Archive for category: CE Marking

3. Concrete Pipe and Precast Sections

건설자재 시험 및 인증 관련 규격목록 3

3. Concrete Pipe and Precast Sections

3-1)          ASTM C1433M – 10 ; Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)

3-2)          ASTM C14M – 07 ; Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)

3-3)          ASTM C361M – 08 ; Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Metric)

3-4)          ASTM C444M – 03(2009) ; Standard Specification for Perforated Concrete Pipe (Metric)

3-5)          ASTM C478M – 09 ; Standard Specification for Precast Reinforced Concrete Manhole Sections (Metric)

3-6)          ASTM C507M – 10a ; Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)

3-7)          ASTM C654M – 05a ; Standard Specification for Porous Concrete Pipe (Metric)

3-8)          ASTM C655M – 09 ; Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)

3-9)          ASTM C76M – 10a ; Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)

3-10)        ASTM C858 – 10 ; Standard Specification for Underground Precast Concrete Utility Structures

3-11)        ASTM C891 – 09 ; Standard Practice for Installation of Underground Precast Concrete Utility Structures

3-12)        ASTM C913 – 08 ; Standard Specification for Precast Concrete Water and Wastewater Structures

3-13)        ASTM C924M – 02(2009) ; Standard Practice for Testing Concrete Pipe Sewer Lines by Low-Pressure Air Test Method (Metric)

3-14)        BDS 1626:1999 ; Concrete pipes (with and without) reinforcement

3-15)        IS 1916:1989 ; Specification for steel cylinder pipewith concrete lining and coating(first revision)

3-16)        IS 3597:1998 ; Methods of test for concrete pipes (second revision)

3-17)        IS 4350:1967 ; Specification for concrete porous pipes for under drainage

3-18)        IS 458:2003 ; Specification for precast concrete pipes (with and without reinforcement) (fourth revision)

3-19)        IS 7319:1974 ; Specification for perforated concrete pipes

3-20)        IS 7322:1985 ; Specification for specials for steel cylinder reinforced concrete pipes (first revision)

3-21)        IS 784:2001 ; Specification for prestressed concrete pipes (including specials) (second revision)

2. CEMENT AND CONCRETE

건설자재 시험 및 인증 관련 규격목록 2

2. CEMENT AND CONCRETE

2-1)          ASTM C172 – 08 ; Standard Practice for Sampling Freshly Mixed Concrete

2-2)          ASTM C192 / C192M – 07 ; Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory

2-3)          ASTM C31 / C31M – 09 ; Standard Practice for Making and Curing Concrete Test Specimens in the Field

2-4)          ASTM C317 / C317M – 00(2005) ; Standard Specification for Gypsum Concrete

2-5)          ASTM C39 / C39M – 09a ; Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens

2-6)          ASTM C42 / C42M – 04 ; Standard Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete

2-7)          ASTM C496 / C496M – 04e1 ; Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens

2-8)          ASTM C617 – 09a ; Standard Practice for Capping Cylindrical Concrete Specimens

2-9)          ASTM C685 / C685M – 10 ; Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing

2-10)        ASTM C78 – 09 ; Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)

2-11)        ASTM C94 / C94M – 09a ; Standard Specification for Ready-Mixed Concrete

2-12)        ASTM C989 – 09a ; Standard Specification for Slag Cement for Use in Concrete and Mortars

2-13)        BDS 240:1963 ; Specification for Plain Cold Drawn Steel Wire for Prestressed Concrete;

2-14)        BDS 243:1963 ; Specification for Coarse and Fine Aggregates from Natural Sources for Concrete;

2-15)        BDS 279:1963 ; Specification for Abrasion of Coarse Aggregates by Use of Los Angeles Machine (under revision);

2-16)        BDS 281:1963 ; Specification for Organic Impurities in Sands for Concrete (under revision);

2-17)        BDS 921:1980 ; Specification for Standard Sand for Testing of Cement;

2-18)        BDS EN 934-1:2008 ; Admixtures for concrete, mortar and grout — Part 1: Common requirements

2-19)        BDS EN 934-2:2008 ; Admixtures for concrete, mortar and grout — Part 2: Concrete admixtures — Definitions, requirements, conformity, marking and

2-20)        BDS ISO 1920-10: 2011 ; Testing of Concrete — Part 10: Determination of static modulus of elasticity in compression

2-21)        BDS ISO 1920-8: 2010 ; Testing of Concrete — Part 8: Determination of drying shrinkage of concrete for samples prepared in the field or in the laboratory

2-22)        BDS ISO 1920-9: 2010 ; Testing of Concrete — Part 9: Determination of creep of concrete cylinders in compression

2-23)        BDS ISO 22965-1: 2008 ; Concrete — Part 1: Methods of specifying and guidance for the specifier

2-24)        BDS ISO 22965-2: 2008 ; Concrete — Part 2: Specification of constituent materials, production of concrete and compliance of concrete

1. Standard for Masonry

29 Nov 2014 Comments
Off

건설자재 시험 및 인증 관련 규격목록 1

1. Standards for Masonry

1-1)         ANSI A108.1-2009 ; Specifications for the Installation of Ceramic Tile with Portland Cement Mortar;

1-2)          ANSI A108.1A—2009 ; Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar

1-3)          ANSI A108.1B—2009 ; Installation of Ceramic Tile, quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latex-portland Mortar

1-4)          ASTM A1008 / A1008M – 10 ; Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable

1-5)          ASTM A183 – 03(2009) ; Standard Specification for Carbon Steel Track Bolts and Nuts

1-6)          ASTM A615 / A615M – 09b ; Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

1-7)          ASTM A706 / A706M – 09b ; Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement

1-8)          ASTM A775 / A775M – 07b ; Standard Specification for Epoxy-Coated Steel Reinforcing Bars

1-9)          ASTM A82 / A82M – 07 ; Specification for Steel Wire, Plain, for Concrete Reinforcement

1-10)        ASTM A996 / A996M – 09b ; Standard Specification for Rail-Steel and Axle-Steel Deformed

1-11)        ASTM A996 / A996M – 09b ; Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement

1-12)        ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

1-13)        ASTM C129 – 06 ; Standard Specification for Non-load bearing Concrete Masonry Units

1-14)        ASTM C144 – 04 ; Standard Specification for Aggregate for Masonry Mortar

1-15)        ASTM C150 / C150M – 09 ; Standard Specification for Portland Cement

1-16)        ASTM C207 – 06 ; Standard Specification for Hydrated Lime for Masonry Purposes

1-17)        ASTM C212 – 00(2006) ; Standard Specification for Structural Clay Facing Tile

1-18)        ASTM C270 – 08a ; Standard Specification for Mortar for Unit Masonry

1-19)        ASTM C331 – 05 ; Standard Specification for Lightweight Aggregates for Concrete Masonry Units

1-20)        ASTM C34 – 09 ; Standard Specification for Structural Clay Load-Bearing Wall Tile

1-21)        ASTM C404 – 07 ; Standard Specification for Aggregates for Masonry Grout

1-22)        ASTM C476 – 09 ; Standard Specification for Grout for Masonry

1-23)        ASTM C5-03 ; Standard Specification for Quicklime for Structural Purposes

1-24)        ASTM C55 – 09 ; Standard Specification for Concrete Building Brick

1-25)        ASTM C56 – 09 ; Standard Specification for Structural Clay Non load bearing Tile

1-26)        ASTM C595 / C595M – 10 ; Standard Specification for Blended Hydraulic Cements

1-27)        ASTM C73 – 05 ; Standard Specification for Calcium Silicate Brick (Sand-Lime Brick)

1-28)        ASTM C744 – 09 ; Standard Specification for Prefaced Concrete and Calcium

1-29)        ASTM C90 – 09 ; Standard Specification for Load bearing Concrete Masonry Units

1-30)        ASTM C90 – 09 ; Standard Specification for Load bearing Concrete Masonry Units

1-31)        ASTM C91 – 05 ; Standard Specification for Masonry Cement

1-32)        BDS 1249 : 1989 ; Acid resistant bricks. It specifies the requirements for acid-resistant bricks, dimensions, tolerances, test etc.

1-33)        BDS 1250 : 1990 ; Burnt clay facing bricks. It specifies the dimensions, quality & strength of burnt clay facing bricks used in building & other structure, physical requirements etc.

1-34)        BDS 1263 : 1990 ; Burnt Clay hollow bricks for walls & partitions it covers the dimensions, quality & strength for hollow bricks made from burnt clay & having perforations through & at right angle to the bearing surface tests.

1-35)        BDS 1264 : 1990 ; Glossary of terms relating to structural clay products. It covers the definition of common terms applicable to structural clay products, used in building & civil engineering works.

1-36)        BDS 1432 : 1993 ; Burnt clay perforated building bricks. Specifies the requirements in regard to dimensions, perforations, quality, strength and also for quality of surface in case of special grade for facing bricks of perforated burnt clay building bricks for use in walls and partitions.

1-37)        BDS 1433 : 1993 ; Dimensions quantities in general construction work. Specifies the various dimensional values in S. I units used in general construction work.

1-38)        BDS 1803 : 2008 ; Specification for Hollow Clay Bricks and Blocks

1-39)        BDS 208 : 2009 ; Specification for Common Building clay bricks (Third revision)Specifies the dimensions, quality & strength of common burnt clay bricks, methods of sampling, testing etc.

1-40)        BDS 238 ; Fireclay refractory bricks and shapes for general purposes. This Standard specifies the requirements for fireclay refractory bricks

1-41)        BDS EN 1052-3: 2009 ; Methods of test for masonry — Part 3: Determination of initial shear strength

1-42)        BDS EN 13369: 2009 ; Common rules for precast concrete products

1-43)        BDS EN 1338: 2009 ; Concrete paving blocks — Requirements and test methods

1-44)        BDS EN 1339:2009 ; Concrete paving flags — Requirements and test methods

1-45)        BDS EN 1340:2009 ; Concrete kerb units — Requirements and test methods

1-46)        BDS EN 1745: 2009 ; Masonry and masonry products — Methods for determining design thermal values

1-47)        BDS EN 197-1:2003 (Reaffirmed 2010) ; Cement Part-1 Composition, specifications and conformity criteria for common cements.

1-48)        BDS EN 771-3: 2009 ; Specification for masonry units—Part: 3 Aggregate concrete masonry units (dense and lightweight aggregates)

1-49)        BDS EN 772-1: 2009 ; Methods of test for masonry units — Part 1: Determination of compressive strength

1-50)        BDS EN 772-11: 2009 ; Methods of test for masonry units — Part 11: Determination of water absorption of aggregate concrete, autoclaved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units

1-51)        BDS EN 772-13: 2009 ; Methods of test for masonry units — Part 13: Determination of net and gross dry density of masonry units (except for natural stone)

1-52)        BDS EN 772-14: 2009 ; Methods of test for masonry units — Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units

1-53)        BDS EN 772-16: 2009 ; Methods of test for masonry units — Part 16: Determination of dimensions

1-54)        BDS EN 772-2: 2009 ; Methods of test for masonry units — Part 2: Determination of percentage area of voids in masonry units (by paper indentation)

1-55)        BDS EN 772-20: 2009 ; Methods of test for masonry units — Part 20: Determination of flatness of faces of masonry units

1-56)        BDS EN 772-6: 2009 ; Methods of test for masonry units — Part 6: Determination of bending tensile strength of aggregate concrete masonry units

Toy Safety Standards

아래는 세계 각국가별 Toy Safety Standards 목록입니다.  Down Load : toy safety standards

국가 구분

제       목

국제 표준

ISO 8124-1 : 2012
안전 완구 – 제 1 부 : 안전 측면
기계 및 물리적 특성에 관련

ISO 8124-2 : 2007
안전 완구 – 제 2 부 : 가연성

ISO 8124-3 : 2010
특정 요소의 마이그레이션

ISO 8124-4 : 2010
그네, 슬라이드 및 이와 유사한 활동 장난감
실내 및 실외 가족 가정용

IEC 62115 : 2003
전동 완구 안전

아르헨티나

MERCOSUR 해상도 N 23/04 – 장난감 안전에 관한 기술 기준 :

NM 300.1 : 2002 안전 장난감의 제 1 부 : 일반, 기계 및 물리적 특성

NM 300-1 : 2002 개정 1 개정 자석이 포함 된 장난감 직결 된 보호 팁 발사체 장난감 w / O를 저장된 에너지

NM 300-2 : 2002 안전 장난감의 제 2 부 : 가연성

NM 300-3 : 장난감 2002 안전 제 3 부 : 특정 요소의 마이그레이션

NM 300-4 : 2002 안전 장난감의 제 4 부 : 화학 및 관련 활동에 대한 실험 세트

NM 300-5 : 2002 화학 완구 (세트) 실험 세트 이외의

NM-300-6 : 2002 안전 장난감의 6 부 : 전기 장난감의 보안

 호주

IEC 62115 : 2003 – 전동 완구안전

AS / NZS ISO 8124.1 : 2010
장난감 파트 1의 안전 : 관련 안전 측면
기계적, 물리적 특성 (ISO 8124.1 :. 2,009 MOD)

AS / NZS의 ISO 8124이 2009
의 안전 완구 – 제 2 부 : 가연성

AS / NZS ISO 8124.3 : 2012
특정 요소의 안전 장난감 마이그레이션 (ISO 8124-3 : 2010, MOD)

8124.4 AS : 2003
화학 및 관련 활동을위한 장난감 – 실험 세트의 안전

8124.5 AS : 2003
안전 장난감 – 화학 완구 (세트) 실험 세트 이외의

AS / NZS ISO 8124.6 : 2011
실내 및 실외 가족 가정용 그네, 슬라이드 및 이와 유사한 활동 장난감 : 장난감 – 6 부 안전

2003 : 8124.7 AS
- 요구 사항 및 시험 방법 장난감 손가락 페인트의 안전

2008 : / NZS 8124.9 AS
장난감 – 9 부 안전 : 유기 화학 화합물  equirements

AS / NZS 8124.10 : 2008
장난감 파트 10의 안전 : 유기 화학 화합물  충분한 준비와 추출

AS / NZS 8124.11 : 2008
안전 장난감 파트 11 : 유기 화학 화합물  분석방법

AS / NZS 62115 : 2008
전동 완구 안전

브라질

MERCOSUR 해상도 N 23/04 – 장난감 안전에 관한 기술 기준 :

NM 300.1 : 2002 안전 장난감의 제 1 부 : 일반, 기계 및 물리적 특성

NM 300-1 : 2002 개정 1 개정 자석이 포함 된 장난감 직결 된 보호 팁 발사체 장난감 w / O를 저장된 에너지

NM 300-2 : 2002 안전 장난감의 제 2 부 : 가연성

NM 300-3 : 장난감 2002 안전 제 3 부 : 특정 요소의 마이그레이션

NM 300-4 : 2002 안전 장난감의 제 4 부 : 화학 및 관련 활동에 대한 실험 세트

NM 300-5 : 2002 화학 완구 (세트) 실험 세트 이외의

NM-300-6 : 2002 안전 장난감의 6 부 : 전기 장난감의 보안

캐나다

캐나다 소비자 제품 안전법 (CCPSA)

살이 포동 포동하게 찐 박제 기사 – 기술 안전 기준

유해 제품 법 – 캐나다 보건부 (Health Canada) 관할

유해 제품 (완구) 규정 CRC, 다. 931

유해 제품 (젖꼭지) 규정 : “노브 좋아요”젖꼭지 정책

유해 제품 법에 따라 유해 제품 (젖꼭지)의 광고, 판매 및 수입을 존중 규정

완구에 대한 안전 요구 사항에 대한 가이드

장난감 : 나이 Classificiation 가이드 라인

소비자 포장 및 라벨링 법 – 캐나다 산업

중국

ISO 8124-1 : 2012
의 안전 완구 – 제 1 부 : 기계적 및 물리적 특성에 관련 안전 측면

GB 9832-2007
안전 및 봉제, 봉제 및 직물 장난감의 품질

GB 5296.5-96
라벨링 및 장난감에 대한 지침

GB 6675-2003
장난감을위한 국가 안전 기술 코드

GB / T 27708-2011 (국가 자발적 표준) 팽창 장난감의 일반 기술 요구 사항

GB / T 27730-2011 (국가 자발적 표준) 완구가스 크로마토 그래피질량 분석 방법 C에서 다이 메틸 푸마 레이트의 결정.

GB / T 28495-2012 (국가 자발적 표준) 대나무와 나무 장난감에 대한 일반 기술 요구 사항

GB 28482-2012 (국가 필수 표준) 아기와 어린이를위한 깨물고 노는 장난감의 안전 요구 사항

대만

중국어 국가 표준 CNS 4797, 4798 장난감 안전 표준

CNS 십사년에서 플라스틱 장난감 15,138 프탈레이트 유모차와 유모차를위한 중국어 국가 표준 CNS 12940 장난감 제품 라벨링 기준

유럽​​ 연합 (EU)

EN 71-1는 : 기계 및 물리적 특성에 대한 2011 사양

EN 71-2 : 2011 + A1 : 2007
인화성

EN 71-3
특정 요소의 마이그레이션
(2013년 5월 개정)

EN 71-4
실험은 화학 및 관련 활동에 대한 설정
(2013년 2월)

EN 71-5
실험 세트 이외의 화학 완구 (세트)
(2013년 5월 개정)

EN 71-8 : 2011 – 8 부
가정용 활동 장난감

EN 71-12
N-니트로 소아 민과 N-nitrosatiable 물질 (2013에서 새로운 표준)

유럽 ​​표준
2003 (수정) + A1 : EN 62115 : 2005 – 전기 완구 – 안전 IEC 62115 2004

EN 62115 : 2005 / A11 : 2012 / AC : 2013

EN 62115 : 2005 / A2 : 2011 / AC : 2011

이사회 지침 (357분의 87 / EEC)
위험 모조품 지침

위원회 지침 (93 / 68 / EEC)는
CE 마킹 적합성의 부착 및 사용에 대한 규칙

이사회 지침 (48분의 2,009 / EC) 장난감 안전 지침의
참고 :  새로운 지침 20 2009 발효 20 2011 1 모든 회원국에 법적 문서가됩니다.

제품의 마케팅 의사 결정 2,008분의 768

규정 1907/2006 REACH
(화학 물질의 등록, 평가 및 허가)

분류, 표시 및 물질 및 혼합물의 포장에 규정 1272 (CLP)

지침 65분의 2,011 RoHS 준수
(전기 전자 제품 내 특정 유해 물질의 사용 제한)

지침 19분의 2,012 WEEE
(폐 전기 전자 제품)

화장품에 대한 규제 2,009분의 1,223

지침 2008 폐기물에 / 98 / EC

포장 및 포장 폐기물에 62분의 94 / EC

지시어를 87/357 / EEC, 그들보다 다른 것으로 나타나, 소비자의 건강이나 안전을 위태롭게 제품에 관한

소재와하는 조항에 규정 1935/2004은 식품과 접촉하는

식품과 접촉하는 플라스틱 재료 및 기사에 규정 10/2011

1999 / 5 / EC
라디오 – 텔레 터미널 장비 (R & TTE)

지침 2004 / 108 / EC
전자기 호환성 (EMC)

지침 66분의 2,006 / EC
배터리

지침 2006 / 95 / EC
낮은 전압

아랍 국가의 걸프 협력회의 (Gulf Cooperation Council)

적합성 평가 규정 N. BD07070502

추가 기준을 참조

홍콩

장난감과 (ASTM F963, ICTI 또는 EN-71 준수) 어린 이용 제품 안전 규정

자메이카

JS 90 : 1983
자메이카 표준 규격 장난감의 장난감의 안전을 위한

JS 일 : 제 9 부 : 1993 상품의 라벨. 9 부 : 장난감과 놀이 도구의 표시

일본

———————
특별주의 사항 : 프탈레이트 요구 사항-23 2011 8

일본 식품 위생법 (JFSL) – 제 4

일본 장난감 안전 표준, ST2012

제 1 부 – 기계 및 물리적 특성 (ISO 8124-1에 맞춰 개정)
제 2 부 – 인화성 (ISO 8124-2에 맞춰 개정)
제 3 부 – 화학적 특성

말레이시아

MS ISO 8124-1 – 2001 완구의 안전성 – 제 1 부 : 기계적 및 물리적 특성에 관한 안전 측면

MS ISO 8124-2 : 장난감의 1999 안전 – 제 2 부 : 가연성

MS ISO 8124-3 – 2002 완구의 안전성 – 제 3 부 : 특정 요소의 마이그레이션

MS 1774 제 4 부 1998 완구의 안전성 – 제 4 부 : 화학 및 관련 활동에 대한 실험 세트

MS 1774 제 5 부 1998 완구의 안전성 – 제 5 부 : experminetal 세트 이외의 화학 완구 (세트)

MS 1774 6 부 1998 완구의 안전성 – 제 6 부 : 연령 경고 표시를위한 그래픽 기호

MS 1725 – 전기 장난감 2004 안전

멕시코

NOM-252-SSA1-2011 (게재 5 월 15, 2012)
장난감 안전 및 상업 정보 – 장난감 및 학교 물질 안전. 페인트와 염료와 기사에 사용 된 금속의 생체 이용률에 대한 제한. 화학 규격 및 시험 방법.

