STD-ASTM C XXXX

아래 ASTM (American Society for Testing and Materials) 규격 목록은 규격번호와 제목을 발췌, 나열한 것입니다.
[출처 : www.astm.org ]

ASTM A , ASTM B ,  ASTM C 1 || 2 || 3 |,  ASTM D , ASTM E ASTM F , ASTM G ,

[ASTM C000 – C999]

  • ASTM C10 : EN-Standard Specification for Natural Cement
  • ASTM C10/C10M : EN-Standard Specification for Natural Cement
  • ASTM C1000 : EN-Standard Test Method for Radiochemical Determination of Uranium Isotopes in Soil by Alpha Spectrometry
  • ASTM C1001 : EN-Standard Test Method for Radiochemical Determination of Plutonium in Soil by Alpha Spectroscopy
  • ASTM C1002 : EN-Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
  • ASTM C1002 REV A : EN-Standard Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases
  • ASTM C1003 : EN-Standard Test Method for Thermal Performance of Cooling-Air Duct Sections Using a Calibrated Hot Box
  • ASTM C1004 : EN-Standard Matrix for LWR Spent Fuel Receiving and Storage
  • ASTM C1005 : EN-Standard Specification for Reference Masses and Devices for Determining Mass for Use in the Physical Testing of Hydraulic Cements
  • ASTM C1006 : EN-Standard Test Method for Splitting Tensile Strength of Masonry Units
  • ASTM C1007 : EN-STANDARD SPECIFICATION FOR INSTALLATION OF LOAD BEARING (TRANSVERSE AND AXIAL) STEEL STUDS AND RELATED ACCESSORIES (R 1990)
  • ASTM C1007 REV A : EN-Standard Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
  • ASTM C1008 : EN-STANDARD SPECIFICATION FOR SINTERED (URANIUM- PLUTONIUM) DIOXIDE PELLETS – FAST REACTOR FUEL
  • ASTM C1009 : EN-STANDARD GUIDE FOR ESTABLISHING A QUALITY ASSURANCE PROGRAM FOR ANALYTICAL CHEMISTRY LABORATORIES WITHIN THE NUCLEAR INDUSTRY
  • ASTM C1010 : EN-Standard Guide for Acceptance Checkout and Pre-Operational Testing of a Nuclear Fuels Reprocessing Facility
  • ASTM C1011 : EN-Standard Guide for Selection or Specification of Electrodeless Conductivity Instruments for the Nuclear Fuel Cycle
  • ASTM C1012 : EN-STANDARD TEST METHOD FOR LENGTH CHANGE OF HYDRAULIC-CEMENT MORTARS EXPOSED TO A SULFATE SOLUTION
  • ASTM C1012 REV A : EN-Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
  • ASTM C1012/C1012M : EN-Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
  • ASTM C1013 : EN-STANDARD SPECIFICATION FOR MEMBRANE-FACED RIGID CELLULAR POLYURETHANE ROOF INSULATION
  • ASTM C1014 : EN-Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation
  • ASTM C1014 REV A : EN-Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation
  • ASTM C1015 : EN-Standard Practice for Installation of Cellulosic and Mineral Fiber Loose-Fill Thermal Insulation
  • ASTM C1016 : EN-STANDARD TEST METHOD FOR DETERMINATION OF WATER ABSORPTION BY SEALANT BACKUP (JOINT FILLER) MATERIAL
  • ASTM C1016 REV A : EN-Standard Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material
  • ASTM C1017 : EN-Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete
  • ASTM C1017/C1017M : EN-Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete
  • ASTM C1018 : EN-STANDARD TEST METHOD FOR FLEXURAL TOUGHNESS AND FIRST-CRACK STRENGTH OF FIBER-REINFORCED CONCRETE (USING BEAM WITH THIRD-POINT LOADING)
  • ASTM C1018 REV A : EN-STANDARD TEST METHOD FOR FLEXURAL TOUGHNESS AND FIRST-CRACK STRENGTH OF FIBER-REINFORCED CONCRETE (USING BEAM WITH THIRD-POINT LOADING)
  • ASTM C1018 REV B : EN-Standard Test Method for Flexural Toughness and First-Crack Strength of Fiber-Reinforced Concrete (Using Beam with Third-Point Loading)
  • ASTM C1019 : EN-STANDARD METHOD OF SAMPLING AND TESTING GROUT
  • ASTM C1019 REV A : EN-Standard Test Method for Sampling and Testing Grout
  • ASTM C1019 REV B : EN-Standard Test Method for Sampling and Testing Grout
  • ASTM C1020 : EN-Standard Matrix for Light Water Reactor Fuel Reprocessing
  • ASTM C1021 : EN-Standard Practice for Laboratories Engaged in the Testing of Building Sealants
  • ASTM C1022 : EN-Standard Test Methods for Chemical and Atomic Absorption Analysis of Uranium-Ore Concentrate
  • ASTM C1023 : EN-Standard Practice for Labeling Ceramic Art Materials for Chronic Adverse Health Hazards
  • ASTM C1025 : EN-STANDARD TEST METHOD FOR MODULUS OF RUPTURE IN BENDING OF ELECTRODE GRAPHITE
  • ASTM C1026 : EN-STANDARD TEST METHOD FOR MEASURING THE RESISTANCE OF CERAMIC TILE TO FREEZE-THAW CYCLING
  • ASTM C1027 : EN-Standard Test Method for Determining Visible Abrasion Resistance of Glazed Ceramic Tile
  • ASTM C1028 : EN-Standard Test Method for Determining the Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull-Meter Method
  • ASTM C1029 : EN-Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation
  • ASTM C1029 REV A : EN-Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation
  • ASTM C1030 : EN-STANDARD TEST METHOD FOR DETERMINATION OF PLUTONIUM ISOTOPIC COMPOSITION BY GAMMA-RAY SPECTROMETRY
  • ASTM C1031 : EN-Standard Specification for Nuclear-Grade Aluminum Oxide Powder
  • ASTM C1032 : EN-Standard Specification for Woven Wire Plaster Base
  • ASTM C1033 : EN-Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation Installed Vertically
  • ASTM C1034 : EN-Standard Test Method for Lead and Cadmium Extracted from Glazed Ceramic Cookwear
  • ASTM C1035 : EN-Standard Specification for Lead and Cadmium Extracted from Glazed Ceramic Cookwear
  • ASTM C1036 : EN-STANDARD SPECIFICATION FOR FLAT GLASS
  • ASTM C1037 : EN-Standard Practice for Inspection of Underground Precast Concrete Utility Structures
  • ASTM C1038 : EN-STANDARD TEST METHOD FOR EXPANSION OF PORTLAND CEMENT MORTAR BARS STORED IN WATER
  • ASTM C1039 : EN-Standard Test Methods for Apparent Porosity Apparent Specific Gravity and Bulk Density of Graphite Electrodes
  • ASTM C1040 : EN-Standard Test Methods for In-Place Density of Unhardened and Hardened Concrete Including Roller Compacted Concrete By Nuclear Methods
  • ASTM C1040/C1040M : EN-Standard Test Methods for In-Place Density of Unhardened and Hardened Concrete Including Roller Compacted Concrete By Nuclear Methods
  • ASTM C1041 : EN-Standard Practice for In-Situ Measurements of Heat Flux in Industrial Thermal Insulation Using Heat Flux Transducers
  • ASTM C1042 : EN-Standard Test Method for Bond Strength of Latex Systems Used with Concrete by Slant Shear
  • ASTM C1043 : EN-Standard Practice for Guarded-Hot-Plate Design Using Circular Line-Heat Sources
  • ASTM C1044 : EN-Standard Practice for Using a Guarded-Hot-Plate Apparatus or Thin-Heater Apparatus in the Single-Sided Mode
  • ASTM C1045 : EN-STANDARD PRACTICE FOR CALCULATING THERMAL TRANSMISSION PROPERTIES FROM STEADY-STATE HEAT FLUX MEASUREMENTS
  • ASTM C1046 : EN-Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components
  • ASTM C1047 : EN-Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
  • ASTM C1048 : EN-STANDARD SPECIFICATION FOR HEAT-TREATED FLAT GLASS – KIND HS KIND FT COATED AND UNCOATED GLASS
  • ASTM C1068 : EN-Standard Guide for Qualification of Measurement Methods by a Laboratory within the Nuclear Industry
  • ASTM C1069 : EN-Standard Test Method for Specific Surface Area of Alumina or Quartz by Nitrogen Adsorption
  • ASTM C107 : EN-STANDARD METHOD OF PANEL SPALLING TESTING HIGH-DUTY FIRECLAY BRICK
  • ASTM C1070 : EN-Standard Test Method for Determining Particle Size Distribution of Alumina or Quartz by Laser Light Scattering
  • ASTM C1071 : EN-STANDARD SPECIFICATION FOR THERMAL AND ACOUSTICAL INSULATION (MINERAL FIBER DUCT LINING MATERIAL) (E1-1988)
  • ASTM C1072 : EN-Standard Test Method for Measurement of Masonry Flexural Bond Strength
  • ASTM C1072 REV A : EN-Standard Test Method for Measurement of Masonry Flexural Bond Strength
  • ASTM C1072 REV B : EN-Standard Test Method for Measurement of Masonry Flexural Bond Strength
  • ASTM C1073 : EN-STANDARD TEST METHOD FOR HYDRAULIC ACTIVITY OF GROUND SLAG BY REACTION WITH ALKALI
  • ASTM C1073 REV A : EN-Standard Test Method for Hydraulic Activity of Ground Slag by Reaction with Alkali
  • ASTM C1074 : EN-Standard Practice for Estimating Concrete Strength by the Maturity Method
  • ASTM C1075 : EN-Standard Practices for Sampling Uranium-Ore Concentrate
  • ASTM C1076 : EN-Standard Specification for Nuclear Grade Hafnium Oxide Pellets
  • ASTM C1077 : EN-Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation
  • ASTM C1077 REV A : EN-STANDARD PRACTICE FOR LABORATORIES TESTING CONCRETE AND CONCRETE AGGREGATES FOR USE IN CONSTRUCTION AND CRITERIA FOR LABORATORY EVALUATION
  • ASTM C1077 REV B : EN-Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation
  • ASTM C1078 : EN-Standard Test Methods for Determining the Cement Content of Freshly Mixed Concrete
  • ASTM C1079 : EN-Standard Test Methods for Determining the Water Content of Freshly Mixed Concrete
  • ASTM C108 : EN-Standard Symbols for Heat Transmission
  • ASTM C1080 : EN-Standard Specification for Asbestos-Cement Products Other Than Fill for Cooling Towers
  • ASTM C1081 : EN-Standard Specification for Asbestos-Cement Corrugated Fill For Use in Cooling Towers
  • ASTM C1082 : EN-STANDARD SPECIFICATION FOR ASBESTOS-CEMENT FLAT SHEET FOR COOLING TOWER FILL
  • ASTM C1083 : EN-STANDARD TEST METHOD FOR WATER ABSORPTION OF CELLULAR ELASTOMERIC GASKETS AND SEALING MATERIALS
  • ASTM C1084 : EN-Standard Test Method for Portland-Cement Content of Hardened Hydraulic-Cement Concrete
  • ASTM C1085 : EN-Standard Specification for Butyl Rubber-Based Solvent-Release Sealants
  • ASTM C1086 : EN-Standard Specification for Glass Fiber Mechanically Bonded Felt Thermal Insulation
  • ASTM C1086 REV A : EN-Standard Specification for Glass Fiber Felt Thermal Insulation
  • ASTM C1087 : EN-Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
  • ASTM C1088 : EN-Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
  • ASTM C1088 REV A : EN-Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
  • ASTM C1089 : EN-Standard Specification for Spun Cast Prestressed Concrete Poles
  • ASTM C109 : EN-STANDARD TEST METHOD FOR COMPRESSIVE STRENGTH OF HYDRAULIC CEMENT MORTARS (USING 2-IN. OR 50-MM CUBE SPECIMENS)
  • ASTM C109 REV A : EN-STANDARD TEST METHOD FOR COMPRESSIVE STRENGTH OF HYDRAULIC CEMENT MORTARS (USING 2-IN. OR 50-MM CUBE SPECIMENS)
  • ASTM C109/C109M : EN-Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
  • ASTM C1090 : EN-STANDARD TEST METHOD FOR MEASURING CHANGES IN HEIGHT OF CYLINDRICAL SPECIMENS FROM HYDRAULIC-CEMENT GROUT
  • ASTM C1091 : EN-Standard Test Method for Hydrostatic Infiltration and Exfiltration Testing of Vitrified Clay Pipe Lines
  • ASTM C1091 REV A : EN-Standard Test Method for Hydrostatic Infiltration Testing of Vitrified Clay Pipe Lines
  • ASTM C1092 : EN-Standard Specification for Glass Reinforced Concrete D-Load Culvert Storm Drain and Sewer Pipe
  • ASTM C1093 : EN-Standard Practice for Accreditation of Testing Agencies for Unit Masonry
  • ASTM C1094 : EN-Standard Guide for Flexible Removable Insulation Covers
  • ASTM C1095 : EN-STANDARD PRACTICE FOR CALCULATING PRECISION DATA ON REFRACTORIES (C08) FROM INTERLABORATORY TEST RESULTS
  • ASTM C1095 REV A : EN-Standard Practice for Calculating Precision Data on Refractories (C08) from Interlaboratory Test Results
  • ASTM C1096 : EN-STANDARD TEST METHOD FOR DETERMINATION OF WOOD FIBER IN ASBESTOS CEMENT
  • ASTM C1097 : EN-STANDARD SPECIFICATION FOR HYDRATED LIME FOR USE IN ASPHALTIC- CONCRETE MIXTURES
  • ASTM C1097 REV A : EN-Standard Specification for Hydrated Lime for Use in Asphalt Cement or Bituminous Pavements
  • ASTM C1098 : EN-Standard Specification for Nuclear-Grade Hafnium Oxide Powder-(Discontinued 2002; No Replacement)
  • ASTM C1099 : EN-Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
  • ASTM C11 : EN-Standard Terminology Relating to Gypsum and Related Building Materials and Systems
  • ASTM C11 REV A : EN-STANDARD DEFINITIONS OF TERMS RELATING TO GYPSUM AND RELATED BUILDING MATERIALS AND SYSTEMS
  • ASTM C11 REV B : EN-STANDARD TERMINOLOGY RELATING TO GYPSUM AND RELATED BUILDING MATERIALS AND SYSTEMS
  • ASTM C11 REV C : EN-Standard Terminology Relating to Gypsum and Related Building Materials and Systems
  • ASTM C11 REV D : EN-Standard Terminology Relating to Gypsum and Related Building Materials and Systems
  • ASTM C110 : EN-Standard Test Methods for Physical Testing of Quicklime Hydrated Lime and Limestone
  • ASTM C110 REV A : EN-Standard Test Methods for Physical Testing of Quicklime Hydrated Lime and Limestone
  • ASTM C110 REV B : EN-STANDARD TEST METHODS FOR PHYSICAL TESTING OF QUICKLIME HYDRATED LIME AND LIMESTONE
  • ASTM C1100 : EN-Standard Test Method for Ribbon Thermal Shock Testing of Refractory Materials
  • ASTM C1101/C1101M : EN-Standard Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation
  • ASTM C1102 : EN-STANDARD TEST METHOD FOR TIME OF SETTING OF PORTLAND-CEMENT PASTES CONTAINING ACCELERATING ADMIXTURES FOR SHOTCRETE BY THE USE OF GILLMORE NEEDLES
  • ASTM C1103 : EN-STANDARD PRACTICE FOR JOINT ACCEPTANCE TESTING OF INSTALLED PRECAST CONCRETE PIPE SEWER LINES
