Archive for year: 2016

IP Code

IP Code에 대한 이해

IP 5K4K란?

 

IP Code는 보통 international protection Code로 알리어지거나 또는 Ingress protection으로 불려지고 있다. 모두 먼지와 물의 침투에 관한 등급 표기 방식이다.

각 규격 별로 약간의 다른 등급표기가 있으나 의미상 내용은 크게 다르지 않으나 유사한 세부적 분류의 표기법이 있다.

다음은 규격의 전부 또는 일부로써 IP code를 다루고 있는 규격 사례들이며 각 규격의 적용분야는 서로 다르지만 의도하는 목적은 같다.

  1. DIN EN 60068-2-18 ; Environmental testing: water
  2. DIN EN 60529; VDE 0470-1  ;Degrees of Protection provided by Enclosures (IP-Code)
  3. ISO 20653 Road vehicles — Degrees of protection (IP-Code) (replacing DIN 40050)
  4. MIL-STD-810G Rain Dust
  5. NEMA 250 : 전기공업협회
  6. RTCA/DO-160G ; Waterproofness
  7. VW 80000 ; Automotive

 

 

IP Code 표기법

IP X 0

의미

ISO 20653

DIN EN 60529

먼지에 대한 보호

0

0

no protection

1

1

먼지 ≥ 50mm

2

2

먼지 ≥ 12,5mm

3

3

먼지 ≥ 2,5mm

4

4

먼지 ≥ 1mm

5K

5

Dust(먼지) protected

6K

6

Dust(먼지) tight

 

 

 

IP 0 X
물의 침투에 대한 보호

ISO 20653

DIN EN 60529

0

0

1

1

2

2

3

3

4

4

4K

-

5

5

6

6

6K

 -

7

7

8

8

 -

9

9K

 -

APN_시험인증_IP_Code_IP4K5K

ASTM E119 Fire Testing

25 Mar 2016 Comments
Off

ASTM E 119

-  건물 건축 및 건축 재료의 화재 시험을 위한 표준 시험 방법

ASTM E84,  NFPA 285, UL 790, BS 476-6/7, NF P92-507, DIN 4102, EN 13501, GB 8624, BS 476-20,EN 1363 등 있으나 ASTM E119은 이들 보다 특별한 시험이다.

 

ASTM E 119 적용대상

  1. Bearing Walls and Partitions
  2. Columns
  3. Floors and Roofs
  4. Loaded Restrained Beams
  5. Nonbearing Walls and Partitions
  6. Protective Membranes in Wall, Partition, Floor, Roof Assemblies
  7. Solid Structural Steel Beams, Girders
  8. Structural Steel Columns

 

ASTM E 119 관련 참고 규격

  1. ASTM C 569 Indentation Hardness of Preformed Thermal Insulations
  2. ASTM E 176 Terminology for Fire Standards

 

ASTM E 119 측정 단계

  1. 1000°F (538°C) at 5 min
  2. 1300°F (704°C) at 10 min
  3. 1550°F (843°C) at 30 min
  4. 1700°F (927°C) at 1 h
  5. 1850°F (1010°C) at 2 h
  6. 2000°F (1093°C) at 4 h
  7. 2300°F (1260°C) at 8 h

 

HOSE STREAM TEST

소방수 분사 시험의 일종으로 정해진 압력으로 소방수를 방수한 후 그 결과를 확인함.

ASTM E 119 비교대상

BS 476-20 : Fire tests on building materials and structures – Method for determination of fire resistance of elements of construction

EN 1363 : Fire Resistance Tests

 

[참고] 규격별 구분.

1.     Cone Calorimeter
           - ASTM E1354
2.     ISMA
           - NFPA 285. ASTM E2307
3.     Large Scale Vertical Furnace
            – ASTM E119. ASTM E1966. NFPA 251. NFPA 252. NFPA 257. UL 9. UL 10B. UL 10C. UL 263.
4.     Roof Testing
           - ASTM E108. UL 790
5.     Small Scale
           - ASTM D635. ASTM D1929. ASTM D2843. ASTM E136. NFPA 701.
6.     Steiner Tunnel
           - ASTM E84. UL 723. CAN/ULC-S102. NFPA 255

시료의 사례)

ASTM E119_Wall_Construction_3Hrs_hose stream

ASTM E119 Fire Testing

MBN LV 124-1

16 Mar 2016 Comments
Off

MBN LV 124-1

Mercedes Benz Company Standard MBN LV 124-1 : Electric and Electronic Components in Motor Vehicles up to 3,5t-General Requirements, Test Conditions and tests, Part 1 : Electrical Requirements and test 12 V On – Board Electrical System.

 

MBN LV 124-1 규격은 Benz, BMW, Audi, Daimler, Porsche, Volkswagen 등 완성차 제조사 들이 Working Group 4.9 (Process Assurance of Supplier Hardware Quality of Electronic Components)에 참여하여 작성한 이들 회사의 회사 공통 규격이다.

 

이 규격은 Part 1 : Part 1 : Electrical Requirements and test 12 V On – Board Electrical System.  및 Part 2 : Environmental Requirements  등 두 가지의 규격으로 나눠진다.

 

이 규격 MEN LV124는 Part 1에서 Electrical requirements and tests 의 E-01~E22, Part 2에서 Environmental requirements의 8. Mechanical 은 M-01~M-06, 9. Climatic Requirements and test 는 K-01~K-18, 11. Life tests는 L-01~L3으로 분류된다.

MBN LV 124 Download

 

 

Acoustics and Vibration

25 Feb 2016 Comments
Off

소음진동  시험관련

Acoustic Testing은 가정용, 산업용 그리고 우주 항공분야 등 다양한 분야에 적용되고 있습니다.

  • Aeroelastic Analysis
  • Modal Testing
  • Vibro-acoustic Analysis
  • Statistical Energy Analysis (SEA)을 이용한 Acoustic Flight Testing
  • Computational Fluid Dynamics(CFD) Analysis
  • Press Map Analysis

위 각 방법에 관한 Test planning을 지원하고 있습니다.

 

Acoustic and Airborne

  1. BS EN ISO 10140-1 – Laboratory Measurements of Sound Insulation of Building Elements
  2. BS EN ISO 10140-2 – Measurement of Airborne Sound Insulation
  3. BS EN ISO 10140-4 – Measurement Procedures and Requirements
  4. BS EN ISO 10140-5 – Requirements for Test Facilities and Equipment
  5. ANSI/AMCA 210/ASHRAE 51 Figure 12, Figure 15 :Aerodynamic Performance
  6. AMCA 300 : Acoustic Performance
  7. HVI 915 : Loudness Rating
  8. HVI 916 : Air Flow
  9. ANSI/AHRI 430 : Central Station Air Handling Units Aerodynamic Performance
  10. ASTM E90 :Acoustic Louvers Acoustic Performance
  11. ANSI S12.51-2002; ISO 3741: Comparison Method Reference Sound Sources Acoustic Performance
  12. GR-63; GR-487;ETSI EN 300 753;ISO 7779; ISO 3744; ISO 9295 Acoustic Pressure (Sound Pressure Level / Sound Power Level)
  13. EN 12102 : Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling Measurement of airborne noise – Determination of the sound power level
  14. EN 12354-1 : Building Acoustic – Part 1: Airborne sound insulation between rooms
  15. EN 12354-2 : Building Acoustic – Part 2: Impact sound insulation between rooms
  16. EN 12354-3 : Building Acoustic – Part 3: Airborne sound insulation against outdoor sound
  17. EN 12354-4 : Building Acoustic – Part 4: Transmission of indoor sound to the outside
  18. EN 12545 : Footwear, leather and imitation leather goods manufacturing machines Noise test code – Common requirements
  19. EN 12549 : Acoustic Noise test code for fastener driving tools
  20. EN 1265 : Safety of machinery Noise test code – for foundry machines and equipment
  21. EN 12758 : Glass in building Glazing and airborne sound insulation – Product descriptions and determination of properties
  22. EN 13023 : Noise measurement methods – for printing, paper converting, paper making machines and auxiliary equipment – Accuracy grades 2 and 3
  23. EN 1330-9 : Non-destructive testing Terms used in Acoustic emission testing
  24. EN 13477-1 : Non-destructive testing Acoustic emission – Part 1: Equipment description
  25. EN 13477-2 : Non-destructive testing Acoustic emission – Part 2: Verification of operating characteristic
  26. EN 13554 : Non-destructive testing Acoustic emission testing – General principles
  27. EN 13819-2 : Hearing protectors , Testing , Acoustic test methods
  28. EN 13950 : Gypsum board thermal/Acoustic insulation composite panels
  29. EN 14389-1 : Road traffic noise reducing devices – Part 1: Acoustical characteristics
  30. EN 14389-2 : Road traffic noise reducing devices – Part 2: Non-Acoustical characteristics
  31. EN 14462 : Surface treatment equipment Noise test code- for surface treatment equipment including its ancillary handling equipment – Accuracy grades 2 and 3
  32. EN 14496 : Gypsum based adhesives for thermal/Acoustic insulation composite panels and plasterboards
  33. EN 14584 : Non-destructive testing Acoustic emission testing – Examination of metallic pressure equipment during proof testing – Planar location of AE sources
  34. EN 14759 : Shutters Acoustic insulation – relative to airborne sound – Expression of performance
  35. EN 1501-4 : Refuse collection vehicles and their associated lifting devices Noise test code for refuse collection vehicles
  36. EN 15036-1 : Heating boilers airborne noise emissions from heat generators – Part 1: Airborne noise emissions from heat generators
  37. EN 15036-2 : Heating boilers airborne noise emissions from heat generators – Part 2: Flue gas noise emissions at the outlet of the heat generator
  38. EN 15042-1 : Thickness measurement , laser induced surface Acoustic waves
  39. EN 15251 : Indoor environmental input parameters energy performance of buildings addressing indoor air quality, thermal environment, lighting and Acoustics
  40. EN 15461 : Railway applications – Characterisation of the dynamic properties of track sections for pass by noise measurements
  41. EN 1547 : Industrial thermoprocessing equipment Noise test code for industrial thermoprocessing equipment including its ancillary handling equipment
  42. EN 15495 : Non Destructive testing – Acoustic emission Examination of metallic pressure equipment during proof testing – Zone location of AE sources
  43. EN 15610 : Railway applications – Rail roughness measurement related to rolling noise generation
  44. EN 15657-1 : Acoustic properties of building elements and of buildings Simplified cases- where the equipment mobilities are much higher than the receiver mobilities, taking whirlpool baths as an example
  45. EN 15892 : Railway applications – Measurement of noise inside driver’s cabs
  46. EN 15910 : Water quality – Guidance on the estimation of fish abundance with mobile hydroAcoustic methods
  47. EN 16025-1 : Thermal and/or sound insulating products in building construction – Bound EPS ballastings – Part 1: Requirements for factory premixed EPS dry plaster
  48. EN 16205 : measurement of walking noise on floors
  49. EN 16272-1 : Railway applications – Noise barriers and related devices acting on airborne sound propagation – Test method for determining the Acoustic performance – Part 1: Intrinsic characteristics – Sound absorption in the laboratory under diffuse sound field conditions
  50. EN 16272-2 : Railway applications – Noise barriers and related devices acting on airborne sound propagation – Test method for determining the Acoustic performance – Part 2: Intrinsic characteristics – Airborne sound insulation in the laboratory under diffuse sound field conditions
  51. EN 16272-3-1 : Railway applications – Noise barriers and related devices acting on airborne sound propagation – Test method for determining the Acoustic performance – Part 3
  52. EN 16272-3-2 : Railway applications – Noise barriers and related devices acting on airborne sound propagation – Test method for determining the Acoustic performance – Part 3
  53. EN 16272-6 : Railway applications – Noise barriers and related devices acting on airborne sound propagation – Test method for determining the Acoustic performance – Part 6: Intrinsic characteristics – In situ values of airborne sound insulation under direct sound field conditions
  54. EN 16286-2 : Railway applications Acoustic measurements
  55. EN 16487 : Acoustic Test code for suspended ceilings – Sound absorption
  56. EN 16583 : Heat exchangers the sound power level
  57. EN 16644 : Rotodynamic pumps Noise test code- (vibro-Acoustics) for measuring structure- and fluid-borne noise
  58. EN 16703 : Acoustics Airborne sound insulation
  59. EN 1746 : Safety of machinery noise clauses of safety
  60. EN 1793-1 : Road traffic noise reducing devices – Part 1: Intrinsic characteristics of sound absorption
  61. EN 1793-2 : Road traffic noise reducing devices – Part 2: Intrinsic characteristics of airborne sound insulation under diffuse sound field conditions
  62. EN 1793-3 : Road traffic noise reducing devices – Part 3: Normalized traffic noise spectrum
  63. EN 1793-4 : Road traffic noise reducing devices – Part 4: Intrinsic characteristics
  64. EN 1793-5 : Road traffic noise reducing devices – Part 5: Intrinsic characteristics
  65. EN 1793-6 : Road traffic noise reducing devices – Part 6: Intrinsic characteristics
  66. EN 1794-1 : Road traffic noise reducing devices , Non-Acoustic performance , Mechanical
  67. EN 1794-2 : Road traffic noise reducing devices , Non-Acoustic performance ,General safety and environmental requirements
  68. EN 1915-4 : Aircraft ground support equipment -Noise measurement methods and reduction
  69. EN 24869-1 : Acoustics Hearing protectors – Subjective method for the measurement of sound attenuation
  70. EN 27574-1 : Acoustics Statistical methods General considerations and definitions
  71. EN 27574-2 : Acoustics Methods for stated values for individual machines
  72. EN 27574-3 : Acoustics Simple (transition) method for stated values for batches of machines
  73. EN 27574-4 : Acoustics Methods for stated values for batches of machines
  74. EN 28960 : Refrigerators, frozen-food storage cabinets and food freezers for household and similar use – Measurement of emission of airborne Acoustical noise
  75. EN 29052-1 : Acoustics Materials used under floating floors in dwellings
  76. EN 29053 : Acoustics Determination of airflow resistance
  77. EN 352-5 : Hearing protectors Active noise reduction- ear-muffs
  78. EN 415-9 : Safety of packaging machines Noise measurement methods -for packaging machines, packaging lines and associated equipment, grade of accuracy 2 and 3
  79. EN ISO 10052 : Acoustic Field measurements of airborne and impact sound insulation and of service equipment sound – Survey method
  80. EN ISO 10140-1 : Acoustic Laboratory measurement of sound insulation of building elements – Part 1: Application rules for specific products
  81. EN ISO 10140-2 : Acoustic Laboratory measurement of sound insulation of building elements – Part 2: Measurement of airborne sound insulation
  82. EN ISO 10140-3 : Acoustic Laboratory measurement of sound insulation of building elements – Part 3: Measurement of impact sound insulation
  83. EN ISO 10140-4 : Acoustic Laboratory measurement of sound insulation of building elements – Part 4: Measurement procedures and requirements
  84. EN ISO 10140-5 : Acoustic Laboratory measurement of sound insulation of building elements – Part 5: Requirements for test facilities and equipment
  85. EN ISO 10534-1 : Acoustic Determination of sound absorption coefficient and impedance in impedances tubes – Part 1: Method using standing wave ratio
  86. EN ISO 10534-2 : Acoustic Determination of sound absorption coefficient and impedance in impedances tubes – Part 2: Transfer-function method
  87. EN ISO 10846-1 : Acoustics and vibration – Part 1: Principles and guidelines
  88. EN ISO 10846-2 : Acoustics and vibration – Part 2: Direct method for determination of the dynamic stiffness of resilient supports for translatory motion
  89. EN ISO 10846-3 : Acoustics and vibration – Part 3: Indirect method for determination of the dynamic stiffness of resilient supports for translatory motion
  90. EN ISO 10846-4 : Acoustics and vibration – Part 4: Dynamic stiffness of elements other than resilient supports for translatory motion
  91. EN ISO 10846-5 : Acoustics and vibration – Part 5: Driving point method for determination of the low-frequency transfer stiffness of resilient supports for translatory motion
  92. EN ISO 10848-1 : Acoustic Laboratory measurement of the flanking transmission of airborne and impact sound between adjoining rooms – Part 1: Frame document
  93. EN ISO 10848-2 : Acoustic Laboratory measurement of the flanking transmission of airborne and impact sound between adjoining rooms – Part 2: Application to light elements when the junction has a small influence
  94. EN ISO 10848-3 : Acoustic Laboratory measurement of the flanking transmission of airborne and impact sound between adjoining rooms – Part 3: Application to light elements when the junction has a substantial influence
  95. EN ISO 10848-4 : Acoustic Laboratory measurement of the flanking transmission of airborne and impact sound between adjoining rooms – Part 4: Application to junctions with at least one heavy element -
  96. EN ISO 11200 : Acoustic Noise emitted by machinery and equipment – Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions
  97. EN ISO 11201 : Acoustic Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
  98. EN ISO 11202 : Acoustic Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
  99. EN ISO 11203 : Acoustic Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
  100. EN ISO 11204 : Acoustic Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
  101. EN ISO 11205 : Acoustic Noise emitted by machinery and equipment – Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity
  102. EN ISO 11546-1 : Acoustic Determination of sound insulation performances of enclosures – Part 1: Measurements under laboratory conditions
  103. EN ISO 11546-2 : Acoustic Determination of sound insulation performances of enclosures – Part 2: Measurements
  104. EN ISO 11553-3 : Safety of machinery Noise reduction and noise measurement methods- for laser processing machines and hand-held processing devices and associated auxiliary equipment
  105. EN ISO 11654 : Acoustic Sound absorbers for use in buildings – Rating of sound absorption
  106. EN ISO 11688-1 : Acoustic Recommended practice for the design of low-noise machinery and equipment – Part 1: Planning
  107. EN ISO 11688-2 : Acoustic Recommended practice for the design of low-noise machinery and equipment – Part 2: Introduction to the physics of low-noise design
  108. EN ISO 11689 : Acoustic Procedure for the comparison of noise-emission data for machinery and equipment
  109. EN ISO 11690-1 : Acoustic Recommended practice for the design of low-noise workplaces containing machinery – Part 1: Noise control strategies
  110. EN ISO 11690-2 : Acoustic Recommended practice for the design of low-noise workplaces containing machinery – Part 2: Noise control measures
  111. EN ISO 11690-3 : Acoustic Recommended practice for the design of low-noise workplaces containing machinery – Part 3: Sound propagation and noise prediction in workrooms
  112. EN ISO 11691 : Acoustic Measurement of insertion loss of ducted silencers without flow – Laboratory survey method
  113. EN ISO 11819-1 : Acoustic Measurement of the influence of road surfaces on traffic noise – Part 1: Statistical Pass-By method
  114. EN ISO 11820 : Acoustic Measurements on silencers
  115. EN ISO 11821 : Acoustic Measurement of the in situ sound attenuation of a removable screen
  116. EN ISO 11904-1 : Acoustic Determination of sound immission from sound sources placed close to the ear – Part 1: Technique using a microphone in a real ear (MIRE technique)
  117. EN ISO 11904-2 : Acoustic Determination of sound immission from sound sources placed close to the ear – Part 2: Technique using a manikin
  118. EN ISO 11957 : Acoustic Determination of sound insulation performance of cabins – Laboratory and in situ measurements
  119. EN ISO 12001 : Acoustic Noise emitted by machinery and equipment – Rules for the drafting and presentation of a noise test code
  120. EN ISO 12999-1 : Acoustic Determination and application of measurement uncertainties in building Acoustic Part 1: Sound insulation
  121. EN ISO 140-18 : Acoustic Measurement of sound insulation in buildings and of building elements – Part 18: Laboratory measurement of sound generated by rainfall on building elements
  122. EN ISO 14163 : Acoustic Guidelines for noise control by silencers
  123. EN ISO 14257 : Acoustic Measurement and parametric description of spatial sound distribution curves in workrooms for evaluation of their Acoustical performance
  124. EN ISO 14509-1 : Small craft Airborne sound emitted by powered recreational craft – Part 1: Pass-by measurement procedures
  125. EN ISO 14509-2 : Small craft Airborne sound emitted by powered recreational craft – Part 2: Sound assessment using reference craft
  126. EN ISO 14509-3 : Small craft Airborne sound emitted by powered recreational craft – Part 3: Sound assessment using calculation and measurement procedures
  127. EN ISO 15186-1 : Acoustic Measurement of sound insulation in buildings and of building elements using sound intensity – Part 1: Laboratory measurements
  128. EN ISO 15186-2 : Acoustic Measurement of sound insulation in buildings and of building elements using sound intensity – Part 2: Field measurements
  129. EN ISO 15186-3 : Acoustic Measurement of sound insulation in buildings and of building elements using sound intensity – Part 3: Laboratory measurements at low frequencies
  130. EN ISO 15667 : Acoustic Guidelines for noise control by enclosures and cabins
  131. EN ISO 15744 : Hand-held non-electric power tools Noise measurement code
  132. EN ISO 16032 : Acoustic Measurement of sound pressure level from service equipment in buildings
  133. EN ISO 16251-1 : Acoustic Laboratory measurement of the reduction of transmitted impact noise by floor coverings on a small floor mock-up – Part 1: Heavyweight compact floor
  134. EN ISO 16283-1 : Acoustic Field measurement of sound insulation in buildings and of building elements – Part 1: Airborne sound insulation
  135. EN ISO 16283-2 : Acoustic Field measurement of sound insulation in buildings and of building elements – Part 2: Impact sound insulation
  136. EN ISO 16283-3 : Acoustic Field measurement of sound insulation in buildings and of building elements – Part 3: Façade sound insulation
  137. EN ISO 1680 : Acoustic Test code for the measurement of airborne noise emitted by rotating electrical machines
  138. EN ISO 1683 : Acoustic Preferred reference values for Acoustical and vibratory levels
  139. EN ISO 17201-1 : Acoustic Noise from shooting ranges – Part 1: Determination of muzzle blast by measurement
  140. EN ISO 17201-2 : Acoustic Noise from shooting ranges – Part 2: Estimation of muzzle blast and projectile sound by calculation
  141. EN ISO 17201-3 : Acoustic Noise from shooting ranges – Part 3: Guidelines for sound propagation calculations
  142. EN ISO 17201-4 : Acoustic Noise from shooting ranges – Part 4: Prediction of projectile sound
  143. EN ISO 17201-5 : Acoustics Noise management
  144. EN ISO 17624 : Acoustic Guidelines for noise control in offices and workrooms by means of Acoustical screens
  145. EN ISO 18233 : Acoustic Application of new measurement methods in building and room Acoustics
  146. EN ISO 20361 : Liquid pumps and pump units Noise test code – Grades 2 and 3 of accuracy
  147. EN ISO 2151 : Acoustic Noise test code for compressors and vacuum pumps
  148. EN ISO 22868 : Forestry and gardening machinery Noise test code-for portable hand-held machines with internal combustion engine -(ISO 22868:2011)
  149. EN ISO 23771 : Textile machinery the noise emissions
  150. EN ISO 266 : Acoustic Preferred frequencies
  151. EN ISO 2922 : Acoustic Measurement of airborne sound emitted by vessels on inland waterways and harbours – Amendment 1
  152. EN ISO 3095 : Acoustic Railway applications – Measurement of noise emitted by railbound vehicles
  153. EN ISO 3381 : Railway applications Acoustic Measurement of noise inside railbound vehicles
  154. EN ISO 3382-1 : Acoustic Measurement of room Acoustic parameters – Part 1: Performance spaces
  155. EN ISO 3382-2 : Acoustic Measurement of room Acoustic parameters – Part 2: Reverberation time in ordinary rooms
  156. EN ISO 3382-3 : Acoustic Measurement of room Acoustic parameters – Part 3: Open plan offices
  157. EN ISO 354 : Acoustics Measurement of sound absorption in a reverberation room
  158. EN ISO 3740 : Acoustic Determination of sound power levels of noise sources – Guidelines for the use of basic standards
  159. EN ISO 3741 : Acoustic Precision methods for reverberation test rooms
  160. EN ISO 3743-1 : Acoustic Engineering methods for small movable sources in reverberant fields – Part 1: Comparison method for a hard-walled test room
  161. EN ISO 3743-2 : Acoustic Determination of sound power levels of noise sources using sound pressure – Engineering methods for small, movable sources in reverberant fields – Part 2: Methods for special reverberation test rooms
  162. EN ISO 3744 : Acoustic Engineering methods for an essentially free field over a reflecting plane
  163. EN ISO 3745 : Acoustic Precision methods for anechoic rooms and hemi-anechoic rooms
  164. EN ISO 3746 : Acoustic Survey method using an enveloping measurement surface over a reflecting plane
  165. EN ISO 3747 : Acoustic Engineering/survey methods for use in situ in a reverberant environment
  166. EN ISO 3822-1 : Acoustic Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 1: Method of measurement
  167. EN ISO 3822-2 : Acoustic Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 2: Mounting and operating conditions for draw-off taps and mixing valves
  168. EN ISO 3822-3 : Acoustic Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 3: Mounting and operating conditions for in-line valves and appliances
  169. EN ISO 3822-4 : Acoustic Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 4: Mounting and operating conditions for special appliances
  170. EN ISO 389-1 : Acoustic Reference zero for the calibration of audiometric equipment – Part 1: Reference equivalent threshold sound pressure levels for pure tones and supra-aural earphones
  171. EN ISO 389-2 : Acoustic Reference zero for the calibration of audiometric equipment – Part 2: Reference equivalent threshold sound pressure levels for pure tones and insert earphones
  172. EN ISO 389-3 : Acoustic Reference zero for the calibration of audiometric equipment – Part 3: Reference equivalent threshold vibratory force levels for pure tones and bone vibrators
  173. EN ISO 389-4 : Acoustic Reference zero for the calibration of audiometric equipment – Part 4: Reference levels for narrow-band masking noise
  174. EN ISO 389-5 : Acoustic Reference zero for the calibration of audiometric equipment – Part 5: Reference equivalent threshold sound pressure levels for pure tones in the frequency range 8 kHz to 16 kHz
  175. EN ISO 389-6 : Acoustic Reference zero for the calibration of audiometric equipment – Part 6: Reference threshold of hearing for test signals of short duration
  176. EN ISO 389-7 : Acoustic Reference zero for the calibration of audiometric equipment – Part 7: Reference threshold of hearing under free-field and diffuse-field listening conditions
  177. EN ISO 389-8 : Acoustic Reference zero for the calibration of audiometric equipment – Part 8: Reference equivalent threshold sound pressure levels for pure tones and circumaural earphones
  178. EN ISO 389-9 : Acoustic Reference zero for the calibration of audiometric equipment – Part 9: Preferred test conditions for the determination of reference hearing threshold levels
  179. EN ISO 4869-2 : Acoustic Hearing protectors – Part 2: Estimation of effective A-weighted sound pressure levels when hearing protectors are worn
  180. EN ISO 4869-3 : Acoustic Hearing protectors – Part 3: Measurement of insertion loss of ear-muff type protectors using an Acoustic test fixture
  181. EN ISO 4869-4 : Acoustic Hearing protectors – Part 4: Measurement of effective sound pressure levels for level-dependent sound-restoration ear-muffs
  182. EN ISO 4871 : Acoustic Declaration and verification of noise emission values of machinery and equipment
  183. EN ISO 5135 : Acoustic Determination of sound power levels of noise from air terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room
  184. EN ISO 5136 : Acoustic Determination of sound power radiated into a duct by fans and other air-moving devices – In-duct method
  185. EN ISO 6926 : Acoustic Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels
  186. EN ISO 7029 : Acoustic Statistical distribution of hearing threshold as a function of age
  187. EN ISO 717-1 : Acoustic Rating of sound insulation in buildings and of building elements – Part 1: Airborne sound insulation
  188. EN ISO 717-2 : Acoustic Rating of sound insulation in buildings and of building elements – Part 2: Impact sound insulation
  189. EN ISO 7235 : Acoustic Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss
  190. EN ISO 7779 : Acoustic Measurement of airborne noise emitted by information technology and telecommunications equipment
  191. EN ISO 8253-1 : Acoustic Audiometric test methods – Part 1: Pure-tone air and bone conduction audiometry
  192. EN ISO 8253-2 : Acoustic Audiometric test methods – Part 2: Sound field audiometry with pure-tone and narrow-band test signals
  193. EN ISO 8253-3 : Acoustic Audiometric test methods – Part 3: Speech audiometry
  194. EN ISO 9295 : Acoustic Determination of high frequency sound power levels emitted by machinery and equipment
  195. EN ISO 9612 : Acoustic Determination of occupational noise exposure
  196. EN ISO 9614-1 : Acoustic Determination of sound power levels of noise sources using sound intensity – Part 1: Measurement at discrete points
  197. EN ISO 9614-2 : Acoustic Determination of sound power levels of noise sources using sound intensity – Part 2: Measurement by scanning
  198. EN ISO 9614-3 : Acoustic Determination of sound power levels of noise sources using sound intensity – Part 3: Precision method for measurement by scanning
  199. EN ISO 9902-1 : Textile machinery Noise test code – Part 1: Common requirements
  200. EN ISO 9902-2 : Textile machinery Noise test code – Part 2: Spinning preparatory and spinning machinery
  201. EN ISO 9902-3 : Textile machinery Noise test code – Part 3: Nonwoven machinery
  202. EN ISO 9902-4 : Textile machinery Noise test code – Part 4: Yarn processing, cordage and rope manufacturing machinery
  203. EN ISO 9902-5 : Textile machinery Noise test code – Part 5: Weaving and knitting preparatory machinery
  204. EN ISO 9902-6 : Textile machinery Noise test code – Part 6: Fabric manufacturing machinery
  205. EN ISO 9902-7 : Textile machinery Noise test code – Part 7: Dyeing and finishing machinery

RTCA/DO-160

18 Feb 2016 Comments
Off

아래는 RTCA/DO-160 : Environmental Conditions and Test Procedures for Airborne Equipment  관련 각 Section 별 항목입니다.  DO-160 시험은 각 Category별 분류되어 시험이 수행됩니다. 세부 각 Category별 시험은 해당 규격을 참조할 필요가 있습니다.

  1. Section 2.0 Definitions of Terms – General
  2. Section 3.0 Conditions of Tests
  3. Section 4.0 Temperature and Altitude
      1. Equipment Category  A1-A4,  B1-B4,  C1-C4,  D1-D3,  E1-E2,  F1-F4
  4. Section 5.0 Temperature Variation
      1. Category A-C, S1-S2
  5. Section 6.0 Humidity
    1. Category A-C
  6. Section 7.0 Operational Shocks and Crash Safety
    1. Category A-B, D-E
  7. Section 8.0 Vibration
    1. Category S, R, U, U2,H, Z
  8. Section 9.0 Explosion Proofness
    1. Category A, E,  H
  9. Section 10.0 Waterproofness
    1. Category Y, W, R, S
  10. Section 11.0 Fluids Susceptibility
    1. Category F
  11. Section 12.0 Sand and Dust
    1. Category D, S
  12. Section 13.0 Fungus Resistance
    1. Category F
  13. Section 14.0 Salt Spray
    1. Category S, T
  14. Section 15.0 Magnetic Effect
    1. Category Y, Z, A, B, C
  15. Section 16.0 Power Input
    1. Category : A(CF),  A(NF) or A(WF)  and  A, B, D or Z
  16. Section 17.0 Voltage Spike
    1. Category A, B
  17. Section 18.0 Audio Frequency Conducted Susceptibility – Power Inputs
    1. Category R(CF), R(NF) or R(WF)  and R, B, or Z
  18. Section 19.0 Induced Signal Susceptibility
    1. Categories R(CF), R(NF), and R(WF) , A(CF), A(NF), and A(WF) and R, B, and Z correspond to Categories A, B, and Z
  19. Section 20.0 Radio Frequency Susceptibility (Radiated and Conducted)
    1. Category AC AN AW,  BC, BN, BW,   CC, CN, CW,  ZC, ZN, ZW
  20. Section 21.0 Emission of Radio Frequency Energy
    1. Category B, D,  F, G, L, M, O, R, T, W,Q
    2. Category B, L, M, H, P, Q
  21. Section 22.0 Lightning Induced Transient Susceptibility
    1. Category 6 Digit
  22. Section 23.0 Lightning Direct Effects
    1. Category 4 Digit
  23. Section 24.0 Icing
    1. Category A, B, C
  24. Section 25.0 Electrostatic Discharge
    1. Category A
  25. Section 26.0 Fire, Flammability
    1. Category A

MIL-STD-282 : Filter Units

28 Jan 2016 Comments
Off

MIL-STD-282 : Filter Units, Protective Clothing, Gas-Mask Components and Related Products: Performance Test Methods.

이 규격은 1952년경 제정된 MIL-F-10462A를 대체하여 1956년 5월 28일 제정되었습니다.

이 후 2012년 1월 17일, 2012년 9월 24일, 2015년, 6월 30일, 2015년 12월 22일 등 개정되었으나 개정된 이후의 규격은 미국정부와 계약된 공급자에게만 배포가 허용됩니다.  따라서 이 외의 목적으로는 1956년 제정된 규격만 열람할 수 있습니다.

미 국방성 규격 관련  상담문의 

 

Automotive test

24 Jan 2016 Comments
Off

자동차부분 시험 및 인증 안내

VOLKSWAGAN

BENZ

GM

toyota

기타 자동차 부품 시험 상담 바로가기