NOM-015-SCFI-2007
장난감에 대한 라벨링

뉴질랜드

AS / NZS ISO는 8124.1 : 2002은
안전 장난감 – 기계 및 물리적 특성에 관한 안전 측면 (Amdt 1,2  통합)

AS / NZS ISO 8124.2 : 2009
완구의 안전성 – 난연성

AS / NZS ISO 8124.3 : 2003
완구의 안전성 – certin 요소의 마이그레이션

유기 화학 화합물 – - 요구 사항 2008 완구의 안전 : / NZS 8124.9 AS

AS / NZS 8124.10 : 2008 완구의 안전성 – 유기 화학 화합물 – 샘플 준비 및 추출

AS / NZS 8124.11 : 2008 안전 장난감의 – 유기 Checmical 화합물 – 분석 방법

AS 장난감 / NZS ISO 8124 안전 설정

사우디 아라비아

SSA 765-1994
놀이터 장비 부 : 일반 안전 요구 사항 SSA 1063년부터 1994년까지 장난감과 일반 안전 요구 사항 SSA 1064-1995 테스트 부품의 방법 1 : 기계 및 화학 시험 SSA 1065년에서 1995년까지 테스트 장난감 제 2의 방법 : 가연성 SSA를 1322- 1997 저전력 무선 주파수 장치

싱가포르

 

장난감 안전 기준의 경우, ISO 8124 및 표준 또는 기타 관련 해외 표준 EN 71 시리즈를 직접 참조하시기 바랍니다.

남아프리카 공화국

SANS 8124-1 : 2009 / ISO 8124-1 : 2009
완구의 안전성 – 제 1 부 : 기계적 및 물리적 특성에 관련 안전 측면 2008 / ISO 8124-2 : (SABS ISO 8124-2) SANS 8124-2 인화성 SANS 8124 -3 : 1997 / ISO 8124-3 : 1997 (SABS ISO 8124-3) 특정 요소의 마이그레이션

태국

장난감 TIS 685-2540에 대한 타이어 공업 규격 일반 요구 사항 (1997) : 제 1 부 강제 STND. (1999 년 월 발효 일 5) 2 부 : 패키지 및 라벨링 (1997) 제 3 부 : 시험 및 분석의 방법 (1997)

미국

연방 규정 코드,이를 위해 상용 사례 16 부 1000 (16CFR)

제목 15 -Commerce 및 대외 무역 장 XI – 기술 관리, 상업 부 1150 -학과 장난감의 마킹, 모조 총기

딸랑이 미국 소비자 제품 안전위원회 엔지니어링 테스트 매뉴얼

젖꼭지 미국 소비자 제품 안전위원회 엔지니어링 테스트 매뉴얼

미술 재료 만성 위험을 제시 미국 소비자 제품 안전위원회 라벨링 요구 사항 (LHAMA)

미국의 어린이 안전 보호에 관한 법률, 질식 사고보고에 대한 작은 부품 위험 경고 규칙 및 규칙

연령 결정 지침 : 장난감 특성에 어린이의 연령 관련된 및 (2002 년 9 월) 문제를 재생

장난감 안전에 ASTM F963-11 표준 소비자 안전 사양

ASTM의 F963-2011의 관련 요구 사항에 CPSC 지침

ASTM의 F834-84 (94분의 89) 장난감 가슴에 대한 표준 소비자 안전 사양

홈 놀이터 장비에 대한 ASTM F1148-09 표준 소비자 안전 사양

ASTM F1313-90 (2005) 젖꼭지에 고무 젖꼭지의 휘발성 N-니트로사민의 수준에 대한 표준 규격

세발 자전거에 대한 ANSI Z315.1-2012 미국 국가 표준 – 안전 요구 사항

ANSI / UL 696, 아홉 번째 에디션 표준 안전 전기 완구

Product introduction

단열 및 방음 방습 건축자재(Insulation Sheet)

대한건축사협회 우수추천자재

Tel : +82-(0)2-433-3045(Rep)

Low-E insulation

 

For further information, Click herehttp://ondori.com/

Low-E insulation site

AP Network Scope CE Marking CPD

아래 건설자재에 대하여  CE Marking  자문상담합니다.

Decision

Product family, product/Intended use

AVCP system

Technical specification

95/467/EC

Chimneys, flues and specific products (1/1) : – Prefabricated chimneys (storey height elements), flue liners (elements or blocks), multi-shell chimney (elements or blocks), single walled chimneys and attached chimneys (chimneys).

FPC Certification

Body (System 2+)

EN 1020:2009

EN 12446:2011

EN

13063-1:2005+A1:2007

EN

13063-2:2005+A1:2007

EN 13063-3:2007

EN 13069:2005

EN 13084-5:2005

EN

13084-5:2005/AC:2006

EN 13084-7:2012

EN 1319:2009

EN 14471:2005

EN 1457-1:2012

EN 1457-2:2012

EN 1457:1999/A1:2002

EN

1457:1999/A1:2002/AC:20

EN 1457:1999/AC:2006

EN 14989-1:2007

EN 14989-2:2007

EN 1806:2006

EN 1856-1:2009

EN 1856-2:2009

EN 1857:2010

EN 1858:2008+A1:2011

EN 416-1:2009

EN 621:2009

EN 777-1:2009

EN 777-2:2009

EN 777-3:2009

EN 777-4:2009

EN 778:2009

96/581/EC

Geotextiles (1/2) : – Geosynthetics (membranes and textiles), geotextiles, geocomposites, geogrids, geomembranes and geonets used: as fluid or gas barriers (in roads, railways, foundations and walls, drainage systems, erosion control, reservoirs and dams, canals, tunnels and underground structures, liquid waste disposal or containment, for solid waste storage or waste disposal).

FPC Certification

Body (System 2+)

EN 13257:2000

EN 13257:2000/A1:2005

EN 13257:2000/AC:2003

EN 13265:2000

EN 13265:2000/A1:2005

EN 13265:2000/AC:2003

Decision

Product family, product/Intended use

AVCP system

Technical specification

EN 13361:2004

EN 13361:2004/A1:2006

EN 13362:2005

EN 13491:2004

EN 13491:2004/A1:2006

EN 13492:2004

EN 13492:2004/A1:2006

EN 13493:2005

EN 15382:2008

96/581/EC

Geotextiles (1/2) : – Geosynthetics (membranes and textiles), geotextiles, geocomposites, geogrids, geomembranes and geonets used: as protective layer (in roads, railways, foundations and walls, drainage systems, erosion control, reservoirs and dams, canals, tunnels and underground structures, liquid waste disposal or containment, for solid waste storage or waste disposal).

FPC Certification

Body (System 2+)

EN 13249:2000

EN 13249:2000/A1:2005

EN 13250:2000

EN 13250:2000/A1:2005

EN 13251:2000

EN 13251:2000/A1:2005

EN 13252:2000

EN 13252:2000/A1:2005

EN 13253:2000

EN 13253:2000/A1:2005

EN 13254:2000

EN 13254:2000/A1:2005

EN 13254:2000/AC:2003

EN 13255:2000

EN 13255:2000/A1:2005

EN 13255:2000/AC:2003

EN 13256:2000

EN 13256:2000/A1:2005

EN 13256:2000/AC:2003

EN 13257:2000

EN 13257:2000/A1:2005

EN 13257:2000/AC:2003

EN 13265:2000

EN 13265:2000/A1:2005

EN 13265:2000/AC:2003

EN 13361:2004

EN 13361:2004/A1:2006

EN 13362:2005

EN 13491:2004

EN 13491:2004/A1:2006

EN 13492:2004

EN 13492:2004/A1:2006

EN 13493:2005

96/581/EC

Geotextiles (1/2) : – Geosynthetics (membranes and textiles), geotextiles, geocomposites, geogrids, geomembranes and geonets used: for drainage and/or filtration (in roads,

railways, foundations and walls, drainage systems, erosion control, reservoirs and dams, canals, tunnels and underground structures, liquid waste disposal or containment, for solid waste storage or waste disposal).

FPC Certification

Body (System 2+)

EN 13249:2000

EN 13249:2000/A1:2005

EN 13250:2000

EN 13250:2000/A1:2005

EN 13251:2000

EN 13251:2000/A1:2005

EN 13252:2000

EN 13252:2000/A1:2005

EN 13253:2000

EN 13253:2000/A1:2005

EN 13257:2000

EN 13257:2000/A1:2005

EN 13257:2000/AC:2003

EN 13265:2000

EN 13265:2000/A1:2005

EN 13265:2000/AC:2003

EN 13361:2004

EN 13361:2004/A1:2006

EN 13362:2005

EN 13491:2004

EN 13491:2004/A1:2006

EN 13492:2004

EN 13492:2004/A1:2006

EN 13493:2005

96/581/EC

Geotextiles (1/2) : – Geosynthetics (membranes and textiles), geotextiles, geocomposites, geogrids, geomembranes and geonets used: for reinforcement (in roads, railways, foundations and walls, drainage systems, erosion control, reservoirs and dams, canals, tunnels and underground structures, liquid waste disposal or containment, for solid waste storage or waste disposal).

FPC Certification

Body (System 2+)

EN 13257:2000

EN 13257:2000/A1:2005

EN 13257:2000/AC:2003

EN 13265:2000

EN 13265:2000/A1:2005

EN 13265:2000/AC:2003

EN 13361:2004

EN 13361:2004/A1:2006

EN 13362:2005

EN 13491:2004

EN 13491:2004/A1:2006

EN 13492:2004

EN 13492:2004/A1:2006

EN 13493:2005

EN 15381:2008

97/176/EC

Structural timber products (1/3) : – Solid structural timber products: Elements (bridge elements, truss elements, sleepers, floor elements, wall elements, roof elements such as beams, arches, joists, rafters, columns, poles, piles) (bridges, railtracks and buildings).

FPC Certification

Body (System 2+)

EN

14081-1:2005+A1:2011

EN 14229:2010

EN 14250:2010

97/176/EC

Structural timber products (1/3) : – Solid structural timber products; Kits (trusses, floors, walls, roofs, frames) (bridges, railtracks and buildings).

FPC Certification

Body (System 2+)

EN 14250:2010

97/462/EC

Wood-based panels (1/2) : – Unfaced overlaid and veneered or coated wood-based panels (for structural elements in internal or external applications).

FPC Certification

Body (System 2+)

EN 13986:2004

97/555/EC

Cements, building limes and other hydraulic binders : – Building limes, including:<BR>-Calcium limes,<BR>-Dolomitic limes,<BR>-Hydraulic limes (preparation of concrete, mortar, grout and other mixes for construction and for the

manufacture of construction products).

FPC Certification

Body (System 2+)

EN 459-1:2010

97/555/EC

Cements, building limes and other hydraulic binders : -

FPC Certification

EN 15368:2008+A1:2010

 

Hydraulic road binders (preparation of concrete, mortar, grout and other mixes for road bases stabilisation).

Body (System 2+)

97/740/EC

Masonry and related products (1/3) : – Masonry units category

I (in walls, columns and partitions).

FPC Certification

Body (System 2+)

EN 771-1:2011

EN 771-2:2011

EN 771-3:2011

EN 771-4:2011

EN 771-5:2011

EN 771-6:2011

97/740/EC

Masonry and related products (1/3) : – Factory-made, designed masonry mortars (in walls, columns and partitions).

FPC Certification

Body (System 2+)

EN 998-2:2010

98/214/EC

Structural metallic products and ancillaries (1/4) : – Structural metallic sections/profiles: hot rolled, cold formed or otherwise produced sections/profiles with various shapes (T, L, H, U, Z, I, channels, angle, hollow, tubes), flat products (plate, sheet, strip), bars, castings, forgings made of various metallic materials, unprotected or protected against corrosion by coating (to be used in metal structures or in composite metal and concrete structures).

FPC Certification

Body (System 2+)

EN 10025-1:2004

EN 10088-4:2009

EN 10088-5:2009

EN 10210-1:2006

EN 10219-1:2006

EN 10340:2007

EN 10340:2007/AC:2008

EN 10343:2009

EN 15048-1:2007

EN 15088:2005

98/214/EC

Structural metallic products and ancillaries (2/4) : – Structural metallic construction members: finished metallic products such as trusses, girders, columns, stairs, ground piles, bearing piles and sheet piling, cut to size sections designed for certain applications, and rails and sleepers. They can be

unprotected or protected against corrosion by coating, welded or not. (for uses in work’s frames and foundations).

FPC Certification

Body (System 2+)

EN 1090-1:2009

EN 1090-1:2009+A1:2011

EN 1090-1:2009/AC:2010

98/214/EC

Structural metallic products and ancillaries (3/4) : – Welding materials (for uses in structural metallic works).

FPC Certification

Body (System 2+)

EN 13479:2004

98/214/EC

Structural metallic products and ancillaries (4/4) : – Structural connectors: metallic rivets, bolts (nuts and washers) and H.R. bolts (high strength friction grip bolts), studs, screws, railway fasteners (for uses in structural metallic works).

FPC Certification

Body (System 2+)

EN 14399-1:2005

98/598/EC

Aggregates for uses with high safety requirements (2/2) : – Fillers for bituminous mixtures and surface treatments (for roads and other civil engineering works), Aggregates for bituminous mixtures and surface treatments (for roads and other civil engineering works).

FPC Certification

Body (System 2+)

EN 13043:2002

EN 13043:2002/AC:2004

EN 13055-2:2004

98/598/EC

Aggregates for uses with high safety requirements (2/2) : – Armourstones (for hydraulic structures and other civil engineering works).

FPC Certification

Body (System 2+)

EN 13383-1:2002

EN

13383-1:2002/AC:2004

98/598/EC

Aggregates for uses with high safety requirements (2/2) : – Railway ballast (for railway works).

FPC Certification

Body (System 2+)

EN 13450:2002

EN 13450:2002/AC:2004

98/598/EC

Aggregates for uses with high safety requirements (2/2) : – Aggregates and fillers for concrete, mortar and grout (in buildings, roads and other civil engineering work).

FPC Certification

Body (System 2+)

EN 12620:2002+A1:2008

EN 13055-1:2002

EN

13055-1:2002/AC:2004

EN 13139:2002

EN 13139:2002/AC:2004

98/598/EC

Aggregates for uses with high safety requirements (2/2) : – Aggregates for unbound and hydraulically bound mixtures (for roads and other civil engineering works).

FPC Certification

Body (System 2+)

EN 13242:2002+A1:2007

98/601/EC

Road construction products (1/2) : – Bitumen (for road construction and surface treatment of roads).

FPC Certification

Body (System 2+)

EN 12591:2009

 

Decision

Product family, product/Intended use

AVCP system

Technical specification

EN 13808:2005

EN 13924:2006

EN 13924:2006/AC:2006

EN 14023:2010

EN 15322:2009

98/601/EC

Road construction products (1/2) : – Bridge deck waterproofing products and kits (for bridge decks).

FPC Certification

Body (System 2+)

EN 14695:2010

98/601/EC

Road construction products (1/2) : – Bituminous mixtures (for road construction and surface treatment of roads).

FPC Certification

Body (System 2+)

EN 13108-1:2006

EN

13108-1:2006/AC:2008

EN 13108-2:2006

EN

13108-2:2006/AC:2008

EN 13108-3:2006

EN

13108-3:2006/AC:2008

EN 13108-4:2006

EN

13108-4:2006/AC:2008

EN 13108-5:2006

EN

13108-5:2006/AC:2008

EN 13108-6:2006

EN

13108-6:2006/AC:2008

EN 13108-7:2006

EN

13108-7:2006/AC:2008

98/601/EC

Road construction products (1/2) : – Surface treatments (for surface treatments of roads).

FPC Certification

Body (System 2+)

EN 12271:2006

EN 12273:2008

99/90/EC

Membranes (1/3) : – Damp proofing sheets (in buildings).

FPC Certification

Body (System 2+)

EN 13967:2012

EN 13969:2004

EN 13969:2004/A1:2006

99/90/EC

Membranes (1/3) : – Roof sheets (in buildings).

FPC Certification

Body (System 2+)

EN 13707:2004+A2:2009

EN 13956:2012

99/93/EC

Doors, windows, shutters, blinds, gates and related building hardware (1/1) : – Doors and gates (with or without related hardware) (other declared specific uses and/or uses subject to other specific requirements, in particular noise, energy, tightness and safety-in-use (i.e. NOT for fire/smoke compartmentation, NOT for escape routes)), Windows (with or without related hardware) (any other).

Calculation body

Testing Laboratory

(System 3)

EN

14351-1:2006+A1:2010

99/94/EC

Precast normal/lightweight/autoclaved aerated concrete products (1/1) : – Precast normal/lightweight/autoclaved aerated concrete products (for structural use).

FPC Certification

Body (System 2+)

EN 1168:2005+A3:2011

EN 12737:2004+A1:2007

EN 12794:2005+A1:2007

EN

12794:2005+A1:2007/AC:2

EN 12843:2004

EN 13224:2011

EN 13225:2004

EN 13225:2004/AC:2006

EN 13693:2004+A1:2009

Decision

Product family, product/Intended use

AVCP system

Technical specification

EN 13747:2005+A2:2010

EN 13978-1:2005

EN 14843:2007

EN 14844:2006+A2:2011

EN 14991:2007

EN 14992:2007+A1:2012

EN 15037-1:2008

EN

15037-2:2009+A1:2011

EN

15037-3:2009+A1:2011

EN 15037-4:2010

EN 15050:2007+A1:2012

EN 1520:2011

EN 15258:2008

99/469/EC

Products related to concrete, mortar and grout (1/2) : – Admixtures (for concrete, mortar and grout).

FPC Certification

Body (System 2+)

EN 934-2:2009+A1:2012

EN 934-3:2009+A1:2012

EN 934-4:2009

EN 934-5:2007

99/469/EC

Products related to concrete, mortar and grout (1/2) : – Additions (type I) (for concrete, mortar and grout).

FPC Certification

Body (System 2+)

EN 12878:2005

EN 12878:2005/AC:2006

99/469/EC

Products related to concrete, mortar and grout (1/2) : – Concrete protection and repair products (for other uses in buildings and civil engineering works).

FPC Certification

Body (System 2+)

EN 1504-2:2004

EN 1504-3:2005

EN 1504-4:2004

EN 1504-5:2004

EN 1504-6:2006

EN 1504-7:2006

99/470/EC

Construction adhesives (1/2) : – Structural adhesives (for structural uses in buildings and other civil engineering works).

