Archive for year: 2014

Synthetic turf

27 Dec 2014 Comments
Off

Product : Synthetic turf 

아래는 UFGS 관련 인조잔디에 대한 적합성 시험항목입니다.

1. Yarn Number Based on Short-Length Specimens ASTM D1059-01

2. Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (CRE Testing Machine) ASTM D2261-11

3. Identification of Fibers in Textiles ASTM D276-00a (2008)

4. Tuft Bind of Pile Yarn Floor Coverings ASTM D1335-12

5. Tensile Properties of Yarns by the Single-Strand Method . Option A (Straight) ASTM D2256/D2256M-10

6. Ignition Characteristics of Finished Textile Floor Covering Materials ASTM D2859-06

7. Water Permeability of Geotextiles by Permittivity ASTM D4491 – 99a (2014)e1

8. Breaking Strength and Elongation of Textile Fabrics (Grab Test) ASTM D5034-09 (2013)

9. Binding Sites per Unit Length or Width of Pile Yarn Floor Coverings ASTM D5793-05

10. Tuft Height of Pile Floor Coverings ASTM D5823-05a11

11. Mass Per Unit Area of Pile Yarn Floor Coverings – Total Mass per Unit Area ASTM D5848-10e1 Section 7

12. Mass Per Unit Area of Pile Yarn Floor Coverings – Component Masses per Unit Area ASTM D5848-10e1 Section 8

13. Mass Per Unit Area of Pile Yarn Floor Coverings – Pile Yarn Mass per Unit Area ASTM D5848-10e1 Section 9

14. Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source ASTM E 648-10e¹

15. Melting and Crystallization Temperature by Thermal Analysis ASTM E794-06 (2012)

16. Relative Abrasiveness of Synthetic Turf Playing Surfaces ASTM F1015-03 (2009)

 

Turkmenistan Certificate TDS

05 Dec 2014 Comments
Off

Turkmenistan Certificate TDS 인증서

TDS2

- 투르크메니스탄은 자국 내로 수입되는 제품에 대해  제품인증의 취득을 요구하고 있습니다. 특히측정에 사용되는 계측장비는 “Turkmenstandartlary.”의 관련 규정에 따라 교정되어야 합니다. 1998 년경, 투르크메니스탄으로 수입되는 식품류에 대해 위생관련 인증요구 사항이 발효되었습니다. 국가 위생 및 역학 검사기관(SSEI)이 적합성인증서를 발행하기 위한 시험을 수행하며 이러한 식품류에는 필수적으로 러시아 언어로 표기된 제품설명서를 부착하여야 합니다.

 

 

투르크메니스탄의 state system of certifcation의 인증조직구조 :

TDS1

  • The State agency for Certification of products and services
    (Glavgosinspektsiya Turkmenistan);
  • Bodies for certification of products and services;
  • Testing laboratories (centers)

 

 

 

 

강제인증 대상 :

  • 국가 표준 및 기타 문서에 따라 안전 및 보건, 품질 및 환경관련 주요 품목은 해당 규격 및 법규  TDS 1.2 에서 품목의  적함함을 보장토록 요구하는 모든  대상물품, 작업 및 서비스 품목을 강제 인증대상으로 규정하고 관리함.[ HS code  분류 목록의 최신 개정을 확인할 필요 있음. 문의바로가기  ]
  • 관련 규정에 의해 인증을 취득한 제품관련 정보는 State Certification Registry에 등록하고 제품에는 해당 마크를 부착하여야 함.

참고 :

  • 일상적 통관절차는 예상보다 다소 늦게 진행되며 엄격한 법적용 등으로 인해 관료적이라는 평판이 있음.
  • 품목의 가격타당성은 최고 상공 회의에 의해 참조되고 모든 품목은 수입전에 관련기관에 필수적으로 등록되어야 하며 이러한 절차를 처음 경험하는 경우 상당한 어려움이 있을 수 있음. [BIRJA etc.]
  • 물품의 수출 수입에 관련하여 State Commodity and Raw Materials Exchange (SCRME) : [물품 및 원자재 거래소]에 등록하여야 함.
  • 일부 투자  또는 Civil construction 의 경우, Ministry of Economy and Development에 의한 승인이 요구될 수 있음.
  • 상사 분쟁의 경우, Turkmenistan은 2012년 현재까지 New York Convention on International Arbitration에 가입하지 않아 상사간 분쟁을  중재할 조직이 없음.

 

 

ASTM D6878 – on TPO membrane Analysis

건축자재 인증 및 시험 관련 규격

Download : Analysis of one TPO membrane per ASTM D6878_D6878M-13

Analysis of one TPO membrane per ASTM D6878/D6878M-13.

아래는 적용되는 분석기법입니다.

    1. ASTM D 6878/D : Brittleness Point per ASTM D2137, Method B
    2. ASTM D 6878/D : Ozone Resistance per ASTM D 1149 (Exposed to 100 mPa ozone in air @40°C, wrapped around a 3″ mandrel for 166 hrs exposure) – OUTSOURCED
    3. ASTM D 6878/D : Breaking Strength per ASTM D751, grab method – MD
    4. ASTM D 6878/D : Breaking Strength per ASTM D751, grab method – XMD
    5. ASTM D 6878/D : Elongation at Reinforcement Break per ASTM D751, grab method – MD
    6. ASTM D 6878/D : Elongation at Reinforcement Break per ASTM D751, grab method – XMD
    7. ASTM D 6878/D : Factory Seam Strength @ 2 in/min (12 in x 1 in specimen) per ASTM D751,grab method
    8. ASTM D 6878/D : Heat Aging, 5376 hrs (224 days) @ 116°C, per ASTM D573
    9. ASTM D 6878/D : Linear Dimensional Change, 6 hr @ 70°C (158°F), per ASTM D1204
    10. ASTM D 6878/D : Post Heat Aging: Breaking Strength per ASTM D751, grab method – MD
    11. ASTM D 6878/D : Post Heat Aging: Breaking Strength per ASTM D751, grab method – XMD
    12. ASTM D 6878/D : Post Heat Aging: Elongation at Reinforcement Break per ASTM D751, grab method – MD
    13. ASTM D 6878/D : Post Heat Aging: Elongation at Reinforcement Break per ASTM D751, grab method – XMD
    14. ASTM D 6878/D : Post Heat Aging: Tearing Strength, 2 in/min (8 in x 8 in specimen) per ASTMD751 – MD
    15. ASTM D 6878/D : Post Heat Aging: Tearing Strength, 2 in/min (8 in x 8 in specimen) per ASTMD751 – XMD
    16. ASTM D 6878/D : Post Heat Aging: Weight Change (mass)
    17. ASTM D 6878/D : Tearing Strength, 2 in/min (8 in x 8 in specimen), per ASTM D751 – MD
    18. ASTM D 6878/D : Tearing Strength, 2 in/min (8 in x 8 in specimen), per ASTM D751 – XMD
    19. ASTM D 6878/D : Thickness, Coating Over Fabric or Scrim (weathering side only) per ASTM D7635
    20. ASTM D 6878/D : Thickness, Sheet-Overall per ASTM D751
    21. ASTM D 6878/D : Water Absorption, 166 hrs @ 70°C (158°F) (mass) per ASTM D471 – Performed on top coating material ONLY
    22. ASTM D 6878/D : Weather Resistance per ASTM G 155 at 0.35 W/(m²•nm) at 340 nm (8000 hrs)

22. MISCELLANEOUS MATERIALS

건설자재 시험 및 인증 관련 규격목록 22

22. MISCELLANEOUS MATERIALS

22-1)        ANSI A108.10-2009 ; Installation of Grout in Tilework;

22-2)        ANSI A108.1-2009 ; Specification for the Installation of Ceramic Tile with Portland Cement Mortar;

22-3)        ANSI A108.4-2009 ; Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile Setting Epoxy Adhesive;

22-4)        ANSI A108.5-2009 ; Installation of Ceramic Tile with Dry-Set Portland Cement Mortar or Latex-Portland Cement Mortar;

22-5)        ANSI A108.6-2009 ; Installation of Ceramic Tile with Chemical Resistant, Water Cleanable Tile Setting and Grouting Epoxy;

22-6)        ANSI A108.7-2009 ; Specification for Electrically Conductive Ceramic Tile Installed with Conductive Dry-Set Portland Cement Mortar;

22-7)        ANSI A108.8-2009 ; Installation of Ceramic Tile with Chemical Resistant Furan Mortar and Grout;

22-8)        ANSI A108.9-2009 ; Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout;

22-9)        ANSI A118.1-2009 ; Specification for Dry-Set Portland Cement Mortar;

22-10)      ANSI A118.2-2009 ; Specifications for Conductive Dry-set Portland Cement Mortar;

22-11)      ANSI A118.3-2009 ; Specifications for Chemical Resistant Water Cleanable Tile Setting and Grouting Epoxy and Water Cleanable Tile Setting Epoxy Adhesive;

22-12)      ANSI A118.4-2009 ; Specifications Furan Latex – Portland Cement Mortar;

22-13)      ANSI A118.5-2009 ; Specifications for Chemical Resistant Furan;

22-14)      ANSI A118.6-2009 ; Specifications for Ceramic Tile Grouts;

22-15)      ANSI A118.8-2009 ; Specifications for Modified Epoxy Emulsion Mortar/Grout;

22-16)      ANSI A136.1-2009 ; Organic Adhesives for Installation of Ceramic Tile;

22-17)      ANSI A137.1-2008 ; Specification for Ceramic Tile;

22-18)      ANSI A137.1-2008 ; Specifications for Ceramic Tile;

22-19)      ANSI Z 97.1-2009 ; Safety Performance Specifications and Methods of Tests for Transport Safety Glazing Materials Used in Building;

22-20)      ASTM A116 – 05 ASTM A121 – 07 ; Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

22-21)      ASTM A121 – 07 ; Standard Specification for Metallic-Coated Carbon Steel Barbed Wire

22-22)      ASTM A368 – 95a(2009) ; Standard Specification for Stainless Steel Wire Strand

22-23)      ASTM A392 – 07 ; Standard Specification for Zinc-Coated Steel Chain-Link Fence Fabric

22-24)      ASTM A475 – 03(2009)e1 ; Standard Specification for Zinc-Coated Steel Wire Strand

22-25)      ASTM A492 – 95(2009) ; Standard Specification for Stainless Steel Rope Wire

22-26)      ASTM A510 – 08 ; Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

22-27)      ASTM A586 – 04a(2009)e1 ; Standard Specification for Zinc-Coated Parallel and Helical Steel Wire Structural Strand

22-28)      ASTM A603 – 98(2009)e1 ; Standard Specification for Zinc-Coated Steel Structural Wire Rope

22-29)      ASTM A817 – 07 ; Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire

22-30)      ASTM A824 – 01(2007) ; Standard Specification for Metallic-Coated Steel Marcelled Tension Wire for Use With Chain Link Fence

22-31)      ASTM C1014 – 08 ; Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation

22-32)      ASTM C1029 – 09 ; Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

22-33)      ASTM C1036 – 06 ; Standard Specification for Flat Glass

22-34)      ASTM C1048 – 04 ; Standard Specification for Heat-Treated Flat Glass—Kind HS, Kind FT Coated and Uncoated Glass

22-35)      ASTM C1071 – 05e1 ; Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material)

22-36)      ASTM C1193 – 09 ; Standard Guide for Use of Joint Sealants

22-37)      ASTM C1193 – 09 ; Standard Guide for Use of Joint Sealants

22-38)      ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

22-39)      ASTM C126 – 09 ; Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units

22-40)      ASTM C1363 – 05 ; Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus

22-41)      ASTM C167 – 09 ; Standard Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations

22-42)      ASTM C177 – 04 ; Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

22-43)      ASTM C195 – 07 ; Standard Specification for Mineral Fiber Thermal Insulating Cement

22-44)      ASTM C196 – 00(2005) ; Standard Specification for Expanded or Exfoliated Vermiculite Thermal Insulating Cement

22-45)      ASTM C208 – 08a ; Standard Specification for Cellulosic Fiber Insulating Board

22-46)      ASTM C209 – 07ae1 ; Standard Test Methods for Cellulosic Fiber Insulating Board

22-47)      ASTM C240 – 08e1 ; Standard Test Methods of Testing Cellular Glass Insulation Block

22-48)      ASTM C335 – 05ae1 ; Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation

22-49)      ASTM C411 – 05 ; Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation

22-50)      ASTM C449 – 07 ; Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement

22-51)      ASTM C509 – 06 ; Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material

22-52)      ASTM C516 – 08 ; Standard Specification for Vermiculite Loose Fill Thermal Insulation

22-53)      ASTM C518 – 04 ; Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

22-54)      ASTM C520 – 04 ; Standard Test Methods for Density of Granular Loose Fill Insulations

22-55)      ASTM C533 – 09 ; Standard Specification for Calcium Silicate Block and Pipe Thermal Insulation

22-56)      ASTM C534 / C534M – 08 ; Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form

22-57)      ASTM C542 – 05 ; Standard Specification for Lock-Strip Gaskets

22-58)      ASTM C547 – 07e1 ; Standard Specification for Mineral Fiber Pipe Insulation

22-59)      ASTM C549 – 06 ; Standard Specification for Perlite Loose Fill Insulation

22-60)      ASTM C552 – 07 ; Standard Specification for Cellular Glass Thermal Insulation

22-61)      ASTM C553 – 08 ; Standard Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications

22-62)      ASTM C564 – 09a ; Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

22-63)      ASTM C578 – 09e1 ; Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

22-64)      ASTM C591 – 09 ; Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation

22-65)      ASTM C592 – 08a ; Standard Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type)

22-66)      ASTM C610 – 09e1 ; Standard Specification for Molded Expanded Perlite Block and Pipe Thermal Insulation

22-67)      ASTM C612 – 09 ; Standard Specification for Mineral Fiber Block and Board Thermal Insulation

22-68)      ASTM C665 – 06 ; Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing

22-69)      ASTM C716 – 06 ; Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials

22-70)      ASTM C719 – 93(2005) ; Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)

22-71)      ASTM C726 – 05e1 ; Standard Specification for Mineral Fiber Roof Insulation Board

22-72)      ASTM C728 – 05(2010) ; Standard Specification for Perlite Thermal Insulation Board

22-73)      ASTM C739 – 08 ; Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

22-74)      ASTM C764 – 07 ; Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation

22-75)      ASTM C794 – 06 ; Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants

22-76)      ASTM C834 – 10 ; Standard Specification for Latex Sealants

22-77)      ASTM C864 – 05 ; Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers

22-78)      ASTM C916 – 85(2007) ; Standard Specification for Adhesives for Duct Thermal Insulation

22-79)      ASTM C919 – 08 ; Standard Practice for Use of Sealants in Acoustical Applications

22-80)      ASTM C920 – 08 ; Standard Specification for Elastomeric Joint Sealants

22-81)      ASTM C991 – 08e1 ; Standard Specification for Flexible Fibrous Glass Insulation for Metal Buildings

22-82)      ASTM D1003 – 07e1 ; Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics

22-83)      ASTM D1044 – 08 ; Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion

22-84)      ASTM D1204 – 08 ; Standard Test Method for Linear Dimensional Changes of Nonrigid

22-85)      ASTM D1327 – 04 ; Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing

22-86)      ASTM D146 – 04 ; Standard Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing

22-87)      ASTM D1593 – 09 ; Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting

22-88)      ASTM D1668 – 97a(2006) ; Standard Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing

22-89)      ASTM D173 – 03 ; Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing

22-90)      ASTM D2103 – 08 ; Standard Specification for Polyethylene Film and Sheeting

22-91)      ASTM D2126 – 09 ; Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

22-92)      ASTM D2178 – 04 ; Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

22-93)      ASTM D226 / D226M – 09 ; Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

22-94)      ASTM D227 – 03 ; Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

22-95)      ASTM D25 – 99(2005) ; Standard Specification for Round Timber Piles

22-96)      ASTM D2626 – 04 ; Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

22-97)      ASTM D2628 – 91(2005) ; Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements

22-98)      ASTM D2842 – 06 ; Standard Test Method for Water Absorption of Rigid Cellular Plastics

22-99)      ASTM D2843 – 10 ; Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics

22-100)    ASTM D3294 – 09 ; Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes

22-101)    ASTM D3406 – 95(2006) ; Standard Specification for Joint Sealant, Hot-Applied, Elastomeric-Type, for Portland Cement Concrete Pavements

22-102)    ASTM D3468 – 99(2006)e1 ; Standard Specification for Liquid-Applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing

22-103)    ASTM D3667 – 05 ; Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors

22-104)    ASTM D3678 – 97(2008)e1 ; Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions

22-105)    ASTM D3679 – 09a ; Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding

22-106)    ASTM D3771 – 03(2007) ; Standard Specification for Rubber Seals Used in Concentrating Solar Collectors

22-107)    ASTM D3832 – 79(2006) ; Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems

22-108)    ASTM D3841 – 97(2008)e1 ; Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels

22-109)    ASTM D41 – 05 ; Standard Specification for Asphalt Primer Used in Roofing, Damp proofing, and Waterproofing

22-110)     ASTM D43 – 00(2006) ; Standard Specification for Coal Tar Primer Used in Roofing, Damp proofing, and Waterproofing

22-111)     ASTM D449 – 03(2008) ; Standard Specification for Asphalt Used in Damp proofing and Waterproofing

22-112)     ASTM D450 – 07 ; Standard Specification for Coal-Tar Pitch Used in Roofing, Damp proofing, and Waterproofing

22-113)     ASTM D4802 – 02 ; Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet

22-114)     ASTM D543 – 06 ; Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

22-115)     ASTM D635 – 06 ; Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

22-116)     ASTM D638 – 08 ; Standard Test Method for Tensile Properties of Plastics

22-117)     ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

22-118)     ASTM D6690 – 07 ; Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

22-119)     ASTM D695 – 08 ; Standard Test Method for Compressive Properties of Rigid Plastics

22-120)    ASTM D882 – 09 ; Standard Test Method for Tensile Properties of Thin Plastic Sheeting

22-121)    ASTM E119 – 09c ; Standard Test Methods for Fire Tests of Building Construction and Materials

22-122)    ASTM E84 – 10 ; Standard Test Method for Surface Burning Characteristics of Building Materials

22-123)    ASTM F1183 – 96(2006) ; Standard Specification for Aluminum Alloy Chain Link Fence Fabric

22-124)    BDS 1301 : 1990 ; Specification for Glazed Earthenware Wall Tiles;

22-125)    BDS 1301:1990 ; Specification for Glazed Earthenware Wall Tiles;

22-126)    BDS 1493:1994 ; Glossary of terms used in refractory

22-127)    BDS 1494:1994 ; Dimension of refractory bricks

22-128)    BDS 1495:1994 ; High aluminium refractory bricks

22-129)    BDS 809:1973 ; Specification for Wood Poles for Overhead Power and Telecommunication Lines;

22-130)    BDS 885:1979 ; Method for Measuring Viscosity Number and K-Value of PVC Resins;

22-131)    BDS 886:1978 ; Method for Direct Measuring the Specific Gravity of Plastics;

22-132)    BDS 887:1978 ; Method for Measuring Deformation under Heat of Flexible Rigid PVC Compounds;

22-133)    BDS 888:1978 ; Method for Measuring Temperature of Deflection under Load;

22-134)    BDS 889:1978 ; Method for Measuring the Vicat Softening Temperature (VST) of Thermoplastics;

22-135)    BDS 890:1978 ; Method for Measuring the Water Absorption at Room Temperature and Bolling Water Absorption of Plastics;

22-136)    BDS 891:1978 ; Method for Measuring the Flexural Modulus of Plastics;

22-137)    BDS 892:1978 ; Method for Measuring the Resistance to Tear Propagation of Flexible Plastics, Film or Sheeting;

22-138)    BS 6431 ; Floor and Wall Tiles;

22-139)    BS 6431 Part 1 1983 ; Specification for Classification and Making, Including Definitions and Characteristics;

22-140)    BS 6431 Part 1 to Part 23 ; Ceramic Floor and Wall Tiles.

22-141)    BS 6431 Part 10 1984 ; Method for Determination of Dimensions and Surface Quality;

22-142)    BS 6431 Part 11 1983 ; Method for Determination of Water Absorption;

22-143)    BS 6431 Part 12 1983 ; Method for Determination of Modulus of;

22-144)    BS 6431 Part 13 1986 ; Method for Determination of Scratch Hardness of Surface According to Mhos;

22-145)    BS 6431 Part 14 1983 ; Method for Determination of Resistance to Abrasion of Unglazed Tiles;

22-146)    BS 6431 Part 15 1983 ; Method for Determination of Linear Thermal Expansion;

22-147)    BS 6431 Part 16 1983 ; Method for Determination of Resistance to Thermal Shock;

22-148)    BS 6431 Part 17 1983 ; Method for Determination of Crazing Resistance-Glazed Tiles;

22-149)    BS 6431 Part 18 1983 ; Method for Determination of Chemical Resistance-Unglazed Tiles;

22-150)    BS 6431 Part 19 1984 ; Method for Determination of Chemical Resistance-Unglazed Tiles;

22-151)    BS 6431 Part 2 1984 ; Specification for Struded Ceramic Tiles with Low Water Absorption (E< 3%) Group A1;

22-152)    BS 6431 Part 20 1984 ; Method for Determination of Resistance to Surface Abrasion-Glazed Tiles;

22-153)    BS 6431 Part 23 1986 ; Specification for Sampling and Basis for Acceptance;

22-154)    BS 6431 Part 3 ; Extruded Ceramic Tiles with a Water Absorption of 3% < 6%. Group A 11a;

22-155)    BS 6431 Part 3 Section 3.1 1986 ; Specification for General Products;

22-156)    BS 6431 Part 3 Section 3.2 1986 ; Specification for Products Terre Cuite, Cotto, Baldosion Catalan;

22-157)    BS 6431 Part 4 ; Extruded Ceramic Tiles with a Water Absorption of 6% <E< 10%. Group A11b;

22-158)    BS 6431 Part 4 ; Section 4.2 1986

22-159)    BS 6431 Part 4 ; Specification for General Products;

22-160)   BS 6431 Part 5 1986 ; Specification for Extruded Ceramic Tiles with a Water Absorption of E>10%, Group A111;

22-161)    BS 6431 Part 6 1984 ; Specification for Dust-prestressed Ceramic Tiles with a Low-Water Absorption (E<3%)Group B1;

22-162)   BS 6431 Part 7 1986 ; Specification for Dust-prestressed Ceramic Tiles with a Water Absorption of 3% <E £ 6%. Group B11a;

22-163)   BS 6431 Part 8 1986 ; Specification for Dust-prestressed Ceramic Tiles with Water Absorption of 6% < E £ 10%. Group B11b;

22-164)    BS 6431 Part 9 1984 ; Specification for Dust-Prestressed Ceramic Tiles with a Water Absorption of E >10%. Group B111;

22-165)    IS 10102:1982 ; Technical supply conditions for Rivets.

22-166)    IS 110:1968 ; Specification for Ready Mixed Paint, Brushing, Grey Filler, for Enamels, for Use Over Primers (First Revision);

22-167)    IS 1900:1974 ; Method of Testing Wood Poles;

22-168)    IS 1902:1961 ; Code of Practice for Preservation of Bamboo and Cane for Non-structural Purposes;

22-169)    IS 1929:1982 ; Specification for Hot Forged Steel Rivets for Hot Closing (12 to 36 mm diameter) (First Revision);

22-170)    IS 2155:1982 ; Specification for Cold-Forged Solid Steel Rivets for Hot Closing (6 to 16 mm diameter) (First Revision);

22-171)    IS 2365:1977 ; Specification for Steel Wire Suspension Ropes for Lifts, Elevators and Hoists (First Revision).

22-172)    IS 2643:1975 ; Dimensions for Pipe Threads for Fastening Purposes;

22-173)    IS 2907:1964 ; Specification for Non-ferrous Rivets (1.6 mm to 10 mm)

22-174)    IS 2998:1981 ; Specification for Cold Forged Steel Rivets for Cold Closing (1 to 16 mm diameter) (First Revision);

22-175)    IS 3337:1978 ; Specification for Ballies for General Purposes (First Revision);

22-176)    IS 345:1952 ; Specification for Wood Filler, Transparent, Liquid;

22-177)    IS 3709:1966 ; Specification for Mastic Cement for Bedding of Metal Windows;

22-178)    IS 419:1967 ; Specification for Putty for Use on Window Frames (First Revision);

22-179)    IS 421:1953 ; Specification for Jointing Paste, for Bedding Moldings on Coaching Stock;

22-180)    IS 423:1961 ; Specification for Plastic Wood, for Joiners’ Filler (revised);

22-181)    IS 424:1965 ; Specification for Plastic Asphalt (revised);

22-182)    IS 554:1975 ; Dimensions for Pipe Threads where Pressure Tight Joints are Required on the Threads (Second Revision);

22-183)    IS 6711:1972 ; Code of Practice for Maintenance of Wood Poles for Overhead Power and Telecommunications Lines.

22-184)    IS 6874:1973 ; Method of Tests for Round Bamboos;

22-185)    IS 7164:1973 ; Specification for Stopper.

22-186)    IS 8242:1976 ; Methods of Tests for Split Bamboo;

22-187)    IS 8295:1976 ; Specification for Bamboo Chicks, Part I Fine;

22-188)    IS 9096:1979 ; Code of Practice for Preservation of Bamboos for Structural Purposes.

22-189)    ISO 10080:1990 ; Refractory Products-Classification of Dense, Shaped Acid-Resisting Products;

22-190)    ISO 10081:1991 ; Basic Refractory Products-Classification-Part I: Products Containing Less Than 7% Residual Carbon.

22-191)    ISO 10563:1991 ; Building Construction-Sealants for Joints-Determination of Change in Mass and Volume;

22-192)    ISO 10590:1991 ; Building Construction-Sealants-Determination of Adhesion/Cohesion Properties at Maintained Extension after Immersion in Water;

22-193)    ISO 10591 : 1991 ; Building Construction-Sealants-Determination of Adhesion/Cohesion Properties after Immersion in Water.

22-194)    ISO 1109:1975 ; Refractory Products-Classification of Dense Shaped Refractory Products;

22-195)    ISO 1146:1988 ; Pyrometric Reference Cones for Laboratory Use-Specification;

22-196)    ISO 1893:1989 ; Refractory Products-Determination of Refractoriness-Under-Load (differential with rising temperature);

22-197)    ISO 1927:1984 ; Prepared Unshaped Refractory Materials (Dense and Insulating) Classification;

22-198)    ISO 2245:1990 ; Shaped Insulating Refractory Products-Classification;

22-199)    ISO 2444 : 1988 ; Joints in Buildings-Vocabulary;

22-200)    ISO 2477:1987 ; Shaped Insulating Refractory Products-Determination of Permanent Change in Dimensions on Heating;

22-201)    ISO 2478:1987 ; Dense Shaped Refractory Products-Determination of Permanent Change in Dimensions on Heating;

22-202)    ISO 3187:1989 ; Refractory Products-Determination of Creep in Compression;

22-203)    ISO 3867:1982 ; Agglomerated Cork-Material of Expansion Joints for Construction and Building Test-Methods;

22-204)    ISO 3869:1981 ; Agglomerated Cork-Filler Material of Expansion Joints for Construction and Buildings -Characteristics, Sampling and Packing;

22-205)    ISO 3934:1978 ; Rubber Building Gaskets-Materials in Preformed Solid Vulcanizates Used for Sealing Glazing and Panels-Specification;

22-206)    ISO 3934:1978 ; Rubber Building Gaskets-Materials in Preformed Solid Vulcanizates Used for Sealing Glazing and Panels-Specification;

22-207)    ISO 4633:1983 ; Rubber Seals-Joint Rings for Water Supply, Drainage and Sewerage Pipelines-Specification for Materials;

22-208)    ISO 4633:1983 ; Rubber Seals-Joint Rings for Water Supply, Drainage and Sewerage Pipelines-Specifications for Materials;

22-209)    ISO 4635:1982 ; Rubber, Vulcanized-Preformed Compression Seals for Use

22-210)    ISO 4635:1982 ; Rubber, Vulcanized-Preformed Compression Seals for Use Between Concrete Motorway Paving Sections-Specification for Material;

22-211)     ISO 5013:1985 ; Refractory Products-Determination of Modulus of Rupture at Elevated Temperatures;

22-212)    ISO 5014:1986 ; Refractory Products-Determination of Modulus of Rupture at Ambient Temperature;

22-213)    ISO 5015-6:1984 ; Refractory Bricks-Dimensions-Part 6: Basic Bricks for Oxygen Steel Making Converters;

22-214)    ISO 5016:1986 ; Shaped Insulating Refractory Products-Determination of Bulk Density and True Porosity;

22-215)    ISO 5017:1988 ; Dense Shaped Refractory Products-Determination of Bulk Density,

22-216)    ISO 5018:1983 ; Refractory Materials-Determination of True Density;

22-217)    ISO 5019-1:1984 ; Refractory Bricks-Dimensions-Part I: Rectangular Bricks;

22-218)    ISO 5019-2:1984 ; Refractory Bricks-Dimensions-Part 2: Arch Bricks;

22-219)    ISO 5019-3:1984 ; Refractory Bricks-Dimensions-Part 3: Rectangular Checker Bricks for Regenerative Furnace;

22-220)    ISO 5022:1979 ; Shaped Refractory Products-Sampling and Acceptance Testing;

22-221)    ISO 528:1983 ; Refractory Products-Determination of Pyrometric Cone Equivalent (refractoriness);

22-222)    ISO 5417-1986 ; Refractory Bricks for Use in Rotary Kilns-Dimensions;

22-223)    ISO 5419-4:1988 ; Refractory Bricks-Dimensions-Part 4: Dome Bricks for Electric arc Furnace Roofs;

22-224)    ISO 5892:1981 ; Rubber Building Gaskets-Materials for Preformed Solid Vulcanized Structural Gaskets-Specification;

22-225)    ISO 5892:1981 ; Rubber Building Gaskets-Materials for Preformed Solid Vulcanized Structural Gaskets-Specification;

22-226)    ISO 6447:1983 ; Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings-Specification for Material;

22-227)    ISO 6447:1991 ; Rubber Seals-Joint Rings Used for Gas Supply Pipes and Fittings- Specification for Material;

22-228)    ISO 6589:1983 ; Joints in Building-Laboratory Method of Test for Air Permeability of Joints;

22-229)    ISO 7389:1987 ; Building Construction-Jointing Products-Determination of Elastic Recovery;

22-230)    ISO 7390:1987 ; Building Construction-Jointing Products-Determination of Resistance to Flow;

22-231)    ISO 7727:1984 ; Joints in Building-Principles for Jointing of Building Components-Accommodation of Dimensional Deviations During Construction;

22-232)    ISO 8339:1984 ; Building Construction-Jointing Products-Sealants-Determination of Tensile Properties;

22-233)    ISO 8340:1984 ; Building Construction-Jointing Products-Sealants-Determination of Tensile Properties at Maintained Extension;

22-234)    ISO 8394:1988 ; Building Construction-Jointing Products-Determination of Extrudability of One-Component Sealants;

22-235)    ISO 8656:1988 ; Refractory Products-Sampling of Raw Materials and Unshaped Products;

22-236)    ISO 8840:1987 ; Refractory Materials-Determination of Bulk Density of Granular Materials (Grain Density);

22-237)    ISO 8890:1988 ; Dense Shaped Refractory Products-Determination of Resistance to Sulfuric Acid;

22-238)    ISO 8894-1:1987 ; Refractory Materials-Determination of Thermal Conductivity-

22-239)    ISO 8894-2:1990 ; Refractory Materials-Determination of Thermal Conductivity-

22-240)    ISO 8895:1986 ; Shaped Insulating Refractory Products-Determination of Cold Crushing Strength;

22-241)    ISO 9046:1987 ; Building Construction-Sealants-Determination of Adhesion/ Cohesion Properties at Constant Temperature;

22-242)    ISO 9047:1989 ; Building Construction-Sealants-Determination of Adhesion/ Cohesion Properties at Variable Temperatures;

22-243)    ISO 9205:1988 ; Refractory Bricks for Use in Rotary Kilns-Hot-face Identification Marking;

22-244)    ISO 9331:1991 ; Rubber Seals Joint Rings for Hot Water Supply Pipelines up to 110oC Specifications for the Material.

22-245)    ISO 9631:1991 ; Rubber Seals-Joint Rings for Hot Water Supply Pipelines up to 110oC Specifications for the Material;1-1)             ANSI A108.1-2009 ; Specifications for the Installation of Ceramic Tile with Portland Cement Mortar;

21. SANITARY APPLIANCES AND WATER FITTINGS

건설자재 시험 및 인증 관련 규격목록 21

21. SANITARY APPLIANCES AND WATER FITTINGS

21-1)        ASTM A377 – 03(2008)e1 ; Standard Index of Specifications for Ductile-Iron Pressure Pipe

21-2)        ASTM A53 / A53M – 07 ; Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

21-3)        ASTM A74 – 09 ; Standard Specification for Cast Iron Soil Pipe and Fittings

21-4)        ASTM B209 – 07 ; Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

21-5)        ASTM B251 – 02e1 ; Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube

21-6)        ASTM B302 – 07 ; Standard Specification for Threadless Copper Pipe, Standard Sizes

21-7)        ASTM B306 – 09 ; Standard Specification for Copper Drainage Tube (DWV)

21-8)        ASTM B42 – 02e1 ; Standard Specification for Seamless Copper Pipe, Standard Sizes

21-9)        ASTM B42 – 02e1 ; Standard Specification for Seamless Copper Pipe, Standard Sizes

21-10)      ASTM B429 / B429M – 06 ; Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube

21-11)      ASTM B43 – 09 ; Standard Specification for Seamless Red Brass Pipe, Standard Sizes

21-12)      ASTM B447 – 07 ; Standard Specification for Welded Copper Tube

21-13)      ASTM B745 / B745M – 97(2005) ; Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

21-14)      ASTM B75 – 02 ; Standard Specification for Seamless Copper Tube

21-15)      ASTM B88 – 09 ; Standard Specification for Seamless Copper Water Tube

21-16)      ASTM C14 – 07 ; Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe

21-17)      ASTM C425 – 04(2009) ; Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings

21-18)      ASTM C443 – 05ae1 ; Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

21-19)      ASTM C508 / C508M – 00(2009)e1 ; Standard Specification for Asbestos-Cement Underdrain Pipe

21-20)      ASTM C564 – 09a ; Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings

21-21)      ASTM C654 – 05a ; Standard Specification for Porous Concrete Pipe

21-22)      ASTM C700 – 09 ; Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

21-23)      ASTM C76 – 10a ; Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

21-24)      ASTM D1527 – 99(2005) ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

21-25)      ASTM D1785 – 06 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120

21-26)      ASTM D1869 – 95(2005)e1 ; Standard Specification for Rubber Rings for Asbestos-Cement Pipe

21-27)      ASTM D2235 – 04 ; Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

21-28)      ASTM D2239 – 03 ; Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

21-29)      ASTM D2241 – 09 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)

21-30)      ASTM D2321 – 09 ; Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications ASTM D2464 – 06 Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

21-31)      ASTM D2466 – 06 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40ASTM D2467 – 06 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

21-32)      ASTM D2564 – 04(2009)e1 ; Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

21-33)      ASTM D2609 – 02(2008) ; Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

21-34)      ASTM D2657 – 07 ; Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

21-35)      ASTM D2661 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

21-36)      ASTM D2661 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

21-37)      ASTM D2665 – 09 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

21-38)      ASTM D2672 – 96a(2009) ; Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement

21-39)      ASTM D2729 – 03 ; Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

21-40)      ASTM D2737 – 03 ; Standard Specification for Polyethylene (PE) Plastic Tubing

21-41)      ASTM D2751 – 05 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

21-42)      ASTM D2846 / D2846M – 09b ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

21-43)      ASTM D2846 / D2846M – 09b ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems

21-44)      ASTM D2855 – 96(2010) ; Standard Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings

21-45)      ASTM D2949 – 01a(2008)e1 ; Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

21-46)      ASTM D3034 – 08 ; Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

21-47)      ASTM D3139 – 98(2005) ; Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

21-48)      ASTM D3212 – 07 ; Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

21-49)      ASTM F402 – 05 ; Standard Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

21-50)      ASTM F405 – 05 ; Standard Specification for Corrugated Polyethylene (PE) Pipe and Fittings

21-51)      ASTM F409 – 02(2008) ; Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

21-52)      ASTM F437 – 09 ; Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

21-53)      ASTM F438 – 09 ; Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

21-54)      ASTM F441 / F441M – 09 ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

21-55)      ASTM F442 / F442M – 09 ; Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR)

21-56)      ASTM F493 – 04 ; Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

21-57)      ASTM F628 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

21-58)      ASTM F628 – 08 ; Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core

21-59)      ASTM F656 – 08 ; Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings

21-60)      ASTM F891 – 09 ; Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core

21-61)      BDS 1111:1984 ; Centrifugally Cast (spun) Iron Pressure Pipes for Water, Gas and Sewage;

21-62)      BDS 1162 : 2006 (1st revision) ; Ceramic wash basin and pedestal, ceramic wash basin and pedestals dimension, design & construction, type, permissible deviation

21-63)      BDS 1163 : 1987 ; Specification for Vitreous Sanitary Appliances,

21-64)      BDS 1356:1992 ; Specification for Ferrules for Water Services;

21-65)      BDS 1357: 1992 ; Specification for Washers with Fittings for Water Service;

21-66)      BDS 1361 : 1992 ; Faucets

21-67)      BDS 1361:1992 ; Faucets

21-68)      BDS 1507 : 1995 ; Bib taps used in water supply

21-69)      BDS 1508 : 1995 ; Stop taps used in water supply.Specifies the requirements, dimensions construction, materials and test methods of stop taps used in water supply.

21-70)      BDS 1508:1995 ; Stop taps used in water supply.

21-71)      BDS 1509:1995 ; Pillar taps used in water supply

21-72)      BDS 1562:1997 ; Solvent cements for polyvinyl chloride (PVC) plastic pipe and fitting.

21-73)      BDS 1593 : 1998 ; Plastic sanitary squatting pan

21-74)      BDS 1593:1998 ; Plastic sanitary squatting pan

21-75)      BDS 428:1964 ; Specification for Asbestos Cement Pressure Pipe;

21-76)      BDS 429:1964 ; Specification for Asbestos Cement Building and Sanitary Pipes (under revision);

21-77)      BDS 987 : 1981 ; Sand cast brass screw‐down bib taps and stop taps for water services.

21-78)      BDS EN 1112: 2009 ; Sanitary tapware ‐ Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 – General technical specification

21-79)      BDS EN 1113: 2009 ; Sanitary tapware – Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 – General technical specification

21-80)      BDS EN 1254‐2: 2009 ; Copper and copper alloys ‐ Plumbing fittings – Part 2: Fittings with compression ends for use with copper tubes

21-81)      BDS EN 14506: 2009 ; Devices to prevent pollution by backflow of potable water – Automatic diverter – Family H, type C

21-82)      BDS EN 1717: 2009 ; Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow

21-83)      BDS EN 200: 2009 ; Sanitary tapware — Single taps and combination taps for water supply systems of type 1 and type 2 — General technical specification

21-84)      BDS EN 246: 2009 ; Sanitary tapware – General specifications for flow rate regulators

21-85)      BDS EN 248: 2009 ; Sanitary tapware – General specification for electrodeposited coatings of Ni‐Cr

21-86)      BDS EN 681-1: 2008 ; Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber

21-87)      BDS EN 681-2 : 2008 ; Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers

21-88)      BDS ISO /TR 4191: 2008 ; Unplasticized polyvinyl chloride (PVC-U) pipes for water supply-Recommended practice for laying

21-89)      BDS ISO 11413:2010 ; Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting BDS ISO 11414, Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

21-90)      BDS ISO 1167-1 : 2008 ; Thermoplastics pipes fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure- Part 1: General method

21-91)      BDS ISO 1167-2 : 2008 ; Thermoplastics pipes fittings and assemblies for the conveyance of fluids- Determination of the resistance to internal pressure-

21-92)      BDS ISO 12176-2:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion

21-93)      BDS ISO 12176-3:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 3: Operator’s badge

21-94)      BDS ISO 12176-4:2010 ; Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4: Traceability coding

21-95)      BDS ISO 13479:2010 ; Polyolefin pipes for the conveyance of fluids — Determination of

21-96)      BDS ISO 13761:2010 ; Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 °C

21-97)      BDS ISO 13951:2010 ; Plastics piping systems — Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading

21-98)      BDS ISO 13953:2010 ; Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint

21-99)      BDS ISO 13954:2010 ; Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

21-100)    BDS ISO 13955:2010 ; Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies

21-101)    BDS ISO 13957:2010 ; Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance

21-102)    BDS ISO 14236:2010 ; Plastics pipes and fittings — Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems

21-103)    BDS ISO 161-1 : 2008 ; Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and Nominal Pressures- Part 1: Metric series

21-104)    BDS ISO 161-2 : 2008 ; Thermoplastics pipes for the conveyance of fluids- Nominal outside diameters and Nominal Pressures- Part 2: Inch – based series

21-105)    BDS ISO 1746 : 2008 ; Rubber or Plastics hoses and tubing-Bending tests

21-106)    BDS ISO 18553:2010 ; Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds

21-107)    BDS ISO 18553:2010 ; Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds Amendment 1:2010

21-108)    BDS ISO 2505 : 2008 ; Thermoplastics pipes- Longitudinal reversion – Test method and parameters

21-109)    BDS ISO 2507-2 : 2008 ; Thermoplastics pipes and fittings – Vicat softening temperature- Part 2: Test conditions for Unplasticized poly (Vinyl chloride) (PVC-U) or chlorinated poly (Vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (Vinyl chloride) (PVC-HI) pipes

21-110)     BDS ISO 265-1 : 2008 ; Pipes and fittings of plastics materials- fittings for domestic and industrial waste pipes- Basic dimensions: Metric series- Part 1: Unplasticized Poly (Vinyl chloride) (PVC-U)

21-111)     BDS ISO 3114: 2008 ; Unplasticized polyvinyl chloride (PVC) pipes for potable water supply-Extractability of lead and tin- Test method

21-112)     BDS ISO 3126 : 2008 ; Plastics piping systems-Plastics components- Determination of dimensions

21-113)     BDS ISO 3127: 2008 ; Thermoplastics pipes- Determination of resistance to external blows-Round – the – clock method

21-114)     BDS ISO 3419: 2008 ; Non – alloy and alloy steel butt–welding fittings

21-115)     BDS ISO 3458:2010 ; Assembled joints between fittings and polyethylene (PE)

21-116)     BDS ISO 3459:2010 ; Polyethylene (PE) pressure pipes — Joints assembled with mechanical fittings — Internal under pressure test method and requirement

21-117)     BDS ISO 3501:2010 ; Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of resistance to pull-out

21-118)     BDS ISO 3503:2010 ; Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of leakproofness under internal pressure when subjected to bending

21-119)     BDS ISO 3633: 2008 ; Plastics piping systems for soil and waste discharge (Low and high temperature ) inside buildings- Specifications

21-120)    BDS ISO 3822-‐1: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 1: Method of measurement

21-121)    BDS ISO 3822-‐2: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 2: Mounting and operating conditions for draw‐off taps and mixing valves

21-122)    BDS ISO 3822-‐4: 2009 ; Acoustics: Laboratory tests on noise emission from appliances and equipment used in water supply installations – Part 4: Mounting and operating conditions for special appliances

21-123)    BDS ISO 4065: 2008 ; Thermoplastics pipes- Universal wall thickness table

21-124)    BDS ISO 4422-1: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC-U) for water supply – Specifications – Part 1: General

21-125)    BDS ISO 4422-2: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC-U) for water supply – Specifications – Part 2: Pipes (with or without integral sockets)

21-126)    BDS ISO 4422-3: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride)(PVC-U) for water supply- Specifications – Part 3: Fittings and joints

21-127)    BDS ISO 4422-4: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC-U) for water supply- Specifications- Part 4: Valves and ancillary equipment

21-128)    BDS ISO 4422-5: 2008 ; Pipes and fittings made of unplasticized poly (vinyl chloride) (PVC- U) for water supply- Specifications- Part 5: Fitness for purpose of the system

21-129)    BDS ISO 4427-1:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General

21-130)    BDS ISO 4427-1:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General Technical corrigendum 1: 2010

21-131)    BDS ISO 4427-2:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes

21-132)    BDS ISO 4427-3:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings

21-133)    BDS ISO 4427-5:2010 ; Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system

21-134)    BDS ISO 4433-3: 2008 ; Thermoplastics pipes- Resistance to liquid chemicals- Classification-Part 3: Unplasticized poly (vinyl chloride) (PVC-U), high- impact poly (vinyl chloride) (PVC-HI) and chlorinated poly (vinyl chloride) (PVC –C) pipes

21-135)    BDS ISO 4435: 2008 ; Plastic piping systems for non- pressure underground drainage and sewerage- Unplasticized poly (vinyl chloride) (PVC-U)

21-136)    BDS ISO 4439: 2008 ; Unplasticized polyvinyl chloride (PVC) pipes and fittings – Determination and specification of density

21-137)    BDS ISO 5251: 2008 ; Stainless steel butt–welding fittings

21-138)    BDS ISO 6259-1: 2008 ; Thermoplastics pipes- Determination of tensile properties- Part 1: General test method

21-139)    BDS ISO 6259-2: 2008 ; Thermoplastics pipes- Determination of tensile properties- Part 2: Pipes made of unplasticized poly (vinyl chloride) (PVC-U), Chlorinated poly (vinyl chloride) (PVC-C), and high – impact poly (vinyl chloride) (PVC-HI)

21-140)    BDS ISO 6761: 2008 ; Steel tubes – Preparation of ends of tubes and fittings for welding

21-141)    BDS ISO 6964:2010 ; Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method and basic specification

21-142)    BDS ISO 6992: 2008 ; Unplasticized polyvinyl chloride (PVC-U) pipes for drinking water supply – Extractability of cadmium and mercury occurring as impurities

21-143)    BDS ISO 9624:2010 ; Thermoplastics pipes for fluids under pressure — Mating dimensions of flange adapters and loose backing flanges

21-144)    BS 1010 ; Specification for Draw-Off Taps and Stopvalves for Water Services;

21-145)    BS 1125: 1987 ; Specification for WC Flushing Cisterns (Including Dual Flash Cisterns and Flush Pipes);

21-146)    BS 1212 3 (Parts) ; Specification for Float Operated Valves (excluding floats);

21-147)    BS 1244 ; Metal Sink for Domestic Purposes;

21-148)    BS 1254:1981 ; Specification for C Seats (Plastics);

21-149)    BS 1329:1974 ; Specification for Metal Hand Rinse Basins;

21-150)    BS 1415 ( 2 parts) ; Mixing Valves (Manullay Operated);

21-151)    BS 1876: 1992(1977) ; Specification for Automatic Flushing Cistern for Urinals

21-152)    BS 1968 ; Specification for Floats for Ball Valves (copper);

21-153)    BS 2456: 1973 ; Specification for Floats for Ball Valves (plastic) for Cold and Hot Water

21-154)    BS 3377:1985 ; Specification for Boilers for Use with Domestic Solid Mineral Fuel Appliances;

21-155)    BS 5163: 1986 ; Specification for Predominantly Key-Operated Cast Iron Wedge Gate Valve for Water Works;

21-156)    BS 5433: 1976 ; Specification for Underground Stop valves for Water Services (copper);

21-157)    BS 843: 1976 ; Specification for Thermal Storage Electric Water Heaters;

21-158)    BS 855:1976 ; Specification for Welded Steel Boilers for Central Heating and Indirect Hot Water Supply.

21-159)    IS 404 (Part-I)-1993 ; Specification for Lead Pipes Part I for other than Chemical Purpose (third Revision);

21-160)    ISO 160: 1980 ; Asbestos-Cement Pressure Pipes and Joints;

21-161)    ISO 2531-1991 ; Ductile Iron Pipes, Fittings and Accessories for Pressure Pipelines;

21-162)    ISO 392:1986 ; Asbestos-Cement Pipe Fittings for Building and Sanitary Purposes;

21-163)    ISO 881:1980 ; Asbestos-Cement Pipes, Joints and Fittings for Sewerage and Drainage;

 

 

 

 

 

 

20. PAINTS AND VARNISHES

건설자재 시험 및 인증 관련 규격목록 20

20. PAINTS AND VARNISHES

20-1)        BDS 1005:1981 ; Specification for Ready Mixed Paint, Brushing, Finishing, Stoving, Enamel, Colour as Required;

20-2)        BDS 1064:1983 ; Specification for Varnish, Stoving;

20-3)        BDS 1065:1983 ; Specification for Varnish, Acid Resisting;

20-4)        BDS 1066:1983 ; Specification for Varnish, Finishing, Interior;

20-5)        BDS 1097:1984 ; Specification for Plastic Emulsion Paint.

20-6)        BDS 1141:1986 ; Specification for Ready Mixed Aluminium Priming Paints for Woodwork;

20-7)        BDS 1151:1986 ; Specification for Pavement Marking Paints.

20-8)        BDS 13:1960 ; Specification for Ready Mixed Paints, Varnish, Lacquers and Related Products (under revision);

20-9)        BDS 14:1960 ; Specification for Black Bituminous Paint, Brushing for General Purposes (under revision);

20-10)      BDS 397:1964 ; Specification for Ready Mixed Paint, Brushing, Red Oxide Zinc Chrome, Priming (under revision);

20-11)      BDS 398:1964 ; Specification for Ready Mixed Paint, Spraying, Red Oxide Zinc Chrome, Priming (under revision);

20-12)      BDS 399:1964 ; Specification for Aluminum Paint, Spraying for General Purposes, in Dual Container (under revision);

20-13)      BDS 400:1964 ; Specification for Aluminium Paint, Brushing, for General Purposes in Dual Container (under revision);

20-14)      BDS 401:1964 ; Specification for Varnish, Finishing, Exterior, Type-I, (Synthetic) (Tentative) (under revision);

20-15)      BDS 401:1964 ; Specification for Varnish, Finishing, Exterior, Type-I, (synthetic) (under revision);

20-16)      BDS 402:1989 ; Specification for Ready Mixed Paint, Brushing, Finishing, Semigloss, for General Purposes (First Revision);

20-17)      BDS 499:1965 ; Specification for Ready Mixed Paints, Brushing, for Road Marking (white, yellow and black) (under revision);

20-18)      BDS 500:1965 ; Specification for Distemper Dry (under revision);

20-19)      BDS 616:1966 ; Specification for Enamel, Brushing, Exterior (i) Undercoating, (ii) Finishing, Colour as Required (under revision);

20-20)      BDS 617:1966 ; Specification for Enamel, Brushing, Interior (i) Undercoating, (ii) Finishing, Colour as Required (under revision);

20-21)      BDS 926:1980 ; Specification for Ready Mixed Paint, Brushing, Petrol Resisting, Air Drying, for Exterior Painting of Containers, Colour as Required;

20-22)      BDS 927:1980 ; Specification for Ready Mixed Paint, Brushing, Petrol Resisting, Air Drying, for Interior Painting of Tanks and Containers, Red Oxide (colour unspecified);

20-23)      BDS 928:1980 ; Specification for Ready Mixed Paint, Brushing, Acid Resisting, for Protection Against Acid Fumes, Colour as Required;

20-24)      BDS 973:1981 ; Specification for Specification and Methods of Test for Linseed Stand Oil for Paints and Varnishes;

20-25)      BDS 974:1981 ; Specification and Methods of Test for Raw Tung Oils for Paints and Varnishes;

20-26)      IS 101 ; Methods of sampling and test for paints, varnishes and related products:

20-27)      IS 104:1979 ; Specification for ready mixed paint, brushing, zinc chrome, priming (second revision)

20-28)      IS 109:1968 ; Specification for ready mixed paint, brushing, priming, plaster to Indian Standard colours No. 361 and 631 (first revision)

20-29)      IS 11883:1986 ; Specification for ready mixed paint, brushing, red oxide, priming for metals

20-30)      IS 123:1962 ; Specification for ready mixed paint, brushing, finishing, semi-gloss, for general purposes, to Indian Standard colours No. 445, 446, 448, 449, 451 and 473; and red oxide (colour unspecified) (revised)

20-31)      IS 13183:1991 ; Specification for aluminium paints, heat resistant

20-32)      IS 13213:1991 ; Specification for polyurethane full gloss enamel (two pack)

20-33)      IS 133:1993 ; Specification for enamel, interior (a) undercoating, (b) finishing (third revision)

20-34)      IS 13607:1992 ; Specification for ready mixed paint, finishing, general purposes, synthetic

20-35)      IS 137:1965 ; Specification for ready mixed paint, brushing, matt or egg-shell flat, finishing, interior, to Indian Standard colour, as required (revised)

20-36)      IS 13871:1993 ; Specification for powder coatings

20-37)      IS 14314:1995 ; Specification for thinner general purposes for synthetic paints and varnishes

20-38)      IS 158:1981 ; Specification for ready mixed paint, brushing, bituminous, black, lead-free, acid, alkali, and heat resisting (third revision)

20-39)      IS 168:1993 ; Specification for ready mixed paint, air-drying semi-glossy/matt, for general purposes (third revision)

20-40)      IS 2074:1992 ; Specification for ready mixed paint, air drying red oxide-zinc chrome, priming (second revision)

20-41)      IS 2075:2000 ; Specification for ready mixed paint, stoving, red oxide-zinc chrome, priming (second revision)

20-42)      IS 2339:1963 ; Specification for aluminium paint for general purposes, in dual container

20-43)      IS 2932:2003 ; Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing (third revision)

20-44)      IS 2933:1975 ; Specification for enamel, exterior, (a) undercoating, (b) finishing (first revision)

20-45)      IS 324:1959 ; Specification for ordinary denatured spirit (revised)

20-46)      IS 324-1959 ; Specification for Ordinary Denatured Spirit (revised);

20-47)      IS 337:1975 ; Specification for varnish, finishing, interior (first revision)

20-48)      IS 341:1973 ; Specification for black Japan, Types A, B and C first revision)

20-49)      IS 347-1975 ; Specification for Varnish, Shellac for general purposes (First Revision);

20-50)      IS 348-1968 ; Specification for French Polish (First Revision);

20-51)      IS 3536:1999 ; Specification for ready mixed ‘paint, brushing, wood primer

20-52)      IS 3537:1966 ; Specification for ready mixed paint, finishing, interior for general purposes, to Indian Standard colours No. 101, 216, 217, 219, 275:”281, 352, 353, 358 to 361, 363,364,388,410,442, 444,628, 631,632,634,693,697, white andblack

20-53)      IS 3539:1966 ; Specification for ready mixed paint, undercoating, for use under oil finishes, to Indian Standard colours, as required

20-54)      IS 3585:1966 ; Specification for ready mixed paint, aluminium, brushing, priming, water resistant, for wood work

20-55)      IS 3678:1966 ; Specification for ready mixed paint, thick white, for lettering

20-56)      IS 427:1965 ; Specification for distemper, dry, colour as required (revised)

20-57)      IS 428:2000 ; Specification for distemper, washable (second revision)

20-58)      IS 524:1983 ; Specification for varnish, finishing, exterior, synthetic (second revision)

20-59)      IS 525:196 ; Specification for varnish, finishing, exterior and general purposes (first revision)

20-60)      IS 533:1998 ; Specification for gum spirit of turpentine (oil of turpentine) (second revision)

20-61)      IS 5410:1992 ; Specification for cement paint, colour as required (first revision)

20-62)      IS 5411 ; Specification for plastic emulsion paint:

20-63)      IS 642:1963 ; Specification for varnish medium for aluminium paint (revised)

20-64)      IS 82:1992 ; Methods of sampling and test for thinners and solvents for paints (first revision)

20-65)      IS 8662:1993 ; Specification for enamel, synthetic, exterior, (a) undercoating, (b) finishing, for railway coaches (first revision)

20-66)      IS 9862:1981 ; Specification for ready mixed paint, brushing, bituminous black lead free, acid, alkali, water and chlorine resisting

19. ROOF COVERINGS

건설자재 시험 및 인증 관련 규격목록 19

19. ROOF COVERINGS

19-1)        ASTM A755 / A755M – 03(2008) ; Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Pre-painted by the Coil-Coating Process for Exterior Exposed Building Products

19-2)        ASTM B101 – 07 ; Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction

19-3)        ASTM C1029 – 09 ; Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

19-4)        ASTM C222 – 97(2008) ; Standard Specification for Asbestos-Cement Roofing Shingles

19-5)        ASTM C406 – 06e1 ; Standard Specification for Roofing Slate

19-6)        ASTM C836 / C836M – 10 ; Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

19-7)        ASTM D1227 – 95(2007) ; Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

19-8)        ASTM D1863 – 05 ; Standard Specification for Mineral Aggregate Used on Built-Up Roofs

19-9)        ASTM D2178 – 04 ; Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

19-10)      ASTM D225 – 07 ; Standard Specification for Asphalt Shingles (Organic Felt) Surfaced With Mineral Granules

19-11)      ASTM D226 / D226M – 09 ; Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

19-12)      ASTM D227 – 03 ; Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

19-13)      ASTM D2626 – 04 ; Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

19-14)      ASTM D2898 – 10 ; Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing

19-15)      ASTM D312 – 00(2006) ; Standard Specification for Asphalt Used in Roofing

19-16)      ASTM D3161 – 09 ; Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

19-17)      ASTM D3747 – 79(2007) ; Standard Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

19-18)      ASTM D3909 – 97b(2004)e1 ; Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced With Mineral Granules

19-19)      ASTM D4272 – 09 ; Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop

19-20)      ASTM D4434 / D4434M – 09 ; Standard Specification for Poly(Vinyl Chloride) Sheet Roofing

19-21)      ASTM D450 – 07 ; Standard Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing

19-22)      ASTM D4601 – 04 ; Standard Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing

19-23)      ASTM D4637 – 08 ; Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane

19-24)      ASTM D4897 / D4897M – 01(2009) ; Standard Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing

19-25)      ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

19-26)      ASTM D6380 – 03(2009) ; Standard Specification for Asphalt Roll Roofing (Organic Felt)

19-27)      ASTM E108 – 10a ; Standard Test Methods for Fire Tests of Roof Coverings

19-28)      ASTM G154 – 06 ; Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

19-29)      ASTM G155 – 05a ; Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

19-30)      ASTM G90 – 05 ; Standard Practice for Performing Accelerated Outdoor Weathering of Nonmetallic Materials Using Concentrated Natural Sunlight

19-31)      BDS 1046:1983 ; Specification for Asbestos Cement Products – Corrugated Sheets and Fittings for Roofing and Cladding;

19-32)      BDS 1122:1985 ; Specification for Hot-dip Galvanized Steel and Coil.

19-33)      BDS 430:1964 ; Specification for Asbestos Cement Corrugated Sheets for Roofing and Cladding

19-34)      BDS 431:1964 ; Specification for Asymmetrical Section Corrugated Sheets in Asbestos Cement for Roofing and Cladding

19-35)      BDS 579:1966 ; Specification for Asbestos Cement Flat Sheets (under revision);

19-36)      BDS 868:1978 ; Code of Practice for Galvanized Corrugated Sheet Roof and Wall Coverings;

19-37)      BDS EN 1024: 2008 ; Clay roofing tiles for discontinuous laying — Determination of geometric characteristics

19-38)      BDS EN 1304: 2008 ; Clay roofing tiles and fittings — Product definitions and specifications

19-39)      BDS EN 490: 2008 ; Concrete roofing tiles and fittings for roof covering and all cladding — Product specifications

19-40)      BDS EN 49l: 2008 ; Concrete roofing tiles and fittings for roof covering and wall cladding — Test methods

19-41)      BDS EN 538: 2008 ; Clay roofing tiles for discontinuous laying — Flexural strength test

19-42)      BDS EN 539-l: 2008 ; Clay roofing tiles for discontinuous laying Determination of physical characteristics — Part 1: Impermeability test

18. BUILDERS HARDWARE 건설자재 시험 및 인증 관련 규격목록 18

건설자재 시험 및 인증 관련 규격목록 18

18. BUILDERS HARDWARE

18-1)        BDS 113:1986 ; Specification for Latches and Locks for Doors in Buildings;

18-2)        IS 10019-1981 ; Specification for Steel Window Stays and Fasteners;

18-3)        IS 10090-1982 ; Specification for Numericals;

18-4)        IS 1019-1974 ; Specification for Rim Latches (Second Revision);

18-5)        IS 10342-1982 ; Specification for Curtain Rail System

18-6)        IS 12817:1997 ; Specification for stainless steel butt hinges (first revision)

18-7)        IS 12867:1989 ; Specification for PVC hand rails covers

18-8)        IS 1341-1992 ; Specification for Steel Butt Hinges (Sixth Revision);

18-9)        IS 14912:2001 ; Specification for door closers concealed type (hydraulically regulated)

18-10)      IS 1823-1980 ; Specification for Floor Door Stoppers (Third Revision);

18-11)      IS 1837-1966 ; Specification for Fanlight Pivots (First Revision);

18-12)      IS 204-1991/1992 ; Specification for Tower Bolts;

18-13)      IS 205-1992 ; Specification for Nonferrous Metal Butt Hinges (fourth Revision);

18-14)      IS 206-1992 ; Specification for Tee and Strap Hinges (Fourth Revision);

18-15)      IS 208-1996 ; Specification for Door Handles (Fifth Revision);

18-16)      IS 2209-1976 ; Specification for Mortice Locks (vertical type) (Third Revision);

18-17)      IS 2681-1993 ; Specification for Nonferrous Metal Sliding Door Bolts for Use with Padlocks (Third Revision);

18-18)      IS 281-1991 ; Specification for Mild Steel Sliding Door Bolts for Use with Padlock (Third Revision);

18-19)      IS 3564-1995 ; Specification for Door Closers (hydraulically regulated) (Second Revision);

18-20)      IS 362-1991 ; Specification for Parliament Hinges (Fifth Revision);

18-21)      IS 363-1993 ; Specification for Hasps and Staples (Fourth Revision);

18-22)      IS 364-1993 ; Specification for Fanlight Catch (Third Revision);

18-23)      IS 3818-1992 ; Specification for Continuous (piano) Hinges (Third Revision);

18-24)      IS 3828-1966 ; Specification for Ventilator Chains;

18-25)      IS 3843-1995 ; Specification for Steel Backflap Hinges; (First Revision)

18-26)      IS 3847-1992 ; Specification for Mortice Night Latches; (First Revision)

18-27)      IS 452-1973 ; Specification for Door Springs, Rat-tail Type (Second Revision);

18-28)      IS 453-1993 ; Specification for Double Acting Spring Hinges (Third Revision);

18-29)      IS 4621-1975 ; Specification for Indicating Bolts for use in Public Baths and Lavatories (First Revision);

18-30)      IS 4948-2002 ; Specification for Welded Steel Wire Fabric for General Use (Second Revision);

18-31)      IS 4992-1975 ; Specification for Door Handles for Mortice Locks (vertical type) (First Revision);

18-32)      IS 5187-1972 ; Specification for Flush Bolts (First Revision);

18-33)      IS 5899-1970 ; Specification for Bathroom Latches;

18-34)      IS 5930-1970 ; Specification for Mortice Latch (vertical type);

18-35)      IS 6315-1971 ; Specification for Floor Springs (hydraulically regulated) for Heavy Doors;

18-36)      IS 6318-1971 ; Specification for Plastic Window Stays and Fasteners;

18-37)      IS 6343-1982 ; Specification for Door Closers (pneumatically regulated) for Light Doors Weighing up to 40 kg (First Revision);

18-38)      IS 6602-1972 ; Specification for Ventilator Poles;

18-39)      IS 6607-1972 ; Specification for Rebated Mortice Locks (vertical type);

18-40)      IS 7196-1974 ; Specification for Hold Fast;

18-41)      IS 7197-1974 ; Specification for Double Action Floor Springs (without oil check) for Heavy Doors;

18-42)      IS 729-1979 ; Specification for Drawer Locks, Cupboard Locks and Box Locks (Third Revision);

18-43)      IS 7534-1985 ; Specification for sliding locking bolts for use with padlocks (first revision);

18-44)      IS 7540-1974 ; Specification for Mortice Dead Locks;

18-45)      IS 8756-1978 ; Specification for Ball Catches for use in Wooden Almirah;

18-46)      IS 8760-1978 ; Specification for Mortice Sliding Door Locks, with Lever Mechanism;

18-47)      IS 9106-1979 ; Specification for Rising Butt Hinges;

18-48)      IS 9131-1979 ; Specification for Rim Locks;

18-49)      IS 9460-1980 ; Specification Flush Drop Handle for Drawer;

18-50)      IS 9899-1981 ; Specification for Hat, Coat and Wardrobe Hooks;

 

17. ALUMINIUM AND ALUMINIUM ALLOYS

건설자재 시험 및 인증 관련 규격목록 17

17. ALUMINIUM AND ALUMINIUM ALLOYS

17-1)        ASTM B108 / B108M – 08 ; Standard Specification for Aluminum-Alloy Permanent Mold Castings

17-2)        ASTM B209 – 07 ; Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

17-3)        ASTM B210 – 04 ; Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

17-4)        ASTM B211 – 03 ; Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire

17-5)        ASTM B221 – 08 ; Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

17-6)        ASTM B241 / B241M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

17-7)        ASTM B26 / B26M – 09 ; Standard Specification for Aluminum-Alloy Sand Castings

17-8)        ASTM B308 / B308M – 02 ; Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles

17-9)        ASTM B313 / B313M – 09 ; Standard Specification for Aluminum and Aluminum-Alloy Round Welded Tubes

17-10)      ASTM B316 / B316M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods

17-11)      ASTM B429 / B429M – 06 ; Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube

17-12)      ASTM B483 / B483M – 03 ; Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applications

17-13)      ASTM B547 / B547M – 02 ; Standard Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round Tube

17-14)      ASTM B632 / B632M – 08 ; Standard Specification for Aluminum-Alloy Rolled Tread Plate

17-15)      ASTM B745 / B745M – 97(2005) ; Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

17-16)      ASTM B85 / B85M – 09 ; Standard Specification for Aluminum-Alloy Die Castings

17-17)      ASTM E34 – 94(2002) ; Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys

17-18)      BDS EN 12020-1:2010 ; Aluminium and aluminium alloys— Extruded precision profiles in alloys EN AW-6060 and EN AW-6063— Part 1: Technical conditions for inspection and delivery

17-19)      BDS EN 12020-2:2010 ; Aluminium and aluminium alloys — Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 — Part 2: Tolerances on dimensions and form

17-20)      BDS EN 515:2010 ; Aluminium and aluminium alloys — Wrought products — Temper designations

17-21)      BDS EN 755-1:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 1: Technical conditions for inspection and delivery

17-22)      BDS EN 755-2:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: Mechanical properties

17-23)      BDS EN 755-3:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 3: Round bars, tolerances on dimensions and form

17-24)      BDS EN 755-4:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 4: Square bars, tolerances on dimensions and form

17-25)      BDS EN 755-5:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 5: Rectangular bars, tolerances on dimensions and form

17-26)      BDS EN 755-6:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 6: Hexagonal bars, tolerances on dimensions and

17-27)      BDS EN 755-7:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 7: Seamless tubes, tolerances on dimensions and form

17-28)      BDS EN 755-8:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 8: Porthole tubes, tolerances on dimensions and form

17-29)     BDS EN 755-9:2010 ; Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 9: Profiles, tolerances on dimensions and form

 

16. DOORS, WINDOWS AND VENTILATORS

건설자재 시험 및 인증 관련 규격목록 16

16. DOORS, WINDOWS AND VENTILATORS

16-1)        BDS 1270: 1990 ; Specification for Strong Room Door;

16-2)        BDS 1273: 1990 ; Specification for Vault Doors;

16-3)        BDS 142:1961 ; Specification for Wood Door (under revision);

16-4)        BDS 1504:1996 ; Timber door window and ventilator frames

16-5)        BDS 173:1962 ; Specification for Wood Windows (under revision);

16-6)        BDS 820:1978 ; Recommendation for Maximum Permissible Moisture Content of Timber Used for Different Purposes in Bangladesh;

16-7)        BDS EN 12608: 2008 ; Unplasticized polyvinylchloride (PVC – U) profiles for the fabrication of windows and doors — Classification, requirements and test methods

16-8)        BDS EN 477: 2008 ; Unplasticized polyvinylchloride (PVC – U) profiles for the fabrication of windows and doors — Determination of the resistance to impact of main profiles by falling mass

16-9)        BDS EN 478: 2008 ; Unplasticized polyvinylchloride (PVC – U) profiles for the fabrication of windows and doors — Determination of appearance after exposure at 150 ºC

16-10)      BDS EN 479: 2008 ; Unplasticized polyvinylchloride (PVC – U) profiles for the fabrication of windows and doors — Determination of heat reversion

16-11)      BDS EN 513: 2008 ; Unplasticized polyvinylchloride (PVC – U) profiles for the fabrication of windows and doors — Determination of the resistance to artificial weathering

16-12)      BDS EN 514: 2008 ; Unplasticized polyvinylchloride (PVC – U) profiles for the fabrication of windows and doors — Determination of the

16-13)      BDS ISO 1163-1:2008 ; Plastics — Unplasticized poly (vinyl chloride) (PVC – U) moulding and extrusion materials — Part 1: Designation system and basis for specifications

16-14)      BDS ISO 1163-2:2008 ; Plastics — Unplasticized poly (vinyl chloride) (PVC – U) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties

16-15)      IS 1003-2003/1994 ; Specification for Timber Panelled and Glazed Shutters;

16-16)      IS 1038-1983 ; Specification for Steel Doors, Windows and Ventilators (Third Revision);

16-17)      IS 10451-1983 ; Specification for Steel Sliding Shutters (top hung type);

16-18)      IS 10521-1983 ; Specification for Collapsible Gates;

16-19)      IS 1361-1978 ; Specification for Steel Windows for Industrial Buildings (First Revision);

16-20)      IS 14856:2000 ; Specification for glass fibre reinforced (GRP) panel type door shutters for internal use

16-21)      IS 15380:2003 ; Specification for moulded raised high density fibre (HDF) panel doors

16-22)      IS 1826-1961 ; Specification for Venetian Blinds for Windows;

16-23)      IS 1948-1961 ; Specification for Aluminium Doors, Windows and Ventilators;

16-24)      IS 1949-1961 ; Specification for Aluminium Windows for Industrial Buildings;

16-25)      IS 2191-1983 ; Specification for Wooden Flush Door Shutters (cellular and hollow core type);

16-26)      IS 2202-1991/83 ; Specification for Wooden Flush Door Shutters (solid core type);

16-27)      IS 4020-1998 ; Method of tests for door shutters:

16-28)      IS 4021:1995 ; Specification for timber door, window and ventilator frames

16-29)      IS 4351-2003 ; Specification for Steel Door Frames (Second Revision);

16-30)      IS 4962:1968 ; Specification for wooden side sliding doors

16-31)      IS 6198:1992 ; Specification for ledged, braced and battened timber shutters (second revision)Revision);

16-32)      IS 6248-1979 ; Specification for Metal Rolling Shutters and Rolling Grills (First Revision);

16-33)      IS 7452-1990 ; Specification for Hot Rolled Steel Sections for Doors, Windows and Ventilators (Second Revision);