 703:2004+A1:2009-Agricultural machinery – Silage loading, mixing and/or chopping and distributing machines – Safety

EN 706:1996+A1:2009-Agricultural machinery – Vine shoot tipping machines – Safety

EN 707:1999+A1:2009-Agricultural machinery – Slurry tankers – Safety

EN 709:1997+A4:2009-Agricultural and forestry machinery – Pedestrian controlled tractors with mounted rotary cultivators, motor hoes, motor hoes with drive wheel(s) – Safety

EN 710:1997+A1:2010-Safety requirements for foundry moulding and coremaking machinery and plant associated equipment

EN 741:2000+A1:2010-Continuous handling equipment and systems – Safety requirements for systems and their components for pneumatic handling of bulk materials

EN 745:1999+A1:2009-Agricultural machinery – Rotary mowers and flail-mowers – Safety

EN 746-1:1997+A1:2009-Industrial thermoprocessing equipment – Part 1: Common safety requirements for industrial thermoprocessing equipment

EN 746-2:2010-Industrial thermoprocessing equipment – Part 2: Safety requirements for combustion and fuel handling systems

EN 746-3:1997+A1:2009-Industrial thermoprocessing equipment – Part 3: Safety requirements for the generation and use of atmosphere gases

EN 786:1996+A2:2009-Garden equipment – Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers – Mechanical safety

EN 791:1995+A1:2009-Drill rigs – Safety

EN 792-12:2000+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 12: Small circular, small oscillating and reciprocating saws

EN 792-13:2000+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 13: Fastener driving tools

EN 792-7:2001+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 7: Grinders

EN 809:1998+A1:2009-Pumps and pump units for liquids – Common safety requirements

EN 81-3:2000+A1:2008-Safety rules for the construction and installation of lifts – Part 3: Electric and hydraulic service lifts

EN 81-31:2010-Safety rules for the construction and installation of lifts – Lifts for the transport of goods only – Part 31: Accessible goods only lifts

EN 81-40:2008-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 40: Stairlifts and inclined lifting platforms intended for persons with impaired mobility

EN 81-41:2010-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 41: Vertical lifting platforms intended for use by persons with impaired mobility

EN 81-43:2009-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 43: Lifts for cranes

EN 815:1996+A2:2008-Safety of unshielded tunnel boring machines and rodless shaft boring machines for rock – Safety requirements

EN 818-1:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 1: General conditions of acceptance

EN 818-2:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 2: Medium tolerance chain for chain slings – Grade 8

EN 818-3:1999+A1:2008-Short link chain for lifting purposes – Safety – Part 3: Medium tolerance chain for chain slings – Grade 4

EN 818-4:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 4: Chain slings – Grade 8

EN 818-5:1999+A1:2008-Short link chain for lifting purposes – Safety – Part 5: Chain slings – Grade 4

EN 818-6:2000+A1:2008-Short link chain for lifting purposes – Safety – Part 6: Chain slings – Specification for information for use and maintenance to be provided by the manufacturer

EN 818-7:2002+A1:2008-Short link chain for lifting purposes – Safety – Part 7: Fine tolerance hoist chain, Grade T (Types T, DAT and DT)

EN 836:1997+A4:2011-Garden equipment – Powered lawnmowers – Safety

EN 842:1996+A1:2008-Safety of machinery – Visual danger signals – General requirements, design and testing

EN 848-1:2007+A1:2009-Safety of woodworking machines – One side moulding machines with rotating tool – Part 1: Single spindle vertical moulding machines

EN 848-2:2007+A1:2009-Safety of woodworking machines – One side moulding machines with rotating tool – Part 2: Single spindle hand fed/integrated fed routing machines

EN 848-3:2007+A2:2009-Safety of woodworking machines – One side moulding machines with rotating tools – Part 3: Numerically controlled (NC) boring and routing machines

EN 859:2007+A1:2009-Safety of woodworking machines – Hand fed surface planing machines

EN 860:2007+A1:2009-Safety of woodworking machines – One side thickness planing machines

EN 861:2007+A1:2009-Safety of woodworking machines – Surface planing and thicknessing machines

EN 869:2006+A1:2009-Safety of machinery – Safety requirements for pressure metal diecasting units

EN 894-1:1997+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 1: General principles for human interactions with displays and control actuators

EN 894-2:1997+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 2: Displays

EN 894-3:2000+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 3: Control actuators

EN 894-4:2010-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 4: Location and arrangement of displays and control actuators

EN 908:1999+A1:2009-Agricultural and forestry machinery – Reel machines for irrigation – Safety

EN 909:1998+A1:2009-Agricultural and forestry machinery – Centre pivot and moving lateral types irrigation machines – Safety

EN 930:1997+A2:2009-Footwear, leather and imitation leather goods manufacturing machines – Roughing, scouring, polishing and trimming machines – Safety requirements

EN 931:1997+A2:2009-Footwear manufacturing machines – Lasting machines – Safety requirements

EN 940:2009+A1:2012 (new)-Safety of woodworking machines – Combined woodworking machines

EN 953:1997+A1:2009-Safety of machinery – Guards – General requirements for the design and construction of fixed and movable guards

EN 972:1998+A1:2010-Tannery machines – Reciprocating roller machines – Safety requirements

EN 981:1996+A1:2008-Safety of machinery – System of auditory and visual danger and information signals

EN 996:1995+A3:2009-Piling equipment – Safety requirements

EN ISO 10218-1:2011-Robots and robotic devices – Safety requirements for industrial robots – Part 1: Robots (ISO 10218-1:2011)

EN ISO 10218-2:2011-Robots and robotic devices – Safety requirements for industrial robots – Part 2: Robot systems and integration (ISO 10218-2:2011)

EN ISO 10472-1:2008-Safety requirements for industrial laundry machinery – Part 1: Common requirements (ISO 10472-1:1997)

EN ISO 10472-2:2008-Safety requirements for industrial laundry machinery – Part 2: Washing machines and washer-extractors (ISO 10472-2:1997)

EN ISO 10472-3:2008-Safety requirements for industrial laundry machinery – Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997)

EN ISO 10472-4:2008-Safety requirements for industrial laundry machinery – Part 4: Air dryers (ISO 10472-4:1997)

EN ISO 10472-5:2008-Safety requirements for industrial laundry machinery – Part 5: Flatwork ironers, feeders and folders (ISO 10472-5:1997)

EN ISO 10472-6:2008-Safety requirements for industrial laundry machinery – Part 6: Ironing and fusing presses (ISO 10472-6:1997)

EN ISO 10517:2009-Powered hand-held hedge trimmers – Safety (ISO 10517:2009)

EN ISO 10821:2005-Industrial sewing machines – Safety requirements for sewing machines, units and systems (ISO 10821:2005)

EN ISO 11102-1:2009-Reciprocating internal combustion engines – Handle starting equipment – Part 1: Safety requirements and tests (ISO 11102-1:1997)

EN ISO 11102-2:2009-Reciprocating internal combustion engines – Handle starting equipment – Part 2: Method of testing the angle of disengagement (ISO 11102-2:1997)

EN ISO 11111-1:2009-Textile machinery – Safety requirements – Part 1: Common requirements (ISO 11111-1:2009)

EN ISO 11111-2:2005-Textile machinery – Safety requirements – Part 2: Spinning preparatory and spinning machines (ISO 11111-2:2005)

EN ISO 11111-3:2005-Textile machinery – Safety requirements – Part 3: Nonwoven machinery (ISO 11111-3:2005)

EN ISO 11111-4:2005-Textile machinery – Safety requirements – Part 4: Yarn processing, cordage and rope manufacturing machinery (ISO 11111-4:2005)

EN ISO 11111-5:2005-Textile machinery – Safety requirements – Part 5: Preparatory machinery to weaving and knitting (ISO 11111-5:2005)

EN ISO 11111-6:2005-Textile machinery – Safety requirements – Part 6: Fabric manufacturing machinery (ISO 11111-6:2005)

EN ISO 11111-7:2005-Textile machinery – Safety requirements – Part 7: Dyeing and finishing machinery (ISO 11111-7:2005)

EN ISO 11145:2008-Optics and photonics – Lasers and laser-related equipment – Vocabulary and symbols (ISO 11145:2006)

EN ISO 11148-10:2011-Hand-held non-electric power tools – Safety requirements – Part 10: Compression power tools (ISO 11148-10:2011)

EN ISO 11148-11:2011-Hand-held non-electric power tools – Safety requirements – Part 11: Nibblers and shears (ISO 11148-11:2011)

EN ISO 11148-2:2011-Hand-held non-electric power tools – Safety requirements – Part 2: Cutting-off and crimping power tools (ISO/FDIS 11148-2:2011)

EN ISO 11148-3:2010-Hand-held non-electric power tools – Safety requirements – Part 3: Drills and tappers (ISO 11148-3:2010)

EN ISO 11148-4:2010-Hand-held non-electric power tools – Safety requirements – Part 4: Non­rotary percussive power tools (ISO 11148-4:2010)

EN ISO 11148-5:2011-Hand-held non-electric power tools – Safety requirements – Part 5: Rotary percussive drills (ISO 11148-5:2011)