FPC Certification

Body (System 2+)

EN 15274:2007

EN 15275:2007

EN 15275:2007/AC:2010

 

 

건설 및 건축자재 유럽인증서 취득 대상

23 Dec 2013 Comments
Off

CE Mark  건축자재 인증 대상품 [CE Marking CPR/CPD Construction Products]

건설 및 토목 공사 목적물의 일부를 구성하는 모든 제품입니다. 일반적으로 건축, 건설 등 공사목적물이 완성되었을 때 목적물의 일부로써 존재하는 것들로 이해합니다.

대별하면, 시멘트류, 모르타르, 석고 등 단열재류, 바닥, 벽, 천정재류, 지붕재 및 누수방지재류 및 설비류,구조용 베어링류, 액체 보관 탱크류, 골재류, 충진재류, 닥트, 밸브 및 파이프, 캡류, 창호 및 도어류, 유리, 타일 및 내외장재류, 접착제류, 도로건설용 자재 및 설비, 교통제어 시스템류, 도로 표지판류, 화재감지 및 소방시설류, 건축용 하드웨어류, 화장실 변기류, 주방용 자재류, 조명용 기둥류, 도로 안전시설 자재류, 구조용 목재류, 굴뚝, 히터 등 난방 설비류, 폐수처리 설비, 상수도 설비 등이 있습니다.

인증 대상품목은 국한되지 않으나 다음과 같습니다.

1)     강철 구조물
2)     건물 보온 제품
3)     건물 홍수 방지장치
4)     건물의 유리
5)     건축용 하드웨어

6)     공기 히터, 버너 및 난방기
7)     교통 제어 장비
8)     교통 표지판
9)     구조 베어링
10)   구조용 목재

11)   구조용 볼트
12)   구조용 알루미늄 및 알루미늄 합금
13)   구조용 철강의 열연 제품
14)   구조용 주조물
15)   굴뚝

16)   금속 시트 및 루핑(지붕재)
17)   내장재(벽지, 바닥재 카펫트, 천정재 등)
18)   도로 표지판
19)   도로 바닥 마킹 자재
20)   라미네이트 바닥

21)   루핑 타일 및 피팅
22)   루핑용 조립식 부속품
23)   메탈 호스 어셈블리
24)   모듈형 타일 바닥과 계단 (내부 및 외부)
25)   방수 시트

26)   방진장치
27)   배관 시스템을 위한 접착제
28)   배수용 관이음
29)   벽돌
30)   보일러

31)   볼 밸브
32)   비 전기 자동 제어와 제연 장치
33)   비 합금 스틸 튜브
34)   사우나 스토브
35)   석고 기반의 접착제

36)   석고 plasterboard 제품
37)   섬유 석고
38)   세라믹 굴뚝 라이너
39)   세라믹 연도 블록
40)   세라믹 타일

41)   소방 댐퍼
42)   소방 시스템
43)   소방경보 장치
44)   소방용기 밸브 조립과 액츄에이터
45)   소변기

46)   소화 시스템
47)   스테인리스 파이프 피팅
48)   스틸 섬유
49)   스프링 쿨러
50)   슬레이트 및 석재

51)   시멘트
52)   아스팔트
53)   알루미늄 구조물
54)   역청탄의 혼합물
55)   연기 및 열 제어 시스템

56)   오버헤드 복사 튜브 히터 시스템
57)   외부 블라인드
58)   욕조
59)   자물쇠 래치
60)   자연석

61)   장식용 라미네이트 (HPL)
62)   점토 블록
63)   접착 적층 목재
64)   정화조 탱크
65)   조명용 기둥

66)   주방용 자재(싱크 등)
67)   지붕의 기와와 지붕 덮개
68)   지상 스토리지탱크
69)   차고 문과 게이트
70)   차량 및 보행자 영역에 대한 배수 채널

71)   창문과 문
72)   천연 석재 제품
73)   철 파이프와 피팅
74)   철도 바닥짐
75)   캐스트 폴리 우레탄 씰링

76)   커튼 웰
77)   콘크리트 블록 및 맨홀
78)   콘크리트 파이프 및 부품
79)   콘크리트
80)   파이버

81)   건축용 파이프
82)   폐수 처리 시스템
83)   건축용 폴리 (염화 비닐) (PVC-U) 프로파일
84)   건축용 폴리머 섬유
85)   프리 캐스트

86)   플라이 애쉬
87)   플러그 밸브
88)   필러 및 실런트
89)   하수도 어플 리케이션을위한 연성 철 파이프, 피팅, 부속품과 관절
90)   화재 감지 및 화재 경보 시스템

91)   Geosynthetic 관련 제품
92)   Geotextiles과 geotextile 관련 제품
93)   plasterboard 시스템을위한 금속 프레임
94)   PVC-UE 프로파일

* 위 품목외의 경우, 메일(anycerti@gmail.com)로 상담 바랍니다.

List of Norm to be applied for Machinery Directive CE Marking

23 Dec 2013 Comments
Off

CE Mark 기계지침 관련 EN 규격 목록

EN 1005-1:2001+A1:2008-Safety of machinery – Human physical performance – Part 1: Terms and definitions

EN 1005-2:2003+A1:2008-Safety of machinery – Human physical performance – Part 2: Manual handling of machinery and component parts of machinery

EN 1005-3:2002+A1:2008-Safety of machinery – Human physical performance – Part 3: Recommended force limits for machinery operation

EN 1005-4:2005+A1:2008-Safety of machinery – Human physical performance – Part 4: Evaluation of working postures and movements in relation to machinery

EN 1010-1:2004+A1:2010-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 1: Common requirements

EN 1010-2:2006+A1:2010-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 2: Printing and varnishing machines including pre-press machinery

EN 1010-3:2002+A1:2009-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 3: Cutting machines

EN 1010-4:2004+A1:2009-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 4: Bookbinding, paper converting and finishing machines

EN 1012-1:2010-Compressors and vacuum pumps – Safety requirements – Part 1: Air compressors

EN 1012-2:1996+A1:2009-Compressors and vacuum pumps – Safety requirements – Part 2: Vacuum pumps

EN 1028-1:2002+A1:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 1: Classification – General and safety requirements

EN 1028-2:2002+A1:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 2: Verification of general and safety requirements

EN 1032:2003+A1:2008-Mechanical vibration – Testing of mobile machinery in order to determine the vibration emission value

EN 1034-1:2000+A1:2010-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 1: Common requirements

EN 1034-13:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 13: Machines for de-wiring bales and units

EN 1034-14:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 14: Reel splitter

EN 1034-16:2012 (new)-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 16: Paper and board making machines

EN 1034-2:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 2: Barking drums

EN 1034-22:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 22: Wood Grinders

EN 1034-3:2011-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 3: Rereelers and winders

EN 1034-4:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 4: Pulpers and their loading facilities

EN 1034-5:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 5: Sheeters

EN 1034-6:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 6: Calender

EN 1034-7:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 7: Chests

EN 1034-8:2012 (new)-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 8: Refining plants

EN 1037:1995+A1:2008-Safety of machinery – Prevention of unexpected start-up

EN 1088:1995+A2:2008-Safety of machinery – Interlocking devices associated with guards – Principles for design and selection

EN 1093-1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 1: Selection of test methods

EN 1093-11:2001+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 11: Decontamination index

EN 1093-2:2006+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant

EN 1093-3:2006+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 3: Test bench method for the measurement of the emission rate of a given pollutant

EN 1093-4:1996+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 4: Capture efficiency of an exhaust system – Tracer method

EN 1093-6:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 6: Separation efficiency by mass, unducted outlet

EN 1093-7:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 7: Separation efficiency by mass, ducted outlet

EN 1093-8:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 8: Pollutant concentration parameter, test bench method

EN 1093-9:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 9: Pollutant concentration parameter, room method

EN 1114-1:2011-Plastics and rubber machines – Extruders and extrusion lines – Part 1: Safety requirements for extruders

EN 1114-3:2001+A1:2008-Plastics and rubber machines – Extruders and extrusion lines – Part 3: Safety requirements for haul-offs

EN 1127-1:2011-Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts and methodology

EN 1127-2:2002+A1:2008-Explosive atmospheres – Explosion prevention and protection – Part 2: Basic concepts and methodology for mining

EN 115-1:2008+A1:2010-Safety of escalators and moving walks – Part 1: Construction and installation

EN 1175-1:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 1: General requirements for battery powered trucks

EN 1175-2:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 2: General requirements of internal combustion engine powered trucks

EN 1175-3:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 3: Specific requirements for the electric power transmission systems of internal combustion engine powered trucks

EN 12001:2003+A1:2009-Conveying, spraying and placing machines for concrete and mortar – Safety requirements

EN 12012-1:2007+A1:2008-Plastics and rubber machines – Size reduction machines – Part 1: Safety requirements for blade granulators

EN 12012-3:2001+A1:2008-Plastics and rubber machines – Size reduction machines – Part 3: Safety requirements for shredders

EN 12012-4:2006+A1:2008-Plastics and rubber machines – Size reduction machines – Part 4: Safety requirements for agglomerators

EN 12013:2000+A1:2008-Plastics and rubber machines – Internal mixers – Safety requirements

EN 12016:2004+A1:2008-Electromagnetic compatibility – Product family standard for lifts, escalators and moving walks – Immunity

EN 12041:2000+A1:2009-Food processing machinery – Moulders – Safety and hygiene requirements

EN 12042:2005+A1:2010-Food processing machinery – Automatic dividers – Safety and hygiene requirements

EN 12043:2000+A1:2010-Food processing machinery – Intermediate provers – Safety and hygiene requirements

EN 12044:2005+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Cutting and punching machines – Safety requirements

EN 12053:2001+A1:2008-Safety of industrial trucks – Test methods for measuring noise emissions

EN 12077-2:1998+A1:2008-Cranes safety – Requirements for health and safety – Part 2: Limiting and indicating devices

EN 12110:2002+A1:2008-Tunnelling machines – Air locks – Safety requirements

EN 12111:2002+A1:2009-Tunnelling machines – Road headers, continuous miners and impact rippers – Safety requirements

EN 12158-1:2000+A1:2010-Builders’ hoists for goods – Part 1: Hoists with accessible platforms

EN 12158-2:2000+A1:2010-Builders’ hoists for goods – Part 2: Inclined hoists with non-accessible load carrying devices

EN 12159:2000+A1:2009-Builders hoists for persons and materials with vertically guided cages

EN 12162:2001+A1:2009-Liquid pumps – Safety requirements – Procedure for hydrostatic testing

EN 1218-1:1999+A1:2009-Safety of woodworking machines – Tenoning machines – Part 1: Single end tenoning machines with sliding table

EN 1218-2:2004+A1:2009-Safety of woodworking machines – Tenoning machines – Part 2: Double end tenoning and/or profiling machines fed by chain or chains

EN 1218-3:2001+A1:2009-Safety of woodworking machines – Tenoning machines – Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers

EN 1218-4:2004+A2:2009-Safety of woodworking machines – Tenoning machines – Part 4: Edge banding machines fed by chain(s)

EN 1218-5:2004+A1:2009-Safety of woodworking machines – Tenoning machines – Part 5: One side profiling machines with fixed table and feed rollers or feed chain

EN 12198-1:2000+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 1: General principles

EN 12198-2:2002+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 2: Radiation emission measurement procedure

EN 12198-3:2002+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 3: Reduction of radiation by attenuation or screening

EN 12203:2003+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Shoe and leather presses – Safety requirements

EN 12254:2010-Screens for laser working places – Safety requirements and testing

EN 12267:2003+A1:2010-Food processing machinery – Circular saw machines – Safety and hygiene requirements

EN 12268:2003+A1:2010-Food processing machinery – Band saw machines – Safety and hygiene requirements

EN 12301:2000+A1:2008-Plastics and rubber machines – Calenders – Safety requirements

EN 12312-1:2001+A1:2009-Aircraft ground support equipment – Specific requirements – Part 1: Passenger stairs

EN 12312-10:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 10: Container/Pallet transfer transporters

EN 12312-12:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 12: Potable water service equipment

EN 12312-13:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 13: Lavatory service equipment

EN 12312-14:2006+A1:2009-Aircraft ground support equipment – Specific requirements – Part 14: Disabled/incapacitated passenger boarding vehicles

EN 12312-15:2006+A1:2009-Aircraft ground support equipment – Specific requirements – Part 15: Baggage and equipment tractors

EN 12312-16:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 16: Air start equipment

EN 12312-17:2004+A1:2009-Aircraft ground support equipment – Specific requirements – Part 17: Air conditioning equipment

EN 12312-18:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 18: Nitrogen or Oxygen units

EN 12312-19:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions

EN 12312-2:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 2: Catering vehicles

EN 12312-20:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 20: Electrical ground power units

EN 12312-3:2003+A1:2009-Aircraft ground support equipment – Specific requirements – Part 3: Conveyor belt vehicles

EN 12312-4:2003+A1:2009-Aircraft ground support equipment – Specific requirements – Part 4: Passenger boarding bridges

EN 12312-5:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 5: Aircraft fuelling equipment

EN 12312-6:2004+A1:2009-Aircraft ground support equipment – Specific requirements – Part 6: Deicers and deicing/antiicing equipment

EN 12312-7:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 7: Air-craft movement equipment

EN 12312-8:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 8: Maintenance stairs and platforms

EN 12312-9:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 9: Container/Pallet loaders

EN 12321:2003+A1:2009-Underground mining machinery – Specification for the safety requirements of armoured face conveyors

EN 12331:2003+A2:2010-Food processing machinery – Mincing machines – Safety and hygiene requirements

EN 12336:2005+A1:2008-Tunnelling machines – Shield machines, thrust boring machines, auger boring machines, lining erection equipment – Safety requirements

EN 12348:2000+A1:2009-Core drilling machines on stand – Safety

EN 12355:2003+A1:2010-Food processing machinery – Derinding-, skinning- and membrane removal machines – Safety and hygiene requirements

EN 12385-1:2002+A1:2008-Steel wire ropes – Safety – Part 1: General requirements

EN 12385-10:2003+A1:2008-Steel wire ropes – Safety – Part 10: Spiral ropes for general structural applications

EN 12385-2:2002+A1:2008-Steel wire ropes – Safety – Part 2: Definitions, designation and classification

EN 12385-3:2004+A1:2008-Steel wire ropes – Safety – Part 3: Information for use and maintenance

EN 12385-4:2002+A1:2008-Steel wire ropes – Safety – Part 4: Stranded ropes for general lifting applications

EN 12387:2005+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Modular shoe repair equipment – Safety requirements

EN 12409:2008+A1:2011-Plastics and rubber machines – Thermoforming machines – Safety requirements

EN 12417:2001+A2:2009-Machine tools – Safety – Machining centres

EN 12418:2000+A1:2009-Masonry and stone cutting-off machines for job site – Safety

EN 12463:2004+A1:2011-Food processing machinery – Filling machines and auxiliary machines – Safety and hygiene requirements

EN 1247:2004+A1:2010-Foundry machinery – Safety requirements for ladles, pouring equipment, centrifugal casting machines, continuous and semi continuous casting machines

EN 1248:2001+A1:2009-Foundry machinery – Safety requirements for abrasive blasting equipment

EN 12505:2000+A1:2009-Food processing machinery – Centrifugal machines for processing edible oils and fats – Safety and hygiene requirements

EN 12525:2000+A2:2010-Agricultural machinery – Front loaders – Safety

EN 12545:2000+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Noise test code – Common requirements

EN 12547:1999+A1:2009-Centrifuges – Common safety requirements

EN 12549:1999+A1:2008-Acoustics – Noise test code for fastener driving tools – Engineering method

EN 12581:2005+A1:2010-Coating plants – Machinery for dip coating and electrodeposition of organic liquid coating material – Safety requirements

EN 12601:2010-Reciprocating internal combustion engine driven generating sets – Safety

EN 12621:2006+A1:2010-Machinery for the supply and circulation of coating materials under pressure – Safety requirements

EN 12622:2009-Safety of machine tools – Hydraulic press brakes

EN 12629-1:2000+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 1: Common requirements

EN 12629-2:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 2: Block making machines

EN 12629-3:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 3: Slide and turntable machines

EN 12629-4:2001+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 4:Concrete roof tile making machines

EN 12629-5-1:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-1: Pipe making machines manufacturing in the vertical axis

EN 12629-5-2:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-2: Pipe making machines manufacturing in the horizontal axis

EN 12629-5-3:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-3: Pipe prestressing machines

EN 12629-5-4:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-4: Concrete pipe coating machines

EN 12629-6:2004+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products

EN 12629-7:2004+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 7: Stationary and mobile equipment for long line manufacture of prestressed products

EN 12629-8:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)

EN 12635:2002+A1:2008-Industrial, commercial and garage doors and gates – Installation and use

EN 12643:1997+A1:2008-Earth-moving machinery – Rubber-tyred machines – Steering requirements (ISO 5010:1992 modified)

EN 12644-1:2001+A1:2008-Cranes – Information for use and testing – Part 1: Instructions

EN 12644-2:2000+A1:2008-Cranes – Information for use and testing – Part 2: Marking

EN 12649:2008+A1:2011-Concrete compactors and smoothing machines – Safety

EN 1265:1999+A1:2008-Safety of machinery – Noise test code for foundry machines and equipment

EN 12653:1999+A2:2009-Footwear, leather and imitation leather manufacturing machines – Nailing machines – Safety requirements

EN 12693:2008-Refrigerating systems and heat pumps – Safety and environmental requirements – Positive displacement refrigerant compressors

EN 12717:2001+A1:2009-Safety of machine tools – Drilling machines

EN 12733:2001+A1:2009-Agricultural and forestry machinery – Pedestrian controlled motor mowers – Safety

EN 12750:2001+A1:2009-Safety of woodworking machines – Four-sided moulding machines

EN 12753:2005+A1:2010-Thermal cleaning systems for exhaust gas from surface treatment equipment – Safety requirements

EN 12757-1:2005+A1:2010-Mixing machinery for coating materials – Safety requirements – Part 1: Mixing machinery for use in vehicle refinishing

EN 12779:2004+A1:2009-Safety of woodworking machines – Chip and dust extraction systems with fixed installation – Safety related performances and safety requirements

EN 12851:2005+A1:2010-Food processing machinery – Catering attachments for machines having an auxiliary drive hub – Safety and hygiene requirements

EN 12852:2001+A1:2010-Food processing machinery – Food processors and blenders – Safety and hygiene requirements

EN 12853:2001+A1:2010-Food processing machinery – Hand-held blenders and whisks – Safety and hygiene requirements

EN 12854:2003+A1:2010-Food processing machinery – Beam mixers – Safety and hygiene requirements

EN 12855:2003+A1:2010-Food processing machinery – Rotating bowl cutters – Safety and hygiene requirements

EN 12881-1:2005+A1:2008-Conveyor belts – Fire simulation flammability testing – Part 1: Propane burner tests

EN 12881-2:2005+A1:2008-Conveyor belts – Fire simulation flammability testing – Part 2: Large scale fire test

EN 12882:2008-Conveyor belts for general purpose use – Electrical and flammability safety requirements

EN 12921-1:2005+A1:2010-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 1: Common safety requirements

EN 12921-2:2005+A1:2008-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 2: Safety of machines using water based cleaning liquids

EN 12921-3:2005+A1:2008-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 3: Safety of machines using flammable cleaning liquids

EN 12921-4:2005+A1:2008-Machines for surface cleaning and pretreatment of industrial items using liquids and vapours – Part 4: Safety of machines using halogenated solvents

EN 12957:2001+A1:2009-Machine tools – Safety – Electro discharge machines

EN 12965:2003+A2:2009-Tractors and machinery for agriculture and forestry – Power take-off (PTO) drive shafts and their guards – Safety