  • ASTM C1103M : EN-Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines [Metric]
  • ASTM C1104/C1104M : EN-Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
  • ASTM C1105 : EN-Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
  • ASTM C1105 REV A : EN-Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
  • ASTM C1106 : EN-Standard Test Methods for Chemical Resistance and Physical Properties of Carbon Brick
  • ASTM C1107 : EN-Standard Specification for Packaged Dry Hydraulic-Cement Grout (Nonshrink)
  • ASTM C1107 REV A : EN-Standard Specification for Packaged Dry Hydraulic-Cement Grout (Nonshrink)
  • ASTM C1107/C1107M : EN-Standard Specification for Packaged Dry Hydraulic-Cement Grout (Nonshrink)
  • ASTM C1107/C1107M REV A : EN-Standard Specification for Packaged Dry Hydraulic-Cement Grout (Nonshrink)
  • ASTM C1108 : EN-Standard Test Method for Plutonium by Controlled-Potential Coulometry
  • ASTM C1109 : EN-STANDARD TEST METHOD FOR ANALYSIS OF AQUEOUS LEACHATES FROM NUCLEAR WASTE MATERIALS USING INDUCTIVELY COUPLED PLASMA-ATOMIC EMISSION SPECTROMETRY
  • ASTM C1110 : EN-Standard Practice for Sample Preparation for X-Ray Emission Spectrometric Analysis of Uranium in Ores Using the Glass Fusion or Pressed Powder Method
  • ASTM C1111 : EN-Standard Test Method for Determining Elements in Waste Streams by Inductively Coupled Plasma-Atomic Emission Spectroscopy
  • ASTM C1112 : EN-Standard Guide for Application of Radiation Monitors to the Control and Physical Security of Special Nuclear Material
  • ASTM C1113 : EN-Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique)
  • ASTM C1113/C1113M : EN-Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique)
  • ASTM C1114 : EN-STANDARD TEST METHOD FOR STEADY-STATE THERMAL TRANSMISSION PROPERTIES BY MEANS OF THE THIN- HEATER APPARATUS
  • ASTM C1115 : EN-Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
  • ASTM C1116 : EN-Standard Specification for Fiber-Reinforced Concrete and Shotcrete
  • ASTM C1116/C1116M : EN-Standard Specification for Fiber-Reinforced Concrete
  • ASTM C1116/C1116M REV A : EN-Standard Specification for Fiber-Reinforced Concrete
  • ASTM C1117 : EN-Standard Test Method for Time of Setting of Shotcrete Mixtures by Penetration Resistance
  • ASTM C1118 : EN-Standard Guide for Selecting Components for Wavelength-Dispersive X-Ray Fluorescence (XRF) Systems
  • ASTM C1119 : EN-Standard Test Method for Vacuum Drainage of Asbestos-Cement Mixes
  • ASTM C1119/C1119M : EN-Standard Test Method for Vacuum Drainage of Asbestos-Cement Mixes
  • ASTM C1120 : EN-Standard Test Method for Wash Test of Asbestos
  • ASTM C1121 : EN-Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos
  • ASTM C1121/C1121M : EN-Standard Test Method for Turner and Newall (T and N) Wet-Length Classification of Asbestos
  • ASTM C1122 : EN-Standard Test Method for Wet Volume of Asbestos
  • ASTM C1122/C1122M : EN-Standard Test Method for Wet Volume of Asbestos
  • ASTM C1123 : EN-Standard Test Method for Compressibility and Recovery of Asbestos
  • ASTM C1123/C1123M : EN-Standard Test Method for Compressibility and Recovery of Asbestos
  • ASTM C1124 : EN-Standard Test Method for Kerosene Retention of Asbestos
  • ASTM C1124/C1124M : EN-Standard Test Method for Kerosene Retention of Asbestos
  • ASTM C1125 : EN-Standard Test Method for Penetration Index of Asbestos
  • ASTM C1126 : EN-Standard Specification for Faced or Unfaced Rigid Cellular Phenolic Thermal Insulation
  • ASTM C1127 : EN-Standard Guide for Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
  • ASTM C1128 : EN-Standard Guide for Preparation of Working Reference Materials for Use in Analysis of Nuclear Fuel Cycle Materials
  • ASTM C1129 : EN-Standard Practice for Estimation of Heat Savings by Adding Thermal Insulation to Bare Valves and Flanges
  • ASTM C113 : EN-Standard Test Method for Reheat Change of Refractory Brick
  • ASTM C1130 : EN-Standard Practice for Calibrating Thin Heat Flux Transducers
  • ASTM C1131 : EN-Standard Practice for Least Cost (Life Cycle) Analysis of Concrete Culvert Storm Sewer and Sanitary Sewer Systems
  • ASTM C1132 : EN-STANDARD PRACTICE FOR CALIBRATION OF THE HEAT FLOW METER APPARATUS
  • ASTM C1133 : EN-Standard Test Method for Nondestructive Assay of Special Nuclear Material in Low-Density Scrap and Waste by Segmented Passive Gamma-Ray Scanning
  • ASTM C1133/C1133M : EN-Standard Test Method for Nondestructive Assay of Special Nuclear Material in Low-Density Scrap and Waste by Segmented Passive Gamma-Ray Scanning
  • ASTM C1134 : EN-Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion
  • ASTM C1135 : EN-Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
  • ASTM C1136 : EN-Standard Specification for Flexible Low Permeance Vapor Retarders for Thermal Insulation
  • ASTM C1136 REV A : EN-Standard Specification for Flexible Low Permeance Vapor Retarders for Thermal Insulation
  • ASTM C1137 : EN-Standard Test Method for Degradation of Fine Aggregate Due to Attrition
  • ASTM C1138 : EN-Standard Test Method for Abrasion Resistance of Concrete (Underwater Method)
  • ASTM C1138M : EN-Standard Test Method for Abrasion Resistance of Concrete (Underwater Method)
  • ASTM C1139 : EN-Standard Specification for Fibrous Glass Thermal Insulation and Sound Absorbing Blanket and Board for Military Applications
  • ASTM C114 : EN-Standard Test Methods for Chemical Analysis of Hydraulic Cement
  • ASTM C114 REV A : EN-Standard Test Methods for Chemical Analysis of Hydraulic Cement
  • ASTM C114 REV B : EN-Standard Test Methods for Chemical Analysis of Hydraulic Cement
  • ASTM C1140 : EN-Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels
  • ASTM C1140 REV A : EN-Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels
  • ASTM C1141 : EN-Standard Specification for Admixtures for Shotcrete
  • ASTM C1141/C1141M : EN-Standard Specification for Admixtures for Shotcrete
  • ASTM C1142 : EN-Standard Specification for Extended Life Mortar for Unit Masonry
  • ASTM C1143 : EN-Standard Specification for Helium for Use as a Cover Gas for Liquid Sodium
  • ASTM C1144 : EN-Standard Test Method for Splitting Tensile Strength for Brittle Nuclear Waste Forms
  • ASTM C1145 : EN-Standard Terminology of Advanced Ceramics
  • ASTM C1145 REV A : EN-STANDARD TERMINOLOGY OF ADVANCED CERAMICS
  • ASTM C1145 REV B : EN-STANDARD TERMINOLOGY OF ADVANCED CERAMICS
  • ASTM C1145 REV C : EN-STANDARD TERMINOLOGY OF ADVANCED CERAMICS
  • ASTM C1146 : EN-STANDARD GUIDE FOR PREFABRICATED PANEL INSULATION SYSTEMS FOR DUCTS AND EQUIPMENT OPERATING AT TEMPERATURES ABOVE AMBIENT AIR
  • ASTM C1147 : EN-Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics
  • ASTM C1148 : EN-STANDARD TEST METHOD FOR MEASURING THE DRYING SHRINKAGE OF MASONRY MORTAR
  • ASTM C1148 REV A : EN-Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar
  • ASTM C1149 : EN-Standard Specification for Self-Supported Spray Applied Cellulosic Thermal/Acoustical Insulation
  • ASTM C115 : EN-STANDARD TEST METHOD FOR FINENESS OF PORTLAND CEMENT BY THE TURBIDIMETER
  • ASTM C115 REV A : EN-Standard Test Method for Fineness of Portland Cement by the Turbidimeter
  • ASTM C115 REV B : EN-STANDARD TEST METHOD FOR FINENESS OF PORTLAND CEMENT BY THE TURBIDIMETER
  • ASTM C1150 : EN-STANDARD TEST METHOD FOR THE BREAK-OFF NUMBER OF CONCRETE (E1 – 1992)
  • ASTM C1151 : EN-Standard Test Method for Evaluating the Effectiveness of Materials for Curing Concrete
  • ASTM C1152 : EN-Standard Test Method for Acid-Soluble Chloride in Mortar and Concrete
  • ASTM C1152/C1152M : EN-Standard Test Method for Acid-Soluble Chloride in Mortar and Concrete
  • ASTM C1153 : EN-Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging
  • ASTM C1154 : EN-STANDARD TERMINOLOGY FOR ASBESTOS AND FIBRE CEMENT
  • ASTM C1154 REV D : EN-Standard Terminology for Non-Asbestos Fiber-Reinforced Cement Products
  • ASTM C1155 : EN-STANDARD PRACTICE FOR DETERMINING THERMAL RESISTANCE OF BUILDING ENVELOPE COMPONENTS FROM IN-SITU DATA (E1-1991)
  • ASTM C1156 : EN-STANDARD GUIDE FOR ESTABLISHING CALIBRATION FOR A MEASUREMENT METHOD USED TO ANALYZE NUCLEAR FUEL CYCLE MATERIALS
  • ASTM C1157 : EN-Standard Performance Specification for Hydraulic Cement
  • ASTM C1157 REV A : EN-Standard Performance Specification for Hydraulic Cement
  • ASTM C1157/C1157M : EN-Standard Performance Specification for Hydraulic Cement
  • ASTM C1157M : EN-STANDARD PERFORMANCE SPECIFICATION FOR BLENDED HYDRAULIC CEMENT
  • ASTM C1157M REV A : EN-Standard Performance Specification for Blended Hydraulic Cement (Metric)
  • ASTM C1157M REV B : EN-STANDARD PERFORMANCE SPECIFICATION FOR BLENDED HYDRAULIC CEMENT
  • ASTM C1158 : EN-Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Building Construction
  • ASTM C1159 : EN-Standard Specification for Sulfur Polymer Cement and Sulfur Modifier for Use in Chemical-Resistant Rigid Sulfur Concrete
  • ASTM C116 : EN-STANDARD TEST METHOD FOR COMPRESSIVE STRENGTH OF CONCRETE USING PORTIONS OF BEAMS BROKEN IN FLEXURE (AASHTO NO. T 140)
  • ASTM C1160 : EN-Standard Specification for Chemical Resistant Carbon Brick
  • ASTM C1161 : EN-STANDARD TEST METHOD FOR FLEXURAL STRENGTH OF ADVANCED CERAMICS AT AMBIENT TEMPERATURE
  • ASTM C1161 REV A : EN-Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
  • ASTM C1161 REV B : EN-Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
  • ASTM C1161 REV C : EN-Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
  • ASTM C1162 : EN-Standard Test Method for Loose Density of Asbestos
  • ASTM C1162/C1162M : EN-Standard Test Method for Loose Density of Asbestos
  • ASTM C1163 : EN-STANDARD TEST METHOD FOR MOUNTING ACTINIDES FOR ALPHA SPECTROMETRY USING NEODYMIUM FLUORIDE
  • ASTM C1164 : EN-Standard Practice for Evaluation of Limestone or Lime Uniformity From a Single Source
  • ASTM C1165 : EN-Standard Test Method for Determining Plutonium by Controlled-Potential Coulometry in H2SO4 at a Platinum Working Electrode
  • ASTM C1166 : EN-Standard Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories
  • ASTM C1167 : EN-STANDARD SPECIFICATION FOR CLAY ROOF TILES
  • ASTM C1167 REV A : EN-STANDARD SPECIFICATION FOR CLAY ROOF TILES
  • ASTM C1167 REV B : EN-STANDARD SPECIFICATION FOR CLAY ROOF TILES
  • ASTM C1168 : EN-Standard Practice for Preparation and Dissolution of Plutonium Materials for Analysis
  • ASTM C1169 : EN-Standard Guide for Laboratory Evaluation of Automatic Pedestrian SNM Monitor Performance
  • ASTM C117 : EN-Standard Test Method for Materials Finer Than 75-Micrometers (No. 200) Sieve in Mineral Aggregates by Washing
  • ASTM C1170 : EN-Standard Test Methods for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table
  • ASTM C1170/C1170M : EN-Standard Test Method for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table
  • ASTM C1171 : EN-Standard Test Method for Quantitatively Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories
  • ASTM C1172 : EN-Standard Specification for Laminated Architectural Flat Glass
  • ASTM C1173 : EN-STANDARD SPECIFICATIONS FOR FLEXIBLE TRANSITION COUPLINGS FOR UNDERGROUND PIPING SYSTEMS
  • ASTM C1173 REV A : EN-STANDARD SPECIFICATIONS FOR FLEXIBLE TRANSITION COUPLINGS FOR UNDERGROUND PIPING SYSTEMS
  • ASTM C1174 : EN-Standard Practice for Prediction of the Long-Term Behavior of Materials Including Waste Forms Used in Engineered Barrier Systems (EBS) for Geological Disposal of High-Level Radioactive Waste
  • ASTM C1175 : EN-STANDARD GUIDE TO TEST METHODS AND STANDARDS FOR NONDESTRUCTIVE TESTING OF ADVANCED CERAMICS
  • ASTM C1175 REV A : EN-Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics
  • ASTM C1176 : EN-Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table
  • ASTM C1176/C1176M : EN-Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table
  • ASTM C1177 : EN-Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
  • ASTM C1177/C1177M : EN-Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
  • ASTM C1178 : EN-Standard Specification for Glass Mat Water- Resistant Gypsum Backing Board
  • ASTM C1178/C1178M : EN-Standard Specification for Glass Mat Water-Resistant Gypsum Backing Panel
  • ASTM C1179 : EN-Standard Test Method for Oxidation Mass Loss of Manufactured Carbon and Graphite Materials in Air
  • ASTM C118 : EN-Standard Specification for Concrete Pipe for Irrigation or Drainage
  • ASTM C118 REV A : EN-Standard Specification for Concrete Pipe for Irrigation or Drainage
  • ASTM C1180 : EN-Standard Terminology of Mortar and Grout for Unit Masonry
  • ASTM C1180 REV A : EN-Standard Terminology of Mortar and Grout for Unit Masonry
  • ASTM C1181 : EN-Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts
  • ASTM C1182 : EN-Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation
  • ASTM C1183 : EN-Standard Test Method for Extrusion Rate of Elastomeric Sealants