EN ISO 11148-6:2010-Hand-held non-electric power tools – Safety requirements – Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2010)

EN ISO 11148-8:2011-Hand-held non-electric power tools – Safety requirements – Part 8: Sanders and polishers (ISO 11148-8:2011)

EN ISO 11148-9:2011-Hand-held non-electric power tools – Safety requirements – Part 9: Die grinders (ISO 11148-9:2011)

EN ISO 11161:2007-Safety of machinery – Integrated manufacturing systems – Basic requirements (ISO 11161:2007)

EN ISO 11200:2009-Acoustics – Noise emitted by machinery and equipment – Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:1995, including Cor 1:1997)

EN ISO 11201:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)

EN ISO 11202:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)

EN ISO 11203:2009-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)

EN ISO 11204:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)

EN ISO 11205:2009-Acoustics – Noise emitted by machinery and equipment – Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity (ISO 11205:2003)

EN ISO 11252:2008-Lasers and laser-related equipment – Laser device – Minimum requirements for documentation (ISO 11252:2004)

EN ISO 11546-1:2009-Acoustics – Determination of sound insulation performances of enclosures – Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)

EN ISO 11546-2:2009-Acoustics – Determination of sound insulation performances of enclosures – Part 2: Measurements in situ (for acceptance and verification purposes) (ISO 11546-2:1995)

EN ISO 11553-1:2008-Safety of machinery – Laser processing machines – Part 1: General safety requirements (ISO 11553-1:2005)

EN ISO 11553-2:2008-Safety of machinery – Laser processing machines – Part 2: Safety requirements for hand-held laser processing devices (ISO 11553-2:2007)

EN ISO 11554:2008-Optics and photonics – Lasers and laser-related equipment – Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2006)

EN ISO 11680-1:2011-Machinery for forestry – Safety requirements and testing for pole-mounted powered pruners – Part 1: Machines fitted with an integral combustion engine (ISO 11680-1:2011)

EN ISO 11680-2:2011-Machinery for forestry – Safety requirements and testing for pole-mounted powered pruners – Part 2: Machines for use with back-pack power source (ISO 11680-2:2011)

EN ISO 11681-1:2011-Machinery for forestry – Portable chain-saw safety requirements and testing – Part 1: Chain-saws for forest service (ISO 11681-1:2011)

EN ISO 11681-2:2011-Machinery for forestry – Portable chain-saw safety requirements and testing – Part 2: Chain-saws for tree service (ISO 11681-2:2011)

EN ISO 11688-1:2009-Acoustics – Recommended practice for the design of low-noise machinery and equipment – Part 1: Planning (ISO/TR 11688-1:1995)

EN ISO 11691:2009-Acoustics – Measurement of insertion loss of ducted silencers without flow – Laboratory survey method (ISO 11691:1995)

EN ISO 11806-1:2011-Agricultural and forestry machinery – Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers – Part 1: Machines fitted with an integral combustion engine (ISO 11806-1:2011)

EN ISO 11806-2:2011-Agricultural and forestry machinery – Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers – Part 2: Machines for use with back-pack power unit (ISO 11806-2:2011)

EN ISO 11850:2011-Machinery for forestry – General safety requirements (ISO 11850:2011)

EN ISO 11957:2009-Acoustics – Determination of sound insulation performance of cabins – Laboratory and in situ measurements (ISO 11957:1996)

EN ISO 12100:2010-Safety of machinery – General principles for design – Risk assessment and risk reduction (ISO 12100:2010)

EN ISO 13732-1:2008-Ergonomics of the thermal environment – Methods for the assessment of human responses to contact with surfaces – Part 1: Hot surfaces (ISO 13732-1:2006)

EN ISO 13732-3:2008-Ergonomics of the thermal environment – Methods for the assessment of human responses to contact with surfaces – Part 3: Cold surfaces (ISO 13732-3:2005)

EN ISO 13753:2008-Mechanical vibration and shock – Hand-arm vibration – Method for measuring the vibration transmissibility of resilient materials when loaded by the hand-arm system (ISO 13753:1998)

EN ISO 13849-1:2008-Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design (ISO 13849-1:2006)

EN ISO 13849-2:2008-Safety of machinery – Safety-related parts of control systems – Part 2: Validation (ISO 13849-2:2003)

EN ISO 13850:2008-Safety of machinery – Emergency stop – Principles for design (ISO 13850:2006)

EN ISO 13855:2010-Safety of machinery – Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010)

EN ISO 13857:2008-Safety of machinery – Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)

EN ISO 14122-1:2001-Safety of machinery – Permanent means of access to machinery – Part 1: Choice of fixed means of access between two levels (ISO 14122-1:2001)

EN ISO 14122-2:2001-Safety of machinery – Permanent means of access to machinery – Part 2: Working platforms and walkways (ISO 14122-2:2001)

EN ISO 14122-3:2001-Safety of machinery – Permanent means of access to machinery – Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001)

EN ISO 14122-4:2004-Safety of machinery – Permanent means of access to machinery – Part 4: Fixed ladders (ISO 14122-4:2004)

EN ISO 14159:2008-Safety of machinery – Hygiene requirements for the design of machinery (ISO 14159:2002)

EN ISO 14314:2009-Reciprocal internal combustion engines – Recoil starting equipment – General safety requirements (ISO 14314:2004)

EN ISO 14738:2008-Safety of machinery – Anthropometric requirements for the design of workstations at machinery (ISO 14738:2002, including Cor 1:2003 and Cor 2:2005)

EN ISO 14982:2009-Agricultural and forestry machinery – Electromagnetic compatibility – Test methods and acceptance criteria (ISO 14982:1998)

EN ISO 15536-1:2008-Ergonomics – Computer manikins and body templates – Part 1: General requirements (ISO 15536-1:2005)

EN ISO 15744:2008-Hand-held non-electric power tools – Noise measurement code – Engineering method (grade 2) (ISO 15744:2002)

EN ISO 19432:2008-Building construction machinery and equipment – Portable, hand-held, internal combustion engine driven cut-off machines – Safety requirements and testing (ISO 19432:2006)

EN ISO 20361:2009-Liquid pumps and pump units – Noise test code – Grades 2 and 3 of accuracy (ISO 20361:2007)

EN ISO 20643:2008-Mechanical vibration – Hand-held and hand-guided machinery – Principles for evaluation of vibration emission (ISO 20643:2005)

EN ISO 2151:2008-Acoustics – Noise test code for compressors and vacuum pumps – Engineering method (Grade 2) (ISO 2151:2004)

EN ISO 22867:2011-Forestry and gardening machinery – Vibration test code for portable hand-held machines with internal combustion engine – Vibration at the handles (ISO 22867:2011)

EN ISO 22868:2011-Forestry and gardening machinery – Noise test code for portable hand-held machines with internal combustion engine – Engineering method (Grade 2 accuracy) (ISO 22868:2011)

EN ISO 23125:2010-Machine tools – Safety – Turning machines (ISO 23125:2010)

EN ISO 28139:2009-Agricultural and forestry machinery – Knapsack combustion-engine-driven mistblowers – Safety requirements (ISO 28139:2009)

EN ISO 2860:2008-Earth-moving machinery – Minimum access dimensions (ISO 2860:1992)

EN ISO 2867:2011-Earth-moving machinery – Access systems (ISO 2867:2011)

EN ISO 28927-1:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 1: Angle and vertical grinders (ISO 28927-1:2009)

EN ISO 28927-10:2011-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 10: Percussive drills, hammers and breakers (ISO 28927-10:2011)

EN ISO 28927-11:2011-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 11: Stone hammers (ISO 28927-11:2011)

EN ISO 28927-2:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 2: Wrenches, nutrunners and screwdrivers (ISO 28927-2:2009)

EN ISO 28927-3:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 3: Polishers and rotary, orbital and random orbital sanders (ISO 28927-3:2009)

EN ISO 28927-4:2010-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 4: Straight grinders (ISO 28927-4:2010)

EN ISO 28927-5:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 5: Drills and impact drills (ISO 28927-5:2009)

EN ISO 28927-6:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 6: Rammers (ISO 28927-6:2009)

EN ISO 28927-7:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 7: Nibblers and shears (ISO 28927-7:2009)

EN ISO 28927-8:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 8: Saws, polishing and filing machines with reciprocating action and saws with oscillating or rotating action (ISO 28927-8:2009)

EN ISO 28927-9:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 9: Scaling hammers and needle scalers (ISO 28927-9:2009)

EN ISO 3164:2008-Earth-moving machinery – Laboratory evaluations of protective structures – Specifications for deflection-limiting volume (ISO 3164:1995)

EN ISO 3266:2010-Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010)

EN ISO 3411:2007-Earth-moving machinery – Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)

EN ISO 3449:2008-Earth-moving machinery – Falling-object protective structures – Laboratory tests and performance requirements (ISO 3449:2005)

EN ISO 3450:2011-Earth-moving machinery – Wheeled or high-speed rubber-tracked machines – Performance requirements and test procedures for brake systems (ISO 3450:2011)

EN ISO 3457:2008-Earth-moving machinery – Guards – Definitions and requirements (ISO 3457:2003)

EN ISO 3471:2008-Earth-moving machinery – Roll-over protective structures – Laboratory tests and performance requirements (ISO 3471:2008)