EN 12978:2003+A1:2009-Industrial, commercial and garage doors and gates – Safety devices for power operated doors and gates – Requirements and test methods

EN 12981:2005+A1:2009-Coating plants – Spray booths for application of organic powder coating material – Safety requirements

EN 12984:2005+A1:2010-Food processing machinery – Portable and/or hand-guided machines and appliances with mechanically driven cutting tools – Safety and hygiene requirements

EN 1299:1997+A1:2008-Mechanical vibration and shock – Vibration isolation of machines – Information for the application of source isolation

EN 12999:2011-Cranes – Loader cranes

EN 13000:2010-Cranes – Mobile cranes

EN 13001-1:2004+A1:2009-Cranes – General design – Part 1: General principles and requirements

EN 13001-2:2011/AC:2012 (new)-EN 13001-3-1:2012 (new)

EN 13001-2:2011-Crane safety – General design – Part 2: Load actions

EN 13001-3-1:2012 (new)-Cranes – General Design – Part 3-1: Limit States and proof competence of steel structure

EN 13015:2001+A1:2008-Maintenance for lifts and escalators – Rules for maintenance instructions

EN 13019:2001+A1:2008-Machines for road surface cleaning – Safety requirements

EN 13020:2004+A1:2010-Road surface treatment machines – Safety requirements

EN 13021:2003+A1:2008-Winter service machines – Safety requirements

EN 13023:2003+A1:2010-Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment – Accuracy grades 2 and 3

EN 13035-1:2008-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 1: Storage, handling and transportation equipment inside the factory

EN 13035-11:2006+A1:2010-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 11: Drilling machines

EN 13035-2:2008-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 2: Storage, handling and transportation equipment outside the factory

EN 13035-3:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 3: Cutting machines

EN 13035-4:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 4: Tilting tables

EN 13035-5:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 5: Machines and installations for stacking and de-stacking

EN 13035-6:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 6: Machines for break-out

EN 13035-7:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 7: Cutting machines for laminated glass

EN 13035-9:2006+A1:2010-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 9: Washing installations

EN 13042-1:2007+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 1: Gob feeder

EN 13042-2:2004+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 2: Handling machines for feeding

EN 13042-3:2007+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 3: IS machines

EN 13042-5:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 5: Presses

EN 13059:2002+A1:2008-Safety of industrial trucks – Test methods for measuring vibration

EN 13102:2005+A1:2008-Ceramic machines – Safety – Loading and unloading of fine clay tiles

EN 13112:2002+A1:2009-Tannery machines – Splitting and bandknife shearing machines – Safety requirements

EN 13113:2002+A1:2010-Tannery machines – Roller coating machines – Safety requirements

EN 13114:2002+A1:2009-Tannery machines – Rotating process vessels – Safety requirements

EN 13118:2000+A1:2009-Agricultural machinery – Potato harvesting equipment – Safety

EN 13120:2009-Internal blinds – Performance requirements including safety

EN 13128:2001+A2:2009-Safety of machine tools – Milling machines (including boring machines)

EN 13135-1:2003+A1:2010-Cranes – Equipment – Part 1: Electrotechnical equipment

EN 13135-2:2004+A1:2010-Cranes – Equipment – Part 2: Non-electrotechnical equipment

EN 13140:2000+A1:2009-Agricultural machinery – Sugar beet and fodder beet harvesting equipment – Safety

EN 13155:2003+A2:2009-Cranes – Safety – Non-fixed load lifting attachments

EN 13157:2004+A1:2009-Cranes – Safety – Hand powered cranes

EN 13208:2003+A1:2010-Food processing machinery – Vegetable peelers – Safety and hygiene requirements

EN 13218:2002+A1:2008-Machine tools – Safety – Stationary grinding machines

EN 13241-1:2003+A1:2011-Industrial, commercial and garage doors and gates – Product standard – Part 1: Products without fire resistance or smoke control characteristics

EN 13288:2005+A1:2009-Food processing machinery – Bowl lifting and tilting machines – Safety and hygiene requirements

EN 13355:2004+A1:2009-Coating plants – Combined booths – Safety requirements

EN 13367:2005+A1:2008-Ceramic machines – Safety – Transfer platforms and cars

EN 13389:2005+A1:2009-Food processing machinery – Mixers with horizontal shafts – Safety and hygiene requirements

EN 13390:2002+A1:2009-Food processing machinery – Pie and tart machines – Safety and hygiene requirements

EN 13411-1:2002+A1:2008-Terminations for steel wire ropes – Safety – Part 1: Thimbles for steel wire rope slings

EN 13411-2:2001+A1:2008-Terminations for steel wire ropes – Safety – Part 2: Splicing of eyes for wire rope slings

EN 13411-3:2004+A1:2008-Terminations for steel wire ropes – Safety – Part 3: Ferrules and ferrule-securing

EN 13411-4:2011-Terminations for steel wire ropes – Safety – Part 4: Metal and resin socketing

EN 13411-5:2003+A1:2008-Terminations for steel wire ropes – Safety – Part 5: U-bolt wire rope grips

EN 13411-6:2004+A1:2008-Terminations for steel wire ropes – Safety – Part 6: Asymmetric wedge socket

EN 13411-7:2006+A1:2008-Terminations for steel wire ropes – Safety – Part 7: Symmetric wedge socket

EN 13411-8:2011-Terminations for steel wire ropes – Safety – Part 8: Swage terminals and swaging

EN 13414-1:2003+A2:2008-Steel wire rope slings – Safety – Part 1: Slings for general lifting service

EN 13414-2:2003+A2:2008-Steel wire rope slings – Safety – Part 2: Specification for information for use and maintenance to be provided by the manufacturer

EN 13414-3:2003+A1:2008-Steel wire rope slings – Safety – Part 3: Grommets and cable-laid slings

EN 13418:2004+A1:2008-Plastics and rubber machines – Winding machines for film or sheet – Safety requirements

EN 13448:2001+A1:2009-Agricultural and forestry machinery – Inter-row mowing units – Safety

EN 13457:2004+A1:2010-Footwear, leather and imitation leather goods manufacturing machines – Splitting, skiving, cutting, cementing and cement drying machines – Safety requirements

EN 13478:2001+A1:2008-Safety of machinery – Fire prevention and protection

EN 13490:2001+A1:2008-Mechanical vibration – Industrial trucks – Laboratory evaluation and specification of operator seat vibration

EN 13524:2003+A1:2009-Highway maintenance machines – Safety requirements

EN 13525:2005+A2:2009-Forestry machinery – Wood chippers – Safety

EN 13531:2001+A1:2008-Earth-moving machinery – Tip-over protection structure (TOPS) for compact excavators – Laboratory tests and performance requirements (ISO 12117:1997 modified)

EN 13534:2006+A1:2010-Food processing machinery – Curing injection machines – Safety and hygiene requirements

EN 13557:2003+A2:2008-Cranes – Controls and control stations

EN 13561:2004+A1:2008-External blinds – Performance requirements including safety

EN 13570:2005+A1:2010-Food processing machinery – Mixing machines – Safety and hygiene requirements

EN 13586:2004+A1:2008-Cranes – Access

EN 13591:2005+A1:2009-Food processing machinery – Fixed deck oven loaders – Safety and hygiene requirements

EN 13617-1:2004+A1:2009-Petrol filling stations – Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units

EN 13621:2004+A1:2010-Food processing machinery – Salad dryers – Safety and hygiene requirements

EN 13659:2004+A1:2008-Shutters – Performance requirements including safety

EN 13675:2004+A1:2010-Safety of machinery – Safety requirements for tube forming and rolling mills and their finishing line equipment

EN 13683:2003+A2:2011-Garden equipment – Integrally powered shredders/chippers – Safety

EN 13684:2004+A3:2009-Garden equipment – Pedestrian controlled lawn aerators and scarifiers – Safety

EN 13731:2007-Lifting bag systems for fire and rescue service use – Safety and performance requirements

EN 13732:2002+A2:2009-Food processing machinery – Bulk Milk Coolers on Farms – Requirements for construction, performance, suitability for use, safety and hygiene

EN 13736:2003+A1:2009-Safety of machine tools – Pneumatic presses

EN 1374:2000+A1:2010-Agricultural machinery – Silos stationary unloaders for round silos – Safety

EN 13862:2001+A1:2009-Floor cutting-off machines – Safety

EN 13870:2005+A1:2010-Food processing machinery – Chop cutting machines – Safety and hygiene requirements

EN 13871:2005+A1:2010-Food processing machinery – Cubes cutting machinery – Safety and hygiene requirements

EN 13885:2005+A1:2010-Food processing machinery – Clipping machines – Safety and hygiene requirements

EN 13886:2005+A1:2010-Food processing machinery – Cooking kettles equipped with powered stirrer and/or mixer – Safety and hygiene requirements

EN 13889:2003+A1:2008-Forged steel shackles for general lifting purposes – Dee shackles and bow shackles – Grade 6 – Safety

EN 13898:2003+A1:2009-Machine tools – Safety – Sawing machines for cold metal

EN 13951:2003+A1:2008-Liquid pumps – Safety requirements – Agrifoodstuffs equipment – Design rules to ensure hygiene in use

EN 13954:2005+A1:2010-Food processing machinery – Bread slicers – Safety and hygiene requirements

EN 13977:2011-Railway applications – Track – Safety requirements for portable machines and trolleys for construction and maintenance

EN 1398:2009-Dock levellers – Safety requirements

EN 13985:2003+A1:2009-Machine tools – Safety – Guillotine shears

EN 14010:2003+A1:2009-Safety of machinery – Equipment for power driven parking of motor vehicles – Safety and EMC requirements for design, manufacturing, erection and commissioning stages

EN 14017:2005+A2:2009-Agricultural and forestry machinery – Solid fertilizer distributors – Safety

EN 14018:2005+A1:2009-Agricultural and forestry machinery – Seed drills – Safety

EN 14033-3:2009+A1:2011-Railway applications – Track – Railbound construction and maintenance machines – Part 3: General safety requirements

EN 14043:2005+A1:2009-High rise aerial appliances for fire service use – Turntable ladders with combined movements – Safety and performance requirements and test methods

EN 14044:2005+A1:2009-High rise aerial appliances for fire service use – Turntable ladders with sequential movements – Safety and performance requirements and test methods

EN 14070:2003+A1:2009-Safety of machine tools – Transfer and special-purpose machines

EN 1417:1996+A1:2008-Plastics and rubber machines – Two roll mills – Safety requirements

EN 14238:2004+A1:2009-Cranes – Manually controlled load manipulating devices

EN 14439:2006+A2:2009-Cranes – Safety – Tower cranes

EN 14462:2005+A1:2009-Surface treatment equipment – Noise test code for surface treatment equipment including its ancillary handling equipment – Accuracy grades 2 and 3

EN 14466:2005+A1:2008-Fire-fighting pumps – Portable pumps – Safety and performance requirements, tests

EN 14492-1:2006+A1:2009-Cranes – Power driven winches and hoists – Part 1: Power driven winches

EN 14492-2:2006+A1:2009-Cranes – Power driven winches and hoists – Part 2: Power driven hoists

EN 14502-2:2005+A1:2008-Cranes – Equipment for the lifting of persons – Part 2: Elevating control stations

EN 1459:1998+A3:2012-Safety of industrial trucks – Self-propelled variable reach trucks

EN 14655:2005+A1:2010-Food processing machinery – Baguette slicers – Safety and hygiene requirements

EN 14656:2006+A1:2010-Safety of machinery – Safety requirements for extrusion presses for steel and non-ferrous metals

EN 14658:2005+A1:2010-Continuous handling equipment and systems – General safety requirements for continuous handling equipment for opencast lignite mining

EN 14673:2006+A1:2010-Safety of machinery – Safety requirements for hydraulically powered open die hot forging presses for the forging of steel and non-ferrous metals

EN 14677:2008-Safety of machinery – Secondary steelmaking – Machinery and equipment for treatment of liquid steel

EN 14681:2006+A1:2010-Safety of machinery – Safety requirements for machinery and equipment for production of steel by electric arc furnaces

EN 14710-1:2005+A2:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps without primer – Part 1: Classification, general and safety requirements

EN 14710-2:2005+A2:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps without primer – Part 2: Verification of general and safety requirements

EN 14753:2007-Safety of machinery – Safety requirements for machinery and equipment for continuous casting of steel

EN 14886:2008-Plastics and rubber machines – Bandknife cutting machines for block foams – Safety requirements

EN 14910:2007+A1:2009-Garden equipment – Walk-behind combustion engine powered trimmers – Safety

EN 1492-1:2000+A1:2008-Textile slings – Safety – Part 1: Flat woven webbing slings made of man-made fibres for general purpose use

EN 1492-2:2000+A1:2008-Textile slings – Safety – Part 2: Roundslings made of man-made fibres for general purpose use

EN 1492-4:2004+A1:2008-Textile slings – Safety – Part 4: Lifting slings for general service made from natural and man-made fibre ropes

EN 14930:2007+A1:2009-Agricultural and forestry machinery and gardening equipment – Pedestrian controlled and hand-held machines – Determination of accessibility of hot surfaces

EN 1494:2000+A1:2008-Mobile or movable jacks and associated lifting equipment

EN 1495:1997+A2:2009-Lifting platforms – Mast climbing work platforms

EN 14957:2006+A1:2010-Food processing machinery – Dishwashing machines with conveyor – Safety and hygiene requirements

EN 14958:2006+A1:2009-Food processing machinery – Machinery for grinding and processing flour and semolina – Safety and hygiene requirements

EN 14973:2006+A1:2008-Conveyor belts for use in underground installations – Electrical and flammability safety requirements

EN 14985:2012-Cranes – Slewing jib cranes

EN 15000:2008-Safety of industrial trucks – Self propelled variable reach trucks – Specification, performance and test requirements for longitudinal load moment indicators and longitudinal load moment limiters

EN 15011:2011-Cranes – Bridge and gantry cranes

EN 1501-1:2011-Refuse collection vehicles – General requirements and safety requirements – Part 1: Rear loaded refuse collection vehicles

EN 1501-2:2005+A1:2009-Refuse collection vehicles and associated lifting devices – General requirements and safety requirements – Part 2: Side loaded refuse collection vehicles

EN 1501-3:2008-Refuse collection vehicles and their associated lifting devices – General requirements and safety requirements – Part 3: Front loaded refuse collection vehicles

EN 1501-4:2007-Refuse collection vehicles and their associated lifting devices – General requirements and safety requirements – Part 4: Noise test code for refuse collection vehicles

EN 1501-5:2011-Refuse collection vehicles – General requirements and safety requirements – Part 5: Lifting devices for refuse collection vehicles

EN 15027:2007+A1:2009-Transportable wall saw and wire saw equipment for job site – Safety

EN 15056:2006+A1:2009-Cranes – Requirements for container handling spreaders

EN 15059:2009-Snow grooming equipment – Safety requirements

EN 15061:2007+A1:2008-Safety of machinery – Safety requirements for strip processing line machinery and equipment

EN 15067:2007-Plastics and rubber machines – Film converting machines for bags and sacks – Safety requirements

EN 15093:2008-Safety of Machinery – Safety requirements for hot flat rolling mills

EN 15094:2008-Safety of Machinery – Safety requirements for cold flat rolling mills

EN 15095:2007+A1:2008-Power-operated mobile racking and shelving, carousels and storage lifts – Safety requirements

EN 15162:2008-Machines and plants for mining and tooling of natural stone – Safety requirements for gang saws

EN 15163:2008-Machines and installations for the exploitation and processing of natural stone – Safety – Requirements for diamond wire saws

EN 15164:2008-Machines and plants for mining and tooling of natural stone – Safety – Requirements for chain- and belt-slotting machines

EN 15166:2008-Food processing machinery – Automatic back splitting machines of butchery carcasses – Safety and hygiene requirements

EN 1526:1997+A1:2008-Safety of industrial trucks – Additional requirements for automated functions on trucks

EN 15268:2008-Petrol filling stations – Safety requirements for the construction of submersible pump assemblies

EN 1539:2009-Dryers and ovens, in which flammable substances are released – Safety requirements

EN 1547:2001+A1:2009-Industrial thermoprocessing equipment – Noise test code for industrial thermoprocessing equipment including its ancillary handling equipment

EN 1550:1997+A1:2008-Machine-tools safety – Safety requirements for the design and construction of work holding chucks

EN 15503:2009-Garden equipment – Garden blowers, vacuums and blower/vacuums – Safety

EN 15695-1:2009-Agricultural tractors and self-propelled sprayers – Protection of the operator (driver) against hazardous substances – Part 1: Cab classification, requirements and test procedures

EN 15695-2:2009-Agricultural tractors and self-propelled sprayers – Protection of the operator (driver) against hazardous substances – Part 2: Filters, requirements and test procedures

EN 15700:2011-Safety for conveyor belts for winter sport or leisure use

EN 1570-1:2011-Safety requirements for lifting tables – Part 1: Lifting tables serving up to two fixed landings

EN 15746-2:2010+A1:2011-Railway applications – Track – Road-rail machines and associated equipment – Part 2: General safety requirements

EN 15774:2010-Food processing machinery – Machines for processing fresh and filled pasta (tagliatelle, cannelloni, ravioli, tortellini, orecchiette and gnocchi) – Safety and hygiene requirements

EN 15811:2009-Agricultural machinery – Guards for moving parts of power transmission – Guard opening with tool (ISO/TS 28923:2007 modified)

EN 15895:2011-Cartridge operated hand-held tools – Safety requirements – Fixing and hard marking tools

EN 15949:2012 (new)-Safety of machinery – Safety requirements for bar mills, structural steel mills and wire rod mills

EN 15967:2011-Determination of maximum explosion pressure and the maximum rate of pressure rise of gases and vapours

EN 15997:2011-All terrain vehicles (ATVs – Quads) – Safety requirements and test methods

EN 1612-1:1997+A1:2008-Plastics and rubber machines – Reaction moulding machines – Part 1: Safety requirements for metering and mixing units

EN 1672-2:2005+A1:2009-Food processing machinery – Basic concepts – Part 2: Hygiene requirements

EN 1673:2000+A1:2009-Food processing machinery – Rotary rack ovens – Safety and hygiene requirements

EN 1674:2000+A1:2009-Food processing machinery – Dough and pastry brakes – Safety and hygiene requirements

EN 1677-1:2000+A1:2008-Components for slings – Safety – Part 1: Forged steel components, Grade 8

EN 1677-2:2000+A1:2008-Components for slings – Safety – Part 2: Forged steel lifting hooks with latch, Grade 8

EN 1677-3:2001+A1:2008-Components for slings – Safety – Part 3: Forged steel self-locking hooks – Grade 8

EN 1677-4:2000+A1:2008-Components for slings – Safety – Part 4: Links, Grade 8

EN 1677-5:2001+A1:2008-Components for slings – Safety – Part 5: Forged steel lifting hooks with latch – Grade 4

EN 1677-6:2001+A1:2008-Components for slings – Safety – Part 6: Links – Grade 4

EN 1678:1998+A1:2010-Food processing machinery – Vegetable cutting machines – Safety and hygiene requirements

EN 1679-1:1998+A1:2011-Reciprocating internal combustion engines – Safety – Part 1: Compression ignition engines

EN 1710:2005+A1:2008-Equipment and components intended for use in potentially explosive atmospheres in underground mines

EN 1755:2000+A1:2009-Safety of industrial trucks – Operation in potentially explosive atmospheres – Use in flammable gas, vapour, mist and dust

EN 1756-1:2001+A1:2008-Tail lifts – Platform lifts for mounting on wheeled vehicles – Safety requirements – Part 1: Tail lifts for goods