  • ASTM C1184 : EN-Standard Specification for Structural Silicone Sealants
  • ASTM C1184 REV A : EN-Standard Specification for Structural Silicone Sealants
  • ASTM C1185 : EN-STANDARD TEST METHODS FOR SAMPLING AND TESTING NON-ASBESTOS FIBER- CEMENT FLAT SHEET ROOFING AND SIDING SHINGLES AND CLAPBOARDS
  • ASTM C1185 REV A : EN-STANDARD TEST METHODS FOR SAMPLING AND TESTING NON-ASBESTOS FIBER-CEMENT FLAT SHEET ROOFING AND SIDING SHINGLES AND CLAPBOARDS
  • ASTM C1186 : EN-Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets
  • ASTM C1186 REV A : EN-Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets
  • ASTM C1187 : EN-Standard Guide for Establishing Surveillance Test Program for Boron-Based Neutron Absorbing Material Systems for Use in Nuclear Spent Fuel Storage Racks
  • ASTM C1188 : EN-Standard Guide for Establishing a Quality Assurance Program for Uranium Conversion Facilities
  • ASTM C1189 : EN-Standard Guide to Procedures for Calibrating Automatic Pedestrian SNM Monitors
  • ASTM C118M : EN-STANDARD SPECIFICATION FOR CONCRETE PIPE FOR IRRIGATION OR DRAINAGE (METRIC)
  • ASTM C118M REV A : EN-Standard Specification for Concrete Pipe for Irrigation or Drainage [Metric]
  • ASTM C119 : EN-STANDARD TERMINOLOGY RELATING TO DIMENSION STONE
  • ASTM C119 REV A : EN-STANDARD TERMINOLOGY RELATING TO DIMENSION STONE
  • ASTM C119 REV B : EN-Standard Terminology Relating to Dimension Stone
  • ASTM C119 REV C : EN-Standard Terminology Relating to Dimension Stone
  • ASTM C119 REV D : EN-STANDARD TERMINOLOGY RELATING TO DIMENSION STONE
  • ASTM C1190 : EN-Standard Practice for Location of Test Specimens from Magnesia-Carbon and Impregnated Burned Basic Brick
  • ASTM C1191 : EN-Standard Practice for Safe Use and Handling of Ceramic Clays and Slips
  • ASTM C1192 : EN-Standard Practice for Safe Spraying of Ceramic Glazes
  • ASTM C1193 : EN-Standard Guide for Use of Joint Sealants
  • ASTM C1193 REV A : EN-Standard Guide for Use of Joint Sealants
  • ASTM C1194 : EN-Standard Test Method for Compressive Strength of Architectural Cast Stone
  • ASTM C1195 : EN-Standard Test Method for Absorption of Architectural Cast Stone
  • ASTM C1196 : EN-Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements
  • ASTM C1197 : EN-Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method
  • ASTM C1198 : EN-Standard Test Method for Dynamic Young´s Modulus Shear Modulus and Poisson´s Ratio for Advanced Ceramics by Sonic Resonance
  • ASTM C1199 : EN-Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods
  • ASTM C12 : EN-Standard Practice for Installing Vitrified Clay Pipe Lines
  • ASTM C120 : EN-Standard Test Methods of Flexure Testing of Slate (Modulus of Rupture Modulus of Elasticity)
  • ASTM C120/C120M : EN-Standard Test Methods of Flexure Testing of Slate (Breaking Load Modulus of Rupture Modulus of Elasticity)
  • ASTM C1201 : EN-Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference
  • ASTM C1201/C1201M : EN-Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference
  • ASTM C1202 : EN-Standard Test Method for Electrical Indication of Concrete-s Ability to Resist Chloride Ion Penetration
  • ASTM C1203 : EN-Standard Test Method for Quantitative Determination of Alkali Resistance of a Ceramic-Glass Enamel
  • ASTM C1204 : EN-Standard Test Method for Uranium in Presence of Plutonium by Iron(II) Reduction in Phosphoric Acid Followed by Chromium(VI) Titration
  • ASTM C1205 : EN-Standard Test Method for the Radiochemical Determination of Americium-241 in Soil by Alpha Spectrometry
  • ASTM C1206 : EN-Standard Test Method for Plutonium by Iron (II)/Chromium (VI) Amperometric Titration
  • ASTM C1207 : EN-Standard Test Method for Nondestructive Assay of Plutonium in Scrap and Waste by Passive Neutron Coincidence Counting
  • ASTM C1208 : EN-Standard Specification for Vitrified Clay Pipe and Joints for Use in Jacking Sliplining and Tunnels
  • ASTM C1208/C1208M : EN-Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling Sliplining Pipe Bursting and Tunnels
  • ASTM C1208/C1208M REV A : EN-Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling Sliplining Pipe Bursting and Tunnels
  • ASTM C1208M : EN-STANDARD SPECIFICATION FOR VITRIFIED CLAY PIPE AND JOINTS FOR USE IN JACKING SLIPLINING AND IN TUNNELS (METRIC)
  • ASTM C1209 : EN-Standard Terminology of Concrete Masonry Units and Related Units
  • ASTM C1209 REV A : EN-Standard Terminology of Concrete Masonry Units and Related Units
  • ASTM C121 : EN-Standard Test Method for Water Absorption of Slate
  • ASTM C121/C121M : EN-Standard Test Method for Water Absorption of Slate
  • ASTM C1210 : EN-Standard Guide for Establishing a Measurement System Quality Control Program for Analytical Chemistry Laboratories within the Nuclear Industry
  • ASTM C1211 : EN-Standard Test Method for Flexural Strength of Advanced Ceramics at Elevated Temperatures
  • ASTM C1211 REV A : EN-Standard Test Method for Flexural Strength of Advanced Ceramics at Elevated Temperatures
  • ASTM C1212 : EN-Standard Practice for Fabricating Ceramic Reference Specimens Containing Seeded Voids
  • ASTM C1213 : EN-Standard Terminology Relating to Precast Concrete Products
  • ASTM C1214 : EN-Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method
  • ASTM C1214M : EN-Standard Test Method for Concrete Pipe Sewerlines by Negative Air Pressure (Vacuum) Test Method (Metric)
  • ASTM C1215 : EN-Standard Guide for Preparing and Interpreting Precision and Bias Statements in Test Method Standards Used in the Nuclear Industry
  • ASTM C1216 : EN-Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants
  • ASTM C1217 : EN-Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials
  • ASTM C1218 : EN-Standard Test Method for Water-Soluble Chloride in Mortar and Concrete
  • ASTM C1218/C1218M : EN-Standard Test Method for Water-Soluble Chloride in Mortar and Concrete
  • ASTM C1219 : EN-Standard Test Methods for Arsenic in Uranium Hexafluoride
  • ASTM C122 : EN-STANDARD METHOD OF PANEL SPALLING TESTING SUPER- DUTY FIRECLAY BRICK (R 1984)
  • ASTM C1220 : EN-Standard Test Method for Static Leaching of Monolithic Waste Forms for Disposal of Radioactive Waste
  • ASTM C1221 : EN-Standard Test Method for Nondestructive Analysis of Special Nuclear Materials in Homogeneous Solutions by Gamma-Ray Spectrometry
  • ASTM C1222 : EN-Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement
  • ASTM C1222 REV A : EN-STANDARD PRACTICE FOR EVALUATION OF LABORATORIES TESTING HYDRAULIC CEMENT
  • ASTM C1222 REV B : EN-STANDARD PRACTICE FOR EVALUATION OF LABORATORIES TESTING HYDRAULIC CEMENT
  • ASTM C1223 : EN-Standard Test Method for Testing of Glass Exudation from AZS Fusion-Cast Refractories
  • ASTM C1224 : EN-Standard Specification for Reflective Insulation for Building Applications
  • ASTM C1225 : EN-Standard Specification for Non-Asbestos Fiber- Cement Roofing Shingles Shakes and Slates
  • ASTM C1226 : EN-Standard Test Method for Soluble Chlorides in Asbestos
  • ASTM C1227 : EN-Standard Specification for Precast Concrete Septic Tanks
  • ASTM C1227 REV A : EN-STANDARD SPECIFICATION FOR PRECAST CONCRETE SEPTIC TANKS
  • ASTM C1227 REV B : EN-Standard Specification for Precast Concrete Septic Tanks
  • ASTM C1227 REV C : EN-Standard Specification for Precast Concrete Septic Tanks
  • ASTM C1228 : EN-Standard Practice for Preparing Coupons for Flexural and Washout Tests on Glass Fiber Reinforced Concrete
  • ASTM C1229 : EN-STANDARD TEST METHOD FOR DETERMINATION OF GLASS- FIBER CONTENT IN GLASS FIBER REINFORCED CONCRETE (GFRC) (WASH- OUT TEST)
  • ASTM C123 : EN-STANDARD TEST METHOD FOR LIGHTWEIGHT PIECES IN AGGREGATE (AASHTO NO. T113) (R-1990) (E1-1990)
  • ASTM C1230 : EN-Standard Test Method for Performing Tension Tests on Glass-Fiber Reinforced Concrete (GFRC) Bonding Pads
  • ASTM C1230 REV A : EN-STANDARD TEST METHOD FOR PERFORMING TENSION TESTS ON GLASS-FIBER REINFORCED CONCRETE (GFRC) BONDING PADS
  • ASTM C1231 : EN-Standard Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders
  • ASTM C1231/C1231M : EN-Standard Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders
  • ASTM C1231/C1231M REV A : EN-Standard Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders
  • ASTM C1232 : EN-Standard Terminology of Masonry
  • ASTM C1232 REV A : EN-Standard Terminology of Masonry
  • ASTM C1232 REV B : EN-Standard Terminology of Masonry
  • ASTM C1233 : EN-Standard Practice for Determining Equivalent Boron Contents of Nuclear Materials
  • ASTM C1234 : EN-Standard Practice for Preparation of Oils and Oily Waste Samples by High-Pressure High-Temperature Digestion for Trace Element Determinations
  • ASTM C1235 : EN-STANDARD TEST METHOD FOR PLUTONIUM BY TITANIUM (III)/CERIUM(IV) TITRATION
  • ASTM C1235 REV A : EN-Standard Test Method for Plutonium by Titanium(III)/Cerium(IV) Titration
  • ASTM C1236 : EN-Standard Guide for In-Plant Performance Evaluation of Automatic Vehicle SNM Monitors
  • ASTM C1237 : EN-Standard Guide to In-Plant Performance Evaluation of Hand-Held SNM Monitors
  • ASTM C1238 : EN-Standard Guide for Installation of Walk- Through Metal Detectors
  • ASTM C1239 : EN-Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
  • ASTM C1239 REV A : EN-Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
  • ASTM C1240 : EN-Standard Specification for Use of Silica Fume as a Mineral Admixture in Hydraulic- Cement Concrete Mortar and Grout
  • ASTM C1240 REV A : EN-Standard Specification for Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete Mortar and Grout
  • ASTM C1240 REV B : EN-Standard Specification for Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete Mortar and Grout
  • ASTM C1241 : EN-Standard Test Method for Volume Shrinkage of Latex Sealants During Cure
  • ASTM C1242 : EN-Standard Guide for Selection Design and Installation of Dimension Stone Anchoring Systems
  • ASTM C1242 REV A : EN-Standard Guide for Selection Design and Installation of Dimension Stone Anchoring Systems
  • ASTM C1242 REV B : EN-Standard Guide for Design Selection and Installation of Exterior Dimension Stone Anchors and Anchoring Systems
  • ASTM C1243 : EN-Standard Test Method for Relative Resistance to Deep Abrasive Wear of Unglazed Ceramic Tile by Rotating Disc
  • ASTM C1244 : EN-Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill
  • ASTM C1244 REV A : EN-Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill
  • ASTM C1244M : EN-Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill [Metric]
  • ASTM C1244M REV A : EN-Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill [Metric]
  • ASTM C1245 : EN-Standard Test Method for Determining Bond Strength between Hardened Roller Compacted Concrete and Other Hardened Cementitious Mixtures Point Load Test
  • ASTM C1245/C1245M : EN-Standard Test Method for Determining Bond Strength between Hardened Roller Compacted Concrete and Other Hardened Cementitious Mixtures (Point Load Test)
  • ASTM C1246 : EN-Standard Test Method for Effects of Heat Aging on Weight Loss Cracking and Chalking of Elastomeric Sealants After Cure
  • ASTM C1247 : EN-Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids
  • ASTM C1248 : EN-Standard Test Method for Staining of Porous Substrate by Joint Sealants
  • ASTM C1249 : EN-Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
  • ASTM C1249 REV A : EN-Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
  • ASTM C125 : EN-Standard Terminology Relating to Concrete and Concrete Aggregates
  • ASTM C125 REV A : EN-Standard Terminology Relating to Concrete and Concrete Aggregates
  • ASTM C1250 : EN-Standard Test Method for Nonvolatile Content of Cold Liquid-Applied Elastomeric Waterproofing Membranes
  • ASTM C1251 : EN-Standard Guide for Determination of Specific Surface Area of Advanced Ceramic Materials by Gas Adsorption
  • ASTM C1252 : EN-Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape Surface Texture and Grading
  • ASTM C1253 : EN-Standard Test Method for Determining the Outgassing Potential of Sealant Backing
  • ASTM C1254 : EN-Standard Test Method for Determination of Uranium in Mineral Acids by X-Ray Fluorescence
  • ASTM C1255 : EN-Standard Test Method for Analysis of Uranium and Thorium in Soils by Energy Dispersive X-Ray Fluorescence Spectroscopy
  • ASTM C1256 : EN-Standard Practice for Interpreting Glass Fracture Surface Features
  • ASTM C1257 : EN-Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants
  • ASTM C1257 REV A : EN-Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants
  • ASTM C1258 : EN-Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
  • ASTM C1259 : EN-STANDARD TEST METHOD FOR DYNAMIC YOUNG´S MODULUS SHEAR MODULUS AND POISSON´S RATIO FOR ADVANCED CERAMICS BY IMPULSE EXCITATION OF VIBRATION
  • ASTM C126 : EN-STANDARD SPECIFICATION FOR CERAMIC GLAZED STRUCTURAL CLAY FACING TILE FACING BRICK AND SOLID MASONRY UNITS