EN ISO 3741:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for reverberation test rooms (ISO 3741:2010)

EN ISO 3743-1:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for small movable sources in reverberant fields – Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)

EN ISO 3743-2:2009-Acoustics – Determination of sound power levels of noise sources using sound pressure – Engineering methods for small, movable sources in reverberant fields – Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)

EN ISO 3744:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)

EN ISO 3745:2012 (new)-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for anechoic rooms and hemi-anechoic rooms (ISO 3745:2012)

EN ISO 3746:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)

EN ISO 3747:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010)

EN ISO 4254-1:2009-Agricultural machinery – Safety – Part 1: General requirements (ISO 4254-1:2008)

EN ISO 4254-10:2009-Agricultural machinery – Safety – Part 10: Rotary tedders and rakes (ISO 4254-10:2009)

EN ISO 4254-11:2010-Agricultural machinery – Safety – Part 11: Pick-up balers (ISO 4254-11:2010)

EN ISO 4254-5:2009-Agricultural machinery – Safety – Part 5: Power-driven soil-working machines (ISO 4254-5:2008)

EN ISO 4254-6:2009-Agricultural machinery – Safety – Part 6: Sprayers and liquid fertilizer distributors (ISO 4254-6:2009)

EN ISO 4254-7:2009-Agricultural machinery – Safety – Part 7: Combine harvesters, forage harvesters and cotton harvesters (ISO 4254-7:2008)

EN ISO 4413:2010-Hydraulic fluid power – General rules and safety requirements for systems and their components (ISO 4413:2010)

EN ISO 4414:2010-Pneumatic fluid power – General rules and safety requirements for systems and their components (ISO 4414:2010)

EN ISO 4871:2009-Acoustics – Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)

EN ISO 5136:2009-Acoustics – Determination of sound power radiated into a duct by fans and other air-moving devices – In-duct method (ISO 5136:2003)

EN ISO 5674:2009-Tractors and machinery for agriculture and forestry – Guards for power take-off (PTO) drive-shafts – Strength and wear tests and acceptance criteria (ISO 5674:2004, corrected version 2005-07-01)

EN ISO 6682:2008-Earth-moving machinery – Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989)

EN ISO 6683:2008-Earth-moving machinery – Seat belts and seat belt anchorages – Performance requirements and tests (ISO 6683:2005)

EN ISO 7096:2008-Earth-moving machinery – Laboratory evaluation of operator seat vibration (ISO 7096:2000)

EN ISO 7235:2009-Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss (ISO 7235:2003)

EN ISO 7731:2008-Ergonomics – Danger signals for public and work areas – Auditory danger signals (ISO 7731:2003)

EN ISO 8230-1:2008-Safety requirements for dry-cleaning machines – Part 1: Common safety requirements (ISO 8230-1:2008)

EN ISO 8230-2:2008-Safety requirements for dry-cleaning machines – Part 2: Machines using perchloroethylene (ISO 8230-2:2008)

EN ISO 8230-3:2008-Safety requirements for dry-cleaning machines – Part 3: Machines using combustible solvents (ISO 8230-3:2008)

EN ISO 9614-1:2009-Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 1: Measurement at discrete points (ISO 9614-1:1993)

EN ISO 9614-3:2009-Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)

EN ISO 9902-1:2001-Textile machinery – Noise test code – Part 1: Common requirements (ISO 9902-1:2001)

EN ISO 9902-2:2001-Textile machinery – Noise test code – Part 2: Spinning preparatory and spinning machinery (ISO 9902-2:2001)

EN ISO 9902-3:2001-Textile machinery – Noise test code – Part 3: Nonwoven machinery (ISO 9902-3:2001)

EN ISO 9902-4:2001-Textile machinery – Noise test code – Part 4: Yarn processing, cordage and rope manufacturing machinery (ISO 9902-4:2001)

EN ISO 9902-5:2001-Textile machinery – Noise test code – Part 5: Weaving and knitting preparatory machinery (ISO 9902-5:2001)

EN ISO 9902-6:2001-Textile machinery – Noise test code – Part 6: Fabric manufacturing machinery (ISO 9902-6:2001)

EN ISO 9902-7:2001-Textile machinery – Noise test code – Part 7: Dyeing and finishing machinery (ISO 9902-7:2001)

CE Marking – Machinery Direcitve Annex IV

23 Dec 2013 Comments
Off

이들 기계류는 고 위험군기계류로써 유럽위원회로부터 권한을 부여 받은 Notified  Body(NB)에 의해 해당되는 제품별 규격에 따라  ” EU형식시험”, 등 기계류지침 절차에 따라 인증되고 지속적 적합성을 관리 합니다.

일반적으로 원형 톱 기계, 밴드 톱 기계, 사출, 압출용 플라스틱 가공 기계, 자동차용 lift기계 및 기타 안전 기능  품목과 전도, 낙하물 보호장치가 필요한 기계류 등으로써 인체에게 심각한 손상을 가할 수 있는 기계류 입니다.

 

1. Circular saws (single- or multi-blade) for working with wood and material with similar physical characteristics or for working with meat and material with similar physical characteristics, of the following types:

1.1. sawing machinery with fixed blade(s) during cutting, having a fixed bed or support with manual feed of the workpiece or with a demountable power feed;

1.2. sawing machinery with fixed blade(s) during cutting, having a manually operated reciprocating saw-bench or carriage;

1.3 sawing machinery with fixed blade(s) during cutting, having a built-in mechanical feed device for the workpieces, with manual loading and/or unloading;

1.4. sawing machinery with movable blade(s) during cutting, having mechanical movement of the blade, with manual loading and/or unloading.

2. Hand-fed surface planing machinery for woodworking.

3. Thicknessers for one-side dressing having a built-in mechanical feed device, with manual loading and/or unloading for woodworking.

4. Band-saws with manual loading and/or unloading for working with wood and material  with similar physical characteristics or for working with meat and  material with similar physical characteristics, of the following types:

4.1. sawing machinery with fixed blade(s) during cutting, having a fixed or reciprocating-movement  bed or support for the workpiece;

4.2. sawing machinery with blade(s) assembled on a carriage with reciprocating motion.

5. Combined machinery of the types referred to in points 1 to 4 and in point 7 for  working with wood and material with similar physical characteristics.

6. Hand-fed tenoning machinery with several tool holders for woodworking.

7. Hand-fed vertical spindle moulding machinery for working with wood and material with similar physical characteristics.

8. Portable chainsaws for woodworking.

9. Presses, including press-brakes, for the cold working of metals, with manual loading and/or unloading, whose movable working parts may have a travel exceeding 6 mm and a speed exceeding 30 mm/s.

10. Injection or compression plastics-moulding machinery with manual loading or unloading.

11. Injection or compression rubber-moulding machinery with manual loading or unloading.

12. Machinery for underground working of the following types:

12.1. locomotives and brake-vans;

12.2. hydraulic-powered roof supports.

13. Manually loaded trucks for the collection of household refuse incorporating a compression mechanism.

14. Removable mechanical transmission devices including their guards.

15. Guards for removable mechanical transmission devices.

16. Vehicle servicing lifts.

17. Devices for the lifting of persons or of persons and goods involving a hazard of falling from a vertical height of more than three metres.

18. Portable cartridge-operated fixing and other impact machinery.

19. Protective devices designed to detect the presence of persons.

20. Power-operated interlocking movable guards designed to be used as safeguards in machinery referred to in points 9, 10 and 11.

21. Logic units to ensure safety functions.

22. Roll-over protective structures (ROPS).

23. Falling-object protective structures (FOPS

건설자재 CE Mark관련 EN 규격

23 Dec 2013 Comments
Off

건설자재 CE Mark관련 EN 규격

EN 1:1998-Flued oil stoves with vaporizing burners

EN 10025-1:2004Hot rolled products of structural steels – Part 1: General technical delivery conditions

EN 10088-4:2009Stainless steels – Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes

EN 10088-5:2009Stainless steels – Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes

EN 1020:2009Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products

EN 10210-1:2006Hot finished structural hollow sections of non-alloy and fine grain steels – Part 1: Technical delivery conditions

EN 10219-1:2006Cold formed welded structural hollow sections of non-alloy and fine grain steels – Part 1: Technical delivery conditions

EN 10224:2002Non-alloy steel tubes and fittings for the conveyance of aqueous liquids including water for human consumption – Technical delivery conditions

EN 10255:2004+A1:2007Non-Alloy steel tubes suitable for welding and threading – Technical delivery conditions

EN 10311:2005Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids

EN 10312:2002Welded stainless steel tubes for the conveyance of aqueous liquids including water for human consumption – Technical delivery conditions

EN 10340:2007Steel castings for structural uses

EN 10343:2009Steels for quenching and tempering for construction purposes – Technical delivery conditions

EN 1036-2:2008Glass in building – Mirrors from silver-coated float glass for internal use – Part 2: Evaluation of conformity; product standard

EN 1051-2:2007Glass in building – Glass blocks and glass pavers – Part 2: Evaluation of conformity/Product standard

EN 1057:2006+A1:2010Copper and copper alloys – Seamless, round copper tubes for water and gas in sanitary and heating applications