EN 1756-2:2004+A1:2009-Tail lifts – Platform lifts for mounting on wheeled vehicles – Safety requirements – Part 2: Tail lifts for passengers

EN 1760-1:1997+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors

EN 1760-2:2001+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars

EN 1760-3:2004+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices

EN 1777:2010-Hydraulic platforms (HPs) for fire fighting and rescue services – Safety requirements and testing

EN 1804-1:2001+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 1: Support units and general requirements

EN 1804-2:2001+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 2: Power set legs and rams

EN 1804-3:2006+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 3: Hydraulic control systems

EN 1807:1999+A1:2009-Safety of woodworking machines – Band sawing machines

EN 1808:1999+A1:2010-Safety requirements on Suspended Access Equipment – Design calculations, stability criteria, construction – Tests

EN 1829-1:2010-High pressure water jet machines – Safety requirements – Part 1: Machines

EN 1829-2:2008-High-pressure water jet machines – Safety requirements – Part 2: Hoses, hose lines and connectors

EN 1837:1999+A1:2009-Safety of machinery – Integral lighting of machines

EN 1845:2007-Footwear manufacturing machines – Footwear moulding machines – Safety requirements

EN 1846-2:2009-Firefighting and rescue service vehicles – Part 2: Common requirements – Safety and performance

EN 1846-3:2002+A1:2008-Firefighting and rescue service vehicles – Part 3: Permanently installed equipment – Safety and performance

EN 1853:1999+A1:2009-Agricultural machinery – Trailers with tipping body – Safety

EN 1870-1:2007+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws

EN 1870-10:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines

EN 1870-11:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)

EN 1870-12:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 12: Pendulum cross-cut sawing machines

EN 1870-13:2007+A2:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 13: Horizontal beam panel sawing machines

EN 1870-14:2007+A2:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 14: Vertical panel sawing machines

EN 1870-15:2004+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 15: Multiblade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading

EN 1870-16:2005+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 16: Double mitre sawing machines for V-cutting

EN 1870-17:2007+A2:2009-Safety of woodworking machines – Circular sawing machines – Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)

EN 1870-3:2001+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches

EN 1870-4:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 4: Multiblade rip sawing machines with manual loading and/or unloading

EN 1870-5:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 5: Circular sawbenches/up-cutting cross-cut sawing machines

EN 1870-6:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading

EN 1870-7:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading

EN 1870-8:2001+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading

EN 1870-9:2000+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading

EN 1889-1:2011-Machines for underground mines – Mobile machines working underground – Safety – Part 1: Rubber tyred vehicles

EN 1889-2:2003+A1:2009-Machines for underground mines – Mobile machines working underground – Safety – Part 2: Rail locomotives

EN 1915-1:2001+A1:2009-Aircraft ground support equipment – General requirements – Part 1: Basic safety requirements

EN 1915-2:2001+A1:2009-Aircraft ground support equipment – General requirements – Part 2: Stability and strength requirements, calculations and test methods

EN 1915-3:2004+A1:2009-Aircraft ground support equipment – General requirements – Part 3: Vibration measurement methods and reduction

EN 1915-4:2004+A1:2009-Aircraft ground support equipment – General requirements – Part 4: Noise measurement methods and reduction

EN 1953:1998+A1:2009-Atomising and spraying equipment for coating materials – Safety requirements

EN 1974:1998+A1:2009-Food processing machinery – Slicing machines – Safety and hygiene requirements

EN 201:2009-Plastics and rubber machines – Injection moulding machines – Safety requirements

EN 267:2009+A1:2011-Automatic forced draught burners for liquid fuels

EN 280:2001+A2:2009-Mobile elevating work platforms – Design calculations – Stability criteria – Construction – Safety – Examinations and tests

EN 289:2004+A1:2008-Plastics and rubber machines – Presses – Safety requirements

EN 30326-1:1994-Mechanical vibration – Laboratory method for evaluating vehicle seat vibration – Part 1: Basic requirements (ISO 10326-1:1992)

EN 349:1993+A1:2008-Safety of machinery – Minimum gaps to avoid crushing of parts of the human body

EN 378-2:2008+A1:2009-Refrigerating systems and heat pumps – Safety and environmental requirements – Part 2: Design, construction, testing, marking and documentation

EN 415-1:2000+A1:2009-Packaging machines safety – Part 1: Terminology and classification of packaging machines and associated equipment

EN 415-3:1999+A1:2009-Safety of packaging machines – Part 3: Form, fill and seal machines

EN 415-5:2006+A1:2009-Safety of packaging machines – Part 5: Wrapping machines

EN 415-6:2006+A1:2009-Safety of packaging machines – Part 6: Pallet wrapping machines

EN 415-7:2006+A1:2008-Safety of packaging machines – Part 7: Group and secondary packaging machines

EN 415-8:2008-Safety of packaging machines – Part 8: Strapping machines

EN 415-9:2009-Safety of packaging machines – Part 9: Noise measurement methods for packaging machines, packaging lines and associated equipment, grade of accuracy 2 and 3

EN 422:2009-Plastics and rubber machines – Blow moulding machines – Safety requirements

EN 453:2000+A1:2009-Food processing machinery – Dough mixers – Safety and hygiene requirements

EN 454:2000+A1:2009-Food processing machinery – Planetary mixers – Safety and hygiene requirements

EN 474-1:2006+A1:2009-Earth-moving machinery – Safety – Part 1: General requirements

EN 474-10:2006+A1:2009-Earth-moving machinery – Safety – Part 10: Requirements for trenchers

EN 474-11:2006+A1:2008-Earth-moving machinery – Safety – Part 11: Requirements for earth and landfill compactors

EN 474-12:2006+A1:2008-Earth-moving machinery – Safety – Part 12: Requirements for cable excavators

EN 474-2:2006+A1:2008-Earth-moving machinery – Safety – Part 2: Requirements for tractor-dozers

EN 474-3:2006+A1:2009-Earth-moving machinery – Safety – Part 3: Requirements for loaders

EN 474-4:2006+A2:2012-Earth-moving machinery – Safety – Part 4: Requirements for backhoe loaders

EN 474-5:2006+A2:2012-Earth-moving machinery – Safety – Part 5: Requirements for hydraulic excavators

EN 474-6:2006+A1:2009-Earth-moving machinery – Safety – Part 6: Requirements for dumpers

EN 474-7:2006+A1:2009-Earth-moving machinery – Safety – Part 7: Requirements for scrapers

EN 474-8:2006+A1:2009-Earth-moving machinery – Safety – Part 8: Requirements for graders

EN 474-9:2006+A1:2009-Earth-moving machinery – Safety – Part 9: Requirements for pipelayers

EN 500-1:2006+A1:2009-Mobile road construction machinery – Safety – Part 1: Common requirements

EN 500-2:2006+A1:2008-Mobile road construction machinery – Safety – Part 2: Specific requirements for road-milling machines

EN 500-3:2006+A1:2008-Mobile road construction machinery – Safety – Part 3: Specific requirements for soil-stabilising machines and recycling machines

EN 500-4:2011-Mobile road construction machinery – Safety – Part 4: Specific requirements for compaction machines

EN 500-6:2006+A1:2008-Mobile road construction machinery – Safety – Part 6: Specific requirements for paver-finishers

EN 50223:2010-Stationary electrostatic application equipment for ignitable flock material – Safety requirements

EN 50348:2010-Stationary electrostatic application equipment for non-ignitable liquid coating material – Safety requirements

EN 50580:2012 (new)-Safety of hand-held electric motor operated tools — Particular requirements for spray guns

EN 528:2008-Rail dependent storage and retrieval equipment – Safety requirements

EN 547-1:1996+A1:2008-Safety of machinery – Human body measurements – Part 1: Principles for determining the dimensions required for openings for whole body access into machinery

EN 547-2:1996+A1:2008-Safety of machinery – Human body measurements – Part 2: Principles for determining the dimensions required for access openings

EN 547-3:1996+A1:2008-Safety of machinery – Human body measurements – Part 3: Anthropometric data

EN 574:1996+A1:2008-Safety of machinery – Two-hand control devices – Functional aspects – Principles for design

EN 60204-1:2006-Safety of machinery – Electrical equipment of machines — Part 1: General requirements

EN 60204-11:2000-Safety of machinery – Electrical equipment of machines — Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV

EN 60204-32:2008-Safety of machinery – Electrical equipment of machines — Part 32: Requirements for hoisting machines

EN 60204-33:2011-Safety of machinery – Electrical equipment of machines — Part 33: Requirements for semiconductor fabrication equipment

EN 60335-1:2012 (new)-Household and similar electrical appliances – Safety — Part 1: General requirements

EN 60335-2-67:2009-Household and similar electrical appliances – Safety — Part 2-67: Particular requirements for floor treatment and floor cleaning machines for commercial use

EN 60335-2-68:2009-Household and similar electrical appliances – Safety — Part 2-68: Particular requirements for spray extraction machines for commercial use

EN 60335-2-69:2009-Household and similar electrical appliances – Safety — Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial use

EN 60335-2-72:2009-Household and similar electrical appliances – Safety — Part 2-72: Particular requirements for automatic machines for floor treatment for commercial use

EN 60335-2-77:2010-Safety of household and similar appliances — Part 2-77: Particular requirements for pedestrian-controlled walk-behind electrically powered lawn mowers

EN 60335-2-79:2009-Household and similar electrical appliances – Safety — Part 2-79: Particular requirements for high pressure cleaners and steam cleaners

EN 60745-1:2009-Hand-held motor-operated electric tools – Safety — Part 1: General requirements

EN 60745-2-1:2010-Hand-held motor-operated electric tools – Safety — Part 2-1: Particular requirements for drills and impact drills

EN 60745-2-11:2010-Hand-held motor-operated electric tools – Safety — Part 2-11: Particular requirements for reciprocating saws (jig and sabre saws)

EN 60745-2-12:2009-Hand-held motor-operated electric tools – Safety — Part 2-12: Particular requirements for concrete vibrators

EN 60745-2-13:2009-Hand-held motor-operated electric tools – Safety — Part 2-13: Particular requirements for chain saws

EN 60745-2-14:2009-Hand-held motor-operated electric tools – Safety — Part 2-14: Particular requirements for planers

EN 60745-2-15:2009-Hand-held motor-operated electric tools – Safety — Part 2-15: Particular requirements for hedge trimmers

EN 60745-2-16:2010-Hand-held motor-operated electric tools – Safety — Part 2-16: Particular requirements for tackers

EN 60745-2-17:2010-Hand-held motor-operated electric tools – Safety — Part 2-17: Particular requirements for routers and trimmers

EN 60745-2-18:2009-Hand-held motor-operated electric tools – Safety — Part 2-18: Particular requirements for strapping tools

EN 60745-2-19:2009-Hand-held motor-operated electric tools – Safety — Part 2-19: Particular requirements for jointers

EN 60745-2-2:2010-Hand-held motor-operated electric tools – Safety — Part 2-2: Particular requirements for screwdrivers and impact wrenches

EN 60745-2-20:2009-Hand-held motor-operated electric tools – Safety — Part 2-20: Particular requirements for band saws

EN 60745-2-21:2009-Hand-held motor-operated electric tools – Safety — Part 2-21: Particular requirements for drain cleaners

EN 60745-2-22:2011-Hand-held motor-operated electric tools – Safety — Part 2-22: Particular requirements for cut-off machines

EN 60745-2-3:2011-Hand-held motor-operated electric tools – Safety — Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

EN 60745-2-4:2009-Hand-held motor-operated electric tools – Safety — Part 2-4: Particular requirements for sanders and polishers other than disk type

EN 60745-2-5:2010-Hand-held motor-operated electric tools – Safety — Part 2-5: Particular requirements for circular saws

EN 60745-2-6:2010-Hand-held motor-operated electric tools – Safety — Part 2-6: Particular requirements for hammers

EN 60745-2-8:2009-Hand-held motor-operated electric tools – Safety — Part 2-8: Particular requirements for shears and nibblers

EN 60745-2-9:2009-Hand-held motor-operated electric tools – Safety — Part 2-9: Particular requirements for tappers

EN 609-1:1999+A2:2009-Agricultural and forestry machinery – Safety of log splitters – Part 1: Wedge splitters

EN 609-2:1999+A1:2009-Agricultural and forestry machinery – Safety of log splitters – Part 2: Screw splitters

EN 61029-1:2009-Safety of transportable motor-operated electric tools — Part 1: General requirements

EN 61310-1:2008-Safety of machinery – Indication, marking and actuation — Part 1: Requirements for visual, acoustic and tactile signals

EN 61310-2:2008-Safety of machinery – Indication, marking and actuation — Part 2: Requirements for marking

EN 61310-3:2008-Safety of machinery – Indication, marking and actuation — Part 3: Requirements for the location and operation of actuators

EN 614-1:2006+A1:2009-Safety of machinery – Ergonomic design principles – Part 1: Terminology and general principles

EN 614-2:2000+A1:2008-Safety of machinery – Ergonomic design principles – Part 2: Interactions between the design of machinery and work tasks

EN 61496-1:2004-Safety of machinery – Electro-sensitive protective equipment — Part 1: General requirements and tests

EN 617:2001+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers

EN 618:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors

EN 619:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for equipment for mechanical handling of unit loads

EN 620:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for fixed belt conveyors for bulk materials

EN 62061:2005-Safety of machinery – Functional safety of safety-related electrical, electronic and programmable electronic control systems

EN 626-1:1994+A1:2008-Safety of machinery – Reduction of risks to health from hazardous substances emitted by machinery – Part 1: Principles and specifications for machinery manufacturers

EN 626-2:1996+A1:2008-Safety of machinery – Reduction of risk to health from hazardous substances emitted by machinery – Part 2: Methodology leading to verification procedures

EN 676:2003+A2:2008-Automatic forced draught burners for gaseous fuels

EN 690:1994+A1:2009-Agricultural machinery – Manure spreaders – Safety

EN 692:2005+A1:2009-Machine tools – Mechanical presses – Safety

EN 693:2001+A2:2011-Machine tools – Safety – Hydraulic presses

EN 703:2004+A1:2009-Agricultural machinery – Silage loading, mixing and/or chopping and distributing machines – Safety

EN 706:1996+A1:2009-Agricultural machinery – Vine shoot tipping machines – Safety

EN 707:1999+A1:2009-Agricultural machinery – Slurry tankers – Safety

EN 709:1997+A4:2009-Agricultural and forestry machinery – Pedestrian controlled tractors with mounted rotary cultivators, motor hoes, motor hoes with drive wheel(s) – Safety

EN 710:1997+A1:2010-Safety requirements for foundry moulding and coremaking machinery and plant associated equipment

EN 741:2000+A1:2010-Continuous handling equipment and systems – Safety requirements for systems and their components for pneumatic handling of bulk materials

EN 745:1999+A1:2009-Agricultural machinery – Rotary mowers and flail-mowers – Safety

EN 746-1:1997+A1:2009-Industrial thermoprocessing equipment – Part 1: Common safety requirements for industrial thermoprocessing equipment

EN 746-2:2010-Industrial thermoprocessing equipment – Part 2: Safety requirements for combustion and fuel handling systems

EN 746-3:1997+A1:2009-Industrial thermoprocessing equipment – Part 3: Safety requirements for the generation and use of atmosphere gases

EN 786:1996+A2:2009-Garden equipment – Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers – Mechanical safety

EN 791:1995+A1:2009-Drill rigs – Safety

EN 792-12:2000+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 12: Small circular, small oscillating and reciprocating saws

EN 792-13:2000+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 13: Fastener driving tools

EN 792-7:2001+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 7: Grinders

EN 809:1998+A1:2009-Pumps and pump units for liquids – Common safety requirements

EN 81-3:2000+A1:2008-Safety rules for the construction and installation of lifts – Part 3: Electric and hydraulic service lifts

EN 81-31:2010-Safety rules for the construction and installation of lifts – Lifts for the transport of goods only – Part 31: Accessible goods only lifts

EN 81-40:2008-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 40: Stairlifts and inclined lifting platforms intended for persons with impaired mobility

EN 81-41:2010-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 41: Vertical lifting platforms intended for use by persons with impaired mobility

EN 81-43:2009-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 43: Lifts for cranes

EN 815:1996+A2:2008-Safety of unshielded tunnel boring machines and rodless shaft boring machines for rock – Safety requirements

EN 818-1:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 1: General conditions of acceptance

EN 818-2:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 2: Medium tolerance chain for chain slings – Grade 8

EN 818-3:1999+A1:2008-Short link chain for lifting purposes – Safety – Part 3: Medium tolerance chain for chain slings – Grade 4

EN 818-4:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 4: Chain slings – Grade 8

EN 818-5:1999+A1:2008-Short link chain for lifting purposes – Safety – Part 5: Chain slings – Grade 4

EN 818-6:2000+A1:2008-Short link chain for lifting purposes – Safety – Part 6: Chain slings – Specification for information for use and maintenance to be provided by the manufacturer

EN 818-7:2002+A1:2008-Short link chain for lifting purposes – Safety – Part 7: Fine tolerance hoist chain, Grade T (Types T, DAT and DT)

EN 836:1997+A4:2011-Garden equipment – Powered lawnmowers – Safety

EN 842:1996+A1:2008-Safety of machinery – Visual danger signals – General requirements, design and testing

EN 848-1:2007+A1:2009-Safety of woodworking machines – One side moulding machines with rotating tool – Part 1: Single spindle vertical moulding machines

EN 848-2:2007+A1:2009-Safety of woodworking machines – One side moulding machines with rotating tool – Part 2: Single spindle hand fed/integrated fed routing machines

EN 848-3:2007+A2:2009-Safety of woodworking machines – One side moulding machines with rotating tools – Part 3: Numerically controlled (NC) boring and routing machines

EN 859:2007+A1:2009-Safety of woodworking machines – Hand fed surface planing machines

EN 860:2007+A1:2009-Safety of woodworking machines – One side thickness planing machines

EN 861:2007+A1:2009-Safety of woodworking machines – Surface planing and thicknessing machines

EN 869:2006+A1:2009-Safety of machinery – Safety requirements for pressure metal diecasting units

EN 894-1:1997+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 1: General principles for human interactions with displays and control actuators

EN 894-2:1997+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 2: Displays

EN 894-3:2000+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 3: Control actuators

EN 894-4:2010-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 4: Location and arrangement of displays and control actuators

EN 908:1999+A1:2009-Agricultural and forestry machinery – Reel machines for irrigation – Safety

EN 909:1998+A1:2009-Agricultural and forestry machinery – Centre pivot and moving lateral types irrigation machines – Safety

EN 930:1997+A2:2009-Footwear, leather and imitation leather goods manufacturing machines – Roughing, scouring, polishing and trimming machines – Safety requirements

EN 931:1997+A2:2009-Footwear manufacturing machines – Lasting machines – Safety requirements

EN 940:2009+A1:2012 (new)-Safety of woodworking machines – Combined woodworking machines

EN 953:1997+A1:2009-Safety of machinery – Guards – General requirements for the design and construction of fixed and movable guards

EN 972:1998+A1:2010-Tannery machines – Reciprocating roller machines – Safety requirements

EN 981:1996+A1:2008-Safety of machinery – System of auditory and visual danger and information signals

EN 996:1995+A3:2009-Piling equipment – Safety requirements

EN ISO 10218-1:2011-Robots and robotic devices – Safety requirements for industrial robots – Part 1: Robots (ISO 10218-1:2011)

EN ISO 10218-2:2011-Robots and robotic devices – Safety requirements for industrial robots – Part 2: Robot systems and integration (ISO 10218-2:2011)

EN ISO 10472-1:2008-Safety requirements for industrial laundry machinery – Part 1: Common requirements (ISO 10472-1:1997)

EN ISO 10472-2:2008-Safety requirements for industrial laundry machinery – Part 2: Washing machines and washer-extractors (ISO 10472-2:1997)

EN ISO 10472-3:2008-Safety requirements for industrial laundry machinery – Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997)

EN ISO 10472-4:2008-Safety requirements for industrial laundry machinery – Part 4: Air dryers (ISO 10472-4:1997)

EN ISO 10472-5:2008-Safety requirements for industrial laundry machinery – Part 5: Flatwork ironers, feeders and folders (ISO 10472-5:1997)

EN ISO 10472-6:2008-Safety requirements for industrial laundry machinery – Part 6: Ironing and fusing presses (ISO 10472-6:1997)

EN ISO 10517:2009-Powered hand-held hedge trimmers – Safety (ISO 10517:2009)

EN ISO 10821:2005-Industrial sewing machines – Safety requirements for sewing machines, units and systems (ISO 10821:2005)

EN ISO 11102-1:2009-Reciprocating internal combustion engines – Handle starting equipment – Part 1: Safety requirements and tests (ISO 11102-1:1997)

EN ISO 11102-2:2009-Reciprocating internal combustion engines – Handle starting equipment – Part 2: Method of testing the angle of disengagement (ISO 11102-2:1997)

EN ISO 11111-1:2009-Textile machinery – Safety requirements – Part 1: Common requirements (ISO 11111-1:2009)

EN ISO 11111-2:2005-Textile machinery – Safety requirements – Part 2: Spinning preparatory and spinning machines (ISO 11111-2:2005)

EN ISO 11111-3:2005-Textile machinery – Safety requirements – Part 3: Nonwoven machinery (ISO 11111-3:2005)

EN ISO 11111-4:2005-Textile machinery – Safety requirements – Part 4: Yarn processing, cordage and rope manufacturing machinery (ISO 11111-4:2005)

EN ISO 11111-5:2005-Textile machinery – Safety requirements – Part 5: Preparatory machinery to weaving and knitting (ISO 11111-5:2005)

EN ISO 11111-6:2005-Textile machinery – Safety requirements – Part 6: Fabric manufacturing machinery (ISO 11111-6:2005)

EN ISO 11111-7:2005-Textile machinery – Safety requirements – Part 7: Dyeing and finishing machinery (ISO 11111-7:2005)

EN ISO 11145:2008-Optics and photonics – Lasers and laser-related equipment – Vocabulary and symbols (ISO 11145:2006)

EN ISO 11148-10:2011-Hand-held non-electric power tools – Safety requirements – Part 10: Compression power tools (ISO 11148-10:2011)

EN ISO 11148-11:2011-Hand-held non-electric power tools – Safety requirements – Part 11: Nibblers and shears (ISO 11148-11:2011)

EN ISO 11148-2:2011-Hand-held non-electric power tools – Safety requirements – Part 2: Cutting-off and crimping power tools (ISO/FDIS 11148-2:2011)

EN ISO 11148-3:2010-Hand-held non-electric power tools – Safety requirements – Part 3: Drills and tappers (ISO 11148-3:2010)

EN ISO 11148-4:2010-Hand-held non-electric power tools – Safety requirements – Part 4: Non­rotary percussive power tools (ISO 11148-4:2010)

EN ISO 11148-5:2011-Hand-held non-electric power tools – Safety requirements – Part 5: Rotary percussive drills (ISO 11148-5:2011)

EN ISO 11148-6:2010-Hand-held non-electric power tools – Safety requirements – Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2010)

EN ISO 11148-8:2011-Hand-held non-electric power tools – Safety requirements – Part 8: Sanders and polishers (ISO 11148-8:2011)

EN ISO 11148-9:2011-Hand-held non-electric power tools – Safety requirements – Part 9: Die grinders (ISO 11148-9:2011)

EN ISO 11161:2007-Safety of machinery – Integrated manufacturing systems – Basic requirements (ISO 11161:2007)

EN ISO 11200:2009-Acoustics – Noise emitted by machinery and equipment – Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:1995, including Cor 1:1997)

EN ISO 11201:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)

EN ISO 11202:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)

EN ISO 11203:2009-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)

EN ISO 11204:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)

EN ISO 11205:2009-Acoustics – Noise emitted by machinery and equipment – Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity (ISO 11205:2003)

EN ISO 11252:2008-Lasers and laser-related equipment – Laser device – Minimum requirements for documentation (ISO 11252:2004)

EN ISO 11546-1:2009-Acoustics – Determination of sound insulation performances of enclosures – Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)

EN ISO 11546-2:2009-Acoustics – Determination of sound insulation performances of enclosures – Part 2: Measurements in situ (for acceptance and verification purposes) (ISO 11546-2:1995)

EN ISO 11553-1:2008-Safety of machinery – Laser processing machines – Part 1: General safety requirements (ISO 11553-1:2005)

EN ISO 11553-2:2008-Safety of machinery – Laser processing machines – Part 2: Safety requirements for hand-held laser processing devices (ISO 11553-2:2007)

EN ISO 11554:2008-Optics and photonics – Lasers and laser-related equipment – Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2006)

EN ISO 11680-1:2011-Machinery for forestry – Safety requirements and testing for pole-mounted powered pruners – Part 1: Machines fitted with an integral combustion engine (ISO 11680-1:2011)

EN ISO 11680-2:2011-Machinery for forestry – Safety requirements and testing for pole-mounted powered pruners – Part 2: Machines for use with back-pack power source (ISO 11680-2:2011)

EN ISO 11681-1:2011-Machinery for forestry – Portable chain-saw safety requirements and testing – Part 1: Chain-saws for forest service (ISO 11681-1:2011)

EN ISO 11681-2:2011-Machinery for forestry – Portable chain-saw safety requirements and testing – Part 2: Chain-saws for tree service (ISO 11681-2:2011)

EN ISO 11688-1:2009-Acoustics – Recommended practice for the design of low-noise machinery and equipment – Part 1: Planning (ISO/TR 11688-1:1995)

EN ISO 11691:2009-Acoustics – Measurement of insertion loss of ducted silencers without flow – Laboratory survey method (ISO 11691:1995)

EN ISO 11806-1:2011-Agricultural and forestry machinery – Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers – Part 1: Machines fitted with an integral combustion engine (ISO 11806-1:2011)

EN ISO 11806-2:2011-Agricultural and forestry machinery – Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers – Part 2: Machines for use with back-pack power unit (ISO 11806-2:2011)

EN ISO 11850:2011-Machinery for forestry – General safety requirements (ISO 11850:2011)

EN ISO 11957:2009-Acoustics – Determination of sound insulation performance of cabins – Laboratory and in situ measurements (ISO 11957:1996)

EN ISO 12100:2010-Safety of machinery – General principles for design – Risk assessment and risk reduction (ISO 12100:2010)

EN ISO 13732-1:2008-Ergonomics of the thermal environment – Methods for the assessment of human responses to contact with surfaces – Part 1: Hot surfaces (ISO 13732-1:2006)

EN ISO 13732-3:2008-Ergonomics of the thermal environment – Methods for the assessment of human responses to contact with surfaces – Part 3: Cold surfaces (ISO 13732-3:2005)

EN ISO 13753:2008-Mechanical vibration and shock – Hand-arm vibration – Method for measuring the vibration transmissibility of resilient materials when loaded by the hand-arm system (ISO 13753:1998)

EN ISO 13849-1:2008-Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design (ISO 13849-1:2006)

EN ISO 13849-2:2008-Safety of machinery – Safety-related parts of control systems – Part 2: Validation (ISO 13849-2:2003)

EN ISO 13850:2008-Safety of machinery – Emergency stop – Principles for design (ISO 13850:2006)

EN ISO 13855:2010-Safety of machinery – Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010)

EN ISO 13857:2008-Safety of machinery – Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)

EN ISO 14122-1:2001-Safety of machinery – Permanent means of access to machinery – Part 1: Choice of fixed means of access between two levels (ISO 14122-1:2001)

EN ISO 14122-2:2001-Safety of machinery – Permanent means of access to machinery – Part 2: Working platforms and walkways (ISO 14122-2:2001)

EN ISO 14122-3:2001-Safety of machinery – Permanent means of access to machinery – Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001)

EN ISO 14122-4:2004-Safety of machinery – Permanent means of access to machinery – Part 4: Fixed ladders (ISO 14122-4:2004)

EN ISO 14159:2008-Safety of machinery – Hygiene requirements for the design of machinery (ISO 14159:2002)

EN ISO 14314:2009-Reciprocal internal combustion engines – Recoil starting equipment – General safety requirements (ISO 14314:2004)

EN ISO 14738:2008-Safety of machinery – Anthropometric requirements for the design of workstations at machinery (ISO 14738:2002, including Cor 1:2003 and Cor 2:2005)

EN ISO 14982:2009-Agricultural and forestry machinery – Electromagnetic compatibility – Test methods and acceptance criteria (ISO 14982:1998)

EN ISO 15536-1:2008-Ergonomics – Computer manikins and body templates – Part 1: General requirements (ISO 15536-1:2005)

EN ISO 15744:2008-Hand-held non-electric power tools – Noise measurement code – Engineering method (grade 2) (ISO 15744:2002)

EN ISO 19432:2008-Building construction machinery and equipment – Portable, hand-held, internal combustion engine driven cut-off machines – Safety requirements and testing (ISO 19432:2006)

EN ISO 20361:2009-Liquid pumps and pump units – Noise test code – Grades 2 and 3 of accuracy (ISO 20361:2007)

EN ISO 20643:2008-Mechanical vibration – Hand-held and hand-guided machinery – Principles for evaluation of vibration emission (ISO 20643:2005)

EN ISO 2151:2008-Acoustics – Noise test code for compressors and vacuum pumps – Engineering method (Grade 2) (ISO 2151:2004)

EN ISO 22867:2011-Forestry and gardening machinery – Vibration test code for portable hand-held machines with internal combustion engine – Vibration at the handles (ISO 22867:2011)

EN ISO 22868:2011-Forestry and gardening machinery – Noise test code for portable hand-held machines with internal combustion engine – Engineering method (Grade 2 accuracy) (ISO 22868:2011)

EN ISO 23125:2010-Machine tools – Safety – Turning machines (ISO 23125:2010)

EN ISO 28139:2009-Agricultural and forestry machinery – Knapsack combustion-engine-driven mistblowers – Safety requirements (ISO 28139:2009)

EN ISO 2860:2008-Earth-moving machinery – Minimum access dimensions (ISO 2860:1992)

EN ISO 2867:2011-Earth-moving machinery – Access systems (ISO 2867:2011)

EN ISO 28927-1:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 1: Angle and vertical grinders (ISO 28927-1:2009)

EN ISO 28927-10:2011-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 10: Percussive drills, hammers and breakers (ISO 28927-10:2011)

EN ISO 28927-11:2011-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 11: Stone hammers (ISO 28927-11:2011)

EN ISO 28927-2:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 2: Wrenches, nutrunners and screwdrivers (ISO 28927-2:2009)

EN ISO 28927-3:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 3: Polishers and rotary, orbital and random orbital sanders (ISO 28927-3:2009)

EN ISO 28927-4:2010-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 4: Straight grinders (ISO 28927-4:2010)

EN ISO 28927-5:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 5: Drills and impact drills (ISO 28927-5:2009)

EN ISO 28927-6:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 6: Rammers (ISO 28927-6:2009)

EN ISO 28927-7:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 7: Nibblers and shears (ISO 28927-7:2009)

EN ISO 28927-8:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 8: Saws, polishing and filing machines with reciprocating action and saws with oscillating or rotating action (ISO 28927-8:2009)

EN ISO 28927-9:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 9: Scaling hammers and needle scalers (ISO 28927-9:2009)

EN ISO 3164:2008-Earth-moving machinery – Laboratory evaluations of protective structures – Specifications for deflection-limiting volume (ISO 3164:1995)

EN ISO 3266:2010-Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010)

EN ISO 3411:2007-Earth-moving machinery – Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)

EN ISO 3449:2008-Earth-moving machinery – Falling-object protective structures – Laboratory tests and performance requirements (ISO 3449:2005)

EN ISO 3450:2011-Earth-moving machinery – Wheeled or high-speed rubber-tracked machines – Performance requirements and test procedures for brake systems (ISO 3450:2011)

EN ISO 3457:2008-Earth-moving machinery – Guards – Definitions and requirements (ISO 3457:2003)

EN ISO 3471:2008-Earth-moving machinery – Roll-over protective structures – Laboratory tests and performance requirements (ISO 3471:2008)

EN ISO 3741:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for reverberation test rooms (ISO 3741:2010)

EN ISO 3743-1:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for small movable sources in reverberant fields – Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)

EN ISO 3743-2:2009-Acoustics – Determination of sound power levels of noise sources using sound pressure – Engineering methods for small, movable sources in reverberant fields – Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)

EN ISO 3744:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)

EN ISO 3745:2012 (new)-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for anechoic rooms and hemi-anechoic rooms (ISO 3745:2012)

EN ISO 3746:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)

EN ISO 3747:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010)

EN ISO 4254-1:2009-Agricultural machinery – Safety – Part 1: General requirements (ISO 4254-1:2008)

EN ISO 4254-10:2009-Agricultural machinery – Safety – Part 10: Rotary tedders and rakes (ISO 4254-10:2009)

EN ISO 4254-11:2010-Agricultural machinery – Safety – Part 11: Pick-up balers (ISO 4254-11:2010)

EN ISO 4254-5:2009-Agricultural machinery – Safety – Part 5: Power-driven soil-working machines (ISO 4254-5:2008)

EN ISO 4254-6:2009-Agricultural machinery – Safety – Part 6: Sprayers and liquid fertilizer distributors (ISO 4254-6:2009)

EN ISO 4254-7:2009-Agricultural machinery – Safety – Part 7: Combine harvesters, forage harvesters and cotton harvesters (ISO 4254-7:2008)

EN ISO 4413:2010-Hydraulic fluid power – General rules and safety requirements for systems and their components (ISO 4413:2010)

EN ISO 4414:2010-Pneumatic fluid power – General rules and safety requirements for systems and their components (ISO 4414:2010)

EN ISO 4871:2009-Acoustics – Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)

EN ISO 5136:2009-Acoustics – Determination of sound power radiated into a duct by fans and other air-moving devices – In-duct method (ISO 5136:2003)

EN ISO 5674:2009-Tractors and machinery for agriculture and forestry – Guards for power take-off (PTO) drive-shafts – Strength and wear tests and acceptance criteria (ISO 5674:2004, corrected version 2005-07-01)

EN ISO 6682:2008-Earth-moving machinery – Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989)

EN ISO 6683:2008-Earth-moving machinery – Seat belts and seat belt anchorages – Performance requirements and tests (ISO 6683:2005)

EN ISO 7096:2008-Earth-moving machinery – Laboratory evaluation of operator seat vibration (ISO 7096:2000)

EN ISO 7235:2009-Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss (ISO 7235:2003)

EN ISO 7731:2008-Ergonomics – Danger signals for public and work areas – Auditory danger signals (ISO 7731:2003)

EN ISO 8230-1:2008-Safety requirements for dry-cleaning machines – Part 1: Common safety requirements (ISO 8230-1:2008)

EN ISO 8230-2:2008-Safety requirements for dry-cleaning machines – Part 2: Machines using perchloroethylene (ISO 8230-2:2008)

EN ISO 8230-3:2008-Safety requirements for dry-cleaning machines – Part 3: Machines using combustible solvents (ISO 8230-3:2008)

EN ISO 9614-1:2009-Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 1: Measurement at discrete points (ISO 9614-1:1993)

EN ISO 9614-3:2009-Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)

EN ISO 9902-1:2001-Textile machinery – Noise test code – Part 1: Common requirements (ISO 9902-1:2001)

EN ISO 9902-2:2001-Textile machinery – Noise test code – Part 2: Spinning preparatory and spinning machinery (ISO 9902-2:2001)

EN ISO 9902-3:2001-Textile machinery – Noise test code – Part 3: Nonwoven machinery (ISO 9902-3:2001)

EN ISO 9902-4:2001-Textile machinery – Noise test code – Part 4: Yarn processing, cordage and rope manufacturing machinery (ISO 9902-4:2001)

EN ISO 9902-5:2001-Textile machinery – Noise test code – Part 5: Weaving and knitting preparatory machinery (ISO 9902-5:2001)

EN ISO 9902-6:2001-Textile machinery – Noise test code – Part 6: Fabric manufacturing machinery (ISO 9902-6:2001)

EN ISO 9902-7:2001-Textile machinery – Noise test code – Part 7: Dyeing and finishing machinery (ISO 9902-7:2001)

CE Marking – Machinery Direcitve Annex IV

23 Dec 2013 Comments
Off

이들 기계류는 고 위험군기계류로써 유럽위원회로부터 권한을 부여 받은 Notified  Body(NB)에 의해 해당되는 제품별 규격에 따라  ” EU형식시험”, 등 기계류지침 절차에 따라 인증되고 지속적 적합성을 관리 합니다.

일반적으로 원형 톱 기계, 밴드 톱 기계, 사출, 압출용 플라스틱 가공 기계, 자동차용 lift기계 및 기타 안전 기능  품목과 전도, 낙하물 보호장치가 필요한 기계류 등으로써 인체에게 심각한 손상을 가할 수 있는 기계류 입니다.

 

1. Circular saws (single- or multi-blade) for working with wood and material with similar physical characteristics or for working with meat and material with similar physical characteristics, of the following types:

1.1. sawing machinery with fixed blade(s) during cutting, having a fixed bed or support with manual feed of the workpiece or with a demountable power feed;

1.2. sawing machinery with fixed blade(s) during cutting, having a manually operated reciprocating saw-bench or carriage;

1.3 sawing machinery with fixed blade(s) during cutting, having a built-in mechanical feed device for the workpieces, with manual loading and/or unloading;

1.4. sawing machinery with movable blade(s) during cutting, having mechanical movement of the blade, with manual loading and/or unloading.

2. Hand-fed surface planing machinery for woodworking.

3. Thicknessers for one-side dressing having a built-in mechanical feed device, with manual loading and/or unloading for woodworking.

4. Band-saws with manual loading and/or unloading for working with wood and material  with similar physical characteristics or for working with meat and  material with similar physical characteristics, of the following types:

4.1. sawing machinery with fixed blade(s) during cutting, having a fixed or reciprocating-movement  bed or support for the workpiece;

4.2. sawing machinery with blade(s) assembled on a carriage with reciprocating motion.

5. Combined machinery of the types referred to in points 1 to 4 and in point 7 for  working with wood and material with similar physical characteristics.

6. Hand-fed tenoning machinery with several tool holders for woodworking.

7. Hand-fed vertical spindle moulding machinery for working with wood and material with similar physical characteristics.

8. Portable chainsaws for woodworking.

9. Presses, including press-brakes, for the cold working of metals, with manual loading and/or unloading, whose movable working parts may have a travel exceeding 6 mm and a speed exceeding 30 mm/s.

10. Injection or compression plastics-moulding machinery with manual loading or unloading.

11. Injection or compression rubber-moulding machinery with manual loading or unloading.

12. Machinery for underground working of the following types:

12.1. locomotives and brake-vans;

12.2. hydraulic-powered roof supports.

13. Manually loaded trucks for the collection of household refuse incorporating a compression mechanism.

14. Removable mechanical transmission devices including their guards.

15. Guards for removable mechanical transmission devices.

16. Vehicle servicing lifts.

17. Devices for the lifting of persons or of persons and goods involving a hazard of falling from a vertical height of more than three metres.

18. Portable cartridge-operated fixing and other impact machinery.

19. Protective devices designed to detect the presence of persons.

20. Power-operated interlocking movable guards designed to be used as safeguards in machinery referred to in points 9, 10 and 11.

21. Logic units to ensure safety functions.

22. Roll-over protective structures (ROPS).

23. Falling-object protective structures (FOPS

건설자재 CE Mark관련 EN 규격

23 Dec 2013 Comments
Off

건설자재 CE Mark관련 EN 규격

EN 1:1998-Flued oil stoves with vaporizing burners

EN 10025-1:2004Hot rolled products of structural steels – Part 1: General technical delivery conditions

EN 10088-4:2009Stainless steels – Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes

EN 10088-5:2009Stainless steels – Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes

EN 1020:2009Non-domestic forced convection gas-fired air heaters for space heating not exceeding a net heat input of 300 kW incorporating a fan to assist transportation of combustion air or combustion products

EN 10210-1:2006Hot finished structural hollow sections of non-alloy and fine grain steels – Part 1: Technical delivery conditions

EN 10219-1:2006Cold formed welded structural hollow sections of non-alloy and fine grain steels – Part 1: Technical delivery conditions

EN 10224:2002Non-alloy steel tubes and fittings for the conveyance of aqueous liquids including water for human consumption – Technical delivery conditions

EN 10255:2004+A1:2007Non-Alloy steel tubes suitable for welding and threading – Technical delivery conditions

EN 10311:2005Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids

EN 10312:2002Welded stainless steel tubes for the conveyance of aqueous liquids including water for human consumption – Technical delivery conditions

EN 10340:2007Steel castings for structural uses

EN 10343:2009Steels for quenching and tempering for construction purposes – Technical delivery conditions

EN 1036-2:2008Glass in building – Mirrors from silver-coated float glass for internal use – Part 2: Evaluation of conformity; product standard

EN 1051-2:2007Glass in building – Glass blocks and glass pavers – Part 2: Evaluation of conformity/Product standard

EN 1057:2006+A1:2010Copper and copper alloys – Seamless, round copper tubes for water and gas in sanitary and heating applications

EN 1090-1:2009+A1:2011 (new)Execution of steel structures and aluminium structures – Part 1: Requirements for conformity assessment of structural components

EN 1096-4:2004Glass in building – Coated glass – Part 4: Evaluation of conformity/Product standard

EN 1123-1:1999Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control

EN 1124-1:1999Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control

EN 1125:2008Building hardware – Panic exit devices operated by a horizontal bar, for use on escape routes – Requirements and test methods

EN 1154:1996Building hardware – Controlled door closing devices – Requirements and test methods

EN 1155:1997Building hardware – Electrically powered hold-open devices for swing doors – Requirements and test methods

EN 1158:1997Building hardware – Door coordinator devices – Requirements and test methods

EN 1168:2005+A3:2011 (new)Precast concrete products – Hollow core slabs

EN 12004:2007Adhesives for tiles – Requirements, evaluation of conformity, classification and designation

EN 12050-1:2001Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 1: Lifting plants for wastewater containing faecal matter

EN 12050-2:2000Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 2: Lifting plants for faecal-free wastewater

EN 12050-3:2000Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 3: Lifting plants for wastewater containing faecal matter for limited applications

EN 12050-4:2000Wastewater lifting plants for buildings and sites – Principles of construction and testing – Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter

EN 12057:2004Natural stone products – Modular tiles – Requirements

EN 12058:2004Natural stone products – Slabs for floors and stairs – Requirements

EN 12094-1:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 1: Requirements and test methods for electrical automatic control and delay devices

EN 12094-10:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 10: Requirements and test methods for pressure gauges and pressure switches

EN 12094-11:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 11: Requirements and test methods for mechanical weighing devices

EN 12094-12:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 12: Requirements and test methods for pneumatic alarm devices

EN 12094-13:2001Fixed firefighting systems – Components for gas extinguishing systems – Part 13: Requirements and test methods for check valves and non-return valves

EN 12094-2:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 2: Requirements and test methods for non-electrical automatic control and delay devices

EN 12094-3:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 3: Requirements and test methods for manual triggering and stop devices

EN 12094-4:2004Fixed firefighting systems – Components for gas extinguishing systems – Part 4: Requirements and test methods for container valve assemblies and their actuators

EN 12094-5:2006Fixed firefighting systems – Components for gas extinguishing systems – Part 5: Requirements and test methods for high and low pressure selector valves and their actuators

EN 12094-6:2006Fixed firefighting systems – Components for gas extinguishing systems – Part 6: Requirements and test methods for non-electrical disable devices

EN 12094-7:2000Fixed firefighting systems – Components for gas extinguishing systems – Part 7: Requirements and test methods for nozzles for CO2 systems

EN 12094-8:2006Fixed firefighting systems – Components for gas extinguishing systems – Part 8: Requirements and test methods for connectors

EN 12094-9:2003Fixed firefighting systems – Components for gas extinguishing systems – Part 9: Requirements and test methods for special fire detectors

EN 12101-1:2005Smoke and heat control systems – Part 1: Specification for smoke barriers

EN 12101-10:2005Smoke and heat control systems – Part 10: Power supplies

EN 12101-2:2003Smoke and heat control systems – Part 2: Specification for natural smoke and heat exhaust ventilators

EN 12101-3:2002Smoke and heat control systems – Part 3: Specification for powered smoke and heat exhaust ventilators

EN 12101-6:2005Smoke and heat control systems – Part 6: Specification for pressure differential systems – Kits

EN 12101-7:2011Smoke and heat control systems – Part 7: Smoke duct sections

EN 12101-8:2011Smoke and heat control systems – Part 8: Smoke control dampers

EN 12150-2:2004Glass in building – Thermally toughened soda lime silicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 12209:2003Building hardware – Locks and latches – Mechanically operated locks, latches and locking plates – Requirements and test methods

EN 12259-1:1999 + A1:2001Fixed firefighting systems – Components for sprinkler and water spray systems – Part 1: Sprinklers

EN 12259-2:1999Fixed firefighting systems – Components for sprinkler and water spray systems – Part 2: Wet alarm valve assemblies

EN 12259-3:2000Fixed firefighting systems – Components for automatic sprinkler and water spray systems – Part 3: Dry alarm valve assemblies

EN 12259-4:2000Fixed firefighting systems – Components for sprinkler and water spray systems – Part 4: Water motor alarms

EN 12259-5:2002Fixed firefighting systems – Components for sprinkler and water spray systems – Part 5: Water flow detectors

EN 12271:2006Surface dressing – Requirements

EN 12273:2008Slurry surfacing – Requirements

EN 12285-2:2005Workshop fabricated steel tanks – Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids

EN 12326-1:2004Slate and stone products for discontinuous roofing and cladding – Part 1: Product specification

EN 12337-2:2004Glass in building – Chemically strengthened soda lime silicate glass – Part 2: Evaluation of conformity/Product standard

EN 12352:2006Traffic control equipment – Warning and safety light devices

EN 12368:2006Traffic control equipment – Signal heads

EN 12380:2002Air admittance valves for drainage systems – Requirements, tests methods and evaluation of conformity

EN 12446:2011Chimneys – Components – Concrete outer wall elements

EN 12467:2004Fibre-cement flat sheets – Product specification and test methods

EN 12566-1:2000Small wastewater treatment systems for up to 50 PT – Part 1: Prefabricated septic tanks

EN 12566-3:2005+A1:2009Small wastewater treatment systems for up to 50 PT – Part 3: Packaged and/or site assembled domestic wastewater treatment plants

EN 12566-4:2007Small wastewater treatment systems for up to 50 PT – Part 4: Septic tanks assembled in situ from prefabricated kits

EN 12591:2009Bitumen and bituminous binders – Specifications for paving grade bitumens

EN 12620:2002+A1:2008Aggregates for concrete

EN 12676-1:2000Anti-glare systems for roads – Part 1: Performance and characteristics

EN 12737:2004+A1:2007Precast concrete products – Floor slats for livestock

EN 12764:2004+A1:2008Sanitary appliances – Specification for whirlpool baths

EN 12794:2005+A1:2007Precast concrete products – Foundation piles

EN 1279-5:2005+A2:2010Glass in building – Insulating glass units – Part 5: Evaluation of conformity

EN 12809:2001Residential independent boilers fired by solid fuel – Nominal heat output up to 50 kW – Requirements and test methods

EN 12815:2001Residential cookers fired by solid fuel – Requirements and test methods

EN 12839:2012 (new)Precast concrete products – Elements for fences

EN 12843:2004Precast concrete products – Masts and poles

EN 12859:2011Gypsum blocks – Definitions, requirements and test methods

EN 12860:2001Gypsum based adhesives for gypsum blocks – Definitions, requirements and test methods

EN 12878:2005Pigments for the colouring of building materials based on cement and/or lime – Specifications and methods of test

EN 12899-1:2007Fixed, vertical road traffic signs – Part 1: Fixed signs

EN 12899-2:2007Fixed, vertical road traffic signs – Part 2: Transilluminated traffic bollards (TTB)

EN 12899-3:2007Fixed, vertical road traffic signs – Part 3: Delineator posts and retroreflectors

EN 12951:2004Prefabricated accessories for roofing – Permanently fixed roof ladders – Product specification and test methods

EN 12966-1:2005+A1:2009Road vertical signs – Variable message traffic signs – Part 1: Product standard

EN 13024-2:2004Glass in building – Thermally toughened borosilicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 1304:2005Clay roofing tiles and fittings – Product definitions and specifications

EN 13043:2002Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas

EN 13055-1:2002Lightweight aggregates – Part 1: Lightweight aggregates for concrete, mortar and grout

EN 13055-2:2004Lightweight aggregates – Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications

EN 13063-1:2005+A1:2007Chimneys – System chimneys with clay/ceramic flue liners – Part 1: Requirements and test methods for sootfire resistance

EN 13063-2:2005+A1:2007Chimneys – System chimneys with clay/ceramic flue liners – Part 2: Requirements and test methods under wet conditions

EN 13063-3:2007Chimneys – System chimneys with clay/ceramic flue liners – Part 3: Requirements and test methods for air flue system chimneys

EN 13069:2005Chimneys – Clay/ceramic outer walls for system chimneys – Requirements and test methods

EN 13084-5:2005Free-standing chimneys – Part 5: Material for brick liners – Product specifications

EN 13084-7:2005Free-standing chimneys – Part 7: Product specifications of cylindrical steel fabrications for use in single wall steel chimneys and steel liners

EN 13101:2002Steps for underground man entry chambers – Requirements, marking, testing and evaluation of conformity

EN 13108-1:2006Bituminous mixtures – Material specifications – Part 1: Asphalt Concrete

EN 13108-2:2006Bituminous mixtures – Material specifications – Part 2: Asphalt Concrete for very thin layers

EN 13108-3:2006Bituminous mixtures – Material specifications – Part 3: Soft Asphalt

EN 13108-4:2006Bituminous mixtures – Material specifications – Part 4: Hot Rolled Asphalt

EN 13108-5:2006Bituminous mixtures – Material specifications – Part 5: Stone Mastic Asphalt

EN 13108-6:2006Bituminous mixtures – Material specifications – Part 6: Mastic Asphalt

EN 13108-7:2006Bituminous mixtures – Material specifications – Part 7: Porous Asphalt

EN 13139:2002Aggregates for mortar

EN 13160-1:2003Leak detection systems – Part 1: General principles

EN 13162:2008Thermal insulation products for buildings – Factory made mineral wool (MW) products – Specification

EN 13163:2008Thermal insulation products for buildings – Factory made products of expanded polystyrene (EPS) – Specification

EN 13164:2008Thermal insulation products for buildings – Factory made products of extruded polystyrene foam (XPS) – Specification

EN 13165:2008Thermal insulation products for buildings – Factory made rigid polyurethane foam (PUR) products – Specification

EN 13166:2008Thermal insulation products for buildings – Factory made products of phenolic foam (PF) – Specification

EN 13167:2008Thermal insulation products for buildings – Factory made cellular glass (CG) products – Specification

EN 13168:2008Thermal insulation products for buildings – Factory made wood wool (WW) products – Specification

EN 13169:2008Thermal insulation products for buildings – Factory made products of expanded perlite (EPB) – Specification

EN 13170:2008Thermal insulation products for buildings – Factory made products of expanded cork (ICB) – Specification

EN 13171:2008Thermal insulating products for buildings – Factory made wood fibre (WF) products – Specification

EN 1317-5:2007+A2:2012 (new)Road restraint systems – Part 5: Product requirements and evaluation of conformity for vehicle restraint systems

EN 1319:2009Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW

EN 13224:2011 (new)Precast concrete products – Ribbed floor elements

EN 13225:2004Precast concrete products – Linear structural elements

EN 13229:2001Inset appliances including open fires fired by solid fuels – Requirements and test methods

EN 13240:2001Roomheaters fired by solid fuel – Requirements and test methods

EN 13241-1:2003+A1:2011Industrial, commercial and garage doors and gates – Product standard – Part 1: Products without fire resistance or smoke control characteristics

EN 13242:2002+A1:2007Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction

EN 13245-2:2008Plastics – Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications – Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes

EN 13249:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of roads and other trafficked areas (excluding railways and asphalt inclusion)

EN 13250:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of railways

EN 13251:2000Geotextiles and geotextile-related products – Characteristics required for use in earthworks, foundations and retaining structures

EN 13252:2000Geotextiles and geotextile-related products – Characteristics required for use in drainage systems

EN 13253:2000Geotextiles and geotextile-related products – Characteristics required for use in erosion control works (coastal protection, bank revetments)

EN 13254:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of reservoirs and dams

EN 13255:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of canals

EN 13256:2000Geotextiles and geotextile-related products – Characteristics required for use in the construction of tunnels and underground structures

EN 13257:2000Geotextiles and geotextile-related products – Characteristics required for use in solid waste disposals

EN 13263-1:2005+A1:2009Silica fume for concrete – Part 1: Definitions, requirements and conformity criteria

EN 13265:2000Geotextiles and geotextile-related products – Characteristics required for use in liquid waste containment projects

EN 13279-1:2008Gypsum binders and gypsum plasters – Part 1: Definitions and requirements

EN 13310:2003Kitchen sinks – Functional requirements and test methods

EN 13341:2005+A1:2011Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels – Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of nionically polymerized polyamide 6 – Requirements and test methods

EN 13361:2004Geosynthetic barriers – Characteristics required for use in the construction of reservoirs and dams

EN 13362:2005Geosynthetic Barriers – Characteristics required for use in the construction of canals

EN 1337-3:2005Structural bearings – Part 3: Elastomeric bearings

EN 1337-4:2004Structural bearings – Part 4: Roller bearings

EN 1337-5:2005Structural bearings – Part 5: Pot bearings

EN 1337-6:2004Structural bearings – Part 6: Rocker bearings

EN 1337-7:2004Structural bearings – Part 7: Spherical and cylindrical PTFE bearings

EN 1337-8:2007Structural bearings – Part 8: Guide Bearings and Restraint Bearings

EN 1338:2003Concrete paving blocks – Requirements and test methods

EN 13383-1:2002Armourstone – Part 1: Specification

EN 1339:2003Concrete paving flags – Requirements and test methods

EN 1340:2003Concrete kerb units – Requirements and test methods

EN 13407:2006Wall-hung urinals – Functional requirements and test methods

EN 1341:2001Slabs of natural stone for external paving – Requirements and test methods

EN 1342:2001Setts of natural stone for external paving – Requirements and test methods

EN 1343:2001Kerbs of natural stone for external paving – Requirements and test methods

EN 1344:2002Clay pavers – Requirements and test methods EN 13450:2002Aggregates for railway ballast

EN 13454-1:2004Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate – Part 1: Definitions and requirements

EN 13479:2004Welding consumables – General product standard for filler metals and fluxes for fusion welding of metallic materials

EN 13491:2004Geosynthetic barriers – Characteristics required for use as a fluid barrier in the construction of tunnels and underground structures

EN 13492:2004Geosynthetic barriers – Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment

EN 13493:2005Geosynthetic barriers – Characteristics required for use in the construction of solid waste storage and disposal sites

EN 13502:2002Chimneys – Requirements and test methods for clay/ceramic flue terminals

EN 13561:2004+A1:2008External blinds – Performance requirements including safety

EN 13564-1:2002Anti-flooding devices for buildings – Part 1: Requirements

EN 13616:2004Overfill prevention devices for static tanks for liquid petroleum fuels

EN 13658-1:2005Metal lath and beads – Definitions, requirements and test methods – Part 1: Internal plastering

EN 13658-2:2005Metal lath and beads – Definitions, requirements and test methods – Part 2: External rendering

EN 13659:2004+A1:2008Shutters – Performance requirements including safety

EN 13693:2004+A1:2009Precast concrete products – Special roof elements

EN 13707:2004+A2:2009Flexible sheets for waterproofing – Reinforced bitumen sheets for roof waterproofing – Definitions and characteristics

EN 13747:2005+A2:2010Precast concrete products – Floor plates for floor systems

EN 13748-1:2004Terrazzo tiles – Part 1: Terrazzo tiles for internal use

EN 13748-2:2004Terrazzo tiles – Part 2: Terrazzo tiles for external use

EN 13808:2005Bitumen and bituminous binders – Framework for specifying cationic bituminous emulsions

EN 13813:2002Screed material and floor screeds – Screed material – Properties and requirements

EN 13815:2006Fibrous gypsum plaster casts – Definitions, requirements and test methods

EN 13830:2003Curtain walling – Product standard

EN 13859-1:2010Flexible sheets for waterproofing – Definitions and characteristics of underlays – Part 1: Underlays for discontinuous roofing

EN 13859-2:2010Flexible sheets for waterproofing – Definitions and characteristics of underlays – Part 2: Underlays for walls

EN 13877-3:2004Concrete pavements – Part 3: Specifications for dowels to be used in concrete pavements

EN 13915:2007Prefabricated gypsum plasterboard panels with a cellular paperboard core – Definitions, requirements and test methods

EN 13924:2006Bitumen and bituminous binders – Specifications for hard paving grade bitumens

EN 13950:2005Gypsum plasterboard thermal/acoustic insulation composite panels – Definitions, requirements and test methods

EN 13956:2005Flexible sheet for waterproofing – Plastic and rubber sheets for roof waterproofing – Definitions and characteristics

EN 13963:2005Jointing materials for gypsum plasterboards – Definitions, requirements and test methods

EN 13964:2004Suspended ceilings – Requirements and test methods

EN 13967:2004Flexible sheets for waterproofing – Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet – Definitions and characteristics

EN 13969:2004Flexible sheets for waterproofing – Bitumen damp proof sheets including bitumen basement tanking sheets – Definitions and characteristics

EN 13970:2004Flexible sheets for waterproofing – Bitumen water vapour control layers – Definitions and characteristics

EN 13978-1:2005Precast concrete products – Precast concrete garages – Part 1: Requirements for reinforced garages monolithic or consisting of single sections with room dimensions

EN 13984:2004Flexible sheets for waterproofing – Plastic and rubber vapour control layers – Definitions and characteristics

EN 13986:2004Wood-based panels for use in construction – Characteristics, evaluation of conformity and marking

EN 14016-1:2004Binders for magnesite screeds – Caustic magnesia and magnesium chloride – Part 1: Definitions, requirements

EN 14023:2010Bitumen and bituminous binders – Specification framework for polymer modified bitumens

EN 14037-1:2003Ceiling mounted radiant panels supplied with water at temperature below 120 °C – Part 1: Technical specifications and requirements

EN 14041:2004Resilient, textile and laminate floor coverings – Essential characteristics

EN 14055:2010WC and urinal flushing cisterns

EN 14063-1:2004Thermal insulation products for buildings – In-situ formed expanded clay lightweight aggregate products – Part 1: Specification for the loose-fill products before installation

EN 14064-1:2010Thermal insulation products for buildings – In-situ formed loose-fill mineral wool (MW) products – Part 1: Specification for the loose-fill products before installation

EN 14080:2005Timber structures – Glued laminated timber – Requirements

EN 14081-1:2005+A1:2011Timber structures – Strength graded structural timber with rectangular cross section – Part 1: General requirements

EN 14178-2:2004Glass in building – Basic alkaline earth silicate glass products – Part 2: Evaluation of conformity/Product standard

EN 14179-2:2005Glass in building – Heat soaked thermally toughened soda lime silicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 14188-1:2004Joint fillers and sealants – Part 1: Specifications for hot applied sealants

EN 14188-2:2004Joint fillers and sealants – Part 2: Specifications for cold applied sealants

EN 14188-3:2006Joint fillers and sealants – Part 3: Specifications for preformed joint seals

EN 14190:2005Gypsum plasterboard products from reprocessing – Definitions, requirements and test methods

EN 14195:2005Metal framing components for gypsum plasterboard systems – Definitions, requirements and test methods

EN 14209:2005Preformed plasterboard cornices – Definitions, requirements and test methods

EN 14216:2004Cement – Composition, specifications and conformity criteria for very low heat special cements

EN 14229:2010Structural timber – Wood poles for overhead lines

EN 1423:2012 (new)Road marking materials – Drop on materials – Glass beads, antiskid aggregates and mixtures of the two

EN 14246:2006Gypsum elements for suspended ceilings – Definitions, requirements and test methods

EN 14250:2010Timber structures – Product requirements for prefabricated structural members assembled with punched metal plate fasteners

EN 14296:2005Sanitary appliances – Communal washing troughs

EN 14303:2009Thermal insulation products for building equipment and industrial installations – Factory made mineral wool (MW) products – Specification

EN 14304:2009Thermal insulation products for building equipment and industrial installations – Factory made flexible elastomeric foam (FEF) products – Specification

EN 14305:2009Thermal insulation products for building equipment and industrial installations – Factory made cellular glass (CG) products – Specification

EN 14306:2009Thermal insulation products for building equipment and industrial installations – Factory made calcium silicate (CS) products – Specification

EN 14307:2009Thermal insulation products for building equipment and industrial installations – Factory made extruded polystyrene foam (XPS) products – Specification

EN 14308:2009Thermal insulation products for building equipment and industrial installations – Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products – Specification

EN 14309:2009Thermal insulation products for building equipment and industrial installations – Factory made products of expanded polystyrene (EPS) – Specification

EN 14313:2009Thermal insulation products for building equipment and industrial installations – Factory made polyethylene foam (PEF) products – Specification

EN 14314:2009Thermal insulation products for building equipment and industrial installations – Factory made phenolic foam (PF) products – Specification

EN 14316-1:2004Thermal insulation products for buildings – In-situ thermal insulation formed from expanded perlite (EP) products – Part 1: Specification for bonded and loose-fill products before installation

EN 14317-1:2004Thermal insulation products for buildings – In-situ thermal insulation formed from exfoliated vermiculite (EV) products – Part 1: Specification for bonded and loose-fill products before installation

EN 14321-2:2005Glass in building – Thermally toughened alkaline earth silicate safety glass – Part 2: Evaluation of conformity/Product standard

EN 1433:2002Drainage channels for vehicular and pedestrian areas – Classification, design and testing requirements, marking and evaluation of conformity

EN 14339:2005Underground fire hydrants

EN 14342:2005+A1:2008Wood flooring – Characteristics, evaluation of conformity and marking

EN 14351-1:2006+A1:2010Windows and doors – Product standard, performance characteristics – Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics

EN 14353:2007+A1:2010Metal beads and feature profiles for use with gypsum plasterboards – Definitions, requirements and test methods

EN 14374:2004Timber structures – Structural laminated veneer lumber – Requirements

EN 14384:2005Pillar fire hydrants

EN 14388:2005Road traffic noise reducing devices – Specifications

EN 14396:2004Fixed ladders for manholes

EN 14399-1:2005High-strength structural bolting assemblies for preloading – Part 1: General requirements

EN 14411:2006Ceramic tiles – Definitions, classification, characteristics and marking

EN 14428:2004+A1:2008Shower enclosures – Functional requirements and test methods

EN 14449:2005Glass in building – Laminated glass and laminated safety glass – Evaluation of conformity/Product standard

EN 14471:2005Chimneys – System chimneys with plastic flue liners – Requirements and test methods

EN 14496:2005Gypsum based adhesives for thermal/acoustic insulation composite panels and plasterboards – Definitions, requirements and test methods

EN 14509:2006Self-supporting double skin metal faced insulating panels – Factory made products – Specifications

EN 14516:2006+A1:2010Baths for domestic purposes

EN 14527:2006+A1:2010Shower trays for domestic purposes

EN 14528:2007Bidets – Functional requirements and test methods

EN 14545:2008Timber structures – Connectors – Requirements

EN 14566:2008+A1:2009Mechanical fasteners for gypsum plasterboard systems – Definitions, requirements and test methods

EN 1457-1:2012 (new)Chimneys – Clay/ceramic flue liners – Part 1: Flue liners operating under dry conditions – Requirements and test methods

EN 1457-2:2012 (new)Chimneys – Clay/ceramic flue liners – Part 2: Flue liners operating under wet conditions – Requirements and test methods

EN 14592:2008Timber structures – Dowel-type fasteners – Requirements

EN 14604:2005Smoke alarm devices

EN 1463-1:2009Road marking materials – Retroreflecting road studs – Part 1: Initial performance requirements

EN 14647:2005Calcium aluminate cement – Composition, specifications and conformity criteria

EN 14680:2006Adhesives for non-pressure thermoplastic piping systems – Specifications

EN 14688:2006Sanitary appliances – Wash basins – Functional requirements and test methods

EN 1469:2004Natural stone products – Slabs for cladding – Requirements

EN 14695:2010Flexible sheets for waterproofing – Reinforced bitumen sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete – Definitions and characteristics

EN 14716:2004Stretched ceilings – Requirements and test methods

EN 14782:2006Self-supporting metal sheet for roofing, external cladding and internal lining – Product specification and requirements

EN 14783:2006Fully supported metal sheet and strip for roofing, external cladding and internal lining – Product specification and requirements

EN 14785:2006Residential space heating appliances fired by wood pellets – Requirements and test methods

EN 14800:2007Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels

EN 14814:2007Adhesives for thermoplastic piping systems for fluids under pressure – Specifications

EN 14843:2007Precast concrete products – Stairs

EN 14844:2006+A2:2011 (new)Precast concrete products – Box culverts

EN 14846:2008Building hardware – Locks and latches – Electromechanically operated locks and striking plates – Requirements and test methods

EN 14889-1:2006Fibres for concrete – Part 1: Steel fibres – Definitions, specifications and conformity

EN 14889-2:2006Fibres for concrete – Part 2: Polymer fibres – Definitions, specifications and conformity

EN 14904:2006Surfaces for sports areas – Indoor surfaces for multi-sports use – Specification

EN 14909:2006Flexible sheets for waterproofing – Plastic and rubber damp proof courses – Definitions and characteristics

EN 14915:2006Solid wood panelling and cladding – Characteristics, evaluation of conformity and marking

EN 14933:2007Thermal insulation and light weight fill products for civil engineering applications – Factory made products of expanded polystyrene (EPS) – Specification

EN 14934:2007Thermal insulation and light weight fill products for civil engineering applications – Factory made products of extruded polystyrene foam (XPS) – Specification

EN 14963:2006Roof coverings – Continuous rooflights of plastics with or without upstands – Classification, requirements and test methods

EN 14964:2006Rigid underlays for discontinuous roofing – Definitions and characteristics

EN 14967:2006Flexible sheets for waterproofing – Bitumen damp proof courses – Definitions and characteristics

EN 14989-1:2007Chimneys – Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications – Part 1: Vertical air/flue terminals for C6-type appliances

EN 14989-2:2007Chimneys – Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications – Part 2: Flue and air supply ducts for room sealed appliances

EN 14991:2007Precast concrete products – Foundation elements

EN 14992:2007Precast concrete products – Wall elements

EN 15037-1:2008Precast concrete products – Beam-and-block floor systems – Part 1: Beams

EN 15037-2:2009+A1:2011Precast concrete products – Beam-and-block floor systems – Part 2: Concrete blocks

EN 15037-3:2009+A1:2011Precast concrete products – Beam-and-block floor systems – Part 3: Clay blocks

EN 15037-4:2010Precast concrete products – Beam-and-block floor systems – Part 4: Expanded polystyrene blocks

EN 1504-2:2004Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 2: Surface protection systems for concrete

EN 1504-3:2005Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 3: Structural and non-structural repair

EN 1504-4:2004Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 4: Structural bonding

EN 1504-5:2004Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 5: Concrete injection

EN 1504-6:2006Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 6: Anchoring of reinforcing steel bar

EN 1504-7:2006Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and evaluation of conformity – Part 7: Reinforcement corrosion protection

EN 15048-1:2007Non-preloaded structural bolting assemblies – Part 1: General requirements

EN 15050:2007+A1:2012 (new)Precast concrete products – Bridge elements

EN 15069:2008Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel

EN 15088:2005Aluminium and aluminium alloys – Structural products for construction works – Technical conditions for inspection and delivery

EN 15102:2007+A1:2011 (new)Decorative wall coverings – Roll and panel form

EN 15129:2009Anti-seismic devices

EN 15167-1:2006Ground granulated blast furnace slag for use in concrete, mortar and grout – Part 1: Definitions, specifications and conformity criteria

EN 1520:2011Prefabricated reinforced components of lightweight aggregate concrete with open structure with structural or non-structural reinforcement

EN 15250:2007Slow heat release appliances fired by solid fuel – Requirements and test methods

EN 15258:2008-Precast concrete products – Retaining wall elements

EN 15274:2007General purpose adhesives for structural assembly – Requirements and test methods

EN 15275:2007Structural adhesives – Characterisation of anaerobic adhesives for co-axial metallic assembly in building and civil engineering structures

EN 15283-1:2008+A1:2009Gypsum boards with fibrous reinforcement – Definitions, requirements and test methods – Part 1: Gypsum boards with mat reinforcement

EN 15283-2:2008+A1:2009Gypsum boards with fibrous reinforcement – Definitions, requirements and test methods – Part 2: Gypsum fibre boards

EN 15285:2008Agglomerated stone – Modular tiles for flooring and stairs (internal and external)

EN 15322:2009Bitumen and bituminous binders – Framework for specifying cut-back and fluxed bituminous binders

EN 15368:2008+A1:2010Hydraulic binder for non-structural applications – Definition, specifications and conformity criteria

EN 15381:2008Geotextiles and geotextile-related products – Characteristics required for use in pavements and asphalt overlays

EN 15382:2008Geosynthetic barriers – Characteristics required for use in transportation infrastructure

EN 15435:2008Precast concrete products – Normal weight and lightweight concrete shuttering blocks – Product properties and performance

EN 15498:2008Precast concrete products – Wood-chip concrete shuttering blocks – Product properties and performance

EN 15599-1:2010Thermal insulation products for building equipment and industrial installations – In-situ thermal insulation formed from expanded perlite (EP) products – Part 1: Specification for bonded and loose-fill products before installation

EN 15600-1:2010Thermal insulation products for building equipment and industrial installations – In-situ thermal insulation formed from exfoliated vermiculite (EV) products – Part 1: Specification for bonded and loose-fill products before installation

EN 15650:2010Ventilation for buildings – Fire dampers

EN 15743:2010Supersulfated cement – Composition, specifications and conformity criteria

EN 15821:2010Multi-firing sauna stoves fired by natural wood logs – Requirements and test methods

EN 15824:2009Specifications for external renders and internal plasters based on organic binders

EN 1748-1-2:2004Glass in building – Special basic products – Borosilicate glasses – Part 1-2: Evaluation of conformity/Product standard

EN 1748-2-2:2004Glass in building – Special basic products – Glass ceramics – Part 2-2: Evaluation of conformity/Product standard

EN 179:2008Building hardware – Emergency exit devices operated by a lever handle or push pad, for use on escape routes – Requirements and test methods

EN 1806:2006Chimneys – Clay/ceramic flue blocks for single wall chimneys – Requirements and test methods

EN 1825-1:2004Grease separators – Part 1: Principles of design, performance and testing, marking and quality control

EN 1856-1:2009Chimneys – Requirements for metal chimneys – Part 1: System chimney products

EN 1856-2:2009Chimneys – Requirements for metal chimneys – Part 2: Metal flue liners and connecting flue pipes

EN 1857:2010Chimneys – Components – Concrete flue liners

EN 1858:2008+A1:2011Chimneys – Components – Concrete flue blocks

EN 1863-2:2004Glass in building – Heat strengthened soda lime silicate glass – Part 2: Evaluation of conformity/Product standard

EN 1873:2005Prefabricated accessories for roofing – Individual roof lights of plastics – Product specification and test methods

EN 1916:2002Concrete pipes and fittings, unreinforced, steel fibre and reinforced

EN 1917:2002Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

EN 1935:2002Building hardware – Single-axis hinges – Requirements and test methods

EN 197-1:2011 (new)Cement – Part 1: Composition, specifications and conformity criteria for common cements

EN 295-10:2005Vitrified clay pipes and fittings and pipe joints for drains and sewers – Part 10: Performance requirements

EN 331:1998Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings

EN 40-4:2005Lighting columns – Part 4: Requirements for reinforced and prestressed concrete lighting columns

EN 40-5:2002Lighting columns – Part 5: Requirements for steel lighting columns

EN 40-6:2002Lighting columns – Part 6: Requirements for aluminium lighting columns

EN 413-1:2011Masonry cement – Part 1: Composition, specifications and conformity criteria

EN 416-1:2009Single burner gas-fired overhead radiant tube heaters for non-domestic use – Part 1: Safety

EN 438-7:2005High-pressure decorative laminates (HPL) – Sheets based on thermosetting resins (Usually called Laminates) – Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes

EN 442-1:1995Radiators and convectors – Part 1: Technical specifications and requirements

EN 450-1:2005+A1:2007Fly ash for concrete – Part 1: Definition, specifications and conformity criteria

EN 459-1:2010Building lime – Part 1: Definitions, specifications and conformity criteria

EN 490:2011 (new)Concrete roofing tiles and fittings for roof covering and wall cladding – Product specifications

EN 492:2004Fibre-cement slates and fittings – Product specification and test methods

EN 494:2004+A3:2007Fibre-cement profiled sheets and fittings – Product specification and test methods

EN 516:2006Prefabricated accessories for roofing – Installations for roof access – Walkways, treads and steps

EN 517:2006Prefabricated accessories for roofing – Roof safety hooks

EN 520:2004+A1:2009Gypsum plasterboards – Definitions, requirements and test methods

EN 523:2003Steel strip sheaths for prestressing tendons – Terminology, requirements, quality control

EN 534:2006+A1:2010Corrugated bitumen sheets – Product specification and test methods

EN 54-10:2002Fire detection and fire alarm systems – Part 10: Flame detectors – Point detectors

EN 54-11:2001Fire detection and fire alarm systems – Part 11: Manual call points

EN 54-12:2002Fire detection and fire alarm systems – Part 12: Smoke detectors – Line detectors using an optical light beam

EN 54-16:2008Fire detection and fire alarm systems – Part 16: Voice alarm control and indicating equipment

EN 54-17:2005Fire detection and fire alarm systems – Part 17: Short-circuit isolators

EN 54-18:2005Fire detection and fire alarm systems – Part 18: Input/output devices

EN 54-2:1997Fire detection and fire alarm systems – Part 2: Control and indicating equipment

EN 54-20:2006Fire detection and fire alarm systems – Part 20: Aspirating smoke detectors

EN 54-21:2006Fire detection and fire alarm systems – Part 21: Alarm transmission and fault warning routing equipment

EN 54-23:2010Fire detection and fire alarm systems – Part 23: Fire alarm devices – Visual alarm devices

EN 54-24:2008Fire detection and fire alarm systems – Part 24: Components of voice alarm systems – Loudspeakers

EN 54-25:2008Fire detection and fire alarm systems – Part 25: Components using radio links

EN 54-3:2001Fire detection and fire alarm systems – Part 3: Fire alarm devices – Sounders

EN 54-4:1997Fire detection and fire alarm systems – Part 4: Power supply equipment

EN 544:2011Bitumen shingles with mineral and/or synthetic reinforcements – Product specification and test methods

EN 54-5:2000Fire detection and fire alarm systems – Part 5: Heat detectors – Point detectors

EN 54-7:2000Fire detection and fire alarm systems – Part 7: Smoke detectors – Point detectors using scattered light, transmitted light or ionization

EN 572-9:2004Glass in building – Basic soda lime silicate glass products – Part 9: Evaluation of conformity/Product standard

EN 588-2:2001Fibre cement pipes for drains and sewers – Part 2: Manholes and inspection chambers

EN 598:2007+A1:2009Ductile iron pipes, fittings, accessories and their joints for sewerage applications – Requirements and test methods

EN 621:2009Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products

EN 671-1:2001Fixed firefighting systems – Hose systems – Part 1: Hose reels with semi-rigid hose

EN 671-2:2001Fixed firefighting systems – Hose systems – Part 2: Hose systems with lay-flat hose

EN 681-1:1996Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 1: Vulcanized rubber

EN 681-2:2000Elastomeric Seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 2: Thermoplastic elastomers

EN 681-3:2000Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 3: Cellular materials of vulcanized rubber

EN 681-4:2000Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 4: Cast polyurethane sealing elements

EN 682:2002Elastomeric Seals – Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids

EN 771-1:2011Specification for masonry units – Part 1: Clay masonry units

EN 771-2:2011Specification for masonry units – Part 2: Calcium silicate masonry units

EN 771-3:2011Specification for masonry units – Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)

EN 771-4:2011Specification for masonry units – Part 4: Autoclaved aerated concrete masonry units

EN 771-5:2011Specification for masonry units – Part 5: Manufactured stone masonry units

EN 771-6:2011Specification for masonry units – Part 6: Natural stone masonry units

EN 777-1:2009Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use – Part 1: System D – Safety

EN 777-2:2009Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use – Part 2: System E – Safety

EN 777-3:2009Multi-burner gas-fired overhead radiant tube heater systems for non domestic use – Part 3: System F – Safety

EN 777-4:2009Multi-burner gas-fired overhead radiant tube heater systems for non-domestic use – Part 4: System H – Safety

EN 778:2009Domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 70 kW, without a fan to assist transportation of combustion air and/or combustion products

EN 845-1:2003+A1:2008Specification for ancillary components for masonry – Part 1: Ties, tension straps, hangers and brackets

EN 845-2:2003Specification for ancillary components for masonry – Part 2: Lintels

EN 845-3:2003+A1:2008Specification for ancillary components for masonry – Part 3: Bed joint reinforcement of steel meshwork

EN 858-1:2002Separator systems for light liquids (e.g. oil and petrol) – Part 1: Principles of product design, performance and testing, marking and quality control

EN 877:1999Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings – Requirements, test methods and quality assurance

EN 934-2:2009Admixtures for concrete, mortar and grout – Part 2: Concrete admixtures – Definitions, requirements, conformity, marking and labelling

EN 934-3:2009Admixtures for concrete, mortar and grout – Part 3: Admixtures for masonry mortar – Definitions, requirements, conformity and marking and labelling

EN 934-4:2009Admixtures for concrete, mortar and grout – Part 4: Admixtures for grout for prestressing tendons – Definitions, requirements, conformity, marking and labelling

EN 934-5:2007Admixtures for concrete, mortar and grout – Part 5: Admixtures for sprayed concrete – Definitions, requirements, conformity, marking and labelling

EN 969:2009Ductile iron pipes, fittings, accessories and their joints for gas pipelines – Requirements and test methods

EN 997:2012 (new)WC pans and WC suites with integral trap

EN 998-1:2010Specification for mortar for masonry – Part 1: Rendering and plastering mortar

EN 998-2:2010Specification for mortar for masonry – Part 2: Masonry mortar