2006/95/EC Low Voltage Directive (LVD)

1. 저전압지침(2006/95/EC)의 구성

서 론 : 해당되는 지침, 전반적인 해설 및 유의사항
지침본문 : 적용하기 위한 조문, 가맹국의 법적 의무나 권한
Annex I : 안전에 관한 설계 일반 지침 및 기본 요구사항
Annex II : 지침대상 외의 기기
Annex III : A. CE-Marking 표시. B. 적합성 선언서
Annex IV : 내부 제조관리. 기술문서 및 선언서 보관, 제조공정의 관리

Eurasian Commission 제공 – 인증지침,인증안내서,승인기관 조회 등

European Commission에서 제공하는 CE Marking 인증관련 모든 자료가 안내되어있습니다.

2. 대상기기

교류 50-1000 V 및 직류 75-1500V의 정격전압으로 사용하도록 설계된 기기를 적용대상으로 합니다. 많은 기기들이 전기를 동력원으로 사용하기에 적용기기 분야가 다양합니다.

3. 대상 외의 기기(지침 Annex Ⅱ)

다른 기술 지침에 따라 관리되는 대상의 기기로써 다음과 같습니다.

A) 폭발환경에서 사용되는 전기기기
B) 방사선 및 의료용 전기기기
C) 가정용 플러그 및 소켓
D) 화물 및 승객용 엘리베이터의 전기 부품
E) 전력계(Electricity meters)
F) 전기 펜스의 제어기

선박, 항공기, 철도에서 사용되는 특정한 전기기기로써, 가맹국이 참가하고 있는 국제 기관에 의 해 제정 되어진 안전 규격에 적합한 기기

4. 기술문서에 포함사항

A) 자기 적합성 선언서
B) 해당 전기기기의 개요
C) 설계도면
D) 전기회로도면
E) 제품 기술과 사용, 운전 설명서
F) 부품목록 및 부품의 CE인증 취득여부
G) 설계계산
H) 시험성적서

5. 인증절차

일반적으로 인증기관에서 발행하는 CoC(Certificate of Conformity)가 아닌 자기 적합성 선언서 인 DoC( Declaration of Conformity)를 취득합니다.

인증취득 기업체는 시험소 또는 자체 시험을 통해서 인증대상제품이 해당규격에 적합함을 입증하는 성적서를 구비하여 관련 문서를 만들고 인증취득 기업체의 대표자가 선언서에 서명하는 것입니다. 특별히 인증취득 기업이 제 3자 인증기관의 인증서 발급을 요구하지 않는한 CoC 인증서를 발급하지 않습니다.