EN 1090-1:2009+A1:2011 (new)Execution of steel structures and aluminium structures – Part 1: Requirements for conformity assessment of structural components

EN 1096-4:2004Glass in building – Coated glass – Part 4: Evaluation of conformity/Product standard

EN 1123-1:1999Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control

EN 1124-1:1999Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control

EN 1125:2008Building hardware – Panic exit devices operated by a horizontal bar, for use on escape routes – Requirements and test methods

EN 1154:1996Building hardware – Controlled door closing devices – Requirements and test methods

EN 1155:1997Building hardware – Electrically powered hold-open devices for swing doors – Requirements and test methods

EN 1158:1997Building hardware – Door coordinator devices – Requirements and test methods

EN 1168:2005+A3:2011 (new)Precast concrete products – Hollow core slabs

EN 12004:2007Adhesives for tiles – Requirements, evaluation of conformity, classification and designation

EN 12050-1:2001Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 1: Lifting plants for wastewater containing faecal matter

EN 12050-2:2000Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 2: Lifting plants for faecal-free wastewater

EN 12050-3:2000Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 3: Lifting plants for wastewater containing faecal matter for limited applications

EN 12050-4:2000Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter

EN 12057:2004Natural stone products – Modular tiles – Requirements

EN 12058:2004Natural stone products – Slabs for floors and stairs – Requirements

EN 12094-1:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 1: Requirements and test methods for electrical automatic control and delay devices

EN 12094-10:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 10: Requirements and test methods for pressure gauges and pressure switches

EN 12094-11:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 11: Requirements and test methods for mechanical weighing devices

EN 12094-12:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 12: Requirements and test methods for pneumatic alarm devices

EN 12094-13:2001Fixed firefighting systems – Components for gas extinguishing systems – Part 13: Requirements and test methods for check valves and non-return valves

EN 12094-2:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 2: Requirements and test methods for non-electrical automatic control and delay devices

EN 12094-3:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 3: Requirements and test methods for manual triggering and stop devices

EN 12094-4:2004Fixed firefighting systems – Components for gas extinguishing systems – Part 4: Requirements and test methods for container valve assemblies and their actuators

EN 12094-5:2006Fixed firefighting systems – Components for gas extinguishing systems – Part 5: Requirements and test methods for high and low pressure selector valves and their actuators

EN 12094-6:2006Fixed firefighting systems – Components for gas extinguishing systems – Part 6: Requirements and test methods for non-electrical disable devices

EN 12094-7:2000Fixed firefighting systems – Components for gas extinguishing systems – Part 7: Requirements and test methods for nozzles for CO2 systems

EN 12094-8:2006Fixed firefighting systems – Components for gas extinguishing systems – Part 8: Requirements and test methods for connectors

EN 12094-9:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 9: Requirements and test methods for special fire detectors

EN 12101-1:2005Smoke and heat control systems – Part 1: Specification for smoke barriers

EN 12101-10:2005Smoke and heat control systems – Part 10: Power supplies

EN 12101-2:2003Smoke and heat control systems – Part 2: Specification for natural smoke and heat exhaust ventilators

EN 12101-3:2002Smoke and heat control systems – Part 3: Specification for powered smoke and heat exhaust ventilators

EN 12101-6:2005Smoke and heat control systems – Part 6: Specification for pressure differential systems – Kits

EN 12101-7:2011Smoke and heat control systems – Part 7: Smoke duct sections

EN 12101-8:2011Smoke and heat control systems – Part 8: Smoke control dampers

EN 12150-2:2004Glass in building – Thermally toughened soda lime silicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 12209:2003Building hardware – Locks and latches – Mechanically operated locks, latches and locking plates – Requirements and test methods

EN 12259-1:1999 + A1:2001Fixed firefighting systems – Components for sprinkler and water spray systems – Part 1: Sprinklers

EN 12259-2:1999Fixed firefighting systems – Components for sprinkler and water spray systems – Part 2: Wet alarm valve assemblies

EN 12259-3:2000Fixed firefighting systems – Components for automatic sprinkler and water spray systems – Part 3: Dry alarm valve assemblies

EN 12259-4:2000Fixed firefighting systems – Components for sprinkler and water spray systems – Part 4: Water motor alarms

EN 12259-5:2002Fixed firefighting systems – Components for sprinkler and water spray systems – Part 5: Water flow detectors

EN 12271:2006Surface dressing – Requirements

EN 12273:2008Slurry surfacing – Requirements

EN 12285-2:2005Workshop fabricated steel tanks – Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids

EN 12326-1:2004Slate and stone products for discontinuous roofing and cladding – Part 1: Product specification

EN 12337-2:2004Glass in building – Chemically strengthened soda lime silicate glass – Part 2: Evaluation of conformity/Product standard

EN 12352:2006Traffic control equipment – Warning and safety light devices

EN 12368:2006Traffic control equipment – Signal heads

EN 12380:2002Air admittance valves for drainage systems – Requirements, tests methods and evaluation of conformity

EN 12446:2011Chimneys – Components – Concrete outer wall elements

EN 12467:2004Fibre-cement flat sheets – Product specification and test methods

EN 12566-1:2000Small wastewater treatment systems for up to 50 PT – Part 1: Prefabricated septic tanks

EN 12566-3:2005+A1:2009Small wastewater treatment systems for up to 50 PT – Part 3: Packaged and/or site assembled domestic wastewater treatment plants

EN 12566-4:2007Small wastewater treatment systems for up to 50 PT – Part 4: Septic tanks assembled in situ from prefabricated kits

EN 12591:2009Bitumen and bituminous binders – Specifications for paving grade bitumens

EN 12620:2002+A1:2008Aggregates for concrete

EN 12676-1:2000Anti-glare systems for roads – Part 1: Performance and characteristics

EN 12737:2004+A1:2007Precast concrete products – Floor slats for livestock

EN 12764:2004+A1:2008Sanitary appliances – Specification for whirlpool baths

EN 12794:2005+A1:2007Precast concrete products – Foundation piles

EN 1279-5:2005+A2:2010Glass in building – Insulating glass units – Part 5: Evaluation of conformity

EN 12809:2001Residential independent boilers fired by solid fuel – Nominal heat output up to 50 kW – Requirements and test methods

EN 12815:2001Residential cookers fired by solid fuel – Requirements and test methods

EN 12839:2012 (new)Precast concrete products – Elements for fences

EN 12843:2004Precast concrete products – Masts and poles

EN 12859:2011Gypsum blocks – Definitions, requirements and test methods

EN 12860:2001Gypsum based adhesives for gypsum blocks – Definitions, requirements and test methods

EN 12878:2005Pigments for the colouring of building materials based on cement and/or lime – Specifications and methods of test

EN 12899-1:2007Fixed, vertical road traffic signs – Part 1: Fixed signs

EN 12899-2:2007Fixed, vertical road traffic signs – Part 2: Transilluminated traffic bollards (TTB)

EN 12899-3:2007Fixed, vertical road traffic signs – Part 3: Delineator posts and retroreflectors

EN 12951:2004Prefabricated accessories for roofing – Permanently fixed roof ladders – Product specification and test methods

EN 12966-1:2005+A1:2009Road vertical signs – Variable message traffic signs – Part 1: Product standard

EN 13024-2:2004Glass in building – Thermally toughened borosilicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 1304:2005Clay roofing tiles and fittings – Product definitions and specifications

EN 13043:2002Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas

EN 13055-1:2002Lightweight aggregates – Part 1: Lightweight aggregates for concrete, mortar and grout

EN 13055-2:2004Lightweight aggregates – Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications

EN 13063-1:2005+A1:2007Chimneys – System chimneys with clay/ceramic flue liners – Part 1: Requirements and test methods for sootfire resistance

EN 13063-2:2005+A1:2007Chimneys – System chimneys with clay/ceramic flue liners – Part 2: Requirements and test methods under wet conditions

EN 13063-3:2007Chimneys – System chimneys with clay/ceramic flue liners – Part 3: Requirements and test methods for air flue system chimneys

EN 13069:2005Chimneys – Clay/ceramic outer walls for system chimneys – Requirements and test methods

EN 13084-5:2005Free-standing chimneys – Part 5: Material for brick liners – Product specifications

EN 13084-7:2005Free-standing chimneys – Part 7: Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and steel liners

EN 13101:2002Steps for underground man entry chambers – Requirements, marking, testing and evaluation of conformity

EN 13108-1:2006Bituminous mixtures – Material specifications – Part 1: Asphalt Concrete

EN 13108-2:2006Bituminous mixtures – Material specifications – Part 2: Asphalt Concrete for very thin layers

EN 13108-3:2006Bituminous mixtures – Material specifications – Part 3: Soft Asphalt

EN 13108-4:2006Bituminous mixtures – Material specifications – Part 4: Hot Rolled Asphalt

EN 13108-5:2006Bituminous mixtures – Material specifications – Part 5: Stone Mastic Asphalt

EN 13108-6:2006Bituminous mixtures – Material specifications – Part 6: Mastic Asphalt

EN 13108-7:2006Bituminous mixtures – Material specifications – Part 7: Porous Asphalt

