Archive for category: ASTM Test

Turf testing in accordance with ASTM method

05 May 2015 Comments
Off

평택 미군기지 공사 관련  UFGS (Unified Facilities Guide Specifications )규격에 따른 인조잔디 시험방법 안내

아래 각 시험항목은 UFGS (Unified Facilities Guide Specifications )의 일부 입니다.

FTIR Scan (Infrared scan)

ASTM D 1907: Standard Test Method for Linear Density of Yarn by the Skein Method (Denier)

ASTM D 1335; Tuft Bind

ASTM D 2256; Tensile Properties by Single-Strand Method (Breaking Strength & Elongation)

ASTM D 2261: Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure Using CRE Tensile Tester

ASTM D 2859; Ignition Characteristics with infill (Pill Burn)

DIN 18-035 Part 6; Water Permeability

ASTM D 5034; Breaking Strength and Elongation (Grab Test)

ASTM D 5793: Standard Test Method for Binding Sites Per Unit Length or Width of Pile Yarn Floor Coverings (Stitch & Gauge)

ASTM D 5823; Tuft Height

ASTM D 5848; Mass per unit Area (Total, Pile, Secondary & Primary Weight)

ASTM E 648; Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat
Energy Source (Turf with infill)

ASTM E 794 Melt & Crystallization Temperatures by Thermal Analysis

ASTM F 355: Standard Test Methods for Shock-Absorbing Properties of Playing Surface  Systems and Materials ( Procedure A) (with infill)

ASTM F 2765 Standard Specification for Total Lead Content in Synthetic Turf Fibers

ASTM F 1015: Standard Test Method for Relative Abrasiveness of Synthetic Turf
Playing Surfaces (with infill)

 

시험시료의 내용은 다음과 같습니다.

  1. 4’ Feet Length X 15’ Feet Width Turf Roll
  2. 1 Cone of Each Yarn Used in Production of Turf

 

[infill & rubber chip]

Infill 1

 

 

 

 

 

 

NFPA 규격 목록

28 Feb 2015 Comments
Off

NFPA ( National Fire Protection Association) 규격목록입니다.

각 규격별 내용은 NFPA 공식 사이트(http://www.nfpa.org/)를 참조하시기 바랍니다.  각 규격에는 해당되는 경우,  규격항목, 시험 및 절차 등이 상세히 기술되어 있습니다.

  • NFPA 1Fire Code
  • NFPA 2Hydrogen Technologies Code
  • NFPA 3Recommended Practice for Commissioning of Fire Protection and Life Safety Systems
  • NFPA 4Standard for Integrated Fire Protection and Life Safety System Testing
  • NFPA 10Standard for Portable Fire Extinguishers
  • NFPA 11Standard for Low-, Medium-, and High-Expansion Foam
  • NFPA 11AStandard for Medium- and High-Expansion Foam Systems
  • NFPA 11CStandard for Mobile Foam Apparatus
  • NFPA 12Standard on Carbon Dioxide Extinguishing Systems
  • NFPA 12AStandard on Halon 1301 Fire Extinguishing Systems
  • NFPA 13Standard for the Installation of Sprinkler Systems
  • NFPA 13DStandard for the Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes
  • NFPA 13ERecommended Practice for Fire Department Operations in Properties Protected by Sprinkler and Standpipe Systems
  • NFPA 13RStandard for the Installation of Sprinkler Systems in Low-Rise Residential Occupancies
  • NFPA 14Standard for the Installation of Standpipe and Hose Systems
  • NFPA 15Standard for Water Spray Fixed Systems for Fire Protection
  • NFPA 16Standard for the Installation of Foam-Water Sprinkler and Foam-Water Spray Systems
  • NFPA 17Standard for Dry Chemical Extinguishing Systems
  • NFPA 17AStandard for Wet Chemical Extinguishing Systems
  • NFPA 18Standard on Wetting Agents
  • NFPA 18AStandard on Water Additives for Fire Control and Vapor Mitigation
  • NFPA 20Standard for the Installation of Stationary Pumps for Fire Protection
  • NFPA 22Standard for Water Tanks for Private Fire Protection
  • NFPA 24Standard for the Installation of Private Fire Service Mains and Their Appurtenances
  • NFPA 25Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems
  • NFPA 30Flammable and Combustible Liquids Code
  • NFPA 30ACode for Motor Fuel Dispensing Facilities and Repair Garages
  • NFPA 30BCode for the Manufacture and Storage of Aerosol Products
  • NFPA 31Standard for the Installation of Oil-Burning Equipment
  • NFPA 32Standard for Drycleaning Plants
  • NFPA 33Standard for Spray Application Using Flammable or Combustible Materials
  • NFPA 34Standard for Dipping, Coating, and Printing Processes Using Flammable or Combustible Liquids
  • NFPA 35Standard for the Manufacture of Organic Coatings
  • NFPA 36Standard for Solvent Extraction Plants
  • NFPA 37Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines
  • NFPA 40Standard for the Storage and Handling of Cellulose Nitrate Film
  • NFPA 42Code for the Storage of Pyroxylin Plastic
  • NFPA 45Standard on Fire Protection for Laboratories Using Chemicals
  • NFPA 46Recommended Safe Practice for Storage of Forest Products
  • NFPA 50Standard for Bulk Oxygen Systems at Consumer Sites
  • NFPA 50AStandard for Gaseous Hydrogen Systems at Consumer Sites
  • NFPA 50BStandard for Liquefied Hydrogen Systems at Consumer Sites
  • NFPA 51Standard for the Design and Installation of Oxygen-Fuel Gas Systems for Welding, Cutting, and Allied Processes
  • NFPA 51AStandard for Acetylene Cylinder Charging Plants
  • NFPA 51BStandard for Fire Prevention During Welding, Cutting, and Other Hot Work
  • NFPA 52Vehicular Gaseous Fuel Systems Code
  • NFPA 53Recommended Practice on Materials, Equipment, and Systems Used in Oxygen-Enriched Atmospheres
  • NFPA 54National Fuel Gas Code
  • NFPA 55Compressed Gases and Cryogenic Fluids Code
  • NFPA 56Standard for Fire and Explosion Prevention During Cleaning and Purging of Flammable Gas Piping Systems
  • NFPA 57Liquefied Natural Gas (LNG) Vehicular Fuel Systems Code
  • NFPA 58Liquefied Petroleum Gas Code
  • NFPA 59Utility LP-Gas Plant Code
  • NFPA 59AStandard for the Production, Storage, and Handling of Liquefied Natural Gas (LNG)
  • NFPA 61Standard for the Prevention of Fires and Dust Explosions in Agricultural and Food Processing Facilities
  • NFPA 67Guide on Explosion Protection for Gaseous Mixtures in Pipe Systems
  • NFPA 68Standard on Explosion Protection by Deflagration Venting
  • NFPA 69Standard on Explosion Prevention Systems
  • NFPA 70National Electrical Code
  • NFPA 70ANational Electrical Code Requirements for One- and Two-Family Dwellings
  • NFPA 70BRecommended Practice for Electrical Equipment Maintenance
  • NFPA 70EStandard for Electrical Safety in the Workplace
  • NFPA 72National Fire Alarm and Signaling Code
  • NFPA 73Standard for Electrical Inspections for Existing Dwellings
  • NFPA 75Standard for the Fire Protection of Information Technology Equipment
  • NFPA 76Standard for the Fire Protection of Telecommunications Facilities
  • NFPA 77Recommended Practice on Static Electricity
  • NFPA 79Electrical Standard for Industrial Machinery
  • NFPA 80Standard for Fire Doors and Other Opening Protectives
  • NFPA 80ARecommended Practice for Protection of Buildings from Exterior Fire Exposures
  • NFPA 82Standard on Incinerators and Waste and Linen Handling Systems and Equipment
  • NFPA 85Boiler and Combustion Systems Hazards Code
  • NFPA 86Standard for Ovens and Furnaces
  • NFPA 86CStandard for Industrial Furnaces Using a Special Processing Atmosphere
  • NFPA 86DStandard for Industrial Furnaces Using Vacuum as an Atmosphere
  • NFPA 87Recommended Practice for Fluid Heaters
  • NFPA 88AStandard for Parking Structures
  • NFPA 88BStandard for Repair Garages
  • NFPA 90AStandard for the Installation of Air-Conditioning and Ventilating Systems
  • NFPA 90BStandard for the Installation of Warm Air Heating and Air-Conditioning Systems
  • NFPA 91Standard for Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Particulate Solids
  • NFPA 92Standard for Smoke Control Systems
  • NFPA 92AStandard for Smoke-Control Systems Utilizing Barriers and Pressure Differences
  • NFPA 92BStandard for Smoke Management Systems in Malls, Atria, and Large Spaces
  • NFPA 96Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations
  • NFPA 97Standard Glossary of Terms Relating to Chimneys, Vents, and Heat-Producing Appliances
  • NFPA 99Health Care Facilities Code
  • NFPA 99BStandard for Hypobaric Facilities
  • NFPA 101Life Safety Code
  • NFPA 101AGuide on Alternative Approaches to Life Safety
  • NFPA 101BCode for Means of Egress for Buildings and Structures
  • NFPA 102Standard for Grandstands, Folding and Telescopic Seating, Tents, and Membrane Structures
  • NFPA 105Standard for the Installation of Smoke Door Assemblies and Other Opening Protectives
  • NFPA 110Standard for Emergency and Standby Power Systems
  • NFPA 111Standard on Stored Electrical Energy Emergency and Standby Power Systems
  • NFPA 115Standard for Laser Fire Protection
  • NFPA 120Standard for Fire Prevention and Control in Coal Mines
  • NFPA 121Standard on Fire Protection for Self-Propelled and Mobile Surface Mining Equipment
  • NFPA 122Standard for Fire Prevention and Control in Metal/Nonmetal Mining and Metal Mineral Processing Facilities
  • NFPA 123Standard for Fire Prevention and Control in Underground Bituminous Coal Mines
  • NFPA 130Standard for Fixed Guideway Transit and Passenger Rail Systems
  • NFPA 140Standard on Motion Picture and Television Production Studio Soundstages, Approved Production Facilities, and Production Locations
  • NFPA 150Standard on Fire and Life Safety in Animal Housing Facilities
  • NFPA 160Standard for the Use of Flame Effects Before an Audience
  • NFPA 170Standard for Fire Safety and Emergency Symbols
  • NFPA 203Guide on Roof Coverings and Roof Deck Constructions
  • NFPA 204Standard for Smoke and Heat Venting
  • NFPA 211Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
  • NFPA 214Standard on Water-Cooling Towers
  • NFPA 220Standard on Types of Building Construction
  • NFPA 221Standard for High Challenge Fire Walls, Fire Walls, and Fire Barrier Walls
  • NFPA 225Model Manufactured Home Installation Standard
  • NFPA 230Standard for the Fire Protection of Storage
  • NFPA 231Standard for General Storage
  • NFPA 231CStandard for Rack Storage of Materials
  • NFPA 231DStandard for Storage of Rubber Tires
  • NFPA 231ERecommended Practice for the Storage of Baled Cotton
  • NFPA 231FStandard for the Storage of Roll Paper
  • NFPA 232Standard for the Protection of Records
  • NFPA 232AGuide for Fire Protection for Archives and Records Centers
  • NFPA 241Standard for Safeguarding Construction, Alteration, and Demolition Operations
  • NFPA 251Standard Methods of Tests of Fire Resistance of Building Construction and Materials
  • NFPA 252Standard Methods of Fire Tests of Door Assemblies
  • NFPA 253Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source
  • NFPA 255Standard Method of Test of Surface Burning Characteristics of Building Materials
  • NFPA 256Standard Methods of Fire Tests of Roof Coverings
  • NFPA 257Standard on Fire Test for Window and Glass Block Assemblies
  • NFPA 258Recommended Practice for Determining Smoke Generation of Solid Materials
  • NFPA 259Standard Test Method for Potential Heat of Building Materials
  • NFPA 260Standard Methods of Tests and Classification System for Cigarette Ignition Resistance of Components of Upholstered Furniture
  • NFPA 261Standard Method of Test for Determining Resistance of Mock-Up Upholstered Furniture Material Assemblies to Ignition by Smoldering Cigarettes
  • NFPA 262Standard Method of Test for Flame Travel and Smoke of Wires and Cables for Use in Air-Handling Spaces
  • NFPA 265Standard Methods of Fire Tests for Evaluating Room Fire Growth Contribution of Textile or Expanded Vinyl Wall Coverings on Full Height Panels and Walls
  • NFPA 266Standard Method of Test for Fire Characteristics of Upholstered Furniture Exposed to Flaming Ignition Source
  • NFPA 267Standard Method of Test for Fire Characteristics of Mattresses and Bedding Assemblies Exposed to Flaming Ignition Source
  • NFPA 268Standard Test Method for Determining Ignitability of Exterior Wall Assemblies Using a Radiant Heat Energy Source
  • NFPA 269Standard Test Method for Developing Toxic Potency Data for Use in Fire Hazard Modeling
  • NFPA 270Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber
  • NFPA 271Standard Method of Test for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
  • NFPA 272Standard Method of Test for Heat and Visible Smoke Release Rates for Upholstered Furniture Components or Composites and Mattresses Using an Oxygen Consumption Calorimeter
  • NFPA 274Standard Test Method to Evaluate Fire Performance Characteristics of Pipe Insulation
  • NFPA 275Standard Method of Fire Tests for the Evaluation of Thermal Barriers
  • NFPA 276Standard Method of Fire Test for Determining the Heat Release Rate of Roofing Assemblies with Combustible Above-Deck Roofing Components
  • NFPA 277Standard Methods of Tests for Evaluating Fire and Ignition Resistance of Upholstered Furniture Using a Flaming Ignition Source
  • NFPA 285Standard Fire Test Method for Evaluation of Fire Propagation Characteristics of Exterior Non-Load-Bearing Wall Assemblies Containing Combustible Components
  • NFPA 286Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
  • NFPA 287Standard Test Methods for Measurement of Flammability of Materials in Cleanrooms Using a Fire Propagation Apparatus (FPA)
  • NFPA 288Standard Methods of Fire Tests of Horizontal Fire Door Assemblies Installed in Horizontal Fire Resistance-Rated Assemblies
  • NFPA 289Standard Method of Fire Test for Individual Fuel Packages
  • NFPA 290Standard for Fire Testing of Passive Protection Materials for Use on LP-Gas Containers
  • NFPA 291Recommended Practice for Fire Flow Testing and Marking of Hydrants
  • NFPA 295Standard for Wildfire Control
  • NFPA 297Guide on Principles and Practices for Communications Systems
  • NFPA 298Standard on Foam Chemicals for Wildland Fire Control
  • NFPA 299Standard for Protection of Life and Property from Wildfire
  • NFPA 301Code for Safety to Life from Fire on Merchant Vessels
  • NFPA 302Fire Protection Standard for Pleasure and Commercial Motor Craft
  • NFPA 303Fire Protection Standard for Marinas and Boatyards
  • NFPA 306Standard for the Control of Gas Hazards on Vessels
  • NFPA 307Standard for the Construction and Fire Protection of Marine Terminals, Piers, and Wharves
  • NFPA 312Standard for Fire Protection of Vessels During Construction, Conversion, Repair, and Lay-Up
  • NFPA 318Standard for the Protection of Semiconductor Fabrication Facilities
  • NFPA 326Standard for the Safeguarding of Tanks and Containers for Entry, Cleaning, or Repair
  • NFPA 328Recommended Practice for the Control of Flammable and Combustible Liquids and Gases in Manholes, Sewers, and Similar Underground Structures
  • NFPA 329Recommended Practice for Handling Releases of Flammable and Combustible Liquids and Gases
  • NFPA 350Guide for Safe Confined Space Entry and Work
  • NFPA 385Standard for Tank Vehicles for Flammable and Combustible Liquids
  • NFPA 386Standard for Portable Shipping Tanks for Flammable and Combustible Liquids
  • NFPA 395Standard for the Storage of Flammable and Combustible Liquids at Farms and Isolated Sites
  • NFPA 400Hazardous Materials Code
  • NFPA 402Guide for Aircraft Rescue and Fire-Fighting Operations
  • NFPA 403Standard for Aircraft Rescue and Fire-Fighting Services at Airports
  • NFPA 405Standard for the Recurring Proficiency of Airport Fire Fighters
  • NFPA 407Standard for Aircraft Fuel Servicing
  • NFPA 408Standard for Aircraft Hand Portable Fire Extinguishers
  • NFPA 409Standard on Aircraft Hangars
  • NFPA 410Standard on Aircraft Maintenance
  • NFPA 412Standard for Evaluating Aircraft Rescue and Fire-Fighting Foam Equipment
  • NFPA 414Standard for Aircraft Rescue and Fire-Fighting Vehicles
  • NFPA 415Standard on Airport Terminal Buildings, Fueling Ramp Drainage, and Loading Walkways
  • NFPA 418Standard for Heliports
  • NFPA 422Guide for Aircraft Accident/Incident Response Assessment
  • NFPA 423Standard for Construction and Protection of Aircraft Engine Test Facilities
  • NFPA 424Guide for Airport/Community Emergency Planning
  • NFPA 430Code for the Storage of Liquid and Solid Oxidizers
  • NFPA 432Code for the Storage of Organic Peroxide Formulations
  • NFPA 434Code for the Storage of Pesticides
  • NFPA 450Guide for Emergency Medical Services and Systems
  • NFPA 471Recommended Practice for Responding to Hazardous Materials Incidents
  • NFPA 472Standard for Competence of Responders to Hazardous Materials/Weapons of Mass Destruction Incidents
  • NFPA 473Standard for Competencies for EMS Personnel Responding to Hazardous Materials/Weapons of Mass Destruction Incidents
  • NFPA 475Recommended Practice for Responding to Hazardous Materials Incidents/Weapons of Mass Destruction
  • NFPA 480Standard for the Storage, Handling, and Processing of Magnesium Solids and Powders
  • NFPA 481Standard for the Production, Processing, Handling, and Storage of Titanium
  • NFPA 482Standard for the Production, Processing, Handling, and Storage of Zirconium
  • NFPA 484Standard for Combustible Metals
  • NFPA 485Standard for the Storage, Handling, Processing, and Use of Lithium Metal
  • NFPA 490Code for the Storage of Ammonium Nitrate
  • NFPA 495Explosive Materials Code
  • NFPA 496Standard for Purged and Pressurized Enclosures for Electrical Equipment
  • NFPA 497Recommended Practice for the Classification of Flammable Liquids, Gases, or Vapors and of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas
  • NFPA 498Standard for Safe Havens and Interchange Lots for Vehicles Transporting Explosives
  • NFPA 499Recommended Practice for the Classification of Combustible Dusts and of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas
  • NFPA 501Standard on Manufactured Housing
  • NFPA 501AStandard for Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities
  • NFPA 502Standard for Road Tunnels, Bridges, and Other Limited Access Highways
  • NFPA 505Fire Safety Standard for Powered Industrial Trucks Including Type Designations, Areas of Use, Conversions, Maintenance, and Operations
  • NFPA 513Standard for Motor Freight Terminals
  • NFPA 520Standard on Subterranean Spaces
  • NFPA 550Guide to the Fire Safety Concepts Tree
  • NFPA 551Guide for the Evaluation of Fire Risk Assessments
  • NFPA 555Guide on Methods for Evaluating Potential for Room Flashover
  • NFPA 556Guide on Methods for Evaluating Fire Hazard to Occupants of Passenger Road Vehicles
  • NFPA 557Standard for Determination of Fire Loads for Use in Structural Fire Protection Design
  • NFPA 560Standard for the Storage, Handling, and Use of Ethylene Oxide for Sterilization and Fumigation
  • NFPA 600Standard on Industrial Fire Brigades
  • NFPA 601Standard for Security Services in Fire Loss Prevention
  • NFPA 610Guide for Emergency and Safety Operations at Motorsports Venues
  • NFPA 650Standard for Pneumatic Conveying Systems for Handling Combustible Particulate Solids
  • NFPA 651Standard for the Machining and Finishing of Aluminum and the Production and Handling of Aluminum Powders
  • NFPA 652Standard on Combustible Dusts
  • NFPA 654Standard for the Prevention of Fire and Dust Explosions from the Manufacturing, Processing, and Handling of Combustible Particulate Solids
  • NFPA 655Standard for Prevention of Sulfur Fires and Explosions
  • NFPA 664Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities
  • NFPA 701Standard Methods of Fire Tests for Flame Propagation of Textiles and Films
  • NFPA 703Standard for Fire Retardant—Treated Wood and Fire–Retardant Coatings for Building Materials
  • NFPA 704Standard System for the Identification of the Hazards of Materials for Emergency Response
  • NFPA 705Recommended Practice for a Field Flame Test for Textiles and Films
  • NFPA 720Standard for the Installation of Carbon Monoxide(CO) Detection and Warning Equipment
  • NFPA 730Guide for Premises Security
  • NFPA 731Standard for the Installation of Electronic Premises Security Systems
  • NFPA 750Standard on Water Mist Fire Protection Systems
  • NFPA 780Standard for the Installation of Lightning Protection Systems
  • NFPA 790Standard for Competency of Third-Party Field Evaluation Bodies
  • NFPA 791Recommended Practice and Procedures for Unlabeled Electrical Equipment Evaluation
  • NFPA 801Standard for Fire Protection for Facilities Handling Radioactive Materials
  • NFPA 803Standard for Fire Protection for Light Water Nuclear Power Plants
  • NFPA 804Standard for Fire Protection for Advanced Light Water Reactor Electric Generating Plants
  • NFPA 805Performance-Based Standard for Fire Protection for Light Water Reactor Electric Generating Plants
  • NFPA 806Performance-Based Standard for Fire Protection for Advanced Nuclear Reactor Electric Generating Plants Change Process
  • NFPA 820Standard for Fire Protection in Wastewater Treatment and Collection Facilities
  • NFPA 850Recommended Practice for Fire Protection for Electric Generating Plants and High Voltage Direct Current Converter Stations
  • NFPA 851Recommended Practice for Fire Protection for Hydroelectric Generating Plants
  • NFPA 853Standard for the Installation of Stationary Fuel Cell Power Systems
  • NFPA 900Building Energy Code
  • NFPA 901Standard Classifications for Incident Reporting and Fire Protection Data
  • NFPA 902Fire Reporting Field Incident Guide
  • NFPA 903Fire Reporting Property Survey Guide
  • NFPA 904Incident Follow-up Report Guide
  • NFPA 906Guide for Fire Incident Field Notes
  • NFPA 909Code for the Protection of Cultural Resource Properties – Museums, Libraries, and Places of Worship
  • NFPA 914Code for Fire Protection of Historic Structures
  • NFPA 921Guide for Fire and Explosion Investigations
  • NFPA 950Standard for Data Development and Exchange for the Fire Service
  • NFPA 951Guide to Building and Utilizing Digital Information
  • NFPA 1000Standard for Fire Service Professional Qualifications Accreditation and Certification Systems
  • NFPA 1001Standard for Fire Fighter Professional Qualifications
  • NFPA 1002Standard for Fire Apparatus Driver/Operator Professional Qualifications
  • NFPA 1003Standard for Airport Fire Fighter Professional Qualifications
  • NFPA 1005Standard for Professional Qualifications for Marine Fire Fighting for Land-Based Fire Fighters
  • NFPA 1006Standard for Technical Rescuer Professional Qualifications
  • NFPA 1021Standard for Fire Officer Professional Qualifications
  • NFPA 1026Standard for Incident Management Personnel Professional Qualifications
  • NFPA 1031Standard for Professional Qualifications for Fire Inspector and Plan Examiner
  • NFPA 1033Standard for Professional Qualifications for Fire Investigator
  • NFPA 1035Standard on Fire and Life Safety Educator, Public Information Officer, Youth Firesetter Intervention Specialist and Youth Firesetter Program Manager Professional Qualifications
  • NFPA 1037Standard for Professional Qualifications for Fire Marshal
  • NFPA 1041Standard for Fire Service Instructor Professional Qualifications
  • NFPA 1051Standard for Wildland Fire Fighter Professional Qualifications
  • NFPA 1061Professional Qualifications for Public Safety Telecommunications Personnel
  • NFPA 1071Standard for Emergency Vehicle Technician Professional Qualifications
  • NFPA 1072Standard for Hazardous Materials/Weapons of Mass Destruction Emergency Response Personnel Professional Qualifications
  • NFPA 1081Standard for Industrial Fire Brigade Member Professional Qualifications
  • NFPA 1091Standard for Traffic Control Incident Management Professional Qualifications
  • NFPA 1122Code for Model Rocketry
  • NFPA 1123Code for Fireworks Display
  • NFPA 1124Code for the Manufacture, Transportation, Storage, and Retail Sales of Fireworks and Pyrotechnic Articles
  • NFPA 1125Code for the Manufacture of Model Rocket and High Power Rocket Motors
  • NFPA 1126Standard for the Use of Pyrotechnics Before a Proximate Audience
  • NFPA 1127Code for High Power Rocketry
  • PYR 1128Standard Method of Fire Test for Flame Breaks
  • PYR 1129Standard Method of Fire Test for Covered Fuse on Consumer Fireworks
  • NFPA 1141Standard for Fire Protection Infrastructure for Land Development in Wildland, Rural, and Suburban Areas
  • NFPA 1142Standard on Water Supplies for Suburban and Rural Fire Fighting
  • NFPA 1143Standard for Wildland Fire Management
  • NFPA 1144Standard for Reducing Structure Ignition Hazards from Wildland Fire
  • NFPA 1145Guide for the Use of Class A Foams in Manual Structural Fire Fighting
  • NFPA 1150Standard on Foam Chemicals for Fires in Class A Fuels
  • NFPA 1192Standard on Recreational Vehicles
  • NFPA 1194Standard for Recreational Vehicle Parks and Campgrounds
  • NFPA 1201Standard for Providing Fire and Emergency Services to the Public
  • NFPA 1221Standard for the Installation, Maintenance, and Use of Emergency Services Communications Systems
  • NFPA 1231Standard on Water Supplies for Suburban and Rural Fire Fighting
  • NFPA 1250Recommended Practice in Fire and Emergency Service Organization Risk Management
  • NFPA 1300Standard for Community Risk Reduction (CRR) Plans
  • NFPA 1401Recommended Practice for Fire Service Training Reports and Records
  • NFPA 1402Guide to Building Fire Service Training Centers
  • NFPA 1403Standard on Live Fire Training Evolutions
  • NFPA 1404Standard for Fire Service Respiratory Protection Training
  • NFPA 1405Guide for Land-Based Fire Departments that Respond to Marine Vessel Fires
  • NFPA 1407Standard for Training Fire Service Rapid Intervention Crews
  • NFPA 1408Standard for Training Fire Service Personnel in the Operation, Care, Use, and Maintenance of Thermal Imagers
  • NFPA 1410Standard on Training for Emergency Scene Operations
  • NFPA 1451Standard for a Fire and Emergency Services Vehicle Operations Training Program
  • NFPA 1452Guide for Training Fire Service Personnel to Conduct Community Risk Reduction
  • NFPA 1500Standard on Fire Department Occupational Safety and Health Program
  • NFPA 1521Standard for Fire Department Safety Officer Professional Qualifications
  • NFPA 1561Standard on Emergency Services Incident Management System and Command Safety
  • NFPA 1581Standard on Fire Department Infection Control Program
  • NFPA 1582Standard on Comprehensive Occupational Medical Program for Fire Departments
  • NFPA 1583Standard on Health-Related Fitness Programs for Fire Department Members
  • NFPA 1584Standard on the Rehabilitation Process for Members During Emergency Operations and Training Exercises
  • NFPA 1600Standard on Disaster/Emergency Management and Business Continuity Programs
  • NFPA 1616Standard for Mass Evacuation and Sheltering
  • NFPA 1620Standard for Pre-Incident Planning
  • NFPA 1670Standard on Operations and Training for Technical Search and Rescue Incidents
  • NFPA 1710Standard for the Organization and Deployment of Fire Suppression Operations, Emergency Medical Operations, and Special Operations to the Public by Career Fire Departments
  • NFPA 1720Standard for the Organization and Deployment of Fire Suppression Operations, Emergency Medical Operations and Special Operations to the Public by Volunteer Fire Departments
  • NFPA 1730Standard on Organization and Deployment of Fire Prevention Inspection and Code Enforcement, Plan Review, Investigation, and Public Education Operations to the Public
  • NFPA 1801Standard on Thermal Imagers for the Fire Service
  • NFPA 1802Standard on Personal Portable (Hand-Held) Two-Way Radio Communications Devices for Use by Emergency Services Personnel in the Hazard Zone
  • NFPA 1851Standard on Selection, Care, and Maintenance of Protective Ensembles for Structural Fire Fighting and Proximity Fire Fighting
  • NFPA 1852Standard on Selection, Care, and Maintenance of Open-Circuit Self-Contained Breathing Apparatus (SCBA)
  • NFPA 1855Standard for Selection, Care, and Maintenance of Protective Ensembles for Technical Rescue Incidents
  • NFPA 1858Standard on Selection, Care, and Maintenance of Life Safety Rope and Equipment for Emergency Services
  • NFPA 1901Standard for Automotive Fire Apparatus
  • NFPA 1906Standard for Wildland Fire Apparatus
  • NFPA 1911Standard for the Inspection, Maintenance, Testing, and Retirement of In-Service Automotive Fire Apparatus
  • NFPA 1912Standard for Fire Apparatus Refurbishing
  • NFPA 1914Standard for Testing Fire Department Aerial Devices
  • NFPA 1915Standard for Fire Apparatus Preventive Maintenance Program
  • NFPA 1917Standard for Automotive Ambulances
  • NFPA 1925Standard on Marine Fire-Fighting Vessels
  • NFPA 1931Standard for Manufacturer’s Design of Fire Department Ground Ladders
  • NFPA 1932Standard on Use, Maintenance, and Service Testing of In-Service Fire Department Ground Ladders
  • NFPA 1936Standard on Powered Rescue Tools
  • NFPA 1951Standard on Protective Ensembles for Technical Rescue Incidents
  • NFPA 1952Standard on Surface Water Operations Protective Clothing and Equipment
  • NFPA 1953Standard on Protective Ensembles for Contaminated Water Diving
  • NFPA 1961Standard on Fire Hose
  • NFPA 1962Standard for the Care, Use, Inspection, Service Testing, and Replacement of Fire Hose, Couplings, Nozzles, and Fire Hose Appliances
  • NFPA 1963Standard for Fire Hose Connections
  • NFPA 1964Standard for Spray Nozzles
  • NFPA 1965Standard for Fire Hose Appliances
  • NFPA 1971Standard on Protective Ensembles for Structural Fire Fighting and Proximity Fire Fighting
  • NFPA 1975Standard on Station/Work Uniforms for Emergency Services
  • NFPA 1976Standard on Protective Ensemble for Proximity Fire Fighting
  • NFPA 1977Standard on Protective Clothing and Equipment for Wildland Fire Fighting
  • NFPA 1981Standard on Open-Circuit Self-Contained Breathing Apparatus (SCBA) for Emergency Services
  • NFPA 1982Standard on Personal Alert Safety Systems (PASS)
  • NFPA 1983Standard on Life Safety Rope and Equipment for Emergency Services
  • NFPA 1984Standard on Respirators for Wildland Fire Fighting Operations
  • NFPA 1986Standard on Respiratory Protection Equipment for Technical and Tactical Operations
  • NFPA 1989Standard on Breathing Air Quality for Emergency Services Respiratory Protection
  • NFPA 1991Standard on Vapor-Protective Ensembles for Hazardous Materials Emergencies
  • NFPA 1992Standard on Liquid Splash-Protective Ensembles and Clothing for Hazardous Materials Emergencies
  • NFPA 1994Standard on Protective Ensembles for First Responders to CBRN Terrorism Incidents
  • NFPA 1999Standard on Protective Clothing for Emergency Medical Operations
  • NFPA 2001Standard on Clean Agent Fire Extinguishing Systems
  • NFPA 2010Standard for Fixed Aerosol Fire-Extinguishing Systems
  • NFPA 2112Standard on Flame-Resistant Garments for Protection of Industrial Personnel Against Flash Fire
  • NFPA 2113Standard on Selection, Care, Use, and Maintenance of Flame-Resistant Garments for Protection of Industrial Personnel Against Short-Duration Thermal Exposures
  • NFPA 5000Building Construction and Safety Code
  • NFPA 8501Standard for Single Burner Boiler Operation
  • NFPA 8502Standard for the Prevention of Furnace Explosions/Implosions in Multiple Burner Boilers
  • NFPA 8503Standard for Pulverized Fuel Systems
  • NFPA 8504Standard on Atmospheric Fluidized-Bed Boiler Operation
  • NFPA 8505Standard for Stoker Operation
  • NFPA 8506Standard on Heat Recovery Steam Generator Systems

 

Synthetic turf

27 Dec 2014 Comments
Off

Product : Synthetic turf 

아래는 UFGS 관련 인조잔디에 대한 적합성 시험항목입니다.

1. Yarn Number Based on Short-Length Specimens ASTM D1059-01

2. Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (CRE Testing Machine) ASTM D2261-11

3. Identification of Fibers in Textiles ASTM D276-00a (2008)

4. Tuft Bind of Pile Yarn Floor Coverings ASTM D1335-12

5. Tensile Properties of Yarns by the Single-Strand Method . Option A (Straight) ASTM D2256/D2256M-10

6. Ignition Characteristics of Finished Textile Floor Covering Materials ASTM D2859-06

7. Water Permeability of Geotextiles by Permittivity ASTM D4491 – 99a (2014)e1

8. Breaking Strength and Elongation of Textile Fabrics (Grab Test) ASTM D5034-09 (2013)

9. Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings ASTM D5793-05

10. Tuft Height of Pile Floor Coverings ASTM D5823-05a11

11. Mass Per Unit Area of Pile Yarn Floor Coverings – Total Mass per Unit Area ASTM D5848-10e1 Section 7

12. Mass Per Unit Area of Pile Yarn Floor Coverings – Component Masses per Unit Area ASTM D5848-10e1 Section 8

13. Mass Per Unit Area of Pile Yarn Floor Coverings – Pile Yarn Mass per Unit Area ASTM D5848-10e1 Section 9

14. Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source ASTM E 648-10e¹

15. Melting and Crystallization Temperature by Thermal Analysis ASTM E794-06 (2012)

16. Relative Abrasiveness of Synthetic Turf Playing Surfaces ASTM F1015-03 (2009)

 

ASTM D6878 – on TPO membrane Analysis

건축자재 인증 및 시험 관련 규격

Download : Analysis of one TPO membrane per ASTM D6878_D6878M-13

Analysis of one TPO membrane per ASTM D6878/D6878M-13.

아래는 적용되는 분석기법입니다.

    1. ASTM D 6878/D : Brittleness Point per ASTM D2137, Method B
    2. ASTM D 6878/D : Ozone Resistance per ASTM D 1149 (Exposed to 100 mPa ozone in air @40°C, wrapped around a 3″ mandrel for 166 hrs exposure) – OUTSOURCED
    3. ASTM D 6878/D : Breaking Strength per ASTM D751, grab method – MD
    4. ASTM D 6878/D : Breaking Strength per ASTM D751, grab method – XMD
    5. ASTM D 6878/D : Elongation at Reinforcement Break per ASTM D751, grab method – MD
    6. ASTM D 6878/D : Elongation at Reinforcement Break per ASTM D751, grab method – XMD
    7. ASTM D 6878/D : Factory Seam Strength @ 2 in/min (12 in x 1 in specimen) per ASTM D751,grab method
    8. ASTM D 6878/D : Heat Aging, 5376 hrs (224 days) @ 116°C, per ASTM D573
    9. ASTM D 6878/D : Linear Dimensional Change, 6 hr @ 70°C (158°F), per ASTM D1204
    10. ASTM D 6878/D : Post Heat Aging: Breaking Strength per ASTM D751, grab method – MD
    11. ASTM D 6878/D : Post Heat Aging: Breaking Strength per ASTM D751, grab method – XMD
    12. ASTM D 6878/D : Post Heat Aging: Elongation at Reinforcement Break per ASTM D751, grab method – MD
    13. ASTM D 6878/D : Post Heat Aging: Elongation at Reinforcement Break per ASTM D751, grab method – XMD
    14. ASTM D 6878/D : Post Heat Aging: Tearing Strength, 2 in/min (8 in x 8 in specimen) per ASTMD751 – MD
    15. ASTM D 6878/D : Post Heat Aging: Tearing Strength, 2 in/min (8 in x 8 in specimen) per ASTMD751 – XMD
    16. ASTM D 6878/D : Post Heat Aging: Weight Change (mass)
    17. ASTM D 6878/D : Tearing Strength, 2 in/min (8 in x 8 in specimen), per ASTM D751 – MD
    18. ASTM D 6878/D : Tearing Strength, 2 in/min (8 in x 8 in specimen), per ASTM D751 – XMD
    19. ASTM D 6878/D : Thickness, Coating Over Fabric or Scrim (weathering side only) per ASTM D7635
    20. ASTM D 6878/D : Thickness, Sheet-Overall per ASTM D751
    21. ASTM D 6878/D : Water Absorption, 166 hrs @ 70°C (158°F) (mass) per ASTM D471 – Performed on top coating material ONLY
    22. ASTM D 6878/D : Weather Resistance per ASTM G 155 at 0.35 W/(m²•nm) at 340 nm (8000 hrs)

22. MISCELLANEOUS MATERIALS

건설자재 시험 및 인증 관련 규격목록 22

22. MISCELLANEOUS MATERIALS

22-1)        ANSI A108.10-2009 ; Installation of Grout in Tilework;

22-2)        ANSI A108.1-2009 ; Specification for the Installation of Ceramic Tile with Portland Cement Mortar;

22-3)        ANSI A108.4-2009 ; Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile Setting Epoxy Adhesive;

22-4)        ANSI A108.5-2009 ; Installation of Ceramic Tile with Dry-Set Portland Cement Mortar or Latex-Portland Cement Mortar;

22-5)        ANSI A108.6-2009 ; Installation of Ceramic Tile with Chemical Resistant, Water Cleanable Tile Setting and Grouting Epoxy;

22-6)        ANSI A108.7-2009 ; Specification for Electrically Conductive Ceramic Tile Installed with Conductive Dry-Set Portland Cement Mortar;

22-7)        ANSI A108.8-2009 ; Installation of Ceramic Tile with Chemical Resistant Furan Mortar and Grout;

22-8)        ANSI A108.9-2009 ; Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout;

22-9)        ANSI A118.1-2009 ; Specification for Dry-Set Portland Cement Mortar;

22-10)      ANSI A118.2-2009 ; Specifications for Conductive Dry-set Portland Cement Mortar;

22-11)      ANSI A118.3-2009 ; Specifications for Chemical Resistant Water Cleanable Tile Setting and Grouting Epoxy and Water Cleanable Tile Setting Epoxy Adhesive;

22-12)      ANSI A118.4-2009 ; Specifications Furan Latex – Portland Cement Mortar;

22-13)      ANSI A118.5-2009 ; Specifications for Chemical Resistant Furan;

22-14)      ANSI A118.6-2009 ; Specifications for Ceramic Tile Grouts;

22-15)      ANSI A118.8-2009 ; Specifications for Modified Epoxy Emulsion Mortar/Grout;

22-16)      ANSI A136.1-2009 ; Organic Adhesives for Installation of Ceramic Tile;

22-17)      ANSI A137.1-2008 ; Specification for Ceramic Tile;

22-18)      ANSI A137.1-2008 ; Specifications for Ceramic Tile;

22-19)      ANSI Z 97.1-2009 ; Safety Performance Specifications and Methods of Tests for Transport Safety Glazing Materials Used in Building;

22-20)      ASTM A116 – 05 ASTM A121 – 07 ; Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

22-21)      ASTM A121 – 07 ; Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

22-22)      ASTM A368 – 95a(2009) ; Standard Specification for Stainless Steel Wire Strand

22-23)      ASTM A392 – 07 ; Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric

22-24)      ASTM A475 – 03(2009)e1 ; Standard Specification for Zinc-Coated Steel Wire Strand

22-25)      ASTM A492 – 95(2009) ; Standard Specification for Stainless Steel Rope Wire

22-26)      ASTM A510 – 08 ; Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

22-27)      ASTM A586 – 04a(2009)e1 ; Standard Specification for Zinc-Coated Parallel and Helical Steel Wire Structural Strand

22-28)      ASTM A603 – 98(2009)e1 ; Standard Specification for Zinc-Coated Steel Structural Wire Rope

22-29)      ASTM A817 – 07 ; Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire

22-30)      ASTM A824 – 01(2007) ; Standard Specification for Metallic-Coated Steel Marcelled Tension Wire for Use With Chain Link Fence

22-31)      ASTM C1014 – 08 ; Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation

22-32)      ASTM C1029 – 09 ; Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

22-33)      ASTM C1036 – 06 ; Standard Specification for Flat Glass

22-34)      ASTM C1048 – 04 ; Standard Specification for Heat-Treated Flat Glass—Kind HS, Kind FT Coated and Uncoated Glass

22-35)      ASTM C1071 – 05e1 ; Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material)

22-36)      ASTM C1193 – 09 ; Standard Guide for Use of Joint Sealants

22-37)      ASTM C1193 – 09 ; Standard Guide for Use of Joint Sealants

22-38)      ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

22-39)      ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

22-40)      ASTM C1363 – 05 ; Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus

22-41)      ASTM C167 – 09 ; Standard Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations

22-42)      ASTM C177 – 04 ; Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

22-43)      ASTM C195 – 07 ; Standard Specification for Mineral Fiber Thermal Insulating Cement

22-44)      ASTM C196 – 00(2005) ; Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement

22-45)      ASTM C208 – 08a ; Standard Specification for Cellulosic Fiber Insulating Board

22-46)      ASTM C209 – 07ae1 ; Standard Test Methods for Cellulosic Fiber Insulating Board

22-47)      ASTM C240 – 08e1 ; Standard Test Methods of Testing Cellular Glass Insulation Block

22-48)      ASTM C335 – 05ae1 ; Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation

22-49)      ASTM C411 – 05 ; Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation

22-50)      ASTM C449 – 07 ; Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement

22-51)      ASTM C509 – 06 ; Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material

22-52)      ASTM C516 – 08 ; Standard Specification for Vermiculite Loose Fill Thermal Insulation

22-53)      ASTM C518 – 04 ; Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

22-54)      ASTM C520 – 04 ; Standard Test Methods for Density of Granular Loose Fill Insulations

22-55)      ASTM C533 – 09 ; Standard Specification for Calcium Silicate Block and Pipe Thermal Insulation

22-56)      ASTM C534 / C534M – 08 ; Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form

22-57)      ASTM C542 – 05 ; Standard Specification for Lock-Strip Gaskets

22-58)      ASTM C547 – 07e1 ; Standard Specification for Mineral Fiber Pipe Insulation

22-59)      ASTM C549 – 06 ; Standard Specification for Perlite Loose Fill Insulation

22-60)      ASTM C552 – 07 ; Standard Specification for Cellular Glass Thermal Insulation

22-61)      ASTM C553 – 08 ; Standard Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications

22-62)      ASTM C564 – 09a ; Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

22-63)      ASTM C578 – 09e1 ; Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

22-64)      ASTM C591 – 09 ; Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation

22-65)      ASTM C592 – 08a ; Standard Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type)

22-66)      ASTM C610 – 09e1 ; Standard Specification for Molded Expanded Perlite Block and Pipe Thermal Insulation

22-67)      ASTM C612 – 09 ; Standard Specification for Mineral Fiber Block and Board Thermal Insulation

22-68)      ASTM C665 – 06 ; Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing

22-69)      ASTM C716 – 06 ; Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials

22-70)      ASTM C719 – 93(2005) ; Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)

22-71)      ASTM C726 – 05e1 ; Standard Specification for Mineral Fiber Roof Insulation Board

22-72)      ASTM C728 – 05(2010) ; Standard Specification for Perlite Thermal Insulation Board

22-73)      ASTM C739 – 08 ; Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

22-74)      ASTM C764 – 07 ; Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation

22-75)      ASTM C794 – 06 ; Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants

22-76)      ASTM C834 – 10 ; Standard Specification for Latex Sealants

22-77)      ASTM C864 – 05 ; Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers

22-78)      ASTM C916 – 85(2007) ; Standard Specification for Adhesives for Duct Thermal Insulation

22-79)      ASTM C919 – 08 ; Standard Practice for Use of Sealants in Acoustical Applications

22-80)      ASTM C920 – 08 ; Standard Specification for Elastomeric Joint Sealants

22-81)      ASTM C991 – 08e1 ; Standard Specification for Flexible Fibrous Glass Insulation for Metal Buildings

22-82)      ASTM D1003 – 07e1 ; Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics

22-83)      ASTM D1044 – 08 ; Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion

22-84)      ASTM D1204 – 08 ; Standard Test Method for Linear Dimensional Changes of Nonrigid

22-85)      ASTM D1327 – 04 ; Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing

22-86)      ASTM D146 – 04 ; Standard Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing

22-87)      ASTM D1593 – 09 ; Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting

22-88)      ASTM D1668 – 97a(2006) ; Standard Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing

22-89)      ASTM D173 – 03 ; Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing

22-90)      ASTM D2103 – 08 ; Standard Specification for Polyethylene Film and Sheeting

22-91)      ASTM D2126 – 09 ; Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

22-92)      ASTM D2178 – 04 ; Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

22-93)      ASTM D226 / D226M – 09 ; Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

22-94)      ASTM D227 – 03 ; Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

22-95)      ASTM D25 – 99(2005) ; Standard Specification for Round Timber Piles

22-96)      ASTM D2626 – 04 ; Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

22-97)      ASTM D2628 – 91(2005) ; Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements

22-98)      ASTM D2842 – 06 ; Standard Test Method for Water Absorption of Rigid Cellular Plastics

22-99)      ASTM D2843 – 10 ; Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics

22-100)    ASTM D3294 – 09 ; Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes

22-101)    ASTM D3406 – 95(2006) ; Standard Specification for Joint Sealant, Hot-Applied, Elastomeric-Type, for Portland Cement Concrete Pavements

22-102)    ASTM D3468 – 99(2006)e1 ; Standard Specification for Liquid-Applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing

22-103)    ASTM D3667 – 05 ; Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors

22-104)    ASTM D3678 – 97(2008)e1 ; Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions

22-105)    ASTM D3679 – 09a ; Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding

22-106)    ASTM D3771 – 03(2007) ; Standard Specification for Rubber Seals Used in Concentrating Solar Collectors

22-107)    ASTM D3832 – 79(2006) ; Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems

22-108)    ASTM D3841 – 97(2008)e1 ; Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels

22-109)    ASTM D41 – 05 ; Standard Specification for Asphalt Primer Used in Roofing, Damp proofing, and Waterproofing

22-110)     ASTM D43 – 00(2006) ; Standard Specification for Coal Tar Primer Used in Roofing, Damp proofing, and Waterproofing

22-111)     ASTM D449 – 03(2008) ; Standard Specification for Asphalt Used in Damp proofing and Waterproofing

22-112)     ASTM D450 – 07 ; Standard Specification for Coal-Tar Pitch Used in Roofing, Damp proofing, and Waterproofing

22-113)     ASTM D4802 – 02 ; Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet

22-114)     ASTM D543 – 06 ; Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

22-115)     ASTM D635 – 06 ; Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

22-116)     ASTM D638 – 08 ; Standard Test Method for Tensile Properties of Plastics

22-117)     ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

22-118)     ASTM D6690 – 07 ; Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

22-119)     ASTM D695 – 08 ; Standard Test Method for Compressive Properties of Rigid Plastics

22-120)    ASTM D882 – 09 ; Standard Test Method for Tensile Properties of Thin Plastic Sheeting

22-121)    ASTM E119 – 09c ; Standard Test Methods for Fire Tests of Building Construction and Materials

22-122)    ASTM E84 – 10 ; Standard Test Method for Surface Burning Characteristics of Building Materials

22-123)    ASTM F1183 – 96(2006) ; Standard Specification for Aluminum Alloy Chain Link Fence Fabric

22-124)    BDS 1301 : 1990 ; Specification for Glazed Earthenware Wall Tiles;

22-125)    BDS 1301:1990 ; Specification for Glazed Earthenware Wall Tiles;

22-126)    BDS 1493:1994 ; Glossary of terms used in refractory

22-127)    BDS 1494:1994 ; Dimension of refractory bricks

22-128)    BDS 1495:1994 ; High aluminium refractory bricks

22-129)    BDS 809:1973 ; Specification for Wood Poles for Overhead Power and Telecommunication Lines;

22-130)    BDS 885:1979 ; Method for Measuring Viscosity Number and K-Value of PVC Resins;

22-131)    BDS 886:1978 ; Method for Direct Measuring the Specific Gravity of Plastics;

22-132)    BDS 887:1978 ; Method for Measuring Deformation under Heat of Flexible Rigid PVC Compounds;

22-133)    BDS 888:1978 ; Method for Measuring Temperature of Deflection under Load;

22-134)    BDS 889:1978 ; Method for Measuring the Vicat Softening Temperature (VST) of Thermoplastics;

22-135)    BDS 890:1978 ; Method for Measuring the Water Absorption at Room Temperature and Bolling Water Absorption of Plastics;

22-136)    BDS 891:1978 ; Method for Measuring the Flexural Modulus of Plastics;

22-137)    BDS 892:1978 ; Method for Measuring the Resistance to Tear Propagation of Flexible Plastics, Film or Sheeting;

22-138)    BS 6431 ; Floor and Wall Tiles;

22-139)    BS 6431 Part 1 1983 ; Specification for Classification and Making, Including Definitions and Characteristics;

22-140)    BS 6431 Part 1 to Part 23 ; Ceramic Floor and Wall Tiles.

22-141)    BS 6431 Part 10 1984 ; Method for Determination of Dimensions and Surface Quality;

22-142)    BS 6431 Part 11 1983 ; Method for Determination of Water Absorption;

22-143)    BS 6431 Part 12 1983 ; Method for Determination of Modulus of;

22-144)    BS 6431 Part 13 1986 ; Method for Determination of Scratch Hardness of Surface According to Mhos;

22-145)    BS 6431 Part 14 1983 ; Method for Determination of Resistance to Abrasion of Unglazed Tiles;

22-146)    BS 6431 Part 15 1983 ; Method for Determination of Linear Thermal Expansion;

22-147)    BS 6431 Part 16 1983 ; Method for Determination of Resistance to Thermal Shock;

22-148)    BS 6431 Part 17 1983 ; Method for Determination of Crazing Resistance-Glazed Tiles;

22-149)    BS 6431 Part 18 1983 ; Method for Determination of Chemical Resistance-Unglazed Tiles;

22-150)    BS 6431 Part 19 1984 ; Method for Determination of Chemical Resistance-Unglazed Tiles;

22-151)    BS 6431 Part 2 1984 ; Specification for Struded Ceramic Tiles with Low Water Absorption (E< 3%) Group A1;

22-152)    BS 6431 Part 20 1984 ; Method for Determination of Resistance to Surface Abrasion-Glazed Tiles;

22-153)    BS 6431 Part 23 1986 ; Specification for Sampling and Basis for Acceptance;

22-154)    BS 6431 Part 3 ; Extruded Ceramic Tiles with a Water Absorption of 3% < 6%. Group A 11a;

22-155)    BS 6431 Part 3 Section 3.1 1986 ; Specification for General Products;

22-156)    BS 6431 Part 3 Section 3.2 1986 ; Specification for Products Terre Cuite, Cotto, Baldosion Catalan;

22-157)    BS 6431 Part 4 ; Extruded Ceramic Tiles with a Water Absorption of 6% <E< 10%. Group A11b;

22-158)    BS 6431 Part 4 ; Section 4.2 1986

22-159)    BS 6431 Part 4 ; Specification for General Products;

22-160)   BS 6431 Part 5 1986 ; Specification for Extruded Ceramic Tiles with a Water Absorption of E>10%, Group A111;

22-161)    BS 6431 Part 6 1984 ; Specification for Dust-prestressed Ceramic Tiles with a Low-Water Absorption (E<3%)Group B1;

22-162)   BS 6431 Part 7 1986 ; Specification for Dust-prestressed Ceramic Tiles with a Water Absorption of 3% <E £ 6%. Group B11a;

22-163)   BS 6431 Part 8 1986 ; Specification for Dust-prestressed Ceramic Tiles with Water Absorption of 6% < E £ 10%. Group B11b;

22-164)    BS 6431 Part 9 1984 ; Specification for Dust-Prestressed Ceramic Tiles with a Water Absorption of E >10%. Group B111;

22-165)    IS 10102:1982 ; Technical supply conditions for Rivets.

22-166)    IS 110:1968 ; Specification for Ready Mixed Paint, Brushing, Grey Filler, for Enamels, for Use Over Primers (First Revision);

22-167)    IS 1900:1974 ; Method of Testing Wood Poles;

22-168)    IS 1902:1961 ; Code of Practice for Preservation of Bamboo and Cane for Non-structural Purposes;

22-169)    IS 1929:1982 ; Specification for Hot Forged Steel Rivets for Hot Closing (12 to 36 mm diameter) (First Revision);

22-170)    IS 2155:1982 ; Specification for Cold-Forged Solid Steel Rivets for Hot Closing (6 to 16 mm diameter) (First Revision);

22-171)    IS 2365:1977 ; Specification for Steel Wire Suspension Ropes for Lifts, Elevators and Hoists (First Revision).

22-172)    IS 2643:1975 ; Dimensions for Pipe Threads for Fastening Purposes;

22-173)    IS 2907:1964 ; Specification for Non-ferrous Rivets (1.6 mm to 10 mm)

22-174)    IS 2998:1981 ; Specification for Cold Forged Steel Rivets for Cold Closing (1 to 16 mm diameter) (First Revision);

22-175)    IS 3337:1978 ; Specification for Ballies for General Purposes (First Revision);

22-176)    IS 345:1952 ; Specification for Wood Filler, Transparent, Liquid;

22-177)    IS 3709:1966 ; Specification for Mastic Cement for Bedding of Metal Windows;

22-178)    IS 419:1967 ; Specification for Putty for Use on Window Frames (First Revision);

22-179)    IS 421:1953 ; Specification for Jointing Paste, for Bedding Moldings on Coaching Stock;

22-180)    IS 423:1961 ; Specification for Plastic Wood, for Joiners’ Filler (revised);

22-181)    IS 424:1965 ; Specification for Plastic Asphalt (revised);

22-182)    IS 554:1975 ; Dimensions for Pipe Threads where Pressure Tight Joints are Required on the Threads (Second Revision);

22-183)    IS 6711:1972 ; Code of Practice for Maintenance of Wood Poles for Overhead Power and Telecommunications Lines.

22-184)    IS 6874:1973 ; Method of Tests for Round Bamboos;

22-185)    IS 7164:1973 ; Specification for Stopper.

22-186)    IS 8242:1976 ; Methods of Tests for Split Bamboo;

22-187)    IS 8295:1976 ; Specification for Bamboo Chicks, Part I Fine;

22-188)    IS 9096:1979 ; Code of Practice for Preservation of Bamboos for Structural Purposes.

22-189)    ISO 10080:1990 ; Refractory Products-Classification of Dense, Shaped Acid-Resisting Products;

22-190)    ISO 10081:1991 ; Basic Refractory Products-Classification-Part I: Products Containing Less Than 7% Residual Carbon.

22-191)    ISO 10563:1991 ; Building Construction-Sealants for Joints-Determination of Change in Mass and Volume;

22-192)    ISO 10590:1991 ; Building Construction-Sealants-Determination of Adhesion/Cohesion Properties at Maintained Extension after Immersion in Water;

22-193)    ISO 10591 : 1991 ; Building Construction-Sealants-Determination of Adhesion/Cohesion Properties after Immersion in Water.

22-194)    ISO 1109:1975 ; Refractory Products-Classification of Dense Shaped Refractory Products;

22-195)    ISO 1146:1988 ; Pyrometric Reference Cones for Laboratory Use-Specification;

22-196)    ISO 1893:1989 ; Refractory Products-Determination of Refractoriness-Under-Load (differential with rising temperature);

22-197)    ISO 1927:1984 ; Prepared Unshaped Refractory Materials (Dense and Insulating) Classification;

22-198)    ISO 2245:1990 ; Shaped Insulating Refractory Products-Classification;

22-199)    ISO 2444 : 1988 ; Joints in Buildings-Vocabulary;

22-200)    ISO 2477:1987 ; Shaped Insulating Refractory Products-Determination of Permanent Change in Dimensions on Heating;

22-201)    ISO 2478:1987 ; Dense Shaped Refractory Products-Determination of Permanent Change in Dimensions on Heating;

22-202)    ISO 3187:1989 ; Refractory Products-Determination of Creep in Compression;

22-203)    ISO 3867:1982 ; Agglomerated Cork-Material of Expansion Joints for Construction and Building Test-Methods;

22-204)    ISO 3869:1981 ; Agglomerated Cork-Filler Material of Expansion Joints for Construction and Buildings -Characteristics, Sampling and Packing;

22-205)    ISO 3934:1978 ; Rubber Building Gaskets-Materials in Preformed Solid Vulcanizates Used for Sealing Glazing and Panels-Specification;

22-206)    ISO 3934:1978 ; Rubber Building Gaskets-Materials in Preformed Solid Vulcanizates Used for Sealing Glazing and Panels-Specification;

22-207)    ISO 4633:1983 ; Rubber Seals-Joint Rings for Water Supply, Drainage and Sewerage Pipelines-Specification for Materials;

22-208)    ISO 4633:1983 ; Rubber Seals-Joint Rings for Water Supply, Drainage and Sewerage Pipelines-Specifications for Materials;

22-209)    ISO 4635:1982 ; Rubber, Vulcanized-Preformed Compression Seals for Use

22-210)    ISO 4635:1982 ; Rubber, Vulcanized-Preformed Compression Seals for Use Between Concrete Motorway Paving Sections-Specification for Material;

22-211)     ISO 5013:1985 ; Refractory Products-Determination of Modulus of Rupture at Elevated Temperatures;

22-212)    ISO 5014:1986 ; Refractory Products-Determination of Modulus of Rupture at Ambient Temperature;

22-213)    ISO 5015-6:1984 ; Refractory Bricks-Dimensions-Part 6: Basic Bricks for Oxygen Steel Making Converters;

22-214)    ISO 5016:1986 ; Shaped Insulating Refractory Products-Determination of Bulk Density and True Porosity;

22-215)    ISO 5017:1988 ; Dense Shaped Refractory Products-Determination of Bulk Density,

22-216)    ISO 5018:1983 ; Refractory Materials-Determination of True Density;

22-217)    ISO 5019-1:1984 ; Refractory Bricks-Dimensions-Part I: Rectangular Bricks;

22-218)    ISO 5019-2:1984 ; Refractory Bricks-Dimensions-Part 2: Arch Bricks;

22-219)    ISO 5019-3:1984 ; Refractory Bricks-Dimensions-Part 3: Rectangular Checker Bricks for Regenerative Furnace;

22-220)    ISO 5022:1979 ; Shaped Refractory Products-Sampling and Acceptance Testing;

22-221)    ISO 528:1983 ; Refractory Products-Determination of Pyrometric Cone Equivalent (refractoriness);

22-222)    ISO 5417-1986 ; Refractory Bricks for Use in Rotary Kilns-Dimensions;

22-223)    ISO 5419-4:1988 ; Refractory Bricks-Dimensions-Part 4: Dome Bricks for Electric arc Furnace Roofs;

22-224)    ISO 5892:1981 ; Rubber Building Gaskets-Materials for Preformed Solid Vulcanized Structural Gaskets-Specification;

22-225)    ISO 5892:1981 ; Rubber Building Gaskets-Materials for Preformed Solid Vulcanized Structural Gaskets-Specification;

22-226)    ISO 6447:1983 ; Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings-Specification for Material;

22-227)    ISO 6447:1991 ; Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings- Specification for Material;

22-228)    ISO 6589:1983 ; Joints in Building-Laboratory Method of Test for Air Permeability of Joints;

22-229)    ISO 7389:1987 ; Building Construction-Jointing Products-Determination of Elastic Recovery;

22-230)    ISO 7390:1987 ; Building Construction-Jointing Products-Determination of Resistance to Flow;

22-231)    ISO 7727:1984 ; Joints in Building-Principles for Jointing of Building Components-Accommodation of Dimensional Deviations During Construction;

22-232)    ISO 8339:1984 ; Building Construction-Jointing Products-Sealants-Determination of Tensile Properties;

22-233)    ISO 8340:1984 ; Building Construction-Jointing Products-Sealants-Determination of Tensile Properties at Maintained Extension;

22-234)    ISO 8394:1988 ; Building Construction-Jointing Products-Determination of Extrudability of One-Component Sealants;

22-235)    ISO 8656:1988 ; Refractory Products-Sampling of Raw Materials and Unshaped Products;

22-236)    ISO 8840:1987 ; Refractory Materials-Determination of Bulk Density of Granular Materials (Grain Density);

22-237)    ISO 8890:1988 ; Dense Shaped Refractory Products-Determination of Resistance to Sulfuric Acid;

22-238)    ISO 8894-1:1987 ; Refractory Materials-Determination of Thermal Conductivity-

22-239)    ISO 8894-2:1990 ; Refractory Materials-Determination of Thermal Conductivity-

22-240)    ISO 8895:1986 ; Shaped Insulating Refractory Products-Determination of Cold Crushing Strength;

22-241)    ISO 9046:1987 ; Building Construction-Sealants-Determination of Adhesion/ Cohesion Properties at Constant Temperature;

22-242)    ISO 9047:1989 ; Building Construction-Sealants-Determination of Adhesion/ Cohesion Properties at Variable Temperatures;

22-243)    ISO 9205:1988 ; Refractory Bricks for Use in Rotary Kilns-Hot-face Identification Marking;

22-244)    ISO 9331:1991 ; Rubber Seals Joint Rings for Hot Water Supply Pipelines up to 110oC Specifications for the Material.

22-245)    ISO 9631:1991 ; Rubber Seals-Joint Rings for Hot Water Supply Pipelines up to 110oC Specifications for the Material;1-1)             ANSI A108.1-2009 ; Specifications for the Installation of Ceramic Tile with Portland Cement Mortar;

21. SANITARY APPLIANCES AND WATER FITTINGS

건설자재 시험 및 인증 관련 규격목록 21

21. SANITARY APPLIANCES AND WATER FITTINGS

21-1)        ASTM A377 – 03(2008)e1 ; Standard Index of Specifications for Ductile-Iron Pressure Pipe

21-2)        ASTM A53 / A53M – 07 ; Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

21-3)        ASTM A74 – 09 ; Standard Specification for Cast Iron Soil Pipe and Fittings

21-4)        ASTM B209 – 07 ; Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

21-5)        ASTM B251 – 02e1 ; Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube

21-6)        ASTM B302 – 07 ; Standard Specification for Threadless Copper Pipe, Standard Sizes

21-7)        ASTM B306 – 09 ; Standard Specification for Copper Drainage Tube (DWV)

21-8)        ASTM B42 – 02e1 ; Standard Specification for Seamless Copper Pipe, Standard Sizes

21-9)        ASTM B42 – 02e1 ; Standard Specification for Seamless Copper Pipe, Standard Sizes

21-10)      ASTM B429 / B429M – 06 ; Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube

21-11)      ASTM B43 – 09 ; Standard Specification for Seamless Red Brass Pipe, Standard Sizes

21-12)      ASTM B447 – 07 ; Standard Specification for Welded Copper Tube

21-13)      ASTM B745 / B745M – 97(2005) ; Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

21-14)      ASTM B75 – 02 ; Standard Specification for Seamless Copper Tube

21-15)      ASTM B88 – 09 ; Standard Specification for Seamless Copper Water Tube

21-16)      ASTM C14 – 07 ; Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe

21-17)      ASTM C425 – 04(2009) ; Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings

21-18)      ASTM C443 – 05ae1 ; Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

21-19)      ASTM C508 / C508M – 00(2009)e1 ; Standard Specification for Asbestos-Cement Underdrain Pipe

21-20)      ASTM C564 – 09a ; Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

21-21)      ASTM C654 – 05a ; Standard Specification for Porous Concrete Pipe

21-22)      ASTM C700 – 09 ; Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

21-23)      ASTM C76 – 10a ; Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

21-24)      ASTM D1527 – 99(2005) ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

21-25)      ASTM D1785 – 06 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120

21-26)      ASTM D1869 – 95(2005)e1 ; Standard Specification for Rubber Rings for Asbestos-Cement Pipe

21-27)      ASTM D2235 – 04 ; Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

21-28)      ASTM D2239 – 03 ; Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

21-29)      ASTM D2241 – 09 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)

21-30)      ASTM D2321 – 09 ; Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications ASTM D2464 – 06 Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

21-31)      ASTM D2466 – 06 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40ASTM D2467 – 06 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

21-32)      ASTM D2564 – 04(2009)e1 ; Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

21-33)      ASTM D2609 – 02(2008) ; Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

21-34)      ASTM D2657 – 07 ; Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

21-35)      ASTM D2661 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

21-36)      ASTM D2661 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

21-37)      ASTM D2665 – 09 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

21-38)      ASTM D2672 – 96a(2009) ; Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement

21-39)      ASTM D2729 – 03 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

21-40)      ASTM D2737 – 03 ; Standard Specification for Polyethylene (PE) Plastic Tubing

21-41)      ASTM D2751 – 05 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

21-42)      ASTM D2846 / D2846M – 09b ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

21-43)      ASTM D2846 / D2846M – 09b ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

21-44)      ASTM D2855 – 96(2010) ; Standard Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings

21-45)      ASTM D2949 – 01a(2008)e1 ; Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

21-46)      ASTM D3034 – 08 ; Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

21-47)      ASTM D3139 – 98(2005) ; Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

21-48)      ASTM D3212 – 07 ; Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

21-49)      ASTM F402 – 05 ; Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

21-50)      ASTM F405 – 05 ; Standard Specification for Corrugated Polyethylene (PE) Pipe and Fittings

21-51)      ASTM F409 – 02(2008) ; Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

21-52)      ASTM F437 – 09 ; Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

21-53)      ASTM F438 – 09 ; Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

21-54)      ASTM F441 / F441M – 09 ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

21-55)      ASTM F442 / F442M – 09 ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR)

21-56)      ASTM F493 – 04 ; Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

21-57)      ASTM F628 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

21-58)      ASTM F628 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

21-59)      ASTM F656 – 08 ; Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings

21-60)      ASTM F891 – 09 ; Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core

21-61)      BDS 1111:1984 ; Centrifugally Cast (spun) Iron Pressure Pipes for Water, Gas and Sewage;

21-62)      BDS 1162 : 2006 (1st revision) ; Ceramic wash basin and pedestal, ceramic wash basin and pedestals dimension, design & construction, type, permissible deviation

21-63)      BDS 1163 : 1987 ; Specification for Vitreous Sanitary Appliances,

21-64)      BDS 1356:1992 ; Specification for Ferrules for Water Services;

21-65)      BDS 1357: 1992 ; Specification for Washers with Fittings for Water Service;

21-66)      BDS 1361 : 1992 ; Faucets

21-67)      BDS 1361:1992 ; Faucets

21-68)      BDS 1507 : 1995 ; Bib taps used in water supply

21-69)      BDS 1508 : 1995 ; Stop taps used in water supply.Specifies the requirements, dimensions construction, materials and test methods of stop taps used in water supply.

21-70)      BDS 1508:1995 ; Stop taps used in water supply.

21-71)      BDS 1509:1995 ; Pillar taps used in water supply

21-72)      BDS 1562:1997 ; Solvent cements for polyvinyl chloride (PVC) plastic pipe and fitting.

21-73)      BDS 1593 : 1998 ; Plastic sanitary squatting pan

21-74)      BDS 1593:1998 ; Plastic sanitary squatting pan

21-75)      BDS 428:1964 ; Specification for Asbestos Cement Pressure Pipe;

21-76)      BDS 429:1964 ; Specification for Asbestos Cement Building and Sanitary Pipes (under revision);

21-77)      BDS 987 : 1981 ; Sand cast brass screw‐down bib taps and stop taps for water services.

21-78)      BDS EN 1112: 2009 ; Sanitary tapware ‐ Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 – General technical specification

21-79)      BDS EN 1113: 2009 ; Sanitary tapware – Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 – General technical specification

21-80)      BDS EN 1254‐2: 2009 ; Copper and copper alloys ‐ Plumbing fittings – Part 2: Fittings with compression ends for use with copper tubes

21-81)      BDS EN 14506: 2009 ; Devices to prevent pollution by backflow of potable water – Automatic diverter – Family H, type C

21-82)      BDS EN 1717: 2009 ; Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow

21-83)      BDS EN 200: 2009 ; Sanitary tapware — Single taps and combination taps for water supply systems of type 1 and type 2 — General technical specification

21-84)      BDS EN 246: 2009 ; Sanitary tapware – General specifications for flow rate regulators

21-85)      BDS EN 248: 2009 ; Sanitary tapware – General specification for electrodeposited coatings of Ni‐Cr

21-86)      BDS EN 681-1: 2008 ; Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber

21-87)      BDS EN 681-2 : 2008 ; Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers

21-88)      BDS ISO /TR 4191: 2008 ; Unplasticized polyvinyl chloride (PVC-U) pipes for water supply-Recommended practice for laying

21-89)      BDS ISO 11413:2010 ; Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting BDS ISO 11414, Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

21-90)      BDS ISO 1167-1 : 2008 ; Thermoplastics pipes fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure- Part 1: General method

21-91)      BDS ISO 1167-2 : 2008 ; Thermoplastics pipes fittings and assemblies for the conveyance of fluids- Determination of the resistance to internal pressure-

21-92)      BDS ISO 12176-2:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion

21-93)      BDS ISO 12176-3:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 3: Operator’s badge

21-94)      BDS ISO 12176-4:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4: Traceability coding

21-95)      BDS ISO 13479:2010 ; Polyolefin pipes for the conveyance of fluids — Determination of

21-96)      BDS ISO 13761:2010 ; Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 °C

21-97)      BDS ISO 13951:2010 ; Plastics piping systems — Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading

21-98)      BDS ISO 13953:2010 ; Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint

21-99)      BDS ISO 13954:2010 ; Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

21-100)    BDS ISO 13955:2010 ; Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies

21-101)    BDS ISO 13957:2010 ; Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance

21-102)    BDS ISO 14236:2010 ; Plastics pipes and fittings — Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems

21-103)    BDS ISO 161-1 : 2008 ; Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and Nominal Pressures- Part 1: Metric series

21-104)    BDS ISO 161-2 : 2008 ; Thermoplastics pipes for the conveyance of fluids- Nominal outside diameters and Nominal Pressures- Part 2: Inch – based series

21-105)    BDS ISO 1746 : 2008 ; Rubber or Plastics hoses and tubing-Bending tests

21-106)    BDS ISO 18553:2010 ; Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds

21-107)    BDS ISO 18553:2010 ; Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds Amendment 1:2010

21-108)    BDS ISO 2505 : 2008 ; Thermoplastics pipes- Longitudinal reversion – Test method and parameters

21-109)    BDS ISO 2507-2 : 2008 ; Thermoplastics pipes and fittings – Vicat softening temperature- Part 2: Test conditions for Unplasticized poly (Vinyl chloride) (PVC-U) or chlorinated poly (Vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (Vinyl chloride) (PVC-HI) pipes

21-110)     BDS ISO 265-1 : 2008 ; Pipes and fittings of plastics materials- fittings for domestic and industrial waste pipes- Basic dimensions: Metric series- Part 1: Unplasticized Poly (Vinyl chloride) (PVC-U)

21-111)     BDS ISO 3114: 2008 ; Unplasticized polyvinyl chloride (PVC) pipes for potable water supply-Extractability of lead and tin- Test method

21-112)     BDS ISO 3126 : 2008 ; Plastics piping systems-Plastics components- Determination of dimensions

21-113)     BDS ISO 3127: 2008 ; Thermoplastics pipes- Determination of resistance to external blows-Round – the – clock method

21-114)     BDS ISO 3419: 2008 ; Non – alloy and alloy steel butt–welding fittings

21-115)     BDS ISO 3458:2010 ; Assembled joints between fittings and polyethylene (PE)

21-116)     BDS ISO 3459:2010 ; Polyethylene (PE) pressure pipes — Joints assembled with mechanical fittings — Internal under pressure test method and requirement

21-117)     BDS ISO 3501:2010 ; Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of resistance to pull-out

21-118)     BDS ISO 3503:2010 ; Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of leakproofness under internal pressure when subjected to bending

21-119)     BDS ISO 3633: 2008 ; Plastics piping systems for soil and waste discharge (Low and high temperature ) inside buildings- Specifications

21-120)    BDS ISO 3822-‐1: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 1: Method of measurement

21-121)    BDS ISO 3822-‐2: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 2: Mounting and operating conditions for draw‐off taps and mixing valves

21-122)    BDS ISO 3822-‐4: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 4: Mounting and operating conditions for special appliances

21-123)    BDS ISO 4065: 2008 ; Thermoplastics pipes- Universal wall thickness table

21-124)    BDS ISO 4422-1: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC-U) for water supply – Specifications – Part 1: General

21-125)    BDS ISO 4422-2: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC-U) for water supply – Specifications – Part 2: Pipes (with or without integral sockets)

21-126)    BDS ISO 4422-3: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride)(PVC-U) for water supply- Specifications – Part 3: Fittings and joints

21-127)    BDS ISO 4422-4: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC-U) for water supply- Specifications- Part 4: Valves and ancillary equipment

21-128)    BDS ISO 4422-5: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC- U) for water supply- Specifications- Part 5: Fitness for purpose of the system

21-129)    BDS ISO 4427-1:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General

21-130)    BDS ISO 4427-1:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General Technical corrigendum 1: 2010

21-131)    BDS ISO 4427-2:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes

21-132)    BDS ISO 4427-3:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings

21-133)    BDS ISO 4427-5:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system

21-134)    BDS ISO 4433-3: 2008 ; Thermoplastics pipes- Resistance to liquid chemicals- Classification-Part 3: Unplasticized poly (vinyl chloride) (PVC-U), high- impact poly (vinyl chloride) (PVC-HI) and chlorinated poly (vinyl chloride) (PVC –C) pipes

21-135)    BDS ISO 4435: 2008 ; Plastic piping systems for non- pressure underground drainage and sewerage- Unplasticized poly (vinyl chloride) (PVC-U)

21-136)    BDS ISO 4439: 2008 ; Unplasticized polyvinyl chloride (PVC) pipes and fittings – Determination and specification of density

21-137)    BDS ISO 5251: 2008 ; Stainless steel butt–welding fittings

21-138)    BDS ISO 6259-1: 2008 ; Thermoplastics pipes- Determination of tensile properties- Part 1: General test method

21-139)    BDS ISO 6259-2: 2008 ; Thermoplastics pipes- Determination of tensile properties- Part 2: Pipes made of unplasticized poly (vinyl chloride) (PVC-U), Chlorinated poly (vinyl chloride) (PVC-C), and high – impact poly (vinyl chloride) (PVC-HI)

21-140)    BDS ISO 6761: 2008 ; Steel tubes – Preparation of ends of tubes and fittings for welding

21-141)    BDS ISO 6964:2010 ; Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method and basic specification

21-142)    BDS ISO 6992: 2008 ; Unplasticized polyvinyl chloride (PVC-U) pipes for drinking water supply – Extractability of cadmium and mercury occurring as impurities

21-143)    BDS ISO 9624:2010 ; Thermoplastics pipes for fluids under pressure — Mating dimensions of flange adapters and loose backing flanges

21-144)    BS 1010 ; Specification for Draw-Off Taps and Stopvalves for Water Services;

21-145)    BS 1125: 1987 ; Specification for WC Flushing Cisterns (Including Dual Flash Cisterns and Flush Pipes);

21-146)    BS 1212 3 (Parts) ; Specification for Float Operated Valves (excluding floats);

21-147)    BS 1244 ; Metal Sink for Domestic Purposes;

21-148)    BS 1254:1981 ; Specification for C Seats (Plastics);

21-149)    BS 1329:1974 ; Specification for Metal Hand Rinse Basins;

21-150)    BS 1415 ( 2 parts) ; Mixing Valves (Manullay Operated);

21-151)    BS 1876: 1992(1977) ; Specification for Automatic Flushing Cistern for Urinals

21-152)    BS 1968 ; Specification for Floats for Ball Valves (copper);

21-153)    BS 2456: 1973 ; Specification for Floats for Ball Valves (plastic) for Cold and Hot Water

21-154)    BS 3377:1985 ; Specification for Boilers for Use with Domestic Solid Mineral Fuel Appliances;

21-155)    BS 5163: 1986 ; Specification for Predominantly Key-Operated Cast Iron Wedge Gate Valve for Water Works;

21-156)    BS 5433: 1976 ; Specification for Underground Stop valves for Water Services (copper);

21-157)    BS 843: 1976 ; Specification for Thermal Storage Electric Water Heaters;

21-158)    BS 855:1976 ; Specification for Welded Steel Boilers for Central Heating and Indirect Hot Water Supply.

21-159)    IS 404 (Part-I)-1993 ; Specification for Lead Pipes Part I for other than Chemical Purpose (third Revision);

21-160)    ISO 160: 1980 ; Asbestos-Cement Pressure Pipes and Joints;

21-161)    ISO 2531-1991 ; Ductile Iron Pipes, Fittings and Accessories for Pressure Pipelines;

21-162)    ISO 392:1986 ; Asbestos-Cement Pipe Fittings for Building and Sanitary Purposes;

21-163)    ISO 881:1980 ; Asbestos-Cement Pipes, Joints and Fittings for Sewerage and Drainage;

 

 

 

 

 

 

20. PAINTS AND VARNISHES

건설자재 시험 및 인증 관련 규격목록 20

20. PAINTS AND VARNISHES

20-1)        BDS 1005:1981 ; Specification for Ready Mixed Paint, Brushing, Finishing, Stoving, Enamel, Colour as Required;

20-2)        BDS 1064:1983 ; Specification for Varnish, Stoving;

20-3)        BDS 1065:1983 ; Specification for Varnish, Acid Resisting;

20-4)        BDS 1066:1983 ; Specification for Varnish, Finishing, Interior;

20-5)        BDS 1097:1984 ; Specification for Plastic Emulsion Paint.

20-6)        BDS 1141:1986 ; Specification for Ready Mixed Aluminium Priming Paints for Woodwork;

20-7)        BDS 1151:1986 ; Specification for Pavement Marking Paints.

20-8)        BDS 13:1960 ; Specification for Ready Mixed Paints, Varnish, Lacquers and Related Products (under revision);

20-9)        BDS 14:1960 ; Specification for Black Bituminous Paint, Brushing for General Purposes (under revision);

20-10)      BDS 397:1964 ; Specification for Ready Mixed Paint, Brushing, Red Oxide Zinc Chrome, Priming (under revision);

20-11)      BDS 398:1964 ; Specification for Ready Mixed Paint, Spraying, Red Oxide Zinc Chrome, Priming (under revision);

20-12)      BDS 399:1964 ; Specification for Aluminum Paint, Spraying for General Purposes, in Dual Container (under revision);

20-13)      BDS 400:1964 ; Specification for Aluminium Paint, Brushing, for General Purposes in Dual Container (under revision);

20-14)      BDS 401:1964 ; Specification for Varnish, Finishing, Exterior, Type-I, (Synthetic) (Tentative) (under revision);

20-15)      BDS 401:1964 ; Specification for Varnish, Finishing, Exterior, Type-I, (synthetic) (under revision);

20-16)      BDS 402:1989 ; Specification for Ready Mixed Paint, Brushing, Finishing, Semigloss, for General Purposes (First Revision);

20-17)      BDS 499:1965 ; Specification for Ready Mixed Paints, Brushing, for Road Marking (white, yellow and black) (under revision);

20-18)      BDS 500:1965 ; Specification for Distemper Dry (under revision);

20-19)      BDS 616:1966 ; Specification for Enamel, Brushing, Exterior (i) Undercoating, (ii) Finishing, Colour as Required (under revision);

20-20)      BDS 617:1966 ; Specification for Enamel, Brushing, Interior (i) Undercoating, (ii) Finishing, Colour as Required (under revision);

20-21)      BDS 926:1980 ; Specification for Ready Mixed Paint, Brushing, Petrol Resisting, Air Drying, for Exterior Painting of Containers, Colour as Required;

20-22)      BDS 927:1980 ; Specification for Ready Mixed Paint, Brushing, Petrol Resisting, Air Drying, for Interior Painting of Tanks and Containers, Red Oxide (colour unspecified);

20-23)      BDS 928:1980 ; Specification for Ready Mixed Paint, Brushing, Acid Resisting, for Protection Against Acid Fumes, Colour as Required;

20-24)      BDS 973:1981 ; Specification for Specification and Methods of Test for Linseed Stand Oil for Paints and Varnishes;

20-25)      BDS 974:1981 ; Specification and Methods of Test for Raw Tung Oils for Paints and Varnishes;

20-26)      IS 101 ; Methods of sampling and test for paints, varnishes and related products:

20-27)      IS 104:1979 ; Specification for ready mixed paint, brushing, zinc chrome, priming (second revision)

20-28)      IS 109:1968 ; Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 and 631 (first revision)

20-29)      IS 11883:1986 ; Specification for ready mixed paint, brushing, red oxide, priming for metals

20-30)      IS 123:1962 ; Specification for ready mixed paint, brushing, finishing, semi-gloss, for general purposes, to Indian Standard colours No. 445, 446, 448, 449, 451 and 473; and red oxide (colour unspecified) (revised)

20-31)      IS 13183:1991 ; Specification for aluminium paints, heat resistant

20-32)      IS 13213:1991 ; Specification for polyurethane full gloss enamel (two pack)

20-33)      IS 133:1993 ; Specification for enamel, interior (a) undercoating, (b) finishing (third revision)

20-34)      IS 13607:1992 ; Specification for ready mixed paint, finishing, general purposes, synthetic

20-35)      IS 137:1965 ; Specification for ready mixed paint, brushing, matt or egg-shell flat, finishing, interior, to Indian Standard colour, as required (revised)

20-36)      IS 13871:1993 ; Specification for powder coatings

20-37)      IS 14314:1995 ; Specification for thinner general purposes for synthetic paints and varnishes

20-38)      IS 158:1981 ; Specification for ready mixed paint, brushing, bituminous, black, lead-free, acid, alkali, and heat resisting (third revision)

20-39)      IS 168:1993 ; Specification for ready mixed paint, air-drying semi-glossy/matt, for general purposes (third revision)

20-40)      IS 2074:1992 ; Specification for ready mixed paint, air drying red oxide-zinc chrome, priming (second revision)

20-41)      IS 2075:2000 ; Specification for ready mixed paint, stoving, red oxide-zinc chrome, priming (second revision)

20-42)      IS 2339:1963 ; Specification for aluminium paint for general purposes, in dual container

20-43)      IS 2932:2003 ; Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing (third revision)

20-44)      IS 2933:1975 ; Specification for enamel, exterior, (a) undercoating, (b) finishing (first revision)

20-45)      IS 324:1959 ; Specification for ordinary denatured spirit (revised)

20-46)      IS 324-1959 ; Specification for Ordinary Denatured Spirit (revised);

20-47)      IS 337:1975 ; Specification for varnish, finishing, interior (first revision)

20-48)      IS 341:1973 ; Specification for black Japan, Types A, B and C first revision)

20-49)      IS 347-1975 ; Specification for Varnish, Shellac for general purposes (First Revision);

20-50)      IS 348-1968 ; Specification for French Polish (First Revision);

20-51)      IS 3536:1999 ; Specification for ready mixed ‘paint, brushing, wood primer

20-52)      IS 3537:1966 ; Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275:”281, 352, 353, 358 to 361, 363,364,388,410,442, 444,628, 631,632,634,693,697, white andblack

20-53)      IS 3539:1966 ; Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required

20-54)      IS 3585:1966 ; Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work

20-55)      IS 3678:1966 ; Specification for ready mixed paint, thick white, for lettering

20-56)      IS 427:1965 ; Specification for distemper, dry, colour as required (revised)

20-57)      IS 428:2000 ; Specification for distemper, washable (second revision)

20-58)      IS 524:1983 ; Specification for varnish, finishing, exterior, synthetic (second revision)

20-59)      IS 525:196 ; Specification for varnish, finishing, exterior and general purposes (first revision)

20-60)      IS 533:1998 ; Specification for gum spirit of turpentine (oil of turpentine) (second revision)

20-61)      IS 5410:1992 ; Specification for cement paint, colour as required (first revision)

20-62)      IS 5411 ; Specification for plastic emulsion paint:

20-63)      IS 642:1963 ; Specification for varnish medium for aluminium paint (revised)

20-64)      IS 82:1992 ; Methods of sampling and test for thinners and solvents for paints (first revision)

20-65)      IS 8662:1993 ; Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing, for railway coaches (first revision)

20-66)      IS 9862:1981 ; Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting

19. ROOF COVERINGS

건설자재 시험 및 인증 관련 규격목록 19

19. ROOF COVERINGS

19-1)        ASTM A755 / A755M – 03(2008) ; Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Pre-painted by the Coil-Coating Process for Exterior Exposed Building Products

19-2)        ASTM B101 – 07 ; Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction

19-3)        ASTM C1029 – 09 ; Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

19-4)        ASTM C222 – 97(2008) ; Standard Specification for Asbestos-Cement Roofing Shingles

19-5)        ASTM C406 – 06e1 ; Standard Specification for Roofing Slate

19-6)        ASTM C836 / C836M – 10 ; Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

19-7)        ASTM D1227 – 95(2007) ; Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

19-8)        ASTM D1863 – 05 ; Standard Specification for Mineral Aggregate Used on Built-Up Roofs

19-9)        ASTM D2178 – 04 ; Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

19-10)      ASTM D225 – 07 ; Standard Specification for Asphalt Shingles (Organic Felt) Surfaced With Mineral Granules

19-11)      ASTM D226 / D226M – 09 ; Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

19-12)      ASTM D227 – 03 ; Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

19-13)      ASTM D2626 – 04 ; Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

19-14)      ASTM D2898 – 10 ; Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

19-15)      ASTM D312 – 00(2006) ; Standard Specification for Asphalt Used in Roofing

19-16)      ASTM D3161 – 09 ; Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

19-17)      ASTM D3747 – 79(2007) ; Standard Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

19-18)      ASTM D3909 – 97b(2004)e1 ; Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced With Mineral Granules

19-19)      ASTM D4272 – 09 ; Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop

19-20)      ASTM D4434 / D4434M – 09 ; Standard Specification for Poly(Vinyl Chloride) Sheet Roofing

19-21)      ASTM D450 – 07 ; Standard Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing

19-22)      ASTM D4601 – 04 ; Standard Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing

19-23)      ASTM D4637 – 08 ; Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane

19-24)      ASTM D4897 / D4897M – 01(2009) ; Standard Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing

19-25)      ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

19-26)      ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

19-27)      ASTM E108 – 10a ; Standard Test Methods for Fire Tests of Roof Coverings

19-28)      ASTM G154 – 06 ; Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

19-29)      ASTM G155 – 05a ; Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

19-30)      ASTM G90 – 05 ; Standard Practice for Performing Accelerated Outdoor Weathering of Nonmetallic Materials Using Concentrated Natural Sunlight

19-31)      BDS 1046:1983 ; Specification for Asbestos Cement Products – Corrugated Sheets and Fittings for Roofing and Cladding;

19-32)      BDS 1122:1985 ; Specification for Hot-dip Galvanized Steel and Coil.

19-33)      BDS 430:1964 ; Specification for Asbestos Cement Corrugated Sheets for Roofing and Cladding

19-34)      BDS 431:1964 ; Specification for Asymmetrical Section Corrugated Sheets in Asbestos Cement for Roofing and Cladding

19-35)      BDS 579:1966 ; Specification for Asbestos Cement Flat Sheets (under revision);

19-36)      BDS 868:1978 ; Code of Practice for Galvanized Corrugated Sheet Roof and Wall Coverings;

19-37)      BDS EN 1024: 2008 ; Clay roofing tiles for discontinuous laying — Determination of geometric characteristics

19-38)      BDS EN 1304: 2008 ; Clay roofing tiles and fittings — Product definitions and specifications

19-39)      BDS EN 490: 2008 ; Concrete roofing tiles and fittings for roof covering and all cladding — Product specifications

19-40)      BDS EN 49l: 2008 ; Concrete roofing tiles and fittings for roof covering and wall cladding — Test methods

19-41)      BDS EN 538: 2008 ; Clay roofing tiles for discontinuous laying — Flexural strength test

19-42)      BDS EN 539-l: 2008 ; Clay roofing tiles for discontinuous laying Determination of physical characteristics — Part 1: Impermeability test

18. BUILDERS HARDWARE 건설자재 시험 및 인증 관련 규격목록 18

건설자재 시험 및 인증 관련 규격목록 18

18. BUILDERS HARDWARE

18-1)        BDS 113:1986 ; Specification for Latches and Locks for Doors in Buildings;

18-2)        IS 10019-1981 ; Specification for Steel Window Stays and Fasteners;

18-3)        IS 10090-1982 ; Specification for Numericals;

18-4)        IS 1019-1974 ; Specification for Rim Latches (Second Revision);

18-5)        IS 10342-1982 ; Specification for Curtain Rail System

18-6)        IS 12817:1997 ; Specification for stainless steel butt hinges (first revision)

18-7)        IS 12867:1989 ; Specification for PVC hand rails covers

18-8)        IS 1341-1992 ; Specification for Steel Butt Hinges (Sixth Revision);

18-9)        IS 14912:2001 ; Specification for door closers concealed type (hydraulically regulated)

18-10)      IS 1823-1980 ; Specification for Floor Door Stoppers (Third Revision);

18-11)      IS 1837-1966 ; Specification for Fanlight Pivots (First Revision);

18-12)      IS 204-1991/1992 ; Specification for Tower Bolts;

18-13)      IS 205-1992 ; Specification for Nonferrous Metal Butt Hinges (fourth Revision);

18-14)      IS 206-1992 ; Specification for Tee and Strap Hinges (Fourth Revision);

18-15)      IS 208-1996 ; Specification for Door Handles (Fifth Revision);

18-16)      IS 2209-1976 ; Specification for Mortice Locks (vertical type) (Third Revision);

18-17)      IS 2681-1993 ; Specification for Nonferrous Metal Sliding Door Bolts for Use with Padlocks (Third Revision);

18-18)      IS 281-1991 ; Specification for Mild Steel Sliding Door Bolts for Use with Padlock (Third Revision);

18-19)      IS 3564-1995 ; Specification for Door Closers (hydraulically regulated) (Second Revision);

18-20)      IS 362-1991 ; Specification for Parliament Hinges (Fifth Revision);

18-21)      IS 363-1993 ; Specification for Hasps and Staples (Fourth Revision);

18-22)      IS 364-1993 ; Specification for Fanlight Catch (Third Revision);

18-23)      IS 3818-1992 ; Specification for Continuous (piano) Hinges (Third Revision);

18-24)      IS 3828-1966 ; Specification for Ventilator Chains;

18-25)      IS 3843-1995 ; Specification for Steel Backflap Hinges; (First Revision)

18-26)      IS 3847-1992 ; Specification for Mortice Night Latches; (First Revision)

18-27)      IS 452-1973 ; Specification for Door Springs, Rat-tail Type (Second Revision);

18-28)      IS 453-1993 ; Specification for Double Acting Spring Hinges (Third Revision);

18-29)      IS 4621-1975 ; Specification for Indicating Bolts for use in Public Baths and Lavatories (First Revision);

18-30)      IS 4948-2002 ; Specification for Welded Steel Wire Fabric for General Use (Second Revision);

18-31)      IS 4992-1975 ; Specification for Door Handles for Mortice Locks (vertical type) (First Revision);

18-32)      IS 5187-1972 ; Specification for Flush Bolts (First Revision);

18-33)      IS 5899-1970 ; Specification for Bathroom Latches;

18-34)      IS 5930-1970 ; Specification for Mortice Latch (vertical type);

18-35)      IS 6315-1971 ; Specification for Floor Springs (hydraulically regulated) for Heavy Doors;

18-36)      IS 6318-1971 ; Specification for Plastic Window Stays and Fasteners;

18-37)      IS 6343-1982 ; Specification for Door Closers (pneumatically regulated) for Light Doors Weighing up to 40 kg (First Revision);

18-38)      IS 6602-1972 ; Specification for Ventilator Poles;

18-39)      IS 6607-1972 ; Specification for Rebated Mortice Locks (vertical type);

18-40)      IS 7196-1974 ; Specification for Hold Fast;

18-41)      IS 7197-1974 ; Specification for Double Action Floor Springs (without oil check) for Heavy Doors;

18-42)      IS 729-1979 ; Specification for Drawer Locks, Cupboard Locks and Box Locks (Third Revision);

18-43)      IS 7534-1985 ; Specification for sliding locking bolts for use with padlocks (first revision);

18-44)      IS 7540-1974 ; Specification for Mortice Dead Locks;

18-45)      IS 8756-1978 ; Specification for Ball Catches for use in Wooden Almirah;

18-46)      IS 8760-1978 ; Specification for Mortice Sliding Door Locks, with Lever Mechanism;

18-47)      IS 9106-1979 ; Specification for Rising Butt Hinges;

18-48)      IS 9131-1979 ; Specification for Rim Locks;

18-49)      IS 9460-1980 ; Specification Flush Drop Handle for Drawer;

18-50)      IS 9899-1981 ; Specification for Hat, Coat and Wardrobe Hooks;

 

17. ALUMINIUM AND ALUMINIUM ALLOYS

건설자재 시험 및 인증 관련 규격목록 17

17. ALUMINIUM AND ALUMINIUM ALLOYS

17-1)        ASTM B108 / B108M – 08 ; Standard Specification for Aluminum-Alloy Permanent Mold Castings

17-2)        ASTM B209 – 07 ; Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

17-3)        ASTM B210 – 04 ; Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

17-4)        ASTM B211 – 03 ; Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire

17-5)        ASTM B221 – 08 ; Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

17-6)        ASTM B241 / B241M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

17-7)        ASTM B26 / B26M – 09 ; Standard Specification for Aluminum-Alloy Sand Castings

17-8)        ASTM B308 / B308M – 02 ; Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles

17-9)        ASTM B313 / B313M – 09 ; Standard Specification for Aluminum and Aluminum-Alloy Round Welded Tubes

17-10)      ASTM B316 / B316M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods

17-11)      ASTM B429 / B429M – 06 ; Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube

17-12)      ASTM B483 / B483M – 03 ; Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applications

17-13)      ASTM B547 / B547M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round Tube

17-14)      ASTM B632 / B632M – 08 ; Standard Specification for Aluminum-Alloy Rolled Tread Plate

17-15)      ASTM B745 / B745M – 97(2005) ; Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

17-16)      ASTM B85 / B85M – 09 ; Standard Specification for Aluminum-Alloy Die Castings

17-17)      ASTM E34 – 94(2002) ; Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys

17-18)      BDS EN 12020-1:2010 ; Aluminium and aluminium alloys— Extruded precision profiles in alloys EN AW-6060 and EN AW-6063— Part 1: Technical conditions for inspection and delivery

17-19)      BDS EN 12020-2:2010 ; Aluminium and aluminium alloys — Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 — Part 2: Tolerances on dimensions and form

17-20)      BDS EN 515:2010 ; Aluminium and aluminium alloys — Wrought products — Temper designations

17-21)      BDS EN 755-1:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 1: Technical conditions for inspection and delivery

17-22)      BDS EN 755-2:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: Mechanical properties

17-23)      BDS EN 755-3:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 3: Round bars, tolerances on dimensions and form

17-24)      BDS EN 755-4:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 4: Square bars, tolerances on dimensions and form

17-25)      BDS EN 755-5:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 5: Rectangular bars, tolerances on dimensions and form

17-26)      BDS EN 755-6:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 6: Hexagonal bars, tolerances on dimensions and

17-27)      BDS EN 755-7:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 7: Seamless tubes, tolerances on dimensions and form

17-28)      BDS EN 755-8:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 8: Porthole tubes, tolerances on dimensions and form

17-29)     BDS EN 755-9:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 9: Profiles, tolerances on dimensions and form