6. 저전압 지침 관련 EN 규격 목록

  • EN 41003 ; Particular safety requirements for equipment to be connected to telecommunication networks and/or a cable distribution system
  • EN 50065-4-2 ; Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz — Part 4-2: Low voltage decoupling filters – Safety requirements
  • EN 50065-4-7 ; Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz — Part 4-7: Portable low voltage decoupling filters – Safety requirements
  • EN 50085-1 ; Cable trunking systems and cable ducting systems for electrical installations — Part 1: General requirements
  • EN 50085-2-1 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-1: Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings
  • EN 50085-2-2 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-2: Particular requirements for cable trunking systems and cable ducting systems intended for mounting underfloor, flushfloor, or onfloor
  • EN 50085-2-3 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets
  • EN 50085-2-4 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-4: Particular requirements for service poles and service posts
  • EN 50086-2-4 ; Conduit systems for cable management — Part 2-4: Particular requirements for conduit systems buried underground
  • EN 50090-2-2 ; Home and Building Electronic Systems (HBES) — Part 2-2: System overview – General technical requirements
  • EN 50106 ; Safety of household and similar electrical appliances – Particular rules for routine tests referring to appliances under the scope of EN 60335-1
  • EN 50117-1 ; Coaxial cables — Part 1: Generic specification
  • EN 50117-2-1 ; Coaxial cables — Part 2-1: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 1 000 MHz
  • EN 50117-2-2 ; Coaxial cables — Part 2-2: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 1 000 MHz
  • EN 50117-2-3 ; Coaxial cables — Part 2-3: Sectional specification for cables used in cabled distribution networks – Distribution and trunk cables for systems operating at 5 MHz – 1 000 MHz
  • EN 50117-2-4 ; Coaxial cables — Part 2-4: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz
  • EN 50117-2-5 ; Coaxial cables — Part 2-5: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 3 000 MHz
  • EN 50117-3-1 ; Coaxial cables — Part 3-1: Sectional specifications for cables used in Telecom applications – Miniaturized cables used in digital communication systems
  • EN 50117-4-1 ; Coaxial cables — Part 4-1: Sectional specification for cables for BCT cabling in accordance with EN 50173 – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz
  • EN 50156-1 ; Electrical equipment for furnaces and ancillary equipment — Part 1: Requirements for application design and installation
  • EN 50178 ; Electronic equipment for use in power installations
  • EN 50214 ; Flat polyvinyl chloride sheathed flexible cables
  • EN 50250 ; Conversion adaptors for industrial use
  • EN 50262 ; Cable glands for electrical installations
  • EN 50267-1 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 1: Apparatus
  • EN 50267-2-1 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 2-1: Procedures – Determination of the amount of halogen acid gas
  • EN 50267-2-2 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 2-2: Procedures – Determination of degree of acidity of gases for materials by measuring pH and conductivity
  • EN 50267-2-3 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 2-3: Procedures – Determination of degree of acidity of gases for cables by determination of the weighted average of pH and conductivity
  • EN 50274 ; Low-voltage switchgear and controlgear assemblies – Protection against electric shock – Protection against unintentional direct contact with hazardous live parts
  • EN 50288-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 1: Generic specification
  • EN 50288-10-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 10-1: Sectional specification for screened cables characterized up to 500 MHz – Horizontal floor and building backbone cables
  • EN 50288-11-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 11-1: Sectional specification for un-screened cables characterised up to 500 MHz – Horizontal and building backbone cables
  • EN 50288-2-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 2-1: Sectional specification for screened cables characterised up to 100 MHz – Horizontal and building backbone cables
  • EN 50288-2-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 2-2: Sectional specification for screened cables characterised up to 100 MHz – Work area and patch cord cables
  • EN 50288-3-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 3-1: Sectional specification for unscreened cables characterised up to 100 MHz – Horizontal and building backbone cables
  • EN 50288-3-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz – Work area and patch cord cables
  • EN 50288-4-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 4-1: Sectional specification for screened cables characterised up to 600 MHz – Horizontal and building backbone cables
  • EN 50288-4-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 4-2: Sectional specification for screened cables characterised up to 600 MHz – Work area and patch cord cables
  • EN 50288-5-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 5-1: Sectional specification for screened cables characterized up to 250 MHz – Horizontal and building backbone cables
  • EN 50288-5-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 5-2: Sectional specification for screened cables characterized up to 250 MHz – Work area and patch cord cables
  • EN 50288-6-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 6-1: Sectional specification for unscreened cables characterised up to 250 MHz – Horizontal and building backbone cables
  • EN 50288-6-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz – Work area and patch cord cables
  • EN 50288-7 ; Multi-element metallic cables used in analogue and digital communication and control — Part 7: Sectional specification for instrumentation and control cables
  • EN 50288-8 ; Multi-element metallic cables used in analogue and digital communication and control — Part 8: Specification for type 1 cables characterised up to 2 MHz
  • EN 50288-9-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 9-1: Sectional specification for screened cables characterised up to 1 000 MHz – Horizontal and building backbone cables
  • EN 50289-1-3 ; Communication cables – Specifications for test methods — Part 1-3: Electrical test methods – Dielectric strength
  • EN 50289-1-4 ; Communication cables – Specifications for test methods — Part 1-4: Electrical test methods – Insulation resistance
  • EN 50290-2-1 ; Communication cables — Part 2-1: Common design rules and construction
  • EN 50290-2-20 ; Communication cables — Part 2-20: Common design rules and construction – General
  • EN 50290-2-21 ; Communication cables — Part 2-21: Common design rules and construction – PVC insulation compounds
  • EN 50290-2-22 ; Communication cables — Part 2-22: Common design rules and construction – PVC sheathing compounds
  • EN 50290-2-23 ; Communication cables — Part 2-23: Common design rules and construction – PE insulation
  • EN 50290-2-24 ; Communication cables — Part 2-24: Common design rules and construction – PE sheathing
  • EN 50290-2-25 ; Communication cables — Part 2-25: Common design rules and construction – Polypropylene insulation compounds
  • EN 50290-2-26 ; Communication cables — Part 2-26: Common design rules and construction – Halogen free flame retardant insulation compounds
  • EN 50290-2-27 ; Communication cables — Part 2-27: Common design rules and construction – Halogen free flame retardant thermoplastic sheathing compounds
  • EN 50290-2-28 ; Communication cables — Part 2-28: Common design rules and construction – Filling compounds for filled cables
  • EN 50290-2-29 ; Communication cables — Part 2-29: Common design rules and construction – Cross-linked PE insulation compounds
  • EN 50290-2-30 ; Communication cables — Part 2-30: Common design rules and construction – Poly(tetrafluoroethylene-hexafluoropropylene) (FEP) insulation and sheathing
  • EN 50290-4-1 ; Communication cables — Part 4-1: General considerations for the use of cables – Environmental conditions and safety aspects
  • EN 50363-0 ; Insulating, sheathing and covering materials for low-voltage energy cables — Part 0: General introduction
  • EN 50363-0 ; Insulating, sheathing and covering materials for low-voltage energy cables — Part 0: General introduction
  • EN 50363-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 1: Cross-linked elastomeric insulating compounds
  • EN 50363-10-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 10-1: Miscellaneous sheathing compounds – Cross-linked polyvinyl chloride (XLPVC)
  • EN 50363-10-2 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 10-2: Miscellaneous sheathing compounds – Thermoplastic polyurethane
  • EN 50363-2-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 2-1: Cross-linked elastomeric sheathing compounds
  • EN 50363-2-2 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 2-2: Cross-linked elastomeric covering compounds
  • EN 50363-3 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 3: PVC insulating compounds
  • EN 50363-4-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 4-1: PVC sheathing compounds
  • EN 50363-4-2 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 4-2: PVC covering compounds
  • EN 50363-5 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 5: Halogen-free, cross-linked insulating compounds
  • EN 50363-6 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 6: Halogen-free, cross-linked sheathing compounds
  • EN 50363-7 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 7: Halogen-free, thermoplastic insulating compounds
  • EN 50363-8 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 8: Halogen-free, thermoplastic sheathing compounds
  • EN 50363-9-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 9-1: Miscellaneous insulating compounds – Cross-linked polyvinyl chloride (XLPVC)
  • EN 50364 ; Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications
  • EN 50369 ; Liquid tight sheathing systems for cable management
  • EN 50371 ; Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (10 MHz – 300 GHz) – General public
  • EN 50395 ; Electrical test methods for low voltage energy cables
  • EN 50396 ; Non electrical test methods for low voltage energy cables
  • EN 50406-1 ; End user multi-pair cables used in high bit rate telecommunication networks — Part 1: Aerial cables
  • EN 50406-2 ; End user multi-pair cables used in high bit rate telecommunication networks — Part 2: Duct and buried cables
  • EN 50407-1 ; Multi-pair cables used in high bit rate digital access telecommunication networks — Part 1: Outdoor cables
  • EN 50425 ; Switches for household and similar fixed electrical installations – Collateral standard – Fireman’s switches for exterior and interior signs and luminaires
  • EN 50428 ; Switches for household and similar fixed electrical installations – Collateral standard – Switches and related accessories for use in home and building electronic systems (HBES)
  • EN 50441-1 ; Cables for indoor residential telecommunication installations — Part 1: Unscreened cables – Grade 1
  • EN 50441-1 ; Cables for indoor residential telecommunication installations — Part 1: Unscreened cables – Grade 1
  • EN 50441-2 ; Cables for indoor residential telecommunication installations — Part 2: Screened cables – Grade 1
  • EN 50441-2 ; Cables for indoor residential telecommunication installations — Part 2: Screened cables – Grade 2
  • EN 50441-3 ; Cables for indoor residential telecommunication installations — Part 3: Screened cables – Grade 3
  • EN 50441-4 ; Cables for indoor residential telecommunication installations — Part 4: Cables up to 1 200 MHz – Grade 3
  • EN 50445 ; Product family standard to demonstrate compliance of equipment for resistance welding, arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic fields (0 Hz – 300 GHz)
  • EN 50491-3 ; General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) — Part 3: Electrical safety requirements
  • EN 50491-4-1 ; General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) — Part 4-1: General functional safety requirements for products intended to be integrated in Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS)
  • EN 50497 ; Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables
  • EN 50520 ; Cover plates and cover tapes for the protection and location warning of buried cables or buried conduits in underground installations
  • EN 50525-1 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 1: General requirements
  • EN 50525-2-11 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) — Part 2-11: Cables for general applications – Flexible cables with thermoplastic PVC insulation
  • EN 50525-2-12 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) — Part 2-12: Cables for general applications – Cables with thermoplastic PVC insulation for extensible leads
  • EN 50525-2-21 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) — Part 2-21: Cables for general applications – Flexible cables with crosslinked elastomeric insulation
  • EN 50525-2-22 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-22: Cables for general applications – High flexibility braided cables with crosslinked elastomeric insulation
  • EN 50525-2-31 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-31: Cables for general applications – Single core non-sheathed cables with thermoplastic PVC insulation
  • EN 50525-2-41 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-41: Cables for general applications – Single core cables with crosslinked silicone rubber insulation
  • EN 50525-2-42 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-42: Cables for general applications – Single core non-sheathed cables with crosslinked EVA insulation
  • EN 50525-2-51 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-51: Cables for general applications – Oil resistant control cables with thermoplastic PVC insulation
  • EN 50525-2-71 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-71: Cables for general applications – Flat tinsel cables (cords) with thermoplastic PVC insulation
  • EN 50525-2-72 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-72: Cables for general applications – Flat divisible cables (cords) with thermoplastic PVC insulation
  • EN 50525-2-81 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-81: Cables for general applications – Cables with crosslinked elastomeric covering for arc welding
  • EN 50525-2-82 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-82: Cables for general applications – Cables with crosslinked elastomeric insulation for decorative chains
  • EN 50525-2-83 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-83: Cables for general applications – Multicore cables with crosslinked silicone rubber insulation
  • EN 50525-3-11 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-11: Cables with special fire performance – Flexible cables with halogen-free thermoplastic insulation, and low emission of smoke
  • EN 50525-3-21 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-21: Cables with special fire performance – Flexible cables with halogen-free crosslinked insulation, and low emission of smoke
  • EN 50525-3-31 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-31: Cables with special fire performance – Single core non-sheathed cables with halogen-free thermoplastic insulation, and low emission of smoke
  • EN 50525-3-41 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-41: Cables with special fire performance – Single core non-sheathed cables with halogen-free crosslinked insulation, and low emission of smoke
  • EN 50550 ; Power frequency overvoltage protective device for household and similar applications (POP)
  • EN 50557 ; Requirements for automatic reclosing devices (ARDs) for circuit breakers-RCBOs-RCCBs for household and similar uses
  • EN 60034-1 ; Rotating electrical machines — Part 1: Rating and performance
  • EN 60034-1 ; Rotating electrical machines — Part 1: Rating and performance
  • EN 60034-11 ; Rotating electrical machines — Part 11: Thermal protection
  • EN 60034-12 ; Rotating electrical machines — Part 12: Starting performance of single-speed three-phase cage induction motors
  • EN 60034-14 ; Rotating electrical machines — Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher – Measurement, evaluation and limits of vibration severity
  • EN 60034-5 ; Rotating electrical machines — Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification
  • EN 60034-6 ; Rotating electrical machines — Part 6: Methods of cooling (IC Code)
  • EN 60034-7 ; Rotating electrical machines — Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
  • EN 60034-8 ; Rotating electrical machines — Part 8: Terminal markings and direction of rotation
  • EN 60034-9 ; Rotating electrical machines — Part 9: Noise limits
  • EN 60051-1 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 1: Definitions and general requirements common to all parts
  • EN 60051-2 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 2: Special requirements for ammeters and voltmeters
  • EN 60051-3 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 3: Special requirements for wattmeters and varmeters
  • EN 60051-4 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 4: Special requirements for frequency meters
  • EN 60051-5 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 5: Special requirements for phase meters, power factor meters and synchroscopes
  • EN 60051-6 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
  • EN 60051-7 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 7: Special requirements for multi-function instruments
  • EN 60051-8 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 8: Special requirements for accessories
  • EN 60051-9 ; Direct acting indicating analogue electrical-measuring instruments and their accessories — Part 9: Recommended test methods
  • EN 60061-1 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 1: Lamp caps
  • EN 60061-2 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 2: Lampholders
  • EN 60061-3 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 3: Gauges
  • EN 60061-4 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 4: Guidelines and general information
  • EN 60065 ; Audio, video and similar electronic apparatus – Safety requirements
  • EN 60110-1 ; Power capacitors for induction heating installations — Part 1: General
  • EN 60127-1 ; Miniature fuses — Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links
  • EN 60127-2 ; Miniature fuses — Part 2: Cartridge fuse-links
  • EN 60127-3 ; Miniature fuses — Part 3: Sub-miniature fuse-links
  • EN 60127-4 ; Miniature fuses — Part 4: Universal modular fuse-links (UMF) – Through-hole and surface mount types
  • EN 60127-6 ; Miniature fuses — Part 6: Fuse-holders for miniature fuse-links
  • EN 60143-2 ; Series capacitors for power systems — Part 2: Protective equipment for series capacitor banks
  • EN 60155 ; Glow-starters for fluorescent lamps
  • EN 60204-1 ; Safety of machinery – Electrical equipment of machines — Part 1: General requirements
  • EN 60204-32 ; Safety of machinery – Electrical equipment of machines — Part 32: Requirements for hoisting machines
  • EN 60215 ; Safety requirements for radio transmitting equipment
  • EN 60228 ; Conductors of insulated cables
  • EN 60238 ; Edison screw lampholders
  • EN 60252-1 ; AC motor capacitors — Part 1: General – Performance, testing and rating – Safety requirements – Guidance for installation and operation
  • EN 60252-1 ; AC motor capacitors — Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
  • EN 60252-2 ; AC motor capacitors — Part 2: Motor start capacitors
  • EN 60252-2 ; AC motor capacitors — Part 2: Motor start capacitors
  • EN 60255-27 ; Measuring relays and protection equipment — Part 27: Product safety requirements
  • EN 60255-5 ; Electrical relays — Part 5: Insulation coordination for measuring relays and protection equipment – Requirements and tests
  • EN 60269-1 ; Low-voltage fuses — Part 1: General requirements
  • EN 60269-4 ; Low-voltage fuses — Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices
  • EN 60269-6 ; Low-voltage fuses — Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems
  • EN 60309-1 ; Plugs, socket-outlets and couplers for industrial purposes — Part 1: General requirements
  • EN 60309-2 ; Plugs, socket-outlets and couplers for industrial purposes — Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
  • EN 60309-4 ; Plugs, socket-outlets and couplers for industrial purposes — Part 4: Switched socket-outlets and connectors with or without interlock
  • EN 60320-1 ; Appliance couplers for household and similar general purposes — Part 1: General requirements
  • EN 60320-2-1 ; Appliance couplers for household and similar general purposes — Part 2-1: Sewing machine couplers
  • EN 60320-2-2 ; Appliance couplers for household and similar general purposes — Part 2-2: Interconnection couplers for household and similar equipment
  • EN 60320-2-4 ; Appliance couplers for household and similar general purposes — Part 2-4: Appliance couplers dependent on appliance weight for engagement
  • EN 60332-1-1 ; Tests on electric and optical fibre cables under fire conditions — Part 1-1: Test for vertical flame propagation for a single insulated wire or cable – Apparatus
  • EN 60332-1-2 ; Tests on electric and optical fibre cables under fire conditions — Part 1-2: Test for vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixed flame
  • EN 60332-1-3 ; Tests on electric and optical fibre cables under fire conditions — Part 1-3: Test for vertical flame propagation for a single insulated wire or cable – Procedure for determination of flaming droplets/particles
  • EN 60332-2-1 ; Tests on electric and optical fibre cables under fire conditions — Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus
  • EN 60332-2-2 ; Tests on electric and optical fibre cables under fire conditions — Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame
  • EN 60332-3-10 ; Tests on electric and optical fibre cables under fire conditions — Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables – Apparatus
  • EN 60332-3-21 ; Tests on electric and optical fibre cables under fire conditions — Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A F/R
  • EN 60332-3-22 ; Tests on electric and optical fibre cables under fire conditions — Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A
  • EN 60332-3-23 ; Tests on electric and optical fibre cables under fire conditions — Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B
  • EN 60332-3-24 ; Tests on electric and optical fibre cables under fire conditions — Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category C
  • EN 60332-3-25 ; Tests on electric and optical fibre cables under fire conditions — Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category D
  • EN 60335-1 ; Safety of household and similar electrical appliances — Part 1: General requirements
  • EN 60335-2-10 ; Household and similar electrical appliances – Safety — Part 2-10: Particular requirements for floor treatment machines and wet scrubbing machines
  • EN 60335-2-101 ; Household and similar electrical appliances – Safety — Part 2-101: Particular requirements for vaporizers
  • EN 60335-2-102 ; Household and similar electrical appliances – Safety — Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
  • EN 60335-2-105 ; Household and similar electrical appliances – Safety — Part 2-105: Particular requirements for multifunctional shower cabinets
  • EN 60335-2-106 ; Household and similar electrical appliances – Safety — Part 2-106: Particular requirements for heated carpets and for heating units for room heating installed under removable floor coverings
  • EN 60335-2-108 ; Household and similar electrical appliances – Safety — Part 2-108: Particular requirements for electrolysers
  • EN 60335-2-109 ; Household and similar electrical appliances – Safety — Part 2-109: Particular requirements for UV radiation water treatment appliances
  • EN 60335-2-11 ; Household and similar electrical appliances – Safety — Part 2-11: Particular requirements for tumble dryers
  • EN 60335-2-12 ; Household and similar electrical appliances – Safety — Part 2-12: Particular requirements for warming plates and similar appliances
  • EN 60335-2-13 ; Household and similar electrical appliances – Safety — Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances
  • EN 60335-2-14 ; Household and similar electrical appliances – Safety — Part 2-14: Particular requirements for kitchen machines
  • EN 60335-2-15 ; Household and similar electrical appliances – Safety — Part 2-15: Particular requirements for appliances for heating liquids
  • EN 60335-2-16 ; Household and similar electrical appliances – Safety — Part 2-16: Particular requirements for food waste disposers
  • EN 60335-2-17 ; Household and similar electrical appliances – Safety — Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances
  • EN 60335-2-2 ; Household and similar electrical appliances – Safety — Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances
  • EN 60335-2-21 ; Household and similar electrical appliances – Safety — Part 2-21: Particular requirements for storage water heaters
  • EN 60335-2-23 ; Household and similar electrical appliances – Safety — Part 2-23: Particular requirements for appliances for skin or hair care
  • EN 60335-2-24 ; Household and similar electrical appliances – Safety — Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice-makers
  • EN 60335-2-25 ; Household and similar electrical appliances – Safety — Part 2-25: Particular requirements for microwave ovens, including combination microwave ovens
  • EN 60335-2-26 ; Household and similar electrical appliances – Safety — Part 2-26: Particular requirements for clocks
  • EN 60335-2-27 ; Household and similar electrical appliances – Safety — Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation
  • EN 60335-2-28 ; Household and similar electrical appliances – Safety — Part 2-28: Particular requirements for sewing machines
  • EN 60335-2-29 ; Household and similar electrical appliances – Safety — Part 2-29: Particular requirements for battery chargers
  • EN 60335-2-3 ; Household and similar electrical appliances – Safety — Part 2-3: Particular requirements for electric irons
  • EN 60335-2-30 ; Household and similar electrical appliances – Safety — Part 2-30: Particular requirements for room heaters
  • EN 60335-2-31 ; Household and similar electrical appliances – Safety — Part 2-31: Particular requirements for range hoods and other cooking fume extractors
  • EN 60335-2-32 ; Household and similar electrical appliances – Safety — Part 2-32: Particular requirements for massage appliances
  • EN 60335-2-34 ; Household and similar electrical appliances – Safety — Part 2-34: Particular requirements for motor-compressors
  • EN 60335-2-35 ; Household and similar electrical appliances – Safety — Part 2-35: Particular requirements for instantaneous water heaters
  • EN 60335-2-36 ; Household and similar electrical appliances – Safety — Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements
  • EN 60335-2-37 ; Household and similar electrical appliances – Safety — Part 2-37: Particular requirements for commercial electric deep fat fryers
  • EN 60335-2-38 ; Household and similar electrical appliances – Safety — Part 2-38: Particular requirements for commercial electric griddles and griddle grills
  • EN 60335-2-39 ; Household and similar electrical appliances – Safety — Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans
  • EN 60335-2-4 ; Household and similar electrical appliances – Safety — Part 2-4: Particular requirements for spin extractors
  • EN 60335-2-40 ; Household and similar electrical appliances – Safety — Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
  • EN 60335-2-41 ; Household and similar electrical appliances – Safety — Part 2-41: Particular requirements for pumps
  • EN 60335-2-42 ; Household and similar electrical appliances – Safety — Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens
  • EN 60335-2-43 ; Household and similar electrical appliances – Safety — Part 2-43: Particular requirements for clothes dryers and towel rails
  • EN 60335-2-44 ; Household and similar electrical appliances – Safety — Part 2-44: Particular requirements for ironers
  • EN 60335-2-45 ; Household and similar electrical appliances – Safety — Part 2-45: Particular requirements for portable heating tools and similar appliances
  • EN 60335-2-47 ; Household and similar electrical appliances – Safety — Part 2-47: Particular requirements for commercial electric boiling pans
  • EN 60335-2-48 ; Household and similar electrical appliances – Safety — Part 2-48: Particular requirements for commercial electric grillers and toasters
  • EN 60335-2-49 ; Household and similar electrical appliances – Safety — Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm
  • EN 60335-2-5 ; Household and similar electrical appliances – Safety — Part 2-5: Particular requirements for dishwashers
  • EN 60335-2-50 ; Household and similar electrical appliances – Safety — Part 2-50: Particular requirements for commercial electric bains-marie
  • EN 60335-2-51 ; Household and similar electrical appliances – Safety — Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
  • EN 60335-2-52 ; Household and similar electrical appliances – Safety — Part 2-52: Particular requirements for oral hygiene appliances
  • EN 60335-2-53 ; Household and similar electrical appliances – Safety — Part 2-53: Particular requirements for sauna heating appliances
  • EN 60335-2-53 ; Household and similar electrical appliances – Safety — Part 2-53: Particular requirements for sauna heating appliances and infrared cabins
  • EN 60335-2-54 ; Household and similar electrical appliances – Safety — Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam
  • EN 60335-2-54 ; Household and similar electrical appliances – Safety — Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam
  • EN 60335-2-55 ; Household and similar electrical appliances – Safety — Part 2-55: Particular requirements for electrical appliances for use with aquariums and garden ponds
  • EN 60335-2-56 ; Household and similar electrical appliances – Safety — Part 2-56: Particular requirements for projectors and similar appliances
  • EN 60335-2-59 ; Household and similar electrical appliances – Safety — Part 2-59: Particular requirements for insect killers
  • EN 60335-2-6 ; Household and similar electrical appliances – Safety — Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances
  • EN 60335-2-60 ; Household and similar electrical appliances – Safety — Part 2-60: Particular requirements for whirlpool baths and whirlpool spas
  • EN 60335-2-61 ; Household and similar electrical appliances – Safety — Part 2-61: Particular requirements for thermal-storage room heaters
  • EN 60335-2-62 ; Household and similar electrical appliances – Safety — Part 2-62: Particular requirements for commercial electric rinsing sinks
  • EN 60335-2-65 ; Household and similar electrical appliances – Safety — Part 2-65: Particular requirements for air-cleaning appliances
  • EN 60335-2-66 ; Household and similar electrical appliances – Safety — Part 2-66: Particular requirements for water-bed heaters
  • EN 60335-2-7 ; Household and similar electrical appliances – Safety — Part 2-7: Particular requirements for washing machines
  • EN 60335-2-71 ; Household and similar electrical appliances – Safety — Part 2-71: Particular requirements for electrical heating appliances for breeding and rearing animals
  • EN 60335-2-73 ; Household and similar electrical appliances – Safety — Part 2-73: Particular requirements for fixed immersion heaters
  • EN 60335-2-74 ; Household and similar electrical appliances – Safety — Part 2-74: Particular requirements for portable immersion heaters
  • EN 60335-2-75 ; Household and similar electrical appliances – Safety — Part 2-75: Particular requirements for commercial dispensing appliances and vending machines
  • EN 60335-2-78 ; Household and similar electrical appliances – Safety — Part 2-78: Particular requirements for outdoor barbecues
  • EN 60335-2-8 ; Household and similar electrical appliances – Safety — Part 2-8: Particular requirements for shavers, hair clippers and similar appliances
  • EN 60335-2-80 ; Household and similar electrical appliances – Safety — Part 2-80: Particular requirements for fans
  • EN 60335-2-81 ; Household and similar electrical appliances – Safety — Part 2-81: Particular requirements for foot warmers and heating mats
  • EN 60335-2-82 ; Household and similar electrical appliances – Safety — Part 2-82: Particular requirements for amusement machines and personal service machines
  • EN 60335-2-83 ; Household and similar electrical appliances – Safety — Part 2-83: Particular requirements for heated gullies for roof drainage
  • EN 60335-2-84 ; Household and similar electrical appliances – Safety — Part 2-84: Particular requirements for toilets
  • EN 60335-2-85 ; Household and similar electrical appliances – Safety — Part 2-85: Particular requirements for fabric steamers
  • EN 60335-2-86 ; Household and similar electrical appliances – Safety — Part 2-86: Particular requirements for electric fishing machines
  • EN 60335-2-87 ; Household and similar electrical appliances – Safety — Part 2-87: Particular requirements for electrical animal-stunning equipment
  • EN 60335-2-88 ; Household and similar electrical appliances – Safety — Part 2-88: Particular requirements for humidifiers intended for use with heating, ventilation, or air-conditioning systems
  • EN 60335-2-9 ; Household and similar electrical appliances – Safety — Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliances
  • EN 60335-2-90 ; Household and similar electrical appliances – Safety — Part 2-90: Particular requirements for commercial microwave ovens
  • EN 60335-2-96 ; Household and similar electrical appliances – Safety — Part 2-96: Particular requirements for flexible sheet heating elements for room heating
  • EN 60335-2-97 ; Household and similar electrical appliances – Safety — Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment
  • EN 60335-2-98 ; Household and similar electrical appliances – Safety — Part 2-98: Particular requirements for humidifiers
  • EN 60358-1 ; Coupling capacitors and capacitor dividers — Part 1: General rules
  • EN 60360 ; Standard method of measurement of lamp cap temperature rise
  • EN 60399 ; Barrel thread for lampholders with shade holder ring
  • EN 60400 ; Lampholders for tubular fluorescent lamps and starterholders
  • EN 60423 ; Conduit systems for cable management – Outside diameters of conduits for electrical installations and threads for conduits and fittings
  • EN 60432-1 ; Incandescent lamps – Safety specifications — Part 1: Tungsten filament lamps for domestic and similar general lighting purposes
  • EN 60432-2 ; Incandescent lamps – Safety specifications — Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes
  • EN 60432-3 ; Incandescent lamps – Safety specifications — Part 3: Tungsten-halogen lamps (non-vehicle)
  • EN 60432-3 ; Incandescent lamps – Safety specifications — Part 3: Tungsten-halogen lamps (non-vehicle)
  • EN 60439-1 ; Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially type-tested assemblies
  • EN 60439-2 ; Low-voltage switchgear and controlgear assemblies — Part 2: Particular requirements for busbar trunking systems (busways)
  • EN 60439-3 ; Low-voltage switchgear and controlgear assemblies — Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use – Distribution boards
  • EN 60439-4 ; Low-voltage switchgear and controlgear assemblies — Part 4: Particular requirements for assemblies for construction sites (ACS)
  • EN 60439-5 ; Low-voltage switchgear and controlgear assemblies — Part 5: Particular requirements for assemblies for power distribution in public networks
  • EN 60446 ; Basic and safety principles for man-machine interface, marking and identification – Identification of conductors by colours or alphanumerics
  • EN 60477 ; Laboratory d.c. resistors
  • EN 60477-2 ; Laboratory resistors — Part 2: Laboratory a.c. resistors
  • EN 60519-1 ; Safety in electroheating installations — Part 1: General requirements
  • EN 60519-10 ; Safety in electroheat installations — Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications
  • EN 60519-2 ; Safety in electroheat installations — Part 2: Particular requirements for resistance heating equipment
  • EN 60519-21 ; Safety in electroheat installations — Part 21: Particular requirements for resistance heating equipment – Heating and melting glass equipment
  • EN 60519-3 ; Safety in electroheat installations — Part 3: Particular requirements for induction and conduction heating and induction melting installations
  • EN 60519-4 ; Safety in electroheat installations — Part 4: Particular requirements for arc furnace installations
  • EN 60519-6 ; Safety in electroheat installations — Part 6: Specifications for safety in industrial microwave heating equipment
  • EN 60519-6 ; Safety in electroheat installations — Part 6: Specifications for safety in industrial microwave heating equipment
  • EN 60519-7 ; Safety in electroheat installations — Part 7: Particular requirements for installations with electron guns
  • EN 60519-8 ; Safety in electroheat installations — Part 8: Particular requirements for electroslag remelting furnaces
  • EN 60519-9 ; Safety in electroheat installations — Part 9: Particular requirements for high-frequency dielectric heating installations
  • EN 60523 ; Direct-current potentiometers
  • EN 60524 ; Direct-current resistive volt ratio boxes
  • EN 60529 ; Degrees of protection provided by enclosures (IP Code)
  • EN 60564 ; D.C. bridges for measuring resistance
  • EN 60570 ; Electrical supply track systems for luminaires
  • EN 60598-1 ; Luminaires — Part 1: General requirements and tests
  • EN 60598-2-1 ; Luminaires — Part 2: Particular requirements — Section 1: Fixed general purpose luminaires
  • EN 60598-2-10 ; Luminaires — Part 2-10: Particular requirements – Portable luminaires for children
  • EN 60598-2-11 ; Luminaires — Part 2-11: Particular requirements – Aquarium luminaires
  • EN 60598-2-12 ; Luminaires — Part 2-12: Particular requirements – Mains socket-outlet mounted nightlights
  • EN 60598-2-13 ; Luminaires — Part 2-13: Particular requirements – Ground recessed luminaires
  • EN 60598-2-14 ; Luminaires — Part 2-14: Particular requirements – Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment
  • EN 60598-2-17 ; Luminaires — Part 2: Particular requirements — Section 17: Luminaires for stage lighting, television film and photographic studios (outdoor and indoor)
  • EN 60598-2-19 ; Luminaires — Part 2: Particular requirements — Section 19: Air-handling luminaires (safety requirements)
  • EN 60598-2-2 ; Luminaires — Part 2: Particular requirements — Section 2: Recessed luminaires
  • EN 60598-2-20 ; Luminaires — Part 2-20: Particular requirements – Lighting chains
  • EN 60598-2-20 ; Luminaires — Part 2-20: Particular requirements – Lighting chains
  • EN 60598-2-22 ; Luminaires — Part 2-22: Particular requirements – Luminaires for emergency lighting
  • EN 60598-2-23 ; Luminaires — Part 2-23: Particular requirements – Extra low-voltage lighting systems for filament lamps
  • EN 60598-2-24 ; Luminaires — Part 2: Particular requirements — Section 24: Luminaires with limited surface temperatures
  • EN 60598-2-25 ; Luminaires — Part 2-25: Particular requirements – Luminaires for use in clinical areas of hospitals and health care buildings
  • EN 60598-2-3 ; Luminaires — Part 2-3: Particular requirements – Luminaires for road and street lighting
  • EN 60598-2-4 ; Luminaires — Part 2: Particular requirements — Section 4: Portable general purpose luminaires
  • EN 60598-2-5 ; Luminaires — Part 2-5: Particular requirements – Floodlights
  • EN 60598-2-6 ; Luminaires — Part 2: Particular requirements — Section 6: Luminaires with built-in transformers or convertors for filament lamps
  • EN 60598-2-7 ; Luminaires — Part 2: Particular requirements — Section 7: Portable luminaires for garden use
  • EN 60598-2-8 ; Luminaires — Part 2-8: Particular requirements – Handlamps
  • EN 60598-2-9 ; Luminaires — Part 2: Particular requirements — Section 9: Photo and film luminaires (non-professional)
  • EN 60618 ; Inductive voltage dividers
  • EN 60645-1 ; Electroacoustics – Audiological equipment — Part 1: Pure-tone audiometers
  • EN 60645-3 ; Electroacoustics – Audiometric equipment — Part 3: Test signals of short duration
  • EN 60645-4 ; Audiometers — Part 4: Equipment for extended high-frequency audiometry
  • EN 60645-6 ; Electroacoustics – Audiometric equipment — Part 6: Instruments for the measurement of otoacoustic emissions
  • EN 60645-7 ; Electroacoustics – Audiometric equipment — Part 7: Instruments for the measurement of auditory brainstem responses
  • EN 60662 ; High-pressure sodium vapour lamps
  • EN 60664-1 ; Insulation coordination for equipment within low-voltage systems — Part 1: Principles, requirements and tests
  • EN 60664-3 ; Insulation coordination for equipment within low-voltage systems — Part 3: Use of coating, potting or moulding for protection against pollution
  • EN 60664-4 ; Insulation coordination for equipment within low-voltage systems — Part 4: Consideration of high-frequency voltage stress
  • EN 60664-5 ; Insulation coordination for equipment within low-voltage systems — Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
  • EN 60669-1 ; Switches for household and similar fixed-electrical installations — Part 1: General requirements
  • EN 60669-2-1 ; Switches for household and similar fixed electrical installations — Part 2-1: Particular requirements – Electronic switches
  • EN 60669-2-2 ; Switches for household and similar fixed electrical installations — Part 2-2: Particular requirements – Electromagnetic remote-control switches (RCS)
  • EN 60669-2-3 ; Switches for household and similar fixed electrical installations — Part 2-3: Particular requirements – Time delay switches (TDS)
  • EN 60669-2-4 ; Switches for household and similar fixed electrical installations — Part 2-4: Particular requirements – Isolating switches
  • EN 60669-2-6 ; Switches for household and similar fixed electrical installations — Part 2-6: Particular requirements – Fireman’s switches for exterior and interior signs and luminaires
  • EN 60670-1 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 1: General requirements
  • EN 60670-21 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 21: Particular requirements for boxes and enclosures with provision for suspension means
  • EN 60670-22 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 22: Particular requirements for connecting boxes and enclosures
  • EN 60670-23 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 23: Particular requirements for floor boxes and enclosures
  • EN 60688 ; Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
  • EN 60691 ; Thermal-links – Requirements and application guide
  • EN 60695-10-2 ; Fire hazard testing — Part 10-2: Abnormal heat – Ball pressure test
  • EN 60695-10-3 ; Fire hazard testing — Part 10-3: Abnormal heat – Mould stress relief distortion test
  • EN 60695-1-1 ; Fire hazard testing — Part 1-1: Guidance for assessing the fire hazard of electrotechnical products – General guidelines
  • EN 60695-11-10 ; Fire hazard testing — Part 11-10: Test flames – 50 W horizontal and vertical flame test methods
  • EN 60695-11-2 ; Fire hazard testing — Part 11-2: Test flames – 1 kW nominal pre-mixed flame – Apparatus, confirmatory test arrangement and guidance
  • EN 60695-11-20 ; Fire hazard testing — Part 11-20: Test flames – 500 W flame test methods
  • EN 60695-11-3 ; Fire hazard testing — Part 11-3: Test flames – 500 W flames – Apparatus and confirmational test methods
  • EN 60695-11-4 ; Fire hazard testing — Part 11-4: Test flames – 50 W flame – Apparatus and confirmational test method
  • EN 60695-11-5 ; Fire hazard testing — Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test arrangement and guidance
  • EN 60695-2-10 ; Fire hazard testing — Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and common test procedure
  • EN 60695-2-11 ; Fire hazard testing — Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products
  • EN 60695-2-12 ; Fire hazard testing — Part 2-12: Glowing/hot-wire based test methods – Glow-wire flammability test method for materials
  • EN 60695-2-13 ; Fire hazard testing — Part 2-13: Glowing/hot-wire based test methods – Glow-wire ignitability test method for materials
  • EN 60702-1 ; Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V — Part 1: Cables
  • EN 60702-2 ; Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V — Part 2: Terminations
  • EN 60715 ; Dimensions of low-voltage switchgear and controlgear – Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear installations
  • EN 60719 ; Calculation of the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750 V
  • EN 60728-11 ; Cable networks for television signals, sound signals and interactive services — Part 11: Safety
  • EN 60728-11 ; Cable networks for television signals, sound signals and interactive services — Part 11: Safety
  • EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
  • EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
  • EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
  • EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
  • EN 60730-2-10 ; Automatic electrical controls for household and similar use — Part 2-10: Particular requirements for motor-starting relays
  • EN 60730-2-11 ; Automatic electrical controls for household and similar use — Part 2-11: Particular requirements for energy regulators
  • EN 60730-2-12 ; Automatic electrical controls for household and similar use — Part 2-12: Particular requirements for electrically operated door locks
  • EN 60730-2-13 ; Automatic electrical controls for household and similar use — Part 2-13: Particular requirements for humidity sensing controls
  • EN 60730-2-14 ; Automatic electrical controls for household and similar use — Part 2-14: Particular requirements for electric actuators
  • EN 60730-2-15 ; Automatic electrical controls for household and similar use — Part 2-15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls
  • EN 60730-2-19 ; Automatic electrical controls for household and similar use — Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements
  • EN 60730-2-2 ; Automatic electrical controls for household and similar use — Part 2-2: Particular requirements for thermal motor protectors
  • EN 60730-2-3 ; Automatic electrical controls for household and similar use — Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
  • EN 60730-2-4 ; Automatic electrical controls for household and similar use — Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type
  • EN 60730-2-5 ; Automatic electrical controls for household and similar use — Part 2-5: Particular requirements for automatic electrical burner control systems
  • EN 60730-2-6 ; Automatic electrical controls for household and similar use — Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
  • EN 60730-2-7 ; Automatic electrical controls for household and similar use — Part 2-7: Particular requirements for timers and time switches
  • EN 60730-2-8 ; Automatic electrical controls for household and similar use — Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
  • EN 60730-2-9 ; Automatic electrical controls for household and similar use — Part 2-9: Particular requirements for temperature sensing controls
  • EN 60799 ; Electrical accessories – Cord sets and interconnection cord sets
  • EN 60811-100 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 100: General
  • EN 60811-1-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 1-1: General application – Measurement of thickness and overall dimensions – Tests for determining the mechanical properties
  • EN 60811-1-2 ; Insulating and sheathing materials of electric cables – Common test methods — Part 1-2: General application – Thermal ageing methods
  • EN 60811-1-3 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 1-3: General application – Methods for determining the density – Water absorption tests – Shrinkage test
  • EN 60811-1-4 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 1-4: General application – Tests at low temperature
  • EN 60811-201 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 201: General tests – Measurement of insulation thickness
  • EN 60811-202 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 202: General tests – Measurement of thickness of non-metallic sheath
  • EN 60811-203 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 203: General tests – Measurement of overall dimensions
  • EN 60811-2-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 2-1: Methods specific to elastomeric compounds – Ozone resistance, hot set and mineral oil immersion tests
  • EN 60811-301 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 301: Electrical tests – Measurement of the permittivity at 23 °C of filling compounds
  • EN 60811-302 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 302: Electrical tests – Measurement of the d.c. resistivity at 23 °C and 100 °C of filling compounds
  • EN 60811-3-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 3-1: Methods specific to PVC compounds – Pressure test at high temperature – Tests for resistance to cracking
  • EN 60811-3-2 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 3-2: Methods specific to PVC compounds – Loss of mass test – Thermal stability test
  • EN 60811-401 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven
  • EN 60811-402 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 402: Miscellaneous tests – Water absorption tests
  • EN 60811-403 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 403: Miscellaneous tests – Ozone resistance test on cross-linked compounds
  • EN 60811-404 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths
  • EN 60811-405 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 405: Miscellaneous tests – Thermal stability test for PVC insulations and PVC sheaths
  • EN 60811-406 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 406: Miscellaneous tests – Resistance to stress cracking of polyethylene and polypropylene compounds
  • EN 60811-407 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 407: Miscellaneous tests – Measurement of mass increase of polyethylene and polypropylene compounds
  • EN 60811-408 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 408: Miscellaneous tests – Long-term stability test of polyethylene and polypropylene compounds
  • EN 60811-409 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 409: Miscellaneous tests – Loss of mass test for thermoplastic insulations and sheaths
  • EN 60811-4-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 4-1: Methods specific to polyethylene and polypropylene compounds – Resistance to environmental stress cracking – Measurement of the melt flow index – Carbon black and/or mineral filler content measurement in polyethylene by direct combustion – Measurement of carbon black content by thermogravimetric analysis (TGA) – Assessment of carbon black dispersion in polyethylene using a microscope
  • EN 60811-410 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 410: Miscellaneous tests – Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors
  • EN 60811-411 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 411: Miscellaneous tests – Low-temperature brittleness of filling compounds
  • EN 60811-412 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 412: Miscellaneous tests – Thermal ageing methods – Ageing in an air bomb
  • EN 60811-4-2 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 4-2: Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature – Wrapping test after conditioning at elevated temperature – Wrapping test after thermal ageing in air – Measurement of mass increase – Long-term stability test – Test method for copper-catalyzed oxidative degradation
  • EN 60811-501 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 501: Mechanical tests – Tests for determining the mechanical properties of insulating and sheathing compounds
  • EN 60811-502 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 502: Mechanical tests – Shrinkage test for insulations
  • EN 60811-503 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 503: Mechanical tests – Shrinkage test for sheaths
  • EN 60811-504 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 504: Mechanical tests – Bending tests at low temperature for insulation and sheaths
  • EN 60811-505 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 505: Mechanical tests – Elongation at low temperature for insulations and sheaths
  • EN 60811-506 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 506: Mechanical tests – Impact test at low temperature for insulations and sheaths
  • EN 60811-507 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 507: Mechanical tests – Hot set test for cross-linked materials
  • EN 60811-508 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 508: Mechanical tests – Pressure test at high temperature for insulation and sheaths
  • EN 60811-509 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 509: Mechanical tests – Test for resistance of insulations and sheaths to cracking (heat shock test)
  • EN 60811-5-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 5-1: Methods specific to filling compounds – Drop point – Separation of oil – Lower temperature brittleness – Total acid number – Absence of corrosive components – Permittivity at 23 °C – D.C. resistivity at 23 °C and 100 °C
  • EN 60811-510 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 510: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after thermal ageing in air
  • EN 60811-511 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 511: Mechanical tests – Measurement of the melt flow index of polyethylene compounds
  • EN 60811-512 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 512: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature
  • EN 60811-513 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 513: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after conditioning
  • EN 60811-601 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 601: Physical tests – Measurement of the drop point of filling compounds
  • EN 60811-602 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 602: Physical tests – Separation of oil in filling compounds
  • EN 60811-603 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 603: Physical tests – Measurement of total acid number of filling compounds
  • EN 60811-604 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 604: Physical tests – Measurement of absence of corrosive components in filling compounds
  • EN 60811-605 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 605: Physical tests – Measurement of carbon black and/or mineral filler in polyethylene compounds
  • EN 60811-606 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 606: Physical tests – Methods for determining the density
  • EN 60811-607 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 607: Physical tests – Test for the assessment of carbon black dispersion in polyethylene and polypropylene
  • EN 60825-1 ; Safety of laser products — Part 1: Equipment classification and requirements
  • EN 60825-12 ; Safety of laser products — Part 12: Safety of free space optical communication systems used for transmission of information
  • EN 60825-2 ; Safety of laser products — Part 2: Safety of optical fibre communication systems (OFCS)
  • EN 60825-4 ; Safety of laser products — Part 4: Laser guards
  • EN 60831-1 ; Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
  • EN 60831-2 ; Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 2: Ageing test, self-healing test and destruction test
  • EN 60838-1 ; Miscellaneous lampholders — Part 1: General requirements and tests
  • EN 60838-2-1 ; Miscellaneous lampholders — Part 2: Particular requirements — Section 1: Lampholders S14
  • EN 60838-2-2 ; Miscellaneous lampholders — Part 2-2: Particular requirements – Connectors for LED-modules
  • EN 60898-1 ; Electrical accessories – Circuit breakers for overcurrent protection for household and similar installations — Part 1: Circuit-breakers for a.c. operation
  • EN 60898-2 ; Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations — Part 2: Circuit-breakers for a.c. and d.c. operation
  • EN 60931-1 ; Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
  • EN 60931-2 ; Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 2: Ageing test and destruction test
  • EN 60931-3 ; Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 3: Internal fuses
  • EN 60934 ; Circuit-breakers for equipment (CBE)
  • EN 60947-1 ; Low-voltage switchgear and controlgear — Part 1: General rules
  • EN 60947-2 ; Low-voltage switchgear and controlgear — Part 2: Circuit-breakers
  • EN 60947-3 ; Low-voltage switchgear and controlgear — Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
  • EN 60947-4-1 ; Low-voltage switchgear and controlgear — Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters
  • EN 60947-4-1 ; Low-voltage switchgear and controlgear — Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters
  • EN 60947-4-2 ; Low-voltage switchgear and controlgear — Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters
  • EN 60947-4-2 ; Low-voltage switchgear and controlgear — Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters
  • EN 60947-4-3 ; Low-voltage switchgear and controlgear — Part 4-3: Contactors and motor-starters – AC semiconductor controllers and contactors for non-motor loads
  • EN 60947-5-1 ; Low-voltage switchgear and controlgear — Part 5-1: Control circuit devices and switching elements – Electromechanical control circuit devices
  • EN 60947-5-2 ; Low-voltage switchgear and controlgear — Part 5-2: Control circuit devices and switching elements – Proximity switches
  • EN 60947-5-3 ; Low-voltage switchgear and controlgear — Part 5-3: Control circuit devices and switching elements – Requirements for proximity devices with defined behaviour under fault conditions (PDF)
  • EN 60947-5-4 ; Low-voltage switchgear and controlgear — Part 5-4: Control circuit devices and switching elements – Method of assessing the performance of low-energy contacts – Special tests
  • EN 60947-5-5 ; Low-voltage switchgear and controlgear — Part 5-5: Control circuit devices and switching elements – Electrical emergency stop device with mechanical latching function
  • EN 60947-5-7 ; Low-voltage switchgear and controlgear — Part 5-7: Control circuit devices and switching elements – Requirements for proximity devices with analogue output
  • EN 60947-5-8 ; Low-voltage switchgear and controlgear — Part 5-8: Control circuit devices and switching elements – Three-position enabling switches
  • EN 60947-5-9 ; Low-voltage switchgear and controlgear — Part 5-9: Control circuit devices and switching elements – Flow rate switches
  • EN 60947-6-1 ; Low-voltage switchgear and controlgear — Part 6-1: Multiple function equipment – Transfer switching equipment
  • EN 60947-6-2 ; Low-voltage switchgear and controlgear — Part 6-2: Multiple function equipment – Control and protective switching devices (or equipment) (CPS)
  • EN 60947-7-1 ; Low-voltage switchgear and controlgear — Part 7-1: Ancillary equipment – Terminal blocks for copper conductors
  • EN 60947-7-2 ; Low-voltage switchgear and controlgear — Part 7-2: Ancillary equipment – Protective conductor terminal blocks for copper conductors
  • EN 60947-7-3 ; Low-voltage switchgear and controlgear — Part 7-3: Ancillary equipment – Safety requirements for fuse terminal blocks
  • EN 60947-8 ; Low-voltage switchgear and controlgear — Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
  • EN 60950-1 ; Information technology equipment – Safety — Part 1: General requirements
  • EN 60950-21 ; Information technology equipment – Safety — Part 21: Remote power feeding
  • EN 60950-22 ; Information technology equipment – Safety — Part 22: Equipment installed outdoors
  • EN 60950-23 ; Information technology equipment – Safety — Part 23: Large data storage equipment
  • EN 60968 ; Self-ballasted lamps for general lighting services – Safety requirements
  • EN 60968 ; Self-ballasted lamps for general lighting services – Safety requirements
  • EN 60974-1 ; Arc welding equipment — Part 1: Welding power sources
  • EN 60974-1 ; Arc welding equipment — Part 1: Welding power sources
  • EN 60974-11 ; Arc welding equipment — Part 11: Electrode holders
  • EN 60974-11 ; Arc welding equipment — Part 11: Electrode holders
  • EN 60974-12 ; Arc welding equipment — Part 12: Coupling devices for welding cables
  • EN 60974-12 ; Arc welding equipment — Part 12: Coupling devices for welding cables
  • EN 60974-13 ; Arc welding equipment — Part 13: Welding clamp
  • EN 60974-2 ; Arc welding equipment — Part 2: Liquid cooling systems
  • EN 60974-3 ; Arc welding equipment — Part 3: Arc striking and stabilizing devices
  • EN 60974-5 ; Arc welding equipment — Part 5: Wire feeders
  • EN 60974-6 ; Arc welding equipment — Part 6: Limited duty equipment
  • EN 60974-6 ; Arc welding equipment — Part 6: Limited duty manual metal arc welding power sources
  • EN 60974-7 ; Arc welding equipment — Part 7:Torches
  • EN 60974-8 ; Arc welding equipment — Part 8: Gas consoles for welding and plasma cutting systems
  • EN 60998-1 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 1: General requirements
  • EN 60998-2-1 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units
  • EN 60998-2-2 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
  • EN 60998-2-3 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units
  • EN 60998-2-4 ; Connecting devices for low voltage circuits for household and similar purposes — Part 2-4: Particular requirements for twist-on connecting devices
  • EN 60999-1 ; Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units — Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
  • EN 60999-2 ; Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units — Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included)
  • EN 61008-1 ; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) — Part 1: General rules
  • EN 61008-1 ; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) — Part 1: General rules
  • EN 61008-2-1 ; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) — Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage
  • EN 61009-1 ; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) — Part 1: General rules
  • EN 61009-1 ; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) — Part 1: General rules
  • EN 61009-2-1 ; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) — Part 2-1: Applicability of the general rules to RCBO’s functionally independent of line voltage
  • EN 61010-031 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test
  • EN 61010-1 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 1: General requirements
  • EN 61010-1 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 1: General requirements
  • EN 61010-2-010 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-010: Particular requirements for laboratory equipment for the heating of material
  • EN 61010-2-020 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-020: Particular requirements for laboratory centrifuges
  • EN 61010-2-030 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-030: Particular requirements for testing and measuring circuits
  • EN 61010-2-032 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
  • EN 61010-2-032 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
  • EN 61010-2-033 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-033: Particular requirements for hand-held multimeters and other meters, for domestic and professional use, capable of measuring mains voltage
  • EN 61010-2-040 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials
  • EN 61010-2-051 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-051: Particular requirements for laboratory equipment for mixing and stirring
  • EN 61010-2-061 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization
  • EN 61010-2-081 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
  • EN 61010-2-091 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 2-091: Particular requirements for cabinet X-ray systems
  • EN 61028 ; Electrical measuring instruments – X-Y recorders
  • EN 61034-1 ; Measurement of smoke density of cables burning under defined conditions — Part 1: Test apparatus
  • EN 61034-2 ; Measurement of smoke density of cables burning under defined conditions — Part 2: Test procedure and requirements
  • EN 61048 ; Auxiliaries for lamps – Capacitors for use in tubular fluorescent and other discharge lamp circuits – General and safety requirements
  • EN 61050 ; Transformers for tubular discharge lamps having a no-load output voltage exceeding 1 kV (generally called neon-transformers) – General and safety requirements
  • EN 61058-1 ; Switches for appliances — Part 1: General requirements
  • EN 61058-2-1 ; Switches for appliances — Part 2-1: Particular requirements for cord switches
  • EN 61058-2-1 ; Switches for appliances — Part 2-1: Particular requirements for cord switches
  • EN 61058-2-4 ; Switches for appliances — Part 2-4: Particular requirements for independently mounted switches
  • EN 61058-2-5 ; Switches for appliances — Part 2-5: Particular requirements for change-over selectors
  • EN 61058-2-5 ; Switches for appliances — Part 2-5: Particular requirements for change-over selectors
  • EN 61071 ; Capacitors for power electronics
  • EN 61095 ; Electromechanical contactors for household and similar purposes
  • EN 61131-2 ; Programmable controllers — Part 2: Equipment requirements and tests
  • EN 61138 ; Cables for portable earthing and short-circuiting equipment
  • EN 61140 ; Protection against electric shock – Common aspects for installation and equipment
  • EN 61143-1 ; Electrical measuring instruments – X-t recorders — Part 1: Definitions and requirements
  • EN 61143-2 ; Electrical measuring instruments – X-t recorders — Part 2: Recommended additional test methods
  • EN 61167 ; Metal halide lamps
  • EN 61184 ; Bayonet lampholders
  • EN 61187 ; Electrical and electronic measuring equipment – Documentation
  • EN 61195 ; Double-capped fluorescent lamps – Safety specifications
  • EN 61199 ; Single-capped fluorescent lamps – Safety specifications
  • EN 61199 ; Single-capped fluorescent lamps – Safety specifications
  • EN 61204 ; Low-voltage power supply devices, d.c. output – Performance characteristics
  • EN 61204-7 ; Low voltage power supplies, d.c. output — Part 7: Safety requirements
  • EN 61210 ; Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements
  • EN 61210 ; Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements
  • EN 61230 ; Live working – Portable equipment for earthing or earthing and short-circuiting
  • EN 61236 ; Saddles, pole clamps (stick clamps) and accessories for live working
  • EN 61242 ; Electrical accessories – Cable reels for household and similar purposes
  • EN 61243-3 ; Live working – Voltage detectors — Part 3: Two-pole low-voltage type
  • EN 61243-3 ; Live working – Voltage detectors — Part 3: Two-pole low-voltage type
  • EN 61270-1 ; Capacitors for microwave ovens — Part 1: General
  • EN 61293 ; Marking of electrical equipment with ratings related to electrical supply – Safety requirements
  • EN 61310-1 ; Safety of machinery – Indication, marking and actuation — Part 1: Requirements for visual, acoustic and tactile signals
  • EN 61310-2 ; Safety of machinery – Indication, marking and actuation — Part 2: Requirements for marking
  • EN 61310-3 ; Safety of machinery – Indication, marking and actuation — Part 3: Requirements for the location and operation of actuators
  • EN 61316 ; Industrial cable reels
  • EN 61347-1 ; Lamp controlgear — Part 1: General and safety requirements
  • EN 61347-2-10 ; Lamp controlgear — Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes)
  • EN 61347-2-11 ; Lamp controlgear — Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires
  • EN 61347-2-12 ; Lamp controlgear — Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
  • EN 61347-2-13 ; Lamp controlgear — Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules
  • EN 61347-2-2 ; Lamp controlgear — Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
  • EN 61347-2-2 ; Lamp controlgear — Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
  • EN 61347-2-3 ; Lamp control gear — Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps
  • EN 61347-2-3 ; Lamp controlgear — Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps
  • EN 61347-2-4 ; Lamp controlgear — Part 2-4: Particular requirements for d.c. supplied electronic ballasts for general lighting
  • EN 61347-2-7 ; Lamp controlgear — Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)
  • EN 61347-2-7 ; Lamp controlgear — Part 2-7: Particular requirements for d.c. supplied electronic ballasts for emergency lighting
  • EN 61347-2-8 ; Lamp controlgear — Part 2-8: Particular requirements for ballasts for fluorescent lamps
  • EN 61347-2-9 ; Lamp controlgear — Part 2-9: Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps)
  • EN 61347-2-9 ; Lamp controlgear — Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
  • EN 61386-1 ; Conduit systems for cable management — Part 1: General requirements
  • EN 61386-21 ; Conduit systems for cable management — Part 21: Particular requirements – Rigid conduit systems
  • EN 61386-22 ; Conduit systems for cable management — Part 22: Particular requirements – Pliable conduit systems
  • EN 61386-23 ; Conduit systems for cable management — Part 23: Particular requirements – Flexible conduit systems
  • EN 61386-24 ; Conduit systems for cable management — Part 24: Particular requirements – Conduit systems buried underground
  • EN 61386-25 ; Conduit systems for cable management — Part 25: Particular requirements – Conduit fixing devices
  • EN 61439-1 ; Low-voltage switchgear and controlgear assemblies — Part 1: General rules
  • EN 61439-1 ; Low-voltage switchgear and controlgear assemblies — Part 1: General rules
  • EN 61439-2 ; Low-voltage switchgear and controlgear assemblies — Part 2: Power switchgear and controlgear assemblies
  • EN 61439-2 ; Low-voltage switchgear and controlgear assemblies — Part 2: Power switchgear and controlgear assemblies
  • EN 61439-3 ; Low-voltage switchgear and controlgear assemblies — Part 3: Distribution boards intended to be operated by ordinary persons (DBO)
  • EN 61439-4 ; Low-voltage switchgear and controlgear assemblies — Part 4: Particular requirements for assemblies for construction sites (ACS)
  • EN 61439-5 ; Low-voltage switchgear and controlgear assemblies — Part 5: Assemblies for power distribution in public networks
  • EN 61439-6 ; Low-voltage switchgear and controlgear assemblies — Part 6: Busbar trunking systems (busways)
  • EN 61534-1 ; Powertrack systems — Part 1: General requirements
  • EN 61534-1 ; Powertrack systems — Part 1: General requirements
  • EN 61534-21 ; Powertrack systems — Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting
  • EN 61534-22 ; Powertrack systems — Part 22: Particular requirements for powertrack systems intended for on floor or under floor installation
  • EN 61535 ; Installation couplers intended for permanent connection in fixed installations
  • EN 61537 ; Cable management – Cable tray systems and cable ladder systems
  • EN 61549 ; Miscellaneous lamps
  • EN 61557-1 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 1: General requirements
  • EN 61557-10 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 10: Combined measuring equipment for testing, measuring or monitoring of protective measures
  • EN 61557-11 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems
  • EN 61557-12 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 12: Performance measuring and monitoring devices (PMD)
  • EN 61557-13 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems
  • EN 61557-2 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 2: Insulation resistance
  • EN 61557-3 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 3: Loop impedance
  • EN 61557-4 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 4: Resistance of earth connection and equipotential bonding
  • EN 61557-5 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 5: Resistance to earth
  • EN 61557-6 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
  • EN 61557-7 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 7: Phase sequence
  • EN 61557-8 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 8: Insulation monitoring devices for IT systems
  • EN 61557-9 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 9: Equipment for insulation fault location in IT systems
  • EN 61558-1 ; Safety of power transformers, power supplies, reactors and similar products — Part 1: General requirements and tests
  • EN 61558-1 ; Safety of power transformers, power supply units and similar — Part 1: General requirements and tests
  • EN 61558-2-1 ; Safety of power transformers, power supplies, reactors and similar products — Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications
  • EN 61558-2-12 ; Safety of power transformers, power supply units and similar devices — Part 2-12: Particular requirements for constant voltage transformers
  • EN 61558-2-12 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage
  • EN 61558-2-13 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers
  • EN 61558-2-14 ; Safety of transformers, reactors, power supply units and combination thereof — Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers
  • EN 61558-2-15 ; Safety of power transformers, power supply units and similar — Part 2-15: Particular requirements for isolating transformers for the supply of medical locations
  • EN 61558-2-15 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations
  • EN 61558-2-16 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
  • EN 61558-2-2 ; Safety of power transformers, power supplies, reactors and similar products — Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers
  • EN 61558-2-20 ; Safety of power transformers, power supply units and similar devices — Part 2-20: Particular requirements for small reactors
  • EN 61558-2-20 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-20: Particular requirements and tests for small reactors
  • EN 61558-2-23 ; Safety of power transformers, power supply units and similar devices — Part 2-23: Particular requirements for transformers for construction sites
  • EN 61558-2-23 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites
  • EN 61558-2-3 ; Safety of power transformers, power supply units and similar devices — Part 2-3: Particular requirements for ignition transformers for gas and oil burners
  • EN 61558-2-3 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners
  • EN 61558-2-4 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers
  • EN 61558-2-5 ; Safety of power transformers, power supply units and similar — Part 2-5: Particular requirements for shaver transformers and shaver supply units
  • EN 61558-2-5 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-5: Particular requirements and tests for transformer for shavers, power supply units for shavers and shaver supply units
  • EN 61558-2-6 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
  • EN 61558-2-7 ; Safety of power transformers, power supplies, reactors and similar products — Part 2-7: Particular requirements and tests for transformers and power supplies for toys
  • EN 61558-2-8 ; Safety of power transformers, power supply units and similar — Part 2-8: Particular requirements for bell and chime transformers
  • EN 61558-2-8 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes
  • EN 61558-2-9 ; Safety of power transformers, power supply units and similar products — Part 2-9: Particular requirements for transformers for class III handlamps for tungsten filament lamps
  • EN 61558-2-9 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps
  • EN 61643-11 ; Low-voltage surge protective devices — Part 11: Surge protective devices connected to low-voltage power systems – Requirements and test methods
  • EN 61643-11 ; Low-voltage surge protective devices — Part 11: Surge protective devices connected to low-voltage power systems – Requirements and tests
  • EN 61643-21 ; Low voltage surge protective devices — Part 21: Surge protective devices connected to telecommunications and signalling networks – Performance requirements and testing methods
  • EN 61730-1 ; Photovoltaic (PV) module safety qualification — Part 1: Requirements for construction
  • EN 61730-2 ; Photovoltaic (PV) module safety qualification — Part 2: Requirements for testing
  • EN 61770 ; Electric appliances connected to the water mains – Avoidance of backsiphonage and failure of hose-sets
  • EN 61800-5-1 ; Adjustable speed electrical power drive systems — Part 5-1: Safety requirements – Electrical, thermal and energy
  • EN 61812-1 ; Specified time relays for industrial use — Part 1: Requirements and tests
  • EN 61812-1 ; Time relays for industrial and residential use — Part 1: Requirements and tests
  • EN 61851-1 ; Electric vehicle conductive charging system — Part 1: General requirements
  • EN 61851-1 ; Electric vehicle conductive charging system — Part 1: General requirements
  • EN 61851-21 ; Electric vehicle conductive charging system — Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply
  • EN 61851-22 ; Electric vehicle conductive charging system — Part 22: AC electric vehicle charging station
  • EN 61869-1 ; Instrument transformers — Part 1: General requirements
  • EN 61869-2 ; Instrument transformers — Part 2: Additional requirements for current transformers
  • EN 61869-3 ; Instrument transformers — Part 3: Additional requirements for inductive voltage transformers
  • EN 61869-5 ; Instrument transformers — Part 5: Additional requirements for capacitor voltage transformers
  • EN 61914 ; Cable cleats for electrical installations
  • EN 61921 ; Power capacitors – Low-voltage power factor correction banks
  • EN 61995-1 ; Devices for the connection of luminaires for household and similar purposes — Part 1: General requirements
  • EN 61995-2 ; Devices for the connection of luminaires for household and similar purposes — Part 2: Standard sheets for DCL
  • EN 62020 ; Electrical accessories – Residual current monitors for household and similar uses (RCMs)
  • EN 62026-1 ; Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) — Part 1: General rules
  • EN 62026-3 ; Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) — Part 3: DeviceNet
  • EN 62031 ; LED modules for general lighting – Safety specifications
  • EN 62035 ; Discharge lamps (excluding fluorescent lamps) – Safety specifications
  • EN 62040-1 ; Uninterruptible power systems (UPS) — Part 1: General and safety requirements for UPS
  • EN 62080 ; Sound signalling devices for household and similar purposes
  • EN 62094-1 ; Indicator light units for household and similar fixed-electrical installations — Part 1: General requirements
  • EN 62109-1 ; Safety of power converters for use in photovoltaic power systems — Part 1: General requirements
  • EN 62109-2 ; Safety of power converters for use in photovoltaic power systems — Part 2: Particular requirements for inverters
  • EN 62135-1 ; Resistance welding equipment — Part 1: Safety requirements for design, manufacture and installation
  • EN 62196-1 ; Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles — Part 1: General requirements
  • EN 62196-1 ; Plugs, socket-outlets, vehicle couplers and vehicle inlets – Conductive charging of electric vehicles — Part 1: Charging of electric vehicles up to 250 A a.c. and 400 A d.c.
  • EN 62196-2 ; Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles — Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
  • EN 62208 ; Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements
  • EN 62208 ; Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements
  • EN 62233 ; Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure
  • EN 62253 ; Photovoltaic pumping systems – Design qualification and performance measurements
  • EN 62275 ; Cable management systems – Cable ties for electrical installations
  • EN 62282-3-1 ; Fuel cell technologies — Part 3-1: Stationary fuel cell power systems – Safety
  • EN 62282-3-100 ; Fuel cell technologies — Part 3-100: Stationary fuel cell power systems – Safety
  • EN 62282-3-3 ; Fuel cell technologies — Part 3-3: Stationary fuel cell power systems – Installation
  • EN 62282-3-300 ; Fuel cell technologies — Part 3-300: Stationary fuel cell power systems – Installation
  • EN 62282-5-1 ; Fuel cell technologies — Part 5-1: Portable fuel cell power systems – Safety
  • EN 62310-1 ; Static transfer systems (STS) — Part 1: General and safety requirements
  • EN 62311 ; Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300 GHz)
  • EN 62395-1 ; Electrical resistance trace heating systems for industrial and commercial applications — Part 1: General and testing requirements
  • EN 62423 ; Type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses (Type B RCCBs and Type B RCBOs)
  • EN 62423 ; Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses
  • EN 62471 ; Photobiological safety of lamps and lamp systems
  • EN 62479 ; Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz)
  • EN 62493 ; Assessment of lighting equipment related to human exposure to electromagnetic fields
  • EN 62532 ; Fluorescent induction lamps – Safety specifications
  • EN 62549 ; Articulated systems and flexible systems for cable guiding
  • EN 62560 ; Self-ballasted LED-lamps for general lighting services by voltage > 50 V – Safety specifications
  • HD 21.1 S4 ; Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation — Part 1: General requirements
  • HD 21.10 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 10: Extensible leads
  • HD 21.11 S1 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 11: Cables for luminaires
  • HD 21.12 S1 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 12: Heat-resistant flexible cables (cords)
  • HD 21.13 S1 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 13: Oil resistant PVC sheathed cables with two or more conductors
  • HD 21.14 S1 ; Cables of rated voltage up to and including 450/750 V and having thermoplastic insulation — Part 14: Flexible cables (cords), insulated and sheathed with halogen-free thermoplastic compounds
  • HD 21.15 S1 ; Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation — Part 15: Single core cables, insulated with halogen-free thermoplastic compound, for fixed wiring
  • HD 21.3 S3 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 3: Non-sheathed cables for fixed wiring
  • HD 21.4 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 4: Sheathed cables for fixed wiring
  • HD 21.5 S3 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 5: Flexible cables (cords)
  • HD 21.7 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 7: Single core non-sheathed cables for internal wiring for a conductor temperature of 90° C
  • HD 21.8 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 8: Single core non-sheathed cables for decorative chains
  • HD 21.9 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 9: Single core non-sheathed cable for installation at low temperatures
  • HD 22.1 S4 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 1: General requirements
  • HD 22.10 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 10: EPR insulated and polyurethane sheathed flexible cables
  • HD 22.11 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 11: EVA cords and flexible cables
  • HD 22.12 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 12: Heat resistant EPR cords and flexible cables
  • HD 22.13 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 13: Halogen-free flexible cables having low emission of smoke
  • HD 22.15 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 15: Multicore cables insulated and sheathed with heat resistant silicone rubber
  • HD 22.3 S4 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 3: Heat resistant silicone rubber insulated cables
  • HD 22.4 S4 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 4: Cords and flexible cables
  • HD 22.6 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 6: Arc welding cables
  • HD 22.7 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 7: Cables with increased heat resistance for internal wiring for a conductor temperature of 110 °C
  • HD 22.8 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 8: Polychloroprene or equivalent synthetic elastomer sheathed cable for decorative chains
  • HD 22.9 S3 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 9: Single core halogen-free non-sheathed cables for fixed wiring having low emission of smoke
  • HD 308 S2 ; Identification of cores in cables and flexible cords
  • HD 361 S3 ; System for cable designation
  • HD 368 S1 ; Direct acting recording electrical measuring instruments and their accessories
  • HD 516 S2 ; Guide to use of low voltage harmonized cables
  • HD 549 S1 ; Conference systems – Electrical and audio requirements
  • HD 597 S1 ; Coupling capacitors and capacitor dividers
  • HD 60269-2 ; Low-voltage fuses — Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to J
  • HD 60269-2 ; Low-voltage fuses — Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to J
  • HD 60269-3 ; Low-voltage fuses — Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) – Examples of standardized systems of fuses A to F
  • HD 60269-3 ; Low-voltage fuses — Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) – Examples of standardized systems of fuses A to F
  • HD 603 S1 ; Distribution cables of rated voltage 0,6/1 kV
  • HD 604 S1 ; 0,6/1 kV and 1,9/3,3 kV power cables with special fire performance for use in power stations
  • HD 605 S2 ; Electric cables – Additional test methods
  • HD 626 S1 ; Overhead distribution cables of rated voltage Uo/U(Um): 0,6/1 (1,2) kV
  • HD 627 S1 ; Multicore and multipair cables for installation above and below ground
  • HD 639 S1 ; Electrical accessories – Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)