EN 13139:2002Aggregates for mortar

EN 13160-1:2003Leak detection systems – Part 1: General principles

EN 13162:2008Thermal insulation products for buildings – Factory made mineral wool (MW) products – Specification

EN 13163:2008Thermal insulation products for buildings – Factory made products of expanded polystyrene (EPS) – Specification

EN 13164:2008Thermal insulation products for buildings – Factory made products of extruded polystyrene foam (XPS) – Specification

EN 13165:2008Thermal insulation products for buildings – Factory made rigid polyurethane foam (PUR) products – Specification

EN 13166:2008Thermal insulation products for buildings – Factory made products of phenolic foam (PF) – Specification

EN 13167:2008Thermal insulation products for buildings – Factory made cellular glass (CG) products – Specification

EN 13168:2008Thermal insulation products for buildings – Factory made wood wool (WW) products – Specification

EN 13169:2008Thermal insulation products for buildings – Factory made products of expanded perlite (EPB) – Specification

EN 13170:2008Thermal insulation products for buildings – Factory made products of expanded cork (ICB) – Specification

EN 13171:2008Thermal insulating products for buildings – Factory made wood fibre (WF) products – Specification

EN 1317-5:2007+A2:2012 (new)Road restraint systems – Part 5: Product requirements and evaluation of conformity for vehicle restraint systems

EN 1319:2009Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

EN 13224:2011 (new)Precast concrete products – Ribbed floor elements

EN 13225:2004Precast concrete products – Linear structural elements

EN 13229:2001Inset appliances including open fires fired by solid fuels – Requirements and test methods

EN 13240:2001Roomheaters fired by solid fuel – Requirements and test methods

EN 13241-1:2003+A1:2011Industrial, commercial and garage doors and gates – Product standard – Part 1: Products without fire resistance or smoke control characteristics

EN 13242:2002+A1:2007Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction

EN 13245-2:2008Plastics – Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications – Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes

EN 13249:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of roads and other trafficked areas (excluding railways and asphalt inclusion)

EN 13250:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of railways

EN 13251:2000Geotextiles and geotextile-related products – Characteristics required for use in earthworks, foundations and retaining structures

EN 13252:2000Geotextiles and geotextile-related products – Characteristics required for use in drainage systems

EN 13253:2000Geotextiles and geotextile-related products – Characteristics required for use in erosion control works (coastal protection, bank revetments)

EN 13254:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of reservoirs and dams

EN 13255:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of canals

EN 13256:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of tunnels and underground structures

EN 13257:2000Geotextiles and geotextile-related products – Characteristics required for use in solid waste disposals

EN 13263-1:2005+A1:2009Silica fume for concrete – Part 1: Definitions, requirements and conformity criteria

EN 13265:2000Geotextiles and geotextile-related products – Characteristics required for use in liquid waste containment projects

EN 13279-1:2008Gypsum binders and gypsum plasters – Part 1: Definitions and requirements

EN 13310:2003Kitchen sinks – Functional requirements and test methods

EN 13341:2005+A1:2011Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels – Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of nionically polymerized polyamide 6 – Requirements and test methods

EN 13361:2004Geosynthetic barriers – Characteristics required for use in the construction of reservoirs and dams

EN 13362:2005Geosynthetic Barriers – Characteristics required for use in the construction of canals

EN 1337-3:2005Structural bearings – Part 3: Elastomeric bearings

EN 1337-4:2004Structural bearings – Part 4: Roller bearings

EN 1337-5:2005Structural bearings – Part 5: Pot bearings

EN 1337-6:2004Structural bearings – Part 6: Rocker bearings

EN 1337-7:2004Structural bearings – Part 7: Spherical and cylindrical PTFE bearings

EN 1337-8:2007Structural bearings – Part 8: Guide Bearings and Restraint Bearings

EN 1338:2003Concrete paving blocks – Requirements and test methods

EN 13383-1:2002Armourstone – Part 1: Specification

EN 1339:2003Concrete paving flags – Requirements and test methods

EN 1340:2003Concrete kerb units – Requirements and test methods

EN 13407:2006Wall-hung urinals – Functional requirements and test methods

EN 1341:2001Slabs of natural stone for external paving – Requirements and test methods

EN 1342:2001Setts of natural stone for external paving – Requirements and test methods

EN 1343:2001Kerbs of natural stone for external paving – Requirements and test methods

EN 1344:2002Clay pavers – Requirements and test methods EN 13450:2002Aggregates for railway ballast

EN 13454-1:2004Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate – Part 1: Definitions and requirements

EN 13479:2004Welding consumables – General product standard for filler metals and fluxes for fusion welding of metallic materials

EN 13491:2004Geosynthetic barriers – Characteristics required for use as a fluid barrier in the construction of tunnels and underground structures

EN 13492:2004Geosynthetic barriers – Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment

EN 13493:2005Geosynthetic barriers – Characteristics required for use in the construction of solid waste storage and disposal sites

EN 13502:2002Chimneys – Requirements and test methods for clay/ceramic flue terminals

EN 13561:2004+A1:2008External blinds – Performance requirements including safety

EN 13564-1:2002Anti-flooding devices for buildings – Part 1: Requirements

EN 13616:2004Overfill prevention devices for static tanks for liquid petroleum fuels

EN 13658-1:2005Metal lath and beads – Definitions, requirements and test methods – Part 1: Internal plastering

EN 13658-2:2005Metal lath and beads – Definitions, requirements and test methods – Part 2: External rendering

EN 13659:2004+A1:2008Shutters – Performance requirements including safety

EN 13693:2004+A1:2009Precast concrete products – Special roof elements

EN 13707:2004+A2:2009Flexible sheets for waterproofing – Reinforced bitumen sheets for roof waterproofing – Definitions and characteristics

EN 13747:2005+A2:2010Precast concrete products – Floor plates for floor systems

EN 13748-1:2004Terrazzo tiles – Part 1: Terrazzo tiles for internal use

EN 13748-2:2004Terrazzo tiles – Part 2: Terrazzo tiles for external use

EN 13808:2005Bitumen and bituminous binders – Framework for specifying cationic bituminous emulsions

EN 13813:2002Screed material and floor screeds – Screed material – Properties and requirements

EN 13815:2006Fibrous gypsum plaster casts – Definitions, requirements and test methods

EN 13830:2003Curtain walling – Product standard

EN 13859-1:2010Flexible sheets for waterproofing – Definitions and characteristics of underlays – Part 1: Underlays for discontinuous roofing

EN 13859-2:2010Flexible sheets for waterproofing – Definitions and characteristics of underlays – Part 2: Underlays for walls

EN 13877-3:2004Concrete pavements – Part 3: Specifications for dowels to be used in concrete pavements

EN 13915:2007Prefabricated gypsum plasterboard panels with a cellular paperboard core – Definitions, requirements and test methods

EN 13924:2006Bitumen and bituminous binders – Specifications for hard paving grade bitumens

EN 13950:2005Gypsum plasterboard thermal/acoustic insulation composite panels – Definitions, requirements and test methods

EN 13956:2005Flexible sheet for waterproofing – Plastic and rubber sheets for roof waterproofing – Definitions and characteristics

EN 13963:2005Jointing materials for gypsum plasterboards – Definitions, requirements and test methods

EN 13964:2004Suspended ceilings – Requirements and test methods

EN 13967:2004Flexible sheets for waterproofing – Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet – Definitions and characteristics

EN 13969:2004Flexible sheets for waterproofing – Bitumen damp proof sheets including bitumen basement tanking sheets – Definitions and characteristics

EN 13970:2004Flexible sheets for waterproofing – Bitumen water vapour control layers – Definitions and characteristics

EN 13978-1:2005Precast concrete products – Precast concrete garages – Part 1: Requirements for reinforced garages monolithic or consisting of single sections with room dimensions

EN 13984:2004Flexible sheets for waterproofing – Plastic and rubber vapour control layers – Definitions and characteristics

EN 13986:2004Wood-based panels for use in construction – Characteristics, evaluation of conformity and marking

EN 14016-1:2004Binders for magnesite screeds – Caustic magnesia and magnesium chloride – Part 1: Definitions, requirements

EN 14023:2010Bitumen and bituminous binders – Specification framework for polymer modified bitumens

EN 14037-1:2003Ceiling mounted radiant panels supplied with water at temperature below 120 °C – Part 1: Technical specifications and requirements

EN 14041:2004Resilient, textile and laminate floor coverings – Essential characteristics

EN 14055:2010WC and urinal flushing cisterns

EN 14063-1:2004Thermal insulation products for buildings – In-situ formed expanded clay lightweight aggregate products – Part 1: Specification for the loose-fill products before installation

EN 14064-1:2010Thermal insulation products for buildings – In-situ formed loose-fill mineral wool (MW) products – Part 1: Specification for the loose-fill products before installation

EN 14080:2005Timber structures – Glued laminated timber – Requirements

EN 14081-1:2005+A1:2011Timber structures – Strength graded structural timber with rectangular cross section – Part 1: General requirements

EN 14178-2:2004Glass in building – Basic alkaline earth silicate glass products – Part 2: Evaluation of conformity/Product standard

EN 14179-2:2005Glass in building – Heat soaked thermally toughened soda lime silicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 14188-1:2004Joint fillers and sealants – Part 1: Specifications for hot applied sealants