  • ASTM C1260 : EN-Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method)
  • ASTM C1260 REV A : EN-Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method)
  • ASTM C1261 : EN-STANDARD SPECIFICATION FOR FIREBOX BRICK FOR RESIDENTIAL FIREPLACES
  • ASTM C1262 : EN-Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
  • ASTM C1262 REV A : EN-Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
  • ASTM C1263 : EN-Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders
  • ASTM C1264 : EN-Standard Specification for Sampling Inspection Rejection Certification Packaging Marking Shipping Handling and Storage of Gypsum Board
  • ASTM C1264/C1264M : EN-Standard Specification for Sampling Inspection Rejection Certification Packaging Marking Shipping Handling and Storage of Gypsum Board
  • ASTM C1265 : EN-Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
  • ASTM C1266 : EN-STANDARD TEST METHOD FOR FLOW CHARACTERISTICS OF PREFORMED TAPE SEALANTS
  • ASTM C1267 : EN-Standard Test Method for Uranium by Iron (II) Reduction in Phosphoric Acid Followed by Chromium (VI) Titration in the Presence of Vanadium
  • ASTM C1268 : EN-Standard Test Method for Quantitative Determination of American 241 in Plutonium by Gamma-Ray Spectrometry
  • ASTM C1269 : EN-Standard Practice for Adjusting the Operational Sensitivity Setting of in-Plant Walk-Through Metal Detectors
  • ASTM C127 : EN-Standard Test Method for Specific Gravity and Absorption of Coarse Aggregate-AASHTO T85; E1-1993
  • ASTM C1270 : EN-Standard Practice for Detection Sensitivity Mapping of In-Plant Walk-Through Metal Detectors
  • ASTM C1271 : EN-Standard Test Method for X-Ray Spectrometric Analysis of Lime and Limestone
  • ASTM C1271 REV A : EN-Standard Test Method for X-Ray Spectrometric Analysis of Lime and Limestone
  • ASTM C1272 : EN-Standard Specification for Heavy Vehicular Paving Brick
  • ASTM C1272 REV A : EN-Standard Specification for Heavy Vehicular Paving Brick
  • ASTM C1273 : EN-STANDARD PRACTICE FOR TENSILE STRENGTH OF MONOLITHIC ADVANCED CERAMICS AT AMBIENT TEMPERATURES
  • ASTM C1273 REV A : EN-Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures
  • ASTM C1274 : EN-Standard Test Method for Advanced Ceramic Specific Surface Area by Physical Adsorption
  • ASTM C1275 : EN-Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Test Specimens at Ambient Temperature
  • ASTM C1276 : EN-Standard Test Method for Measuring the Viscosity of Mold Powders Above Their Melting Point Using a Rotational Viscometer
  • ASTM C1277 : EN-Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
  • ASTM C1277 REV A : EN-Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
  • ASTM C1278 : EN-STANDARD SPECIFICATION FOR FIBER-REINFORCED GYPSUM PANELS
  • ASTM C1278/C1278M : EN-Standard Specification for Fiber-Reinforced Gypsum Panel
  • ASTM C1278/C1278M REV A : EN-Standard Specification for Fiber-Reinforced Gypsum Panel
  • ASTM C1279 : EN-Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed Heat-Strengthened and Fully Tempered Flat Glass
  • ASTM C128 : EN-Standard Test Method for Density Relative Density (Specific Gravity) and Absorption of Fine Aggregate
  • ASTM C128 REV A : EN-Standard Test Method for Density Relative Density (Specific Gravity) and Absorption of Fine Aggregate
  • ASTM C1280 : EN-Standard Specification for Application of Gypsum Sheathing Board
  • ASTM C1281 : EN-Standard Specification for Preformed Tape Sealants for Glazing Applications
  • ASTM C1282 : EN-Standard Test Method for Determining the Particle Size Distribution of Advanced Ceramics by Centrifugal Photosedimentation
  • ASTM C1283 : EN-Standard Practice for Installing Clay Flue Lining
  • ASTM C1283 REV A : EN-Standard Practice for Installing Clay Flue Lining
  • ASTM C1284 : EN-Standard Practice for Electrodeposition of the Actinides for Alpha Spectrometry
  • ASTM C1285 : EN-Standard Test Methods for Determining Chemical Durability of Nuclear Waste Glasses: the Product Consistency Test (PCT)
  • ASTM C1286 : EN-Standard Classification for Advanced Ceramics
  • ASTM C1287 : EN-STANDARD TEST METHOD FOR DETERMINATION OF IMPURITIES IN URANIUM DIOXIDE BY INDUCTIVELY COUPLED PLASMA MASS SPECTROMETRY
  • ASTM C1288 : EN-Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets
  • ASTM C1289 : EN-Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
  • ASTM C1289 REV A : EN-Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
  • ASTM C129 : EN-Standard Specification for Nonloadbearing Concrete Masonry Units
  • ASTM C129 REV A : EN-STANDARD SPECIFICATION FOR NONLOADBEARING CONCRETE MASONRY UNITS
  • ASTM C1290 : EN-Standard Specification for Flexible Fibrous Glass Blanket Insulation Used to Externally Insulate HVAC Ducts-E1
  • ASTM C1291 : EN-Standard Test Method for Elevated Temperature Tensile Creep Strain Creep Strain Rate and Creep Time-To-Failure for Advanced Monolithic Ceramics
  • ASTM C1291 REV A : EN-Standard Test Method for Elevated Temperature Tensile Creep Strain Creep Strain Rate and Creep Time-To-Failure for Advanced Monolithic Ceramics
  • ASTM C1292 : EN-STANDARD TEST METHODS FOR SHEAR STRENGTH OF CONTINUOUS FIBER-REINFORCED ADVANCED CERAMICS AT AMBIENT TEMPERATURES
  • ASTM C1292 REV A : EN-Standard Test Methods for Shear Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures
  • ASTM C1293 : EN-Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
  • ASTM C1293 REV A : EN-Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
  • ASTM C1293 REV B : EN-Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
  • ASTM C1294 : EN-Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
  • ASTM C1295 : EN-Standard Test Method for Gamma Energy Emission from Fission Products in Uranium Hexafluoride
  • ASTM C1296 : EN-Standard Test Method for Determination of Sulfur in Uranium Oxides and Uranyl Nitrate Solutions by X-Ray Fluorescence (XRF)
  • ASTM C1297 : EN-Standard Guide for Qualification of Laboratory Analysts for the Analysis of Nuclear Fuel Cycle Materials
  • ASTM C1298 : EN-Standard Guide for Design and Construction of Brick Liners for Industrial Chimneys
  • ASTM C1299 : EN-Standard Guide for Use in Selection of Liquid-Applied Sealants
  • ASTM C1300 : EN-Standard Test Method for Linear Thermal Expansion of Glaze Frits and Ceramic Whiteware Materials by the Interferometric Method
  • ASTM C1301 : EN-Standard Test Method for Major and Trace Elements in Limestone and Lime by Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP) and Atomic Absorption (AA)
  • ASTM C1302 : EN-Standard Guide for Selection and Use of Keywords for Thermal Insulation Test Methods and Standards
  • ASTM C1303 : EN-Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation
  • ASTM C1303 REV A : EN-Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation
  • ASTM C1303/C1303M : EN-Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation
  • ASTM C1304 : EN-Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials
  • ASTM C1305 : EN-Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane
  • ASTM C1306 : EN-Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane
  • ASTM C1306 REV A : EN-Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane
  • ASTM C1307 : EN-Standard Test Method for Plutonium Assay by Plutonium (III) Diode Array Spectrophotometry
  • ASTM C1308 : EN-Standard Test Method for Accelerated Leach Test for Diffusive Releases from Solidified Waste and a Computer Program to Model Diffusive Fractional Leaching from Cylindrical Waste Forms
  • ASTM C1309 : EN-Standard Practice for Performance Evaluation of In-Plant Walk-Through Metal Detectors
  • ASTM C131 : EN-Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
  • ASTM C1310 : EN-Standard Test Method for Determining Radionuclides in Soils by Inductively Coupled Plasma-Mass Spectrometry Using Flow Injection Preconcentration
  • ASTM C1311 : EN-Standard Specification for Solvent Release Sealants
  • ASTM C1312 : EN-Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory
  • ASTM C1313 : EN-Standard Specification for Sheet Radiant Barriers for Building Construction Applications
  • ASTM C1313/C1313M : EN-Standard Specification for Sheet Radiant Barriers for Building Construction Applications
  • ASTM C1314 : EN-Standard Test Method for Compressive Strength of Masonry Prisms
  • ASTM C1314 REV A : EN-Standard Test Method for Compressive Strength of Masonry Prisms
  • ASTM C1314 REV B : EN-Standard Test Method for Compressive Strength of Masonry Prisms
  • ASTM C1315 : EN-Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete
  • ASTM C1316 : EN-Standard Test Method for Nondestructive Assay of Nuclear Material in Scrap and Waste by Passive-Active Neutron Counting Using a 252Cf Shuffler
  • ASTM C1317 : EN-Standard Practice for Dissolution of Silicate or Acid-Resistant Matrix Samples
  • ASTM C1318 : EN-Standard Test Method for Determination of Total Neutralizing Capability and Dissolved Calcium and Magnesium Oxide in Lime for Flue Gas Desulfurization (FGD)
  • ASTM C1319 : EN-Standard Specification for Concrete Grid Paving Units
  • ASTM C1320 : EN-Standard Practice for Installation of Mineral Fiber Batt and Blanket Thermal Insulation for Light Frame Construction
  • ASTM C1321 : EN-Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction
  • ASTM C1322 : EN-Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
  • ASTM C1322 REV A : EN-Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
  • ASTM C1322 REV B : EN-Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
  • ASTM C1323 : EN-Standard Test Method for Ultimate Strength of Advanced Ceramics with Diametrally Compressed C-Ring Specimens at Ambient Temperature
  • ASTM C1324 : EN-Standard Test Method for Examination and Analysis of Hardened Masonry Mortar
  • ASTM C1324 REV A : EN-Standard Test Method for Examination and Analysis of Hardened Masonry Mortar
  • ASTM C1325 : EN-Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cement Interior Substrate Sheets
  • ASTM C1325 REV A : EN-Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units
  • ASTM C1325 REV B : EN-Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units
  • ASTM C1326 : EN-Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics
  • ASTM C1326 REV A : EN-Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics
  • ASTM C1327 : EN-Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics
  • ASTM C1327 REV A : EN-Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics
  • ASTM C1328 : EN-Standard Specification for Plastic (Stucco) Cement
  • ASTM C1328 REV A : EN-Standard Specification for Plastic (Stucco) Cement
  • ASTM C1329 : EN-Standard Specification for Mortar Cement
  • ASTM C1329 REV A : EN-Standard Specification for Mortar Cement
  • ASTM C133 : EN-Standard Test Methods for Cold Crushing Strength and Modulus of Rupture of Refractories
  • ASTM C1330 : EN-Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants
  • ASTM C1331 : EN-Standard Test Method for Measuring Ultrasonic Velocity in Advanced Ceramics with Broadband Pulse-Echo Cross-Correlation Method
  • ASTM C1332 : EN-Standard Test Method for Measurement of Ultrasonic Attenuation Coefficients of Advanced Ceramics by Pulse-Echo Contact Technique
  • ASTM C1334 : EN-Standard Specification for Uranium Oxides with a 235 U Content of Less Than 5 % for Dissolution Prior to Conversion to Nuclear-Grade Uranium Dioxide
  • ASTM C1335 : EN-Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation
  • ASTM C1336 : EN-Standard Practice for Fabrication Non-Oxide Ceramic Reference Specimens Containing Seeded Inclusions
  • ASTM C1337 : EN-Standard Test Method for Creep and Creep Rupture of Continuous Fiber-Reinforced Ceramic Composites under Tensile Loading at Elevated Temperatures
  • ASTM C1338 : EN-Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
  • ASTM C1339 : EN-Standard Test Method for Flowability and Bearing Area of Chemical-Resistant Polymer Machinery Grouts
  • ASTM C1339 REV A : EN-Standard Test Method for Flowability and Bearing Area of Chemical-Resistant Polymer Machinery Grouts
  • ASTM C134 : EN-STANDARD TEST METHODS FOR SIZE DIMENSIONAL MEASUREMENTS AND BULK DENSITY OF REFRACTORY BRICK AND INSULATING FIREBRICK
  • ASTM C1340 : EN-Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program
  • ASTM C1340/C1340M : EN-Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program
  • ASTM C1341 : EN-Standard Test Method for Flexural Properties of Continuous Fiber- Reinforced Advanced Ceramic Composites
  • ASTM C1342 : EN-Standard Practice for Flux Fusion Sample Dissolution
  • ASTM C1343 : EN-Standard Test Method for Determination of Low Concentrations of Uranium in Oils and Organic Liquids by X-Ray Fluorescence
  • ASTM C1344 : EN-Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Mass Spectrometer Method
  • ASTM C1345 : EN-Standard Test Method for Analysis of Total and Isotopic Uranium and Total Thorium in Soils by Inductively Coupled Plasma-Mass Spectrometry
  • ASTM C1346 : EN-Standard Practice for Dissolution of UF6 from P-10 Tubes
  • ASTM C1347 : EN-Standard Practice for Preparation and Dissolution of Uranium Materials for Analysis
  • ASTM C1347 REV A : EN-Standard Practice for Preparation and Dissolution of Uranium Materials for Analysis
  • ASTM C1348 : EN-Standard Specification for Blended Uranium Oxides with a 235U Content of Less Than 5 % for Direct Hydrogen Reduction to Nuclear Grade Uranium Dioxide
  • ASTM C1349 : EN-Standard Specification for Architectural Flat Glass Clad Polycarbonate
  • ASTM C135 : EN-Standard Test Method for True Specific Gravity of Refractory Materials by Water Immersion
  • ASTM C1350M : EN-Standard Test Method for Measurement of Viscosity of Glass Between Softening Point and Annealing Range (Approximately 108 Pa·s to Approximately 1013 Pa·s) by Beam Bending (Metric)
  • ASTM C1351M : EN-Standard Test Method for Measurement of Viscosity of Glass Between 104 Pa·s and 108 Pa·s by Viscous Compression of a Solid Right Cylinder [Metric]
  • ASTM C1352 : EN-Standard Test Method for Flexural Modulus of Elasticity of Dimension Stone
  • ASTM C1352/C1352M : EN-Standard Test Method for Flexural Modulus of Elasticity of Dimension Stone
  • ASTM C1353 : EN-Standard Test Method for Abrasion Resistance of Dimension Stone by the Taber Abraser
  • ASTM C1354 : EN-Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone
  • ASTM C1354/C1354M : EN-Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone
  • ASTM C1355/C1355M : EN-Standard Specification for Glass Fiber Reinforced Gypsum Compsites
  • ASTM C1356 : EN-Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure
  • ASTM C1356M : EN-Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure (Metric)
  • ASTM C1357 : EN-Standard Test Methods for Evaluating Masonry Bond Strength
  • ASTM C1357 REV A : EN-Standard Test Methods for Evaluating Masonry Bond Strength
  • ASTM C1358 : EN-Standard Test Method for Monotonic Compressive Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Specimens at Ambient Temperatures
  • ASTM C1359 : EN-Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Specimens at Elevated Temperatures
  • ASTM C136 : EN-Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
  • ASTM C136 REV A : EN-STANDARD METHOD FOR SIEVE ANALYSIS OF FINE AND COARSE AGGREGATES
  • ASTM C1360 : EN-Standard Practice for Constant-Amplitude Axial Tension-Tension Cyclic Fatigue of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures
  • ASTM C1361 : EN-Standard Practice for Constant-Amplitude Axial Tension-Tension Cyclic Fatigue of Advanced Ceramics at Ambient Temperatures
  • ASTM C1362 : EN-Standard Test Method for Flow of Freshly Mixed Hydraulic Cement Concrete
  • ASTM C1363 : EN-Standard Test Method for the Thermal Performance of Building Assemblies by Means of a Hot Box Apparatus
  • ASTM C1364 : EN-Standard Specification for Architectural Cast Stone
  • ASTM C1365 : EN-Standard Test Method for Determination of the Proportion of Phases in Portland Cement and Portland-Cement Clinker Using X-Ray Powder Diffraction Analysis
  • ASTM C1366 : EN-Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures
  • ASTM C1367 : EN-Standard Test Method for Heat Resistance of Hot-Applied Sealants under Dead Load Shear
  • ASTM C1368 : EN-Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Ambient Temperature
  • ASTM C1369 : EN-Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
  • ASTM C1370 : EN-Standard Test Method for Determining the Chemical Resistance of Aggregates for Use in Chemical-Resistant Sulfur Polymer Cement Concrete and Other Chemical-Resistant Polymer Concretes
  • ASTM C1371 : EN-Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
  • ASTM C1371 REV A : EN-Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
  • ASTM C1372 : EN-Standard Specification for Dry-Cast Segmental Retaining Wall Units
  • ASTM C1372 REV A : EN-Standard Specification for Segmental Retaining Wall Units
  • ASTM C1373 : EN-Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems under Simulated Winter Conditions
  • ASTM C1374 : EN-Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation
  • ASTM C1375 : EN-Standard Guide for Substrates Used in Testing Building Seals and Sealants
  • ASTM C1376 : EN-Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Glass
  • ASTM C1377 : EN-Standard Test Method for Calibration of Surface/Stress Measuring Devices
  • ASTM C1378 : EN-Standard Test Method for Determination of Resistance to Staining
  • ASTM C1379 : EN-Standard Test Method for Analysis of Urine for Uranium-235 and Uranium-238 Isotopes by Inductively Coupled Plasma-Mass Spectrometry
  • ASTM C138 : EN-STANDARD TEST METHOD FOR UNIT WEIGHT YIELD AND AIR CONTENT (GRAVIMETRIC) OF CONCRETE (AASHTO NO. T121) (E1-1983)
  • ASTM C138/C138M : EN-Standard Test Method for Density (Unit Weight) Yield and Air Content (Gravimetric) of Concrete
  • ASTM C138/C138M REV A : EN-Standard Test Method for Density (Unit Weight) Yield and Air Content (Gravimetric) of Concrete-AASHTO No.: T121
  • ASTM C1380 : EN-Standard Test Method for Determination of Uranium Content and Isotopic Composition by Isotope Dilution Mass Spectrometry
  • ASTM C1381 : EN-Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts
  • ASTM C1381/C1381M : EN-Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts
  • ASTM C1382 : EN-Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
  • ASTM C1383 : EN-Standard Test Method for Measuring the P-Wave Speed and the Thickness of Concrete Plates Using the Impact-Echo Method
  • ASTM C1383 REV A : EN-Standard Test Method for Measuring the P-Wave Speed and the Thickness of Concrete Plates Using the Impact-Echo Method
  • ASTM C1384 : EN-Standard Specification for Admixtures for Masonry Mortars
  • ASTM C1384 REV A : EN-Standard Specification for Admixtures for Masonry Mortars
  • ASTM C1385 : EN-Standard Practice for Sampling Materials for Shotcrete
  • ASTM C1385/C1385M : EN-Standard Practice for Sampling Materials for Shotcrete
  • ASTM C1386 : EN-Standard Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction Units
  • ASTM C1387 : EN-Standard Guide for the Determination of Technetium-99 in Soil
  • ASTM C1388 : EN-Standard Test Method for Compressive Strength of Laboratory Constructed Masonry Prisms
  • ASTM C1389 : EN-Standard Test Method for Water Penetration and Leakage Through Masonry
  • ASTM C139 : EN-Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes
  • ASTM C139 REV A : EN-STANDARD SPECIFICATION FOR CONCRETE MASONRY UNITS FOR CONSTRUCTION OF CATCH BASINS AND MANHOLES
  • ASTM C1390 : EN-Standard Test Methods for Flexural Bond Strength of Masonry
  • ASTM C1391 : EN-Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages
  • ASTM C1392 : EN-Standard Guide for Evaluating Failure of Structural Sealant Glazing
  • ASTM C1393 : EN-Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks
  • ASTM C1393 REV A : EN-Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks
  • ASTM C1394 : EN-Standard Guide for In-Situ Structural Silicone Glazing Evaluation
  • ASTM C1395/C1395M : EN-Specification for Gypsum Ceiling Board
  • ASTM C1396/C1396M : EN-Standard Specification for Gypsum Board
  • ASTM C1396/C1396M REV A : EN-Standard Specification for Gypsum Board
  • ASTM C1397 : EN-Standard Practice for Application of Class PB Exterior Insulation and Finish Systems
  • ASTM C1398 : EN-Standard Test Method for The Laboratory Determination of the Time of Setting of Hydraulic-Cement Mortars Containing Additives for Shotcrete by the Use of Gillmore Needles
  • ASTM C1399 : EN-Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
  • ASTM C1399 REV A : EN-Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
  • ASTM C1399/C1399M : EN-Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
  • ASTM C14 : EN-Standard Specification for Nonreinforced Concrete Sewer Storm Drain and Culvert Pipe
  • ASTM C14 REV A : EN-Standard Specification for Nonreinforced Concrete Sewer Storm Drain and Culvert Pipe
  • ASTM C140 : EN-Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
  • ASTM C140 REV A : EN-Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
  • ASTM C140 REV B : EN-Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
  • ASTM C1400 : EN-Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls
  • ASTM C1401 : EN-Standard Guide for Structural Sealant Glazing
  • ASTM C1401 REV A : EN-Standard Guide for Structural Sealant Glazing
  • ASTM C1402 : EN-Standard Guide for High-Resolution Gamma-Ray Spectrometry of Soil Samples
  • ASTM C1403 : EN-Standard Test Method for Rate of Water Absorption of Masonry Mortars
  • ASTM C1403 REV A : EN-Standard Test Method for Rate of Water Absorption of Masonry Mortars
  • ASTM C1404/C1404M : EN-Standard Test Method for Bond Strength of Adhesive Systems Used with Concrete as Measured by Direct Tension
  • ASTM C1405 : EN-Standard Specification for Glazed Brick (Single Fired Brick Units)
  • ASTM C1405 REV A : EN-Standard Specification for Glazed Brick (Single Fired Brick Units)
  • ASTM C1405 REV B : EN-Standard Specification for Glazed Brick (Single Fired Solid Brick Units)
  • ASTM C1407 : EN-Standard Practice for Calculating Areas Volume and Linear Change of Refractory Shapes
  • ASTM C1408 : EN-Standard Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets by Direct Combustion-Infrared Detection Method
  • ASTM C1409 : EN-Standard Guide for Measuring and Estimating Quantities of Insulated Piping and Components
  • ASTM C141 : EN-Standard Specification for Hydraulic Hydrated Lime for Structural Purposes
  • ASTM C141/C141M : EN-Standard Specification for Hydrated Hydraulic Lime for Structural Purposes
  • ASTM C1410 : EN-Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation
  • ASTM C1410 REV A : EN-Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation
  • ASTM C1411 : EN-Standard Practice for The Ion Exchange Separation of Uranium and Plutonium Prior to Isotopic Analysis
  • ASTM C1412 : EN-Standard Practice for Microwave Oven Dissolution of Glass Containing Radioactive and Mixed Wastes
  • ASTM C1413 : EN-Standard Test Method for Isotopic Analysis of Hydrolyzed Uranium Hexafluoride and Uranyl Nitrate Solutions by Thermal Ionization Mass Spectrometry
  • ASTM C1414 : EN-Standard Practice for the Separation of Americium from Plutonium by Ion Exchange
  • ASTM C1415 : EN-Standard Test Method for 238Pu Isotopic Abundance by Alpha Spectrometry
  • ASTM C1415 REV A : EN-Standard Test Method for 238Pu Isotopic Abundance by Alpha Spectrometry
  • ASTM C1416 : EN-Standard Test Method for Uranium Analysis Waste Water by X-ray Fluorescence
  • ASTM C1417 : EN-Standard Specification for Manufacture of Reinforced Concrete Sewer Storm Drain and Culvert Pipe for Direct Design
  • ASTM C1417M : EN-Standard Specification for Manufacture of Reinforced Concrete Sewer Storm Drain and Culvert Pipe for Direct Design [Metric]
  • ASTM C1419 : EN-Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in Obtaining an Approximate Young´s Modulus
  • ASTM C1419 REV A : EN-Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in Obtaining an Approximate Young-s Modulus
  • ASTM C142 : EN-Standard Test Method for Clay Lumps and Friable Particles in Aggregates-AASHTO No.: T112
  • ASTM C1420 : EN-Standard Practice for Selection Removal and Shipment of Manufactured Masonry Units Placed in Usage
  • ASTM C1420 REV A : EN-Standard Guide for Selection Removal and Shipment of Manufactured Masonry Units Placed in Usage
  • ASTM C1421 : EN-Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature
  • ASTM C1421 REV A : EN-Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature
  • ASTM C1421 REV B : EN-Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature
  • ASTM C1422 : EN-Standard Specification for Chemically Strengthened Flat Glass
  • ASTM C1423 : EN-Standard Guide for Selecting Jacketing Materials for Thermal Insulation
  • ASTM C1424 : EN-Standard Test Method for Monotonic Compressive Strength of Advanced Ceramics at Ambient Temperature
  • ASTM C1425 : EN-Standard Test Method for Interlaminar Shear Strength of 1-D and 2-D Continuous Fiber-Reinforced Advanced Ceramics at Elevated Temperatures
  • ASTM C1426 : EN-Standard Practices for Verification and Calibration of Polarimeters
  • ASTM C1427 : EN-Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in heet and Tubular Form
  • ASTM C1427 REV A : EN-Specification for Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form
  • ASTM C1428 : EN-Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Multiple Collector Mass Spectrometer Method
  • ASTM C1429 : EN-Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Double-Standard Multi-Collector Gas Mass Spectrometer
  • ASTM C143 : EN-STANDARD TEST METHOD FOR SLUMP OF PORTLAND CEMENT CONCRETE (E1-1985)
  • ASTM C143 REV A : EN-Standard Test Method for Slump of Hydraulic Cement Concrete-AASHTO T119
  • ASTM C143/C143M : EN-Standard Test Method for Slump of Hydraulic-Cement Concrete
  • ASTM C143/C143M REV A : EN-Standard Test Method for Slump of Hydraulic-Cement Concrete
  • ASTM C1430 : EN-Standard Test Method for Determination of Uranium Oxygen to Uranium (O/U) and Oxygen to Metal (O/M) in Sintered Uranium Dioxide and Gadolinia-Uranium Dioxide Pellets by Atmospheric Equilibration
  • ASTM C1431 : EN-Standard Guide for Corrosion Testing of Aluminum-Based Spent Nuclear Fuel in Support of Repository Disposal
  • ASTM C1432 : EN-Standard Test Method for Determination of Impurities in Plutonium: Acid Dissolution Ion Exchange Matrix Separation and Inductively Coupled Plasma-Atomic Emission Spectroscopic (ICP/AES) Analysis
  • ASTM C1433 : EN-Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts Storm Drains and Sewers
  • ASTM C1433 REV A : EN-Standard Specification for Precast Reinforced Concrete Box Sections for Culverts Storm Drains and Sewers
  • ASTM C1433M : EN-Standard Specification for Precast Reinforced Concrete Box Sections for Culverts Storm Drains and Sewers (Metric)
  • ASTM C1433M REV A : EN-Standard Specification for Precast Reinforced Concrete Box Sections for Culverts Storm Drains and Sewers (Metric)
  • ASTM C1435 : EN-Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer
  • ASTM C1435/C1435M : EN-Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer
  • ASTM C1436 : EN-Standard Specification for Materials for Shotcrete
  • ASTM C1437 : EN-Standard Test Method for Flow of Hydraulic Cement Mortar
  • ASTM C1438 : EN-Standard Specification for Latex and Powder Polymer Modifiers for Hydraulic Cement Concrete and Mortar
  • ASTM C1439 : EN-Standard Test Methods for Evaluating Polymer Modifiers in Mortar and Concrete
  • ASTM C1439 REV A : EN-Standard Test Methods for Evaluating Polymer Modifiers in Mortar and Concrete
  • ASTM C144 : EN-Standard Specification for Aggregate for Masonry Mortar-AASHTO No.: M45-70(1974)
  • ASTM C1440 : EN-Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain Waste and Vent (DWV) Sewer Sanitary and Storm Plumbing Systems
  • ASTM C1441 : EN-Standard Test Method for the Analysis of Refrigerant 114 Plus Other Carbon-Containing and Fluorine-Containing Compounds in Uranium Hexafluoride Via Fourier-Transform Infrared (FTIR) Spectroscopy
  • ASTM C1442 : EN-Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
  • ASTM C1443 : EN-Standard Specification for Glasses Portlight Circular Fully Tempered
  • ASTM C1444 : EN-Standard Test Method for Measuring the Angle of Repose of Free-Flowing Mold Powders
  • ASTM C1445 : EN-Standard Test Method for Measuring Consistency of Castable Refractory Using a Flow Table
  • ASTM C1446 : EN-Standard Test Method for Measuring Consistency and Working Time of Self-Flowing Castable Refractories
  • ASTM C1447 : EN-Standard Specification for Non-Asbestos Fiber-Cement Underdrain Pipe
  • ASTM C1447/C1447M : EN-Standard Specification for Non-Asbestos Fiber-Cement Underdrain Pipe
  • ASTM C1448 : EN-Standard Specification for Non-Asbestos Fiber-Cement Conduit
  • ASTM C1448/C1448M : EN-Standard Specification for Non-Asbestos Fiber-Cement Conduit
  • ASTM C1449 : EN-Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe
  • ASTM C1449/C1449M : EN-Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe
  • ASTM C1449/C1449M REV A : EN-Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe
  • ASTM C145 : EN-STANDARD SPECIFICATION FOR SOLID LOAD-BEARING CONCRETE MASONRY UNITS (DISCONTINUED)
  • ASTM C1450 : EN-Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe
  • ASTM C1450/C1450M : EN-Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe
  • ASTM C1450/C1450M REV A : EN-Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe
  • ASTM C1451 : EN-Standard Practice for Determining Uniformity of Ingredients of Concrete from a Single Source
  • ASTM C1452 : EN-Standard Specification for Reinforced Autoclaved Aerated Concrete Elements
  • ASTM C1453 : EN-Standard Test Method for the Determination of Uranium by Ignition and the Oxygen to Uranium (O/U) Atomic Ratio of Nuclear Grade Uranium Dioxide Powders and Pellets
  • ASTM C1454 : EN-Standard Guide for Pyrophoricity/Combustibility Testing in Support of Pyrophoricity Analyses of Metallic Uranium Spent Nuclear Fuel
  • ASTM C1455 : EN-Standard Guide for Nondestructive Assay of Special Nuclear Material Holdup Using Gamma-Ray Spectroscopic Methods
  • ASTM C1456 : EN-Standard Test Method for the Determination of Uranium or Gadolinium or Both in Gadolinium Oxide-Uranium Oxide Pellets or by X-Ray Fluorescence (XRF)
  • ASTM C1457 : EN-Standard Test Method for Determination of Total Hydrogen Content of Uranium Oxide Powders and Pellets by Carrier Gas Extraction
  • ASTM C1458 : EN-Standard Test Method for Nondestructive Assay of Plutonium Tritium and 241 Am by Calorimetric Assay
  • ASTM C1459 : EN-Standard Specification of Non-Asbestos Fiber-Reinforced Cement Shake Shingle and Slate Roofing Systems
  • ASTM C146 : EN-Standard Test Methods for Chemical Analysis of Glass Sand
  • ASTM C146 REV A : EN-Standard Test Methods for Chemical Analysis of Glass Sand
  • ASTM C1460 : EN-Standard Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground
  • ASTM C1461 : EN-Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain Waste and Vent (DWV) Sewer Sanitary and Storm Plumbing Systems for Above and Below Ground Use
  • ASTM C1462 : EN-Standard Specification for Uranium Metal Enriched to More Than 15 % and Less Than 20 % 235U
  • ASTM C1463 : EN-Standard Practices for Dissolving Glass Containing Radioactive and Mixed Waste for Chemical and Radiochemical Analysis
  • ASTM C1464 : EN-Standard Specification for Bent Glass
  • ASTM C1465 : EN-Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
  • ASTM C1466 : EN-Standard Test Method for Graphite Furnace Atomic Absorption Spectrometric Determination of Lead and Cadmium Extracted from Ceramic Foodware
  • ASTM C1467/C1467M : EN-Standard Specification for the Installation of Molded Glass Fiber Reinforced Gypsum Parts
  • ASTM C1468 : EN-Standard Test Method for Transthickness Tensile Strength of Continous Fiber-Reinforced Advanced Ceramics at Ambient Temperature
  • ASTM C1469 : EN-Standard Test Method for Shear Strength of Joints of Advanced Ceramics at Ambient Temperature
  • ASTM C147 : EN-Standard Test Methods for Internal Pressure Strength of Glass Containers
  • ASTM C1470 : EN-Standard Guide for Testing the Thermal Properties of Advanced Ceramics
  • ASTM C1471 : EN-Standard Guide for the Use of High Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
  • ASTM C1472 : EN-Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
  • ASTM C1473 : EN-Standard test Method for Radiochemical Determination of Uranium Isotopes in Urine by Alpha Spectrometry
  • ASTM C1474 : EN-Standard Test Method for Analysis of Isotopic Composition of Uranium in Nuclear-Grade Fuel Material by Quadrupole Inductively Coupled Plasma-Mass Spectrometry
  • ASTM C1475 : EN-Standard Guide for Determination of Neptunium-237 in Soil
  • ASTM C1476 : EN-Standard Test Method for Analysis of Urine for Technetium-99 by Inductively Coupled Plasma-Mass Spectrometry
  • ASTM C1477 : EN-Standard Test Method for Isotopic Abundance Analysis of Uranium Hexafluoride and Uranyl Nitrate Solutions by Multi-Collector Inductively Coupled Plasma-Mass Spectrometry1
  • ASTM C1478 : EN-Standard Specification for Storm Drain Resilient Connectors between Reinforced Concrete Storm Sewer Structures Pipes and Laterals
  • ASTM C1478M : EN-Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures Pipes and Laterals [Metric]
  • ASTM C1478M REV A : EN-Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures Pipes and Laterals (Metric)
  • ASTM C1479 : EN-Standard Practice for Installation of Precast Concrete Sewer Storm Drain and Culvert Pipe Using Standard Installations
  • ASTM C1479 REV A : EN-Standard Practice for Installation of Precast Concrete Sewer Storm Drain and Culvert Pipe Using Standard Installations
  • ASTM C1479M : EN-Standard Practice for Installation of Precast Concrete Sewer Storm Drain and Culvert Pipe Using Standard Installations [Metric]
  • ASTM C1479M REV A : EN-Standard Practice for Installation of Precast Concrete Sewer Storm Drain and Culvert Pipe Using Standard Installations [Metric]
  • ASTM C148 : EN-STANDARD TEST METHODS FOR POLARISCOPIC EXAMINATION OF GLASS CONTAINERS
  • ASTM C1480 : EN-Standard Specification for Packaged Pre-Blended Dry Combined Materials for Use in Wet or Dry Shotcrete Application
  • ASTM C1480/C1480M : EN-Standard Specification for Packaged Pre-Blended Dry Combined Materials for Use in Wet or Dry Shotcrete Application
  • ASTM C1481 : EN-Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems(EIFS)
  • ASTM C1482 : EN-Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
  • ASTM C1483 : EN-Standard Specification for Exterior Solar Radiation Control Coatings on Buildings
  • ASTM C1483/C1483M : EN-Standard Specification for Exterior Solar Radiation Control Coatings on Buildings
  • ASTM C1484 : EN-Standard Specification for Vacuum Insulation Panels
  • ASTM C1485 : EN-Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using an Electric Radiant Heat Energy Source
  • ASTM C1486 : EN-Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings
  • ASTM C1487 : EN-Standard Guide for Remedying Strucutral Silicone Glazing
  • ASTM C1488 : EN-Standard Practice for Simulated Aging of Cellulosic Loose-Fill Insulation
  • ASTM C1489 : EN-Standard Specification for Lime Putty for Structural Purposes
  • ASTM C149 : EN-Standard Test Method for Thermal Shock Resistance of Glass Containers
  • ASTM C1490 : EN-Standard Guide for the Selection Training and Qualification of Nondestructive Assay (NDA) Personnel
  • ASTM C1491 : EN-Standard Specification for Concrete Roof Pavers
  • ASTM C1491 REV A : EN-Standard Specification for Concrete Roof Pavers
  • ASTM C1492 : EN-Standard Specification for Concrete Roof Tile
  • ASTM C1493 : EN-Standard Test Method for Non-Destructive Assay of Nuclear Material in Waste by Passive and Active Neutron Counting Using a Differential Die-Away System
  • ASTM C1494 : EN-Standard Test Methods for Determination of Mass Fraction of Carbon Nitrogen and Oxygen in Silicon Nitride Power
  • ASTM C1495 : EN-Standard Test Method for Effect of Surface Grinding on Flexure Strength of Advanced Ceramics
  • ASTM C1496 : EN-Standard Guide for Assessment and Maintenance of Exterior Dimension Stone Masonry Walls and Facades
  • ASTM C1497 : EN-Standard Specification for Cellulosic Fiber Stabilized Thermal Insulation
  • ASTM C1498 : EN-Standard Test Method for Hygroscopic Sorption Isotherms of Building Materials
  • ASTM C1498 REV A : EN-Standard Test Method for Hygroscopic Sorption Isotherms of Building Materials
  • ASTM C1499 : EN-Standard Test Method for Monotonic Equibiaxial Flexural Strength of Advanced Ceramics at Ambient Temperature
  • ASTM C14M : EN-STANDARD SPECIFICATION FOR CONCRETE SEWER STORM DRAIN AND CULVERT PIPE (METRIC) (AASHTO M86M)
  • ASTM C14M REV A : EN-Standard Specification for Nonreinforced Concrete Sewer Storm Drain and Culvert Pipe [Metric]
  • ASTM C150 : EN-Standard Specification for Portland Cement
  • ASTM C150 REV A : EN-Standard Specification for Portland Cement
  • ASTM C150 REV B : EN-STANDARD SPECIFICATION FOR PORTLAND CEMENT
  • ASTM C150/C150M : EN-Standard Specification for Portland Cement
  • ASTM C1500 : EN-Standard Test Method for Nondestructive Assay of Plutonium by Passive Neutron Multiplicity Counting
  • ASTM C1501 : EN-Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures
  • ASTM C1502 : EN-Standard Test Method for Determination of Total Chlorine and Fluorine in Uranium Dioxide and Gadolinium Oxide
  • ASTM C1503 : EN-Standard Specification for Silvered Flat Glass Mirror
  • ASTM C1504 : EN-Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains
  • ASTM C1504M : EN-Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric)
  • ASTM C1505 : EN-Standard Test Method For Determination of Breaking Strength of Ceramic Tiles by Three-Point Loading
  • ASTM C1506 : EN-Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters
  • ASTM C1507 : EN-Standard Test Method for Radiochemical Determination of Strontium-90 in Soil
  • ASTM C1508 : EN-Standard Test Method for Determination of Bromine and Chlorine in UF6 and Uranyl Nitrate by X-Ray Fluorescence (XRF) Spectroscopy
  • ASTM C1509 : EN-Standard Specification for Beaded Process Glass Pipe and Fittings
  • ASTM C151 : EN-STANDARD TEST METHOD FOR AUTOCLAVE EXPANSION OF PORTLAND CEMENT
  • ASTM C151 REV A : EN-Standard Test Method for Autoclave Expansion of Portland Cement
  • ASTM C151/C151M : EN-Standard Test Method for Autoclave Expansion of Hydraulic Cement
  • ASTM C1510 : EN-Standard Test Method for Color and Color Difference of Whitewares by Abriged Spectrophotometry
  • ASTM C1511 : EN-Standard Test Method for Determining the Water Retention (Repellency) Characteristics of Fibrous Glass Insulation (Aircraft Type)
  • ASTM C1512 : EN-Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products
  • ASTM C1513 : EN-Standard Specification for Steel Tapping Screws for Cold-Formed Steel Framing Connections
  • ASTM C1514 : EN-Standard Test Method for Measurement of 235U Fraction Using the Enrichment Meter Principle
  • ASTM C1515 : EN-Standard Guide for Cleaning of Exterior Dimension Stone Vertical And Horizontal Surfaces New or Existing
  • ASTM C1516 : EN-Standard Practice for Application of Direct-Applied Exterior Finish Systems
  • ASTM C1517 : EN-Standard Test Method for Determination of Metallic Impurities in Uranium Metal or Compounds by DC-Arc Emission Spectroscopy
  • ASTM C1518 : EN-Standard Specification for Precured Elastomeric Silicone Joint Sealants
  • ASTM C1519 : EN-Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
  • ASTM C1519 REV A : EN-Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
  • ASTM C1520 : EN-Standard Guide for Paintability of Latex Sealants
  • ASTM C1521 : EN-Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
  • ASTM C1521 REV A : EN-Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
  • ASTM C1522 : EN-Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes
  • ASTM C1523 : EN-Standard Test Method for Determining Modulus Tear and Adhesion Properties of Precured Elastomeric Joint Sealants
  • ASTM C1523 REV A : EN-Standard Test Method for Determining Modulus Tear and Adhesion Properties of Precured Elastomeric Joint Sealants
  • ASTM C1524 : EN-Standard Test Method for Water-Extractable Chloride in Aggregate (Soxhlet Method)
  • ASTM C1524 REV A : EN-Standard Test Method for Water-Extractable Chloride in Aggregate (Soxhlet Method)
  • ASTM C1525 : EN-Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching
  • ASTM C1526 : EN-Standard Specification for Serpentine Dimension Stone
  • ASTM C1527 : EN-Standard Specification for Travertine Dimension Stone
  • ASTM C1528 : EN-Standard Guide for Selection of Dimension Stone for Exterior Use
  • ASTM C1528 REV A : EN-Standard Guide for Selection of Dimension Stone for Exterior Use
  • ASTM C1529 : EN-Standard Specification for Quicklime Hydrated Lime and Limestone for Environmental Uses
  • ASTM C1529 REV A : EN-Standard Specification for Quicklime Hydrated Lime and Limestone for Environmental Uses
  • ASTM C1530 : EN-Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes Shingles and Slates with Designed Varying Profiles and Thicknesses
  • ASTM C1530/C1530M : EN-Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes Shingles and Slates with Designed Varying Profiles and Thicknesses
  • ASTM C1531 : EN-Standard Test Methods for In Situ Measurement Of Masonry Mortar Joint Shear Strength Index
  • ASTM C1532 : EN-Standard Guide for Selection Removal and Shipment of Masonry Assemblage Specimens from Existing Construction
  • ASTM C1532 REV A : EN-Standard Guide for Selection Removal and Shipment of Masonry Assemblage Specimens from Existing Construction
  • ASTM C1533 : EN-Standard Guide for General Design Considerations for Hot Cell Equipment
  • ASTM C1534 : EN-Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems
  • ASTM C1535 : EN-Standard Practice for Application of Exterior Insulation and Finish Systems Class PI
  • ASTM C1536 : EN-Standard Test Method for Measuring the Yield for Aerosol Foam Sealants
  • ASTM C1539 : EN-Standard Test Method for Determination of Technetium-99 in Uranium Hexafluoride by Liquid Scintillation Counting
  • ASTM C154 : EN-STANDARD TEST METHOD FOR WARPAGE OF REFRACTORY BRICK AND TILE OR DEVIATION FROM A PLANE SURFACE
  • ASTM C1540 : EN-Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
  • ASTM C1540 REV A : EN-Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
  • ASTM C1541 : EN-Standard Specification for Shielded Transition Couplings Using Flexible Poly Vinyl Chloride (PVC) Gaskets to Connect Dissimilar DWV Pipe and Fittings
  • ASTM C1542/C1542M : EN-Standard Test Method for Measuring Length of Concrete Cores
  • ASTM C1543 : EN-Standard Test Method for Determining the Penetration of Chloride Ion into Concrete by Ponding
  • ASTM C1545 : EN-Practice for Dispersing Pigments and Other Materials into Water-Based Suspensions with a High Intensity Mixer
  • ASTM C1546 : EN-Standard Guide for Installation of Gypsum Products in Concealed Radiant Ceiling Heating Systems
  • ASTM C1547 : EN-Standard Classification for Fusion-Cast Refractory Blocks and Shapes
  • ASTM C1548 : EN-Standard Test Method for Dynamic Young s Modulus Shear Modulus and Poisson s Ratio of Refractory Materials by Impulse Excitation of Vibration
  • ASTM C1549 : EN-Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer
  • ASTM C155 : EN-Standard Classification of Insulating Firebrick
  • ASTM C1550 : EN-Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel)
  • ASTM C1550 REV A : EN-Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel)
  • ASTM C1552 : EN-Standard Practice for Capping Concrete Masonry Units Related Units and Masonry Prisms for Compression Testing
  • ASTM C1552 REV A : EN-Standard Practice for Capping Concrete Masonry Units Related Units and Masonry Prisms for Compression Testing
  • ASTM C1553 : EN-Standard Guide for Drying Behavior of Spent Nuclear Fuel
  • ASTM C1554 : EN-Standard Guide for Materials Handling Equipment for Hot Cells
  • ASTM C1555 : EN-Standard Practice for Autoclaved Aerated Concrete Masonry
  • ASTM C1555 REV A : EN-Standard Practice for Autoclaved Aerated Concrete Masonry
  • ASTM C1556 : EN-Standard Test Method for Determining the Apparent Chloride Diffusion Coefficient of Cementitious Mixtures by Bulk Diffusion
  • ASTM C1557 : EN-Standard Test Method for Tensile Strength and Young-s Modulus of Fibers
  • ASTM C1558 : EN-Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation
  • ASTM C1559 : EN-Standard Test Method for Determining Wicking of Glass Fiber Blanket Insulation (Aircraft Type)
  • ASTM C156 : EN-STANDARD TEST METHOD FOR WATER RETENTION BY CONCRETE CURING MATERIALS
  • ASTM C156 REV A : EN-Standard Test Method for Water Retention by Concrete Curing Materials
  • ASTM C156 REV B : EN-Standard Test Method for Water Retention by Concrete Curing Materials
  • ASTM C1560 : EN-Standard Test Method for Hot Water Accelerated Aging of Glass-Fiber Reinforced Cement-Based Composites
  • ASTM C1561 : EN-Standard Guide for Determination of Plutonium and Neptunium in Uranium Hexafluoride by Alpha Spectrometry
  • ASTM C1562 : EN-Standard Guide for Evaluation of Materials Used in Extended Service of Interim Spent Nuclear Fuel Dry Storage Systems
  • ASTM C1563 : EN-Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain Waste Vent and Storm Piping Applications
  • ASTM C1564 : EN-Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
  • ASTM C1565 : EN-Standard Test Method for Determination of Pack-Set Index of Portland Cement
  • ASTM C1567 : EN-Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method)
  • ASTM C1568 : EN-Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Mechanical Uplift Resistance Method)
  • ASTM C1569 : EN-Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Wind Tunnel Method)
  • ASTM C157 : EN-Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete-AASHTO No.: T160
  • ASTM C157/C157M : EN-Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete
  • ASTM C1570 : EN-Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Air Permeability Method)
  • ASTM C1571 : EN-Standard Guide for Characterization of Radioactive and/or Hazardous Wastes for Thermal Treatment
  • ASTM C1572 : EN-Standard Guide for Dry Lead Glass and Oil-Filled Lead Glass Radiation Shielding Window Components for Remotely Operated Facilities
  • ASTM C1574 : EN-Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation
  • ASTM C1576 : EN-Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Flexural Testing (Stress Rupture) at Ambient Temperature
  • ASTM C1577 : EN-Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts Storm Drains and Sewers Designed According to AASHTO LRFD
  • ASTM C1577 REV A : EN-Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts Storm Drains and Sewers Designed According to AASHTO LRFD
  • ASTM C1579 : EN-Standard Test Method for Evaluating Plastic Shrinkage Cracking of Restrained Fiber Reinforced Concrete (Using a Steel Form Insert)
  • ASTM C158 : EN-STANDARD TEST METHODS FOR STRENGTH OF GLASS BY FLEXURE (DETERMINATION OF MODULUS OF RUPTURE) (R 1989) (E1-1989) (PNS 745:1989)
  • ASTM C1580 : EN-Standard Test Method for Water-Soluble Sulfate in Soil
  • ASTM C1581 : EN-Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage
  • ASTM C1581/C1581M : EN-Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage
  • ASTM C1581/C1581M REV A : EN-Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage
  • ASTM C1583 : EN-Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
  • ASTM C1583/C1583M : EN-Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
  • ASTM C1585 : EN-Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes
  • ASTM C1586 : EN-Standard Guide for Quality Assurance of Mortars
  • ASTM C1587 : EN-Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Compressive Strength Testing
  • ASTM C1587 REV A : EN-Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Compressive Strength Testing
  • ASTM C1589 : EN-Standard Practice for Outdoor Weathering of Construction Seals and Sealants
  • ASTM C159 : EN-Standard Specification for Vitrified Clay Filter Blocks
  • ASTM C1590 : EN-Standard Practice for Alternate Actinide Calibration for Inductively Coupled Plasma-Mass Spectrometry
  • ASTM C1591 : EN-Standard Test Method for Determination of the Modulus of Elasticity of AAC
  • ASTM C1592 : EN-Standard Guide for Nondestructive Assay Measurements
  • ASTM C1592/C1592M : EN-Standard Guide for Making Quality Nondestructive Assay Measurements
  • ASTM C1594 : EN-Standard Specification for Polyimide Rigid Cellular Thermal Insulation
  • ASTM C1597M : EN-Standard Specification for Gypsum Wallboard (Hard Metric Sizes)
  • ASTM C16 : EN-Standard Test Method for Load Testing Refractory Shapes at High Temperatures
  • ASTM C1600/C1600M : EN-Standard Specification for Rapid Hardening Hydraulic Cement
  • ASTM C1601 : EN-Standard Test Method for Field Determination of Water Penetration of Masonry Wall Surfaces
  • ASTM C1602/C1602M : EN-Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
  • ASTM C1603 : EN-Standard Test Method for Measurement of Solids in Water
  • ASTM C1603 REV A : EN-Standard Test Method for Measurement of Solids in Water
  • ASTM C1604/C1604M : EN-Standard Test Method for Obtaining and Testing Drilled Cores of Shotcrete
  • ASTM C1605 : EN-Standard Test Methods for Chemical Analysis of Ceramic Whiteware Materials Using Wavelength Dispersive X-Ray Fluorescence Spectrometry
  • ASTM C1606 : EN-Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware
  • ASTM C1607 : EN-Standard Test Method for Determination of -Microwave Safe for Reheating- for Ceramicware
  • ASTM C1608 : EN-Standard Test Method for Chemical Shrinkage of Hydraulic Cement Paste
  • ASTM C1609/C1609M : EN-Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
  • ASTM C1610/C1610M : EN-Standard Test Method for Static Segregation of Self-Consolidating Concrete Using Column Technique1
  • ASTM C1610/C1610M REV A : EN-Standard Test Method for Static Segregation of Self-Consolidating Concrete Using Column Technique
  • ASTM C1611/C1611M : EN-Standard Test Method for Slump Flow of Self-Consolidating Concrete
  • ASTM C1611/C1611M REV A : EN-Standard Test Method for Slump Flow of Self-Consolidating Concrete
  • ASTM C1611/C1611M REV B : EN-Standard Test Method for Slump Flow of Self-Consolidating Concrete
  • ASTM C1613 : EN-Standard Specification for Precast Concrete Grease Interceptor Tanks
  • ASTM C1614 : EN-Standard Practice for the Determination of237Np232Th235U and238U in Urine by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Gamma Ray Spectrometry
  • ASTM C1615 : EN-Standard Guide for Mechanical Drive Systems for Remote Operation in Hot Cell Facilities
  • ASTM C1616 : EN-Standard Test Method for Determining the Moisture content of Organic and Inorganic Insulation Materials by Weight
  • ASTM C1617 : EN-Standard Practice for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Metals
  • ASTM C1618 : EN-Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure
  • ASTM C1618M : EN-Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure [Metric]
  • ASTM C1619 : EN-Standard Specification for Elastomeric Seals for Joining Concrete Structures
  • ASTM C162 : EN-STANDARD DEFINITIONS OF TERMS RELATING TO GLASS AND GLASS PRODUCTS
  • ASTM C162 REV A : EN-Standard Terminology of Glass and Glass Products
  • ASTM C162 REV B : EN-STANDARD TERMINOLOGY OF GLASS AND GLASS PRODUCTS
  • ASTM C162 REV C : EN-STANDARD TERMINOLOGY OF GLASS AND GLASS PRODUCTS
  • ASTM C1620 : EN-Standard Specification for Aerosol Polyurethane and Aerosol Latex Foam Sealants
  • ASTM C1621/C1621M : EN-Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring
  • ASTM C1621/C1621M REV A : EN-Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring
  • ASTM C1621/C1621M REV B : EN-Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring
  • ASTM C1622/C1622M : EN-Standard Specification for Cold-Weather Admixture Systems
  • ASTM C1623 : EN-Standard Specification for Manufactured Concrete Masonry Lintels
  • ASTM C1624 : EN-Standard Test Method for Adhesion Strength and Mechanical Failure Modes of Ceramic Coatings by Quantitative Single Point Scratch Testing
  • ASTM C1625 : EN-Standard Test Method for Uranium and Plutonium Concentrations and Isotopic Abundances by Thermal Ionization Mass Spectrometry
  • ASTM C1628 : EN-Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe Using Rubber Gaskets
  • ASTM C1629/C1629M : EN-Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels
  • ASTM C163 : EN-Standard Practice for Mixing Thermal Insulating Cement Samples
  • ASTM C1630 : EN-Standard Guide for Development of Coverage Charts for Loose-Fill Thermal Building Insulations
  • ASTM C1631 : EN-Standard Specification for Cellular Polypropylene Thermal Insulation
  • ASTM C1634 : EN-Standard Specification for Concrete Facing Brick
  • ASTM C1635 : EN-Standard Test Method to Evaluate Adhesion/Cohesion Properties of a Sealant at Fixed Extension
  • ASTM C1636 : EN-Standard Guide for the Determination of Uranium-232 in Uranium Hexafluoride
  • ASTM C1636 REV A : EN-Standard Guide for the Determination of Uranium-232 in Uranium Hexafluoride
  • ASTM C1637 : EN-Standard Test Method for the Determination of Impurities in Plutonium Metal: Acid Digestion and Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) Analysis
  • ASTM C1638 : EN-Standard Guide for the Determination of Iodine-129 In Uranium Oxide
  • ASTM C1639 : EN-Standard Specification for Fabrication Of Cellular Glass Pipe And Tubing Insulation
  • ASTM C1642 : EN-Standard Practice for Determining Air Leakage Rates of Aerosol Foam Sealants and Other Construction Joint Fill and Insulation Materials
  • ASTM C1643 : EN-Standard Test Method to Measuring the Post Dispensing Volumetric Expansion of Aerosol Foam Sealants
  • ASTM C1644 : EN-Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes
  • ASTM C1645 : EN-Standard Test Method for Freeze-thaw and De-icing Salt Durability of Solid Concrete Interlocking Paving Units
  • ASTM C1645/C1645M : EN-Standard Test Method for Freeze-thaw and De-icing Salt Durability of Solid Concrete Interlocking Paving Units
  • ASTM C1646/C1646M : EN-Standard Practice for Making and Curing Test Specimens for Evaluating Frost Resistance of Coarse Aggregate in Air-Entrained Concrete by Rapid Freezing and Thawing
  • ASTM C1646/C1646M REV A : EN-Standard Practice for Making and Curing Test Specimens for Evaluating Resistance of Coarse Aggregate to Freezing and Thawing in Air-Entrained Concrete
  • ASTM C1647 : EN-Standard Practice for Removal of Uranium or Plutonium or both for Impurity Assay in Uranium or Plutonium Materials
  • ASTM C1648 : EN-Standard Guide for Choosing a Method for Determining the Index of Refraction and Dispersion of Glass
  • ASTM C1649 : EN-Standard Practice for Instrumental Transmittance Measurement of Color for Flat Glass Coated and Uncoated
  • ASTM C165 : EN-Standard Test Method for Measuring Compressive Properties of Thermal Insulations
  • ASTM C1650 : EN-Standard Practice for Instrumental Reflectance Measurement of Color for Flat Glass Coated and Uncoated
  • ASTM C1652/C1652M : EN-Standard Test Method for Measuring Optical Distortion in Flat Glass Products Using Digital Photography of Grids
  • ASTM C1655 : EN-Standard Classification of Fireclay and High-Alumina Mortars
  • ASTM C1656 : EN-Standard Guide for Measuring the Reactivity of Hydraulic Refractory Castables using Exothermic Profile
  • ASTM C1658/C1658M : EN-Standard Specification for Glass Mat Gypsum Panels
  • ASTM C166 : EN-Standard Test Method for Covering Capacity and Volume Change upon Drying of Thermal Insulating Cement
  • ASTM C1660 : EN-Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry
  • ASTM C1661 : EN-Standard Guide for Viewing Systems for Remotely Operated Facilities
  • ASTM C1662 : EN-Standard Practice for For Measurement of the Glass Dissolution Rate Using the Single-Pass Flow-Through Test Method
  • ASTM C1663 : EN-Standard Test Method for Measuring Waste Glass or Glass Ceramic Durability by Vapor Hydration Test
  • ASTM C1666/C1666M : EN-Standard Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement
  • ASTM C1667 : EN-Standard Test Method for Using Heat Flow Meter Apparatus to Measure the Center-of-Panel Thermal Resistivity of Vacuum Panels
  • ASTM C1668 : EN-Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating Ventilation and Air Conditioning (HVAC) Systems
  • ASTM C167 : EN-STANDARD TEST METHODS FOR THICKNESS AND DENSITY OF BLANKET OR BATT THERMAL INSULATIONS
  • ASTM C1671 : EN-Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging
  • ASTM C1672 : EN-Standard Test Method for Determination of Uranium or Plutonium Isotopic Composition or Concentration by the Total Evaporation Method Using a Thermal Ionization Mass Spectrometer
  • ASTM C1673 : EN-Standard Terminology of C26.10 Nondestructive Assay Methods
  • ASTM C1674 : EN-Standard Test Method for Flexural Strength of Advanced Ceramics with Engineered Porosity (Honeycomb Cellular Channels) at Ambient Temperatures
  • ASTM C1676 : EN-Standard Specification for Microporous Thermal Insulation
  • ASTM C1677 : EN-Standard Specification for Joints for Concrete Box Using Rubber Gaskets
  • ASTM C1678 : EN-Standard Practice for Fractographic Analysis of Fracture Mirror Sizes in Ceramics and Glasses
  • ASTM C1679 : EN-Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry
  • ASTM C168 : EN-Standard Terminology Relating to Thermal Insulation
  • ASTM C168 REV A : EN-STANDARD DEFINITIONS OF TERMS RELATING TO THERMAL INSULATING MATERIALS
  • ASTM C168 REV B : EN-Standard Terminology Relating to Thermal Insulation
  • ASTM C1681 : EN-Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain
  • ASTM C1682 : EN-Standard Guide for Characterization of Spent Nuclear Fuel in Support of Geologic Repository Disposal
  • ASTM C1683 : EN-Standard Practice for Size Scaling of Tensile Strengths Using Weibull Statistics for Advanced Ceramics
  • ASTM C1684 : EN-Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature-Cylindrical Rod Strength
  • ASTM C1685 : EN-Standard Specification for Pneumatically Applied High-Temperature Fiber Thermal Insulation for Industrial Applications
  • ASTM C1686 : EN-Standard Practice for Installation and Testing of Reinforced Autoclaved Aerated Concrete (AAC) Units
  • ASTM C1688/C1688M : EN-Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete
  • ASTM C1689 : EN-Standard Practice for Subsampling of Uranium Hexafluoride
  • ASTM C1689 REV A : EN-Standard Practice for Subsampling of Uranium Hexafluoride
  • ASTM C169 : EN-Standard Test Methods for Chemical Analysis of Soda-Lime and Borosilicate Glass
  • ASTM C1691 : EN-Standard Specification for Unreinforced Autoclaved Aerated Concrete (AAC) Masonry Units
  • ASTM C1692 : EN-Standard Practice for Construction and Testing of Autoclaved Aerated Concrete (AAC) Masonry
  • ASTM C1693 : EN-Standard Specification for Autoclaved Aerated Concrete (AAC)
  • ASTM C1694 : EN-Standard Specification for Reinforced Autoclaved Aerated Concrete (AAC) Elements
  • ASTM C1695 : EN-Standard Specification for Fabrication of Flexible Removable and Reusable Blanket Insulation for Hot Service
  • ASTM C1697 : EN-Standard Specification for Blended Supplementary Cementitious Materials
  • ASTM C1698 : EN-Standard Test Method for Autogenous Strain of Cement Paste and Mortar
  • ASTM C1699 : EN-Standard Test Method for Moisture Retention Curves of Porous Building Materials Using Pressure Plates
  • ASTM C170 : EN-Standard Test Method for Compressive Strength of Dimension Stone
  • ASTM C170/C170M : EN-Standard Test Method for Compressive Strength of Dimension Stone
  • ASTM C1701/C1701M : EN-Standard Test Method for Infiltration Rate of In Place Pervious Concrete
  • ASTM C1702 : EN-Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry
  • ASTM C1702 REV A : EN-Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry
  • ASTM C1703 : EN-Standard Practice for Sampling of Gaseous Uranium Hexafluoride
  • ASTM C1704/C1704M : EN-Standard Test Method for Sampling and Testing Structural Cementitious Panels
  • ASTM C1704/C1704M REV A : EN-Standard Test Method for Sampling and Testing Structural Cementitious Panels
  • ASTM C1705/C1705M : EN-Standard Specification for Structural Cementitious Panels
  • ASTM C1707 : EN-Standard Specification for Specification for Pozzolanic Hydraulic Lime for Structural Purposes
  • ASTM C171 : EN-Standard Specification for Sheet Materials for Curing Concrete
  • ASTM C171 REV A : EN-Standard Specification for Sheet Materials for Curing Concrete
  • ASTM C1710 : EN-Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • ASTM C1712 : EN-Standard Test Method for Rapid Assessment of Static Segregation Resistance of Self-Consolidating Concrete Using Penetration Test
  • ASTM C1713 : EN-Standard Specification for Mortars for the Repair of Historic Masonry
  • ASTM C1714/C1714M : EN-Standard Specification for Preblended Dry Mortar Mix for Unit Masonry
  • ASTM C1715 : EN-Standard Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems
  • ASTM C1716/C1716M : EN-Standard Specification for Compression Testing Machine Requirements for Concrete Masonry Units Related Units and Prisms
  • ASTM C1717 : EN-Standard Test Methods for Conducting Strength Tests of Masonry Wall Panels
  • ASTM C1718 : EN-Standard Test Method for Nondestructive Assay of Radioactive Material by Tomographic Gamma Scanning
  • ASTM C172 : EN-Standard Practice for Sampling Freshly Mixed Concrete-AASHTO T141
  • ASTM C172 REV A : EN-Standard Practice for Sampling Freshly Mixed Concrete
  • ASTM C1721 : EN-Standard Guide for Petrographic Examination of Dimension Stone
  • ASTM C1726/C1726M : EN-Standard Guide for Use of Modeling for Passive Gamma Measurements
  • ASTM C1729 : EN-Standard Specification for Aluminum Jacketing for Insulation
  • ASTM C173 : EN-STANDARD TEST METHOD FOR AIR CONTENT OF FRESHLY MIXED CONCRETE BY THE VOLUMETRIC METHOD
  • ASTM C173 REV A : EN-Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
  • ASTM C173/C173M : EN-Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method-El: November 2001
  • ASTM C173/C173M REV A : EN-Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
  • ASTM C1737 : EN-Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing
  • ASTM C174 : EN-STANDARD METHOD OF MEASURING LENGTH OF DRILLED CONCRETE CORES
  • ASTM C174/C174M : EN-Standard Test Method for Measuring Thickness of Concrete Elements Using Drilled Concrete Cores-AASHTO No.: T 148
  • ASTM C177 : EN-Standard Test Method for Steady-State Thermal Transmission Properities by Means of the Gaurded Hot Plate
  • ASTM C179 : EN-Standard Test Method for Drying and Firing Linear Change of Refractory Plastic and Ramming Mix Specimens
  • ASTM C180 : EN-STANDARD METHOD OF PANEL SPALLING TESTING FIRECLAY PLASTIC REFRACTORIES
  • ASTM C181 : EN-Standard Test Method for Workability Index of Fireclay and High-Alumina Plastic Refractories
  • ASTM C182 : EN-Standard Test Method for Thermal Conductivity of Insulating Firebrick
  • ASTM C183 : EN-STANDARD PRACTICE FOR SAMPLING AND THE AMOUNT OF TESTING OF HYDRAULIC CEMENT (AASHTO T127)
  • ASTM C183 REV A : EN-Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
  • ASTM C184 : EN-Standard Test Method for Fineness of Hydraulic Cement by the 150-Micrometer (No. 100) and 75-Micrometer (No. 200) Sieves
  • ASTM C185 : EN-STANDARD TEST METHOD FOR AIR CONTENT OF HYDRAULIC CEMENT MORTAR (AASHTO NO. T 137)
  • ASTM C185 REV A : EN-STANDARD TEST METHOD FOR AIR CONTENT OF HYDRAULIC CEMENT MORTAR (AASHTO T137)
  • ASTM C186 : EN-Standard Test Method for Heat of Hydration of Hydraulic Cement
  • ASTM C186 REV A : EN-Standard Test Method for Heat of Hydration of Hydraulic Cement
  • ASTM C187 : EN-Standard Test Method for Normal Consistency of Hydraulic Cement-AASHTO No.: T129

 

ASTM A , ASTM B ,  ASTM C 1 || 2 || 3 |,  ASTM D , ASTM E ASTM F , ASTM G ,

- ASTM 규격 및 시험상담은 E-Mail :info@anycerti.com 로 연락바랍니다.