EN 14188-2:2004Joint fillers and sealants – Part 2: Specifications for cold applied sealants

EN 14188-3:2006Joint fillers and sealants – Part 3: Specifications for preformed joint seals

EN 14190:2005Gypsum plasterboard products from reprocessing – Definitions, requirements and test methods

EN 14195:2005Metal framing components for gypsum plasterboard systems – Definitions, requirements and test methods

EN 14209:2005Preformed plasterboard cornices – Definitions, requirements and test methods

EN 14216:2004Cement – Composition, specifications and conformity criteria for very low heat special cements

EN 14229:2010Structural timber – Wood poles for overhead lines

EN 1423:2012 (new)Road marking materials – Drop on materials – Glass beads, antiskid aggregates and mixtures of the two

EN 14246:2006Gypsum elements for suspended ceilings – Definitions, requirements and test methods

EN 14250:2010Timber structures – Product requirements for prefabricated structural members assembled with punched metal plate fasteners

EN 14296:2005Sanitary appliances – Communal washing troughs

EN 14303:2009Thermal insulation products for building equipment and industrial installations – Factory made mineral wool (MW) products – Specification

EN 14304:2009Thermal insulation products for building equipment and industrial installations – Factory made flexible elastomeric foam (FEF) products – Specification

EN 14305:2009Thermal insulation products for building equipment and industrial installations – Factory made cellular glass (CG) products – Specification

EN 14306:2009Thermal insulation products for building equipment and industrial installations – Factory made calcium silicate (CS) products – Specification

EN 14307:2009Thermal insulation products for building equipment and industrial installations – Factory made extruded polystyrene foam (XPS) products – Specification

EN 14308:2009Thermal insulation products for building equipment and industrial installations – Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products – Specification

EN 14309:2009Thermal insulation products for building equipment and industrial installations – Factory made products of expanded polystyrene (EPS) – Specification

EN 14313:2009Thermal insulation products for building equipment and industrial installations – Factory made polyethylene foam (PEF) products – Specification

EN 14314:2009Thermal insulation products for building equipment and industrial installations – Factory made phenolic foam (PF) products – Specification

EN 14316-1:2004Thermal insulation products for buildings – In-situ thermal insulation formed from expanded perlite (EP) products – Part 1: Specification for bonded and loose-fill products before installation

EN 14317-1:2004Thermal insulation products for buildings – In-situ thermal insulation formed from exfoliated vermiculite (EV) products – Part 1: Specification for bonded and loose-fill products before installation

EN 14321-2:2005Glass in building – Thermally toughened alkaline earth silicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 1433:2002Drainage channels for vehicular and pedestrian areas – Classification, design and testing requirements, marking and evaluation of conformity

EN 14339:2005Underground fire hydrants

EN 14342:2005+A1:2008Wood flooring – Characteristics, evaluation of conformity and marking

EN 14351-1:2006+A1:2010Windows and doors – Product standard, performance characteristics – Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics

EN 14353:2007+A1:2010Metal beads and feature profiles for use with gypsum plasterboards – Definitions, requirements and test methods

EN 14374:2004Timber structures – Structural laminated veneer lumber – Requirements

EN 14384:2005Pillar fire hydrants

EN 14388:2005Road traffic noise reducing devices – Specifications

EN 14396:2004Fixed ladders for manholes

EN 14399-1:2005High-strength structural bolting assemblies for preloading – Part 1: General requirements

EN 14411:2006Ceramic tiles – Definitions, classification, characteristics and marking

EN 14428:2004+A1:2008Shower enclosures – Functional requirements and test methods

EN 14449:2005Glass in building – Laminated glass and laminated safety glass – Evaluation of conformity/Product standard

EN 14471:2005Chimneys – System chimneys with plastic flue liners – Requirements and test methods

EN 14496:2005Gypsum based adhesives for thermal/acoustic insulation composite panels and plasterboards – Definitions, requirements and test methods

EN 14509:2006Self-supporting double skin metal faced insulating panels – Factory made products – Specifications

EN 14516:2006+A1:2010Baths for domestic purposes

EN 14527:2006+A1:2010Shower trays for domestic purposes

EN 14528:2007Bidets – Functional requirements and test methods

EN 14545:2008Timber structures – Connectors – Requirements

EN 14566:2008+A1:2009Mechanical fasteners for gypsum plasterboard systems – Definitions, requirements and test methods

EN 1457-1:2012 (new)Chimneys – Clay/ceramic flue liners – Part 1: Flue liners operating under dry conditions – Requirements and test methods

EN 1457-2:2012 (new)Chimneys – Clay/ceramic flue liners – Part 2: Flue liners operating under wet conditions – Requirements and test methods

EN 14592:2008Timber structures – Dowel-type fasteners – Requirements

EN 14604:2005Smoke alarm devices

EN 1463-1:2009Road marking materials – Retroreflecting road studs – Part 1: Initial performance requirements

EN 14647:2005Calcium aluminate cement – Composition, specifications and conformity criteria

EN 14680:2006Adhesives for non-pressure thermoplastic piping systems – Specifications

EN 14688:2006Sanitary appliances – Wash basins – Functional requirements and test methods

EN 1469:2004Natural stone products – Slabs for cladding – Requirements

EN 14695:2010Flexible sheets for waterproofing – Reinforced bitumen sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete – Definitions and characteristics

EN 14716:2004Stretched ceilings – Requirements and test methods

EN 14782:2006Self-supporting metal sheet for roofing, external cladding and internal lining – Product specification and requirements

EN 14783:2006Fully supported metal sheet and strip for roofing, external cladding and internal lining – Product specification and requirements

EN 14785:2006Residential space heating appliances fired by wood pellets – Requirements and test methods

EN 14800:2007Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels

EN 14814:2007Adhesives for thermoplastic piping systems for fluids under pressure – Specifications

EN 14843:2007Precast concrete products – Stairs

EN 14844:2006+A2:2011 (new)Precast concrete products – Box culverts

EN 14846:2008Building hardware – Locks and latches – Electromechanically operated locks and striking plates – Requirements and test methods

EN 14889-1:2006Fibres for concrete – Part 1: Steel fibres – Definitions, specifications and conformity

EN 14889-2:2006Fibres for concrete – Part 2: Polymer fibres – Definitions, specifications and conformity

EN 14904:2006Surfaces for sports areas – Indoor surfaces for multi-sports use – Specification

EN 14909:2006Flexible sheets for waterproofing – Plastic and rubber damp proof courses – Definitions and characteristics

EN 14915:2006Solid wood panelling and cladding – Characteristics, evaluation of conformity and marking

EN 14933:2007Thermal insulation and light weight fill products for civil engineering applications – Factory made products of expanded polystyrene (EPS) – Specification

EN 14934:2007Thermal insulation and light weight fill products for civil engineering applications – Factory made products of extruded polystyrene foam (XPS) – Specification

EN 14963:2006Roof coverings – Continuous rooflights of plastics with or without upstands – Classification, requirements and test methods

EN 14964:2006Rigid underlays for discontinuous roofing – Definitions and characteristics

EN 14967:2006Flexible sheets for waterproofing – Bitumen damp proof courses – Definitions and characteristics

EN 14989-1:2007Chimneys – Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications – Part 1: Vertical air/flue terminals for C6-type appliances

EN 14989-2:2007Chimneys – Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications – Part 2: Flue and air supply ducts for room sealed appliances

EN 14991:2007Precast concrete products – Foundation elements

EN 14992:2007Precast concrete products – Wall elements

EN 15037-1:2008Precast concrete products – Beam-and-block floor systems – Part 1: Beams

EN 15037-2:2009+A1:2011Precast concrete products – Beam-and-block floor systems – Part 2: Concrete blocks

EN 15037-3:2009+A1:2011Precast concrete products – Beam-and-block floor systems – Part 3: Clay blocks

EN 15037-4:2010Precast concrete products – Beam-and-block floor systems – Part 4: Expanded polystyrene blocks

EN 1504-2:2004Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 2: Surface protection systems for concrete

EN 1504-3:2005Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 3: Structural and non-structural repair

EN 1504-4:2004Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 4: Structural bonding

EN 1504-5:2004Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 5: Concrete injection

EN 1504-6:2006Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 6: Anchoring of reinforcing steel bar

EN 1504-7:2006Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 7: Reinforcement corrosion protection

EN 15048-1:2007Non-preloaded structural bolting assemblies – Part 1: General requirements

EN 15050:2007+A1:2012 (new)Precast concrete products – Bridge elements

EN 15069:2008Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel

EN 15088:2005Aluminium and aluminium alloys – Structural products for construction works – Technical conditions for inspection and delivery

EN 15102:2007+A1:2011 (new)Decorative wall coverings – Roll and panel form

EN 15129:2009Anti-seismic devices

EN 15167-1:2006Ground granulated blast furnace slag for use in concrete, mortar and grout – Part 1: Definitions, specifications and conformity criteria

EN 1520:2011Prefabricated reinforced components of lightweight aggregate concrete with open structure with structural or non-structural reinforcement

EN 15250:2007Slow heat release appliances fired by solid fuel – Requirements and test methods

EN 15258:2008-Precast concrete products – Retaining wall elements

EN 15274:2007General purpose adhesives for structural assembly – Requirements and test methods

EN 15275:2007Structural adhesives – Characterisation of anaerobic adhesives for co-axial metallic assembly in building and civil engineering structures

EN 15283-1:2008+A1:2009Gypsum boards with fibrous reinforcement – Definitions, requirements and test methods – Part 1: Gypsum boards with mat reinforcement

EN 15283-2:2008+A1:2009Gypsum boards with fibrous reinforcement – Definitions, requirements and test methods – Part 2: Gypsum fibre boards

EN 15285:2008Agglomerated stone – Modular tiles for flooring and stairs (internal and external)

EN 15322:2009Bitumen and bituminous binders – Framework for specifying cut-back and fluxed bituminous binders

EN 15368:2008+A1:2010Hydraulic binder for non-structural applications – Definition, specifications and conformity criteria

EN 15381:2008Geotextiles and geotextile-related products – Characteristics required for use in pavements and asphalt overlays

EN 15382:2008Geosynthetic barriers – Characteristics required for use in transportation infrastructure

EN 15435:2008Precast concrete products – Normal weight and lightweight concrete shuttering blocks – Product properties and performance

EN 15498:2008Precast concrete products – Wood-chip concrete shuttering blocks – Product properties and performance

EN 15599-1:2010Thermal insulation products for building equipment and industrial installations – In-situ thermal insulation formed from expanded perlite (EP) products – Part 1: Specification for bonded and loose-fill products before installation

EN 15600-1:2010Thermal insulation products for building equipment and industrial installations – In-situ thermal insulation formed from exfoliated vermiculite (EV) products – Part 1: Specification for bonded and loose-fill products before installation

EN 15650:2010Ventilation for buildings – Fire dampers

EN 15743:2010Supersulfated cement – Composition, specifications and conformity criteria

EN 15821:2010Multi-firing sauna stoves fired by natural wood logs – Requirements and test methods

EN 15824:2009Specifications for external renders and internal plasters based on organic binders

EN 1748-1-2:2004Glass in building – Special basic products – Borosilicate glasses – Part 1-2: Evaluation of conformity/Product standard

EN 1748-2-2:2004Glass in building – Special basic products – Glass ceramics – Part 2-2: Evaluation of conformity/Product standard

EN 179:2008Building hardware – Emergency exit devices operated by a lever handle or push pad, for use on escape routes – Requirements and test methods

EN 1806:2006Chimneys – Clay/ceramic flue blocks for single wall chimneys – Requirements and test methods

EN 1825-1:2004Grease separators – Part 1: Principles of design, performance and testing, marking and quality control

EN 1856-1:2009Chimneys – Requirements for metal chimneys – Part 1: System chimney products

EN 1856-2:2009Chimneys – Requirements for metal chimneys – Part 2: Metal flue liners and connecting flue pipes

EN 1857:2010Chimneys – Components – Concrete flue liners

EN 1858:2008+A1:2011Chimneys – Components – Concrete flue blocks

EN 1863-2:2004Glass in building – Heat strengthened soda lime silicate glass – Part 2: Evaluation of conformity/Product standard

EN 1873:2005Prefabricated accessories for roofing – Individual roof lights of plastics – Product specification and test methods

EN 1916:2002Concrete pipes and fittings, unreinforced, steel fibre and reinforced

EN 1917:2002Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

EN 1935:2002Building hardware – Single-axis hinges – Requirements and test methods

EN 197-1:2011 (new)Cement – Part 1: Composition, specifications and conformity criteria for common cements

EN 295-10:2005Vitrified clay pipes and fittings and pipe joints for drains and sewers – Part 10: Performance requirements

EN 331:1998Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings

EN 40-4:2005Lighting columns – Part 4: Requirements for reinforced and prestressed concrete lighting columns

EN 40-5:2002Lighting columns – Part 5: Requirements for steel lighting columns

EN 40-6:2002Lighting columns – Part 6: Requirements for aluminium lighting columns

EN 413-1:2011Masonry cement – Part 1: Composition, specifications and conformity criteria

EN 416-1:2009Single burner gas-fired overhead radiant tube heaters for non-domestic use – Part 1: Safety

EN 438-7:2005High-pressure decorative laminates (HPL) – Sheets based on thermosetting resins (Usually called Laminates) – Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes

EN 442-1:1995Radiators and convectors – Part 1: Technical specifications and requirements

EN 450-1:2005+A1:2007Fly ash for concrete – Part 1: Definition, specifications and conformity criteria

EN 459-1:2010Building lime – Part 1: Definitions, specifications and conformity criteria

EN 490:2011 (new)Concrete roofing tiles and fittings for roof covering and wall cladding – Product specifications

EN 492:2004Fibre-cement slates and fittings – Product specification and test methods

EN 494:2004+A3:2007Fibre-cement profiled sheets and fittings – Product specification and test methods

EN 516:2006Prefabricated accessories for roofing – Installations for roof access – Walkways, treads and steps

EN 517:2006Prefabricated accessories for roofing – Roof safety hooks

EN 520:2004+A1:2009Gypsum plasterboards – Definitions, requirements and test methods

EN 523:2003Steel strip sheaths for prestressing tendons – Terminology, requirements, quality control

EN 534:2006+A1:2010Corrugated bitumen sheets – Product specification and test methods

EN 54-10:2002Fire detection and fire alarm systems – Part 10: Flame detectors – Point detectors

EN 54-11:2001Fire detection and fire alarm systems – Part 11: Manual call points

EN 54-12:2002Fire detection and fire alarm systems – Part 12: Smoke detectors – Line detectors using an optical light beam

EN 54-16:2008Fire detection and fire alarm systems – Part 16: Voice alarm control and indicating equipment

EN 54-17:2005Fire detection and fire alarm systems – Part 17: Short-circuit isolators

EN 54-18:2005Fire detection and fire alarm systems – Part 18: Input/output devices

EN 54-2:1997Fire detection and fire alarm systems – Part 2: Control and indicating equipment

EN 54-20:2006Fire detection and fire alarm systems – Part 20: Aspirating smoke detectors

EN 54-21:2006Fire detection and fire alarm systems – Part 21: Alarm transmission and fault warning routing equipment

EN 54-23:2010Fire detection and fire alarm systems – Part 23: Fire alarm devices – Visual alarm devices

EN 54-24:2008Fire detection and fire alarm systems – Part 24: Components of voice alarm systems – Loudspeakers

EN 54-25:2008Fire detection and fire alarm systems – Part 25: Components using radio links

EN 54-3:2001Fire detection and fire alarm systems – Part 3: Fire alarm devices – Sounders

EN 54-4:1997Fire detection and fire alarm systems – Part 4: Power supply equipment

EN 544:2011Bitumen shingles with mineral and/or synthetic reinforcements – Product specification and test methods

EN 54-5:2000Fire detection and fire alarm systems – Part 5: Heat detectors – Point detectors

EN 54-7:2000Fire detection and fire alarm systems – Part 7: Smoke detectors – Point detectors using scattered light, transmitted light or ionization

EN 572-9:2004Glass in building – Basic soda lime silicate glass products – Part 9: Evaluation of conformity/Product standard

EN 588-2:2001Fibre cement pipes for drains and sewers – Part 2: Manholes and inspection chambers

EN 598:2007+A1:2009Ductile iron pipes, fittings, accessories and their joints for sewerage applications – Requirements and test methods

EN 621:2009Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products

EN 671-1:2001Fixed firefighting systems – Hose systems – Part 1: Hose reels with semi-rigid hose

EN 671-2:2001Fixed firefighting systems – Hose systems – Part 2: Hose systems with lay-flat hose

EN 681-1:1996Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 1: Vulcanized rubber

EN 681-2:2000Elastomeric Seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 2: Thermoplastic elastomers

EN 681-3:2000Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 3: Cellular materials of vulcanized rubber

EN 681-4:2000Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 4: Cast polyurethane sealing elements

EN 682:2002Elastomeric Seals – Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

EN 771-1:2011Specification for masonry units – Part 1: Clay masonry units

EN 771-2:2011Specification for masonry units – Part 2: Calcium silicate masonry units

EN 771-3:2011Specification for masonry units – Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)

EN 771-4:2011Specification for masonry units – Part 4: Autoclaved aerated concrete masonry units

EN 771-5:2011Specification for masonry units – Part 5: Manufactured stone masonry units

EN 771-6:2011Specification for masonry units – Part 6: Natural stone masonry units

EN 777-1:2009Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use – Part 1: System D – Safety

EN 777-2:2009Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use – Part 2: System E – Safety

EN 777-3:2009Multi-burner gas-fired overhead radiant tube heater systems for non domestic use – Part 3: System F – Safety

EN 777-4:2009Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use – Part 4: System H – Safety

EN 778:2009Domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 70 kW, without a fan to assist transportation of combustion air and/or combustion products

EN 845-1:2003+A1:2008Specification for ancillary components for masonry – Part 1: Ties, tension straps, hangers and brackets

EN 845-2:2003Specification for ancillary components for masonry – Part 2: Lintels

EN 845-3:2003+A1:2008Specification for ancillary components for masonry – Part 3: Bed joint reinforcement of steel meshwork

EN 858-1:2002Separator systems for light liquids (e.g. oil and petrol) – Part 1: Principles of product design, performance and testing, marking and quality control

EN 877:1999Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings – Requirements, test methods and quality assurance

EN 934-2:2009Admixtures for concrete, mortar and grout – Part 2: Concrete admixtures – Definitions, requirements, conformity, marking and labelling

EN 934-3:2009Admixtures for concrete, mortar and grout – Part 3: Admixtures for masonry mortar – Definitions, requirements, conformity and marking and labelling

EN 934-4:2009Admixtures for concrete, mortar and grout – Part 4: Admixtures for grout for prestressing tendons – Definitions, requirements, conformity, marking and labelling

EN 934-5:2007Admixtures for concrete, mortar and grout – Part 5: Admixtures for sprayed concrete – Definitions, requirements, conformity, marking and labelling

EN 969:2009Ductile iron pipes, fittings, accessories and their joints for gas pipelines – Requirements and test methods

EN 997:2012 (new)WC pans and WC suites with integral trap

EN 998-1:2010Specification for mortar for masonry – Part 1: Rendering and plastering mortar

EN 998-2:2010Specification for mortar for masonry – Part 2: Masonry mortar

미국철도협회(AAR) 관련 규격

23 Dec 2013 Comments
Off

- 아래는 미국철도협회(AAR) 관련 규격 목록입니다.

Data Management and Communications CD M1585CD
Data Management and Communications M1585
Systems Architecture and Concepts of Operation CD M1500CD
Systems Architecture and Concepts of Operation M1500
Open Top Trailer and Container for Rail Transport M0502
Open Top Trailer and Containers for Rail Transport CDROM M0502CD
Military Equipment and Material CDROM M0452CD
Military Equipment and Material M0452
Farm Products and Miscellaneous Building Materials CDROM M0402CD
Farm Products and Miscellaneous Building Materials M0402
Heavy Components and Miscellaneous Commodities CDROM M0352CD
Heavy Components and Miscellaneous Commodities M0352
Wayside Electronics and Mobile Worker Communications Architecture CD M1570CD
Wayside Electronics and Mobile Worker Communications Architecture M1570
Office Architecture and Railroad Electronics Messaging CD M1575CD
Office Architecture and Railroad Electronics Messaging M1575
Locomotive Electronics and Train Consist System Architecture CD M1550CD
Locomotive Electronics and Train Consist System Architecture M1550
Couplers & Freight Car Draft Components CDROM M0601CD
Couplers & Freight Car Draft Components M0601
Multi Level Manual CDROM DP204CD
General Rules CDROM M0202CD
Wheels and Axles CDROM M1151CD
Bearings and Lubrication CDROM M1250CD
Electronically Controlled Brake Systems CDROM M1050CD
Electronically Controlled Brake Systems M1050
Trucks and Truck Details CDROM M0900CD
Couplers and Yoke Details CDROM M1870CD
Trucks and Truck Details M0900
Multi Level Manual DP204
Brakes and Brake Equipment CDROM M1000CD
Brakes and Brake Equipment M1000
Construction and Farm Equipment CDROM M0302CD
Construction and Farm Machinery M0302
Specifications for Tank Cars CDROM M0850CD
Specifications for Tank Cars Paper M0850
Car Construction Fundamentals and Details CDROM M0700CD
Car Construction Fundamentals and Details M0700
Metal Products Including Pipe CDROM M0252CD
Metal Products Including Pipe M0252
Locomotives and Locomotive Equipment CDROM M1700CD
Locomotives and Locomotive Equipment M1700
Quality Assurance M 1003 CDROM M1401CD
Quality Assurance M 1003 M1401
Wheels and Axles M1151
Bearings and Lubrication M1250
Lubrication Manual M1350
Lettering and Marking of Cars CDROM M1450CD
Lettering and Marking of Cars M1450
Design Fab Const. Of Freight Cars CDROM M0750CD
Design Fab Const. Of Freight Cars M0750
Ring Preprinted Poly Binder Binder
Electronics Environmental Requirements and Systems Management CD M1580CD
Electronics Environmental Requirements and Systems Management M1580
Wheels and Axle Shop Manual CDROM M1201CD
Roller Bearing Shop Manual CDROM M1300CD
Wheels and Axle Shop Manual M1201
Roller Bearing Shop Manual M1300

러시아 법규 개정 소식

23 Dec 2013 Comments
Off

러시아 법규 개정 소식

  • Federal Law No. 171-FZ of July 2, 2013 on the amendments to the Federal Law on the official statistical records and the system of state statistics in the Russian Federation and to individual legislative acts of the Russian Federation – method for drawing up statistical records, use of electronic signature and other
  • Federal Law No. 163-FZ of July 2, 2013 on the amendments to Articles 12 and 17 of the Federal Law on the safety of objects of the fuel and power-supply complex – the powers of the Government of the Russian Federation
  • Federal Law No. 159-FZ of July 2, 2013 on the amendments to Articles 25 and 26 of the Federal Law on the use of nuclear energy – licensing of activities in the above area
  • Federal Law No. 150-FZ of July 2, 2013 on the amendments to individual legislative acts of the Russian Federation (not yet entered in force) – criminal responsibility for illegal supply and circulation of especially valuable wild animals and aquatic bioresources
  • Order of the Federal Tax Service No. MMV-7-6/155@ of April 24, 2013 on the amendments to Order of the Federal Tax Service No. MMV-7-6/80@ of February 13, 2012 – information submitted by foreign organisations
  • Order of the Ministry of Industry and Trade of the Russian Federation No. 99 of January 29, 2013 on the endorsement of the Administrative Regulation of the Ministry of Industry and Trade on the provided state service of licensing of activities of development, production, testing, storage, repair and utilisation of civil and service arms and main parts of firearms, sale of civil and service arms and main parts of firearms pertaining to works (services) of development, production, testing, repair, utilisation of civil and service arms and main parts of firearms

벽지CE 인증[CE-marking of Wall Covering]

23 Dec 2013 Comments
Off

EN 15102: Decorative wallcoverings

                     – Roll and panel form products

Orange115

Materials produced for incorporation in a permanent manner in construction works, including both buildings and civil engineering works, must comply with the fundamental regulations during an economically relevant lifetime, provided regular maintenance is carried out.

These fundamental regulations include:

˜˜ – mechanical strength and stability
˜˜ – safety in the case of fire
˜˜ – hygiene, health and environment
˜˜ – safety and accessibility in use
˜˜ – protection against noise
˜˜ – energy economy and heat retention
˜˜ – sustainability of natural resources

The regulation only indicates the essential requirements. How these essential requirements have to be met is left to experts who translate them into specific parameters such as – in the case of fire safety -ignitability, flame propagation, smoke propagation.
These parameters will then have to be measured, implying both test methods and classifications. A material complying with the mandatory classifications will thus automatically comply with the essential requirements of the regulation.
The European standardisation committee CEN /TC 99 has developed the harmonised standard EN 15102 for wall coverings. EN15102 was published in September 2007 and harmonised by publication by the EU on December 18th, 2009.
CE marking according to the new regulation on wall coverings is mandatory since July 1st, 2013.

The harmonised standard describes:

-˜˜ reaction to fire* according to EN 13501-1
˜˜- release of formaldehyde * according to EN 12149
˜˜- release of heavy metals* according to EN 12149
˜˜- release of vinyl chloride monomer (VCM )* according to EN 12149
˜˜- sound absorption according to ISO 354
˜˜- thermal resistance according to EN 12667 or EN 12524
*essential requirements

The conformity of a wall covering with the requirements of EN 15102 must be attested in part by the producer himself, but for certain characteristics, the producer will have to apply to an notified testing laboratory or to a notified product certification and inspection body.
The conformity of products shall be analysed and controlled according to different systems. The systems may vary according to the complexity of the regulations and tests necessary to demonstrate the conformity of the product with the manufacturer’s claims.

 Orange115

 Attestation level of conformity type system  1

This system is mandatory for fire classes A1, A2, B and C for those products that have obtained these fire classes by adding fire retardant additives during the production process.
Tasks under the responsibility of the manufacturer or distributor :

˜˜ – maintain factory production control (FPC )
-˜˜ draw up declaration of performance (DoP)
˜˜- submit an application for initial type testing to a notified test lab of all essential requirements:

• reaction to fire
• release of formaldehyde (if relevant)
• release of heavy metals (if relevant)
• release of vinyl chloride monomer (VCM ) (if relevant)

˜˜- submit an application for initial control of the factory and factory production control (FPC ) by a notified product certification and inspection body

˜˜ – affix CE -marking upon packaging and on commercial documentation

 

CE marking of conformity type system  1

on packaging and commercial documentation

 

ce-mark

EN 15102:2007+A1:2011
12 (last two digits of the year in which the marking is affixed)
0493/CPR /XXXX (number of declaration of performance)
Wallcovering
Name and address of the manufacturer/distributor or identifying mark if not mentioned elsewhere on the packaging
Reaction to fire class:
Release of formaldehyde:
release of heavy metals:
release of vinyl chloride monomer:
sound absorption:
thermal